2021 Kia K5 TSBs

(CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

INSPECTION/REPLACEMENT + ECU SW UPGRADE (SC288/SC288A) CLOSED & SUPERSEDED - This bulletin is now closed and superseded by SC356. This bulletin provided information to inspect the fuel evaporative system and, if necessary, replace the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through January 23, 2024. This bulletin also provides information to upgrade the ECU software logic. The subject vehicles may experience fuel tank swelling due to an issue with the PCSV check valve, which results in pressurized air to flow into the fuel tank. This may cause the Check Engine Light to illuminate, and in some cases, the engine to run rough, and/or an inability to refuel. These conditions may cause the vehicle to release air pollutant which exceed Federal and California standards.

is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)

(CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

replace the Integrated Thermal Management Module (ITM) and then upgrade the Engine Control Module ECM system software on certain K5 (DL3a) vehicles, in the event the Multifunction Indicator Lamp (MIL) is illuminated with DTC(s) P218100, P2181F0, and/or P2181F1 stored. This condition may occur due to degradation of the diaphragm inside the ITM. There are no drivability or other symptoms associated with this condition.

renotification advising that Kia is conducting a Voluntary Emissions Service Campaign on certain 2021-2024 MY K5 vehicles equipped with 1.6L Turbo Gas Direct Injection (GDI) engines to improve the logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations. Also, the subject vehicles will be inspected and, if necessary, the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve will be replaced with a new one.

that Kia is conducting a Voluntary Emissions Service Campaign on certain 2021-2024 MY K5 vehicles equipped with 1.6L Turbo Gas Direct Injection (GDI) engines to improve the logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations. Also, the subject vehicles will be inspected and, if necessary, the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve will be replaced with a new one.

This bulletin provided information to replace Purge Control Solenoid Valve (PCSV) on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through October 11, 2023. This is a special, limited-time parts collection program for research purposes. Dealers are to ship the removed PCSV assembly to KUS via the Mandatory Parts Request (MPR).

Kia is conducting a Voluntary Emissions Service Campaign on certain 2021-2024 MY K5 vehicles equipped with 1.6L Turbo Gas Direct Injection (GDI) engines to improve the logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations. Also, the subject vehicles will be inspected and, if necessary, the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve will be replaced with a new one.

(SC288/SC288A) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect the fuel evaporative system and, if necessary, replace the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through January 23, 2024. This bulletin also provides information to upgrade the ECU software logic. This bulletin provides information to inspect the fuel evaporative system and, if necessary, replace the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through January 23, 2024. This bulletin also provides information to upgrade the ECU software logic.

bulletin provides information to replace Purge Control Solenoid Valve (PCSV) on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through October 11, 2023. This is a special limited time parts collection program for research purposes. Dealers are to ship the removed PCSV assembly to KUS via the Mandatory Parts Request (MPR).

renotification advising that Kia is conducting a Voluntary Service Campaign to relocate and install an improved blower motor 40amp fuse, with an increased terminal width, within the front wiring harness fuse box assembly in certain 2021-2022 MY K5 vehicles that were originally sold in or are currently registered in one of the 7 high-heat states (AZ, FL, HI, LA, MS, NV, and TX).

INSPECTION/REPLACEMENT + ECU SW UPGRADE (SC288) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect the fuel evaporative system and, if necessary, replace the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through October 17, 2023. This bulletin also provides information to upgrade the ECU software logic. The subject vehicles may experience fuel tank swelling due to an issue with the PCSV check valve, which results in pressurized air to flow into the fuel tank. This may cause the Check Engine Light to illuminate, and in some cases, the engine to run rough, and/or an inability to refuel. These conditions may cause the vehicle to release air pollutant which exceed Federal and California standards.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to improve the Electric Oil Pump EOP operation logic of the automatic transmission A/T on some 2021-2023MY Sorento (MQ4a) vehicles produced from September 9, 2020 through December 29, 2023 and 2021-2023MY K5 (DL3a) vehicles produced from March 24, 2020 to December 18, 2023, equipped with a 2.5L T-GDI Theta III engines and 8-Speed Dual Clutch Transmissions (DCT). The affected vehicles may exhibit abnormal/harsh shifting, gear slipping, no gear engagement in Drive D and/or Reverse R shift selection, accompanied by a Malfunction Indicator Lamp (MIL) ON illuminated on the instrument cluster with DTC(s) P1C2D03, P1C2D1C, and/or P1C2E92 stored.

INSPECTION/REPLACEMENT + ECU SW UPGRADE (SC288) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect the fuel evaporative system and, if necessary, replace the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through October 17, 2023. This bulletin also provides information to upgrade the ECU software logic. The subject vehicles may experience fuel tank swelling due to an issue with the PCSV check valve, which results in pressurized air to flow into the fuel tank. This may cause the Check Engine Light to illuminate, and in some cases, the engine to run rough, and/or an inability to refuel. These conditions may cause the vehicle to release air pollutant which exceed Federal and California standards.

- This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect the fuel evaporative system and, if necessary, replace the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through October 17, 2023. This bulletin also provides information to upgrade the ECU software logic. The subject vehicles may experience fuel tank swelling due to an issue with the PCSV check valve, which results in pressurized air to flow into the fuel tank. This may cause the Check Engine Light to illuminate, and in some cases, the engine to run rough, and/or an inability to refuel. These conditions may cause the vehicle to release air pollutant which exceed Federal and California standards.

the replacement or servicing of transmission assemblies on all Kia vehicles equipped with Idle-Stop-Go (ISG) and High-Flow Electric Oil Pump (HF EOP). The HF EOP protective connector cover may NOT have been installed on a new or remanufactured transmission during assembly. The HF EOP connector may become contaminated with debris during shipping and/or with oil/coolant during installation.

FUSE RELOCATION (WTY037) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information associated with the Warranty Extension Program (WTY037) to inspect, and if necessary, relocate the Heating, Ventilation, and Air Conditioning (HVAC) blower motor 40-ampere fuse on certain 2021-2022MY K5 (DL3a) vehicles produced from March 27, 2020 through July 20, 2022. The HVAC system provides cooling and heating to help maintain a comfortable environment inside the vehicle. The blower motor provides primary airflow for the HVAC system. Extended use of the HVAC at high fan speeds may cause damage to the multi-fuse terminals for the HVAC blower motor circuit, which can cause the blower motor to become inoperative, resulting in reduced heat and air conditioning. The warranty coverage for repairs related to the HVAC blower motor have been extended from 5 years / 60,000 miles to 15 years / 180,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to improve the Electric Oil Pump EOP operation logic of the automatic transmission 'A/T on some 2021-2023MY Sorento (MQ4a) vehicles produced from September 9, 2020 through December 29, 2023 and 2021-2023MY K5 (DL3a) vehicles produced from March 24, 2020 to December 18, 2023, equipped with a 2.5L T-GDI Theta III engines and 8-Speed Dual Clutch Transmissions (DCT). The affected vehicles may exhibit abnormal/harsh shifting, gear slipping, no gear engagement in Drive D and/or Reverse R shift selection, accompanied by a Malfunction Indicator Lamp (MIL) ON illuminated on the instrument cluster with DTC(s) P1C2D03, P1C2D1C, and/or P1C2E92 stored.

FUSE RELOCATION (WTY037) - This bulletin provides information associated with the Warranty Extension Program (WTY037) to inspect, and if necessary, relocate the Heating, Ventilation, and Air Conditioning (HVAC) blower motor 40-ampere fuse on certain 2021-2022MY K5 (DL3a) vehicles produced from March 27, 2020 through July 20, 2022. The HVAC system provides cooling and heating to help maintain a comfortable environment inside the vehicle. The blower motor provides primary airflow for the HVAC system. Extended use of the HVAC at high fan speeds may cause damage to the multi-fuse terminals for the HVAC blower motor circuit, which can cause the blower motor to become inoperative, resulting in reduced heat and air conditioning. The warranty coverage for repairs related to the HVAC blower motor have been extended from 5 years / 60,000 miles to 15 years / 180,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

FUSE RELOCATION (SC307) - This bulletin provides the procedure to relocate the Heating, Ventilation, and Air Conditioning (HVAC) blower motor 40-ampere fuse on certain 2021-2022MY K5 (DL3a) vehicles produced from February 23, 2021 through May 3, 2021 that were originally sold in one of the 7 high-heat states (AZ, FL, HI, LA, MS, NV, and TX). The HVAC system provides cooling and heating to help maintain a comfortable environment inside the vehicle. The blower motor provides primary airflow for the HVAC system. Extended use of the HVAC at high fan speeds may cause damage to the multi-fuse terminals for the HVAC blower motor circuit, which can cause the blower motor to become inoperative, resulting in reduced heat and air conditioning.

extending the New Vehicle Limited Warranty coverage, to all owners, for repairs related to the Heating, Ventilation, and Air Conditioning (HVAC) blower motor in 2021-2022 MY K5 vehicles from 5 years / 60,000 miles to 15 years / 180,000 miles, whichever comes first, starting from the date the vehicle was first put into service. Extended use of the HVAC at high fan speeds may cause damage to the multi-fuse terminals for the HVAC blower motor circuit, which can cause the blower motor to become inoperative, resulting in reduced heat and air conditioning airflow.

dealer Parts and Service managers advising that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for repairs related to the Heating, Ventilation, and Air Conditioning (HVAC) blower motor in 2021-2022 MY K5 vehicles from 5 years / 60,000 miles to 15 years / 180,000 miles, whichever comes first, starting from the date the vehicle was first put into service. Extended use of the HVAC at high fan speeds may cause damage to the multi-fuse terminals for the HVAC blower motor circuit, which can cause the blower motor to become inoperative, resulting in reduced heat and air conditioning airflow

advising that Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for repairs related to the Heating, Ventilation, and Air Conditioning (HVAC) blower motor in 2021-2022 MY K5 vehicles from 5 years / 60,000 miles to 15 years / 180,000 miles, whichever comes first, starting from the date the vehicle was first put into service. Extended use of the HVAC at high fan speeds may cause damage to the multi-fuse terminals for the HVAC blower motor circuit, which can cause the blower motor to become inoperative, resulting in reduced heat and air conditioning airflow

conducting a Voluntary Service Campaign to relocate and install an improved blower motor 40amp fuse, with an increased terminal width, within the front wiring harness fuse box assembly in certain 2021-2022 MY K5 vehicles that were originally sold in or are currently registered in one of the 7 high-heat states (AZ, FL, HI, LA, MS, NV, and TX). Kia dealers will be instructed to relocate the blower motor 40-ampere fuse to another circuit within the multi-fuse which has an increased terminal width. In addition, Kia is extending the New Vehicle Limited Warranty coverage to all owners for repairs related to the HVAC blower motor in 2021-2022 MY K5 vehicles from 5 years / 60,000 miles to 15 years / 180,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

Service managers that Kia is conducting a Voluntary Service Campaign on certain 2021-2022 MY K5 vehicles, manufactured from February 23, 2021 through May 3, 2021, that were originally sold in or are currently registered in one of the 7 high-heat states (AZ. FL, HI, LA, MS, NV, and TX). Kia Dealers will be instructed to relocate the blower motor 40-ampere fuse to another circuit within the multi-fuse which has an increased terminal width. In addition, Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for repairs related to the HVAC blower motor in 2021-2022 MY K5 vehicles from 5 years / 60,000 miles to 15 years / 180,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

that Kia is conducting a Voluntary Service Campaign on certain 2021-2022 MY K5 vehicles, manufactured from February 23, 2021 through May 3, 2021, that were originally sold in or are currently registered in one of the 7 high-heat states (AZ. FL, HI, LA, MS, NV, and TX). Kia Dealers will be instructed to relocate the blower motor 40-ampere fuse to another circuit within the multi-fuse which has an increased terminal width. In addition, Kia is extending the New Vehicle Limited Warranty coverage, to all owners, for repairs related to the HVAC blower motor in 2021-2022 MY K5 vehicles from 5 years / 60,000 miles to 15 years / 180,000 miles, whichever comes first, starting from the date the vehicle was first put into service.

information to improve the Electric Oil Pump EOP operation logic of the automatic transmission A/T on some 2021-2023MY Sorento (MQ4a) vehicles produced from September 9, 2020 through December 29, 2023 and 2021-2023MY K5 (DL3a) vehicles produced from March 24, 2020 to December 18, 2023, equipped with a 2.5L T-GDI Theta III engines and 8-Speed Dual Clutch Transmissions (DCT).

INSPECTION/REPLACEMENT + ECU SW UPGRADE (SC288) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect the fuel evaporative system and, if necessary, replace the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through October 17, 2023. This bulletin also provides information to upgrade the ECU software logic.

that Kia is conducting a Voluntary Emissions Service Campaign on certain 2021-2024 MY K5 vehicles equipped with 1.6L Turbo Gas Direct Injection (GDI) engines to improve the logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations. Also, the subject vehicles will be inspected and, if necessary, the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve will be replaced with a new one.

INSPECTION/REPLACEMENT + ECU SW UPGRADE (SC288) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect the fuel evaporative system and, if necessary, replace the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through October 17, 2023. This bulletin also provides information to upgrade the ECU software logic.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to replace the AWD coupling actuator assembly on some 2021-2024MY Kia AWD models listed on page 4. The affected vehicles may exhibit an inoperative AWD system (also referred to as 4WD) capability concern which may be caused by abnormal wear of the motor brushes inside the actuator assembly. This condition will cause the warning lamps on the instrument cluster to illuminate with stored DTC(s) P195800 and/or P19600.

INSPECTION/REPLACEMENT + ECU SW UPGRADE (SC288) - This bulletin provides information to inspect the fuel evaporative system and, if necessary, replace the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve on certain 2021-2024MY K5 (DL3a) vehicles equipped with a Gamma II 1.6L T-GDI engine, produced from March 27, 2020 through October 17, 2023. This bulletin also provides information to upgrade the ECU software logic.

Kia is conducting a Voluntary Emissions Service Campaign on certain 2021-2024 MY K5 vehicles equipped with 1.6L Turbo Gas Direct Injection (GDI) engines to improve the logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations. Also, the subject vehicles will be inspected and, if necessary, the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve will be replaced with a new one.

to the dealer Parts and Service Managers that Kia is conducting a Voluntary Emissions Service Campaign on certain 2021-2024 MY K5 vehicles equipped with 1.6L Turbo Gas Direct Injection (GDI) engines manufactured from March 27, 2020 through October 17, 2023 to improve the logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations. Also, the subject vehicles will be inspected and, if necessary, the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve will be replaced with a new one.

that Kia is conducting a Voluntary Emissions Service Campaign on certain 2021-2024 MY K5 vehicles equipped with 1.6L Turbo Gas Direct Injection (GDI) engines manufactured from March 27, 2020 through October 17, 2023 to improve the logic in the Electronic Control Module (ECM) to ensure compliance with emissions regulations. Also, the subject vehicles will be inspected and, if necessary, the fuel tank and/or the Purge Control Solenoid Valve (PCSV) check valve will be replaced with a new one.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect for a knocking/clicking noise present in the rear of the vehicle during low-speed driving (25MPH or less) on some 2020-2022MY Kia vehicles equipped with All Wheel Drive (AWD). The 4WD coupling snap ring may have excessive play between the drive gear set shaft and coupling flange.

to inspect for a knocking/clicking noise present in the rear of the vehicle during low-speed driving (25MPH or less) on some 2020-2022MY Kia vehicles equipped with All Wheel Drive (AWD). The 4WD coupling snap ring may have excessive play between the drive gear set shaft and coupling flange.

the AWD coupling actuator assembly on some 2021-2023MY Kia AWD models listed on page 4. The affected vehicles may exhibit an inoperative AWD system (also referred to as 4WD) capability concern which may be caused by abnormal wear of the motor brushes inside the actuator assembly. This condition will cause the warning lamps on the instrument cluster to illuminate with stored DTC(s) P195800 and/or P19600.

residue found on the coolant reservoir of some 2021-2023MY K5 (DL3a) vehicles equipped with a 1.6L T-GDI engine. The coolant reservoir on these Kia models was designed with a coolant overflow port located in the rear of the reservoir. During normal vehicle operation, coolant level may rise at or above the overflow port which can seep out of the coolant reservoir, therefore causing coolant to flow out and accumulate around the center seam of the reservoir. This may lead technicians to believe the coolant reservoir is faulty.

include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. Attention Dealership Service Managers, Service and Lube Techs, pay particular attention to this information. This Pitstop provides information regarding potential engine damage if the proper procedures are not followed during an oil change on the vehicles listed above equipped with 2.5L/2.5L-T GDI Theta III engines. Prior to installing: The oil filter service kit should be inspected for missing parts, if any of the parts are missing from the oil filter kit, inspect the oil filter carefully as parts can be dislodged during shipping.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software logic of the A/T system on certain 2021-2023MY K5 (DL3a) and 2021-2022MY Sorento (MQ4a) vehicles equipped with Theta 2.5L T-GDI engine and 8-Speed DCT. The affected vehicles may exhibit an abnormal shifting condition while driving, due to the amount of clutch oil flow consumption immediately after starting. In some cases, the cluster may display a transmission error message and/or MIL ON with DTC P086800 stored.

bulletin provides information to update the software logic of the A/T system on certain 2021-2023MY K5 (DL3a) and 2021-2022MY Sorento (MQ4a) vehicles equipped with Theta 2.5L T-GDI engine and 8-Speed DCT. The affected vehicles may exhibit an abnormal shifting condition while driving, due to the amount of clutch oil flow consumption immediately after starting. In some cases, the cluster may display a transmission error message and/or MIL ON with DTC P086800 stored.

pressure information stored in the Transmission Control Module (TCM) prior to replacement of the reman transmission assembly on some 2021MY~ Sorento (MQ4a) and K5 (DL3a) vehicles, equipped with Theta III 2.5 T-GDI engine which may set transmission DTC(s) or have an external/internal leak condition or other concern.

provides the procedure to update the software logic of the Engine Control Module (ECM) system on some 2021-2022MY K5 (DL3a) vehicles equipped with the Gamma 1.6L T-GDI engine produced from March 27, 2020 through January 10, 2022, which may exhibit an MIL ON with DTC P00B7 and/or RPM fluctuation and possible stalling when turning A/C 'OFF' while vehicle is parked.

Managers, Service and Lube Techs, pay particular attention to this information. This Pitstop provides information regarding potential engine damage if the proper procedures are not followed during an oil change on some 2021 and later K5 (DL3a) and Sorento (MQ4a) vehicles equipped with 2.5L/2.5L-T GDI Theta III engines.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

the small bearing of the Column Motor Driven Power Steering (C-MDPS) unit on the vehicles listed below, which may exhibit an abnormal noise when steering left and right. This may be caused by foreign substances in the MDPS worm shaft small bearing. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Small Bearing and does not affect the steering effort.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

provides information regarding the availability of partial repair (depending on faulty components) of the Dual Pinion Motor Driven Power Steering (DP-MDPS) system on some 2016-2021MY~ Kia vehicles (refer to the table below) in order to enhance customer satisfaction by promoting a cost-effective repair/replacement of a faulty related part, instead of replacement of the complete DP-MDPS assembly.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to extracting in use performance tracking emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to extracting in use performance tracking emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting.

New/revised sections of this bulletin are indicated by a black bar in the margin area. Some 2021MY Seltos (SP2), K5 (DL3A) and Sorento (MQ4a, MQ4 KH) models are equipped with a new Auto-Shut Off feature, which automatically shuts off the engine after a set time period. This feature will help reduce fuel consumption and prevent carbon monoxide (CO) poisoning.

bulletin provides information to inspect and if necessary, adjust the low pressure fuel line routing on some 2021MY K5 (DL3a) vehicles with GAMMA 1.6L T-GDI engine, produced from March 27, 2020 through July 23, 2020 which may NOT have been properly routed during assembly. The incorrectly routed fuel line may cause a Malfunction Indicator Lamp (MIL) with DTC P0087 and the vehicle may exhibit poor acceleration and/or hesitation during low speed operation.

Alert (ROA) with Rear Door Logic system on 2021MY K5 (DL3a) and Seltos (SP2) models. This system is designed to help prevent a rear passenger from being left inside the vehicle when exiting. When you open the front door after opening and closing the rear door and turning off the engine, the Check Rear Seats warning message appears on the cluster.

Off feature, which automatically shuts off the engine after a set time period. This feature will help reduce fuel consumption and prevent carbon monoxide (CO) poisoning.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software on Display Audio 2.0 (D2V) and AVN 5.0 Wide (AVN5W) head units on certain 2021-2023MY Kia vehicles (refer to pages 5 and 16). The affected vehicles may experience Apple CarPlay/Android Auto phone projection connectivity-related concerns.

Dealer Mode Factory Reset on multiple 2020-2021MY vehicles (listed on page 5) equipped with AVN 5.0 Wide head units. The affected vehicles may exhibit inoperable and/or interrupted Kia Connect services due to a logic error with the current software version. This logic error may affect the Kia Connect services: calendar, weather, sports, vehicle diagnostics, maintenance and/or Kia Connect services rendering these features inoperable.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software on 5th Generation AVN wide on certain 2020-2024MY Kia vehicles (refer to model list on page 8) to remedy a non-responsive or inoperative radio (FM, AM, SXM, etc.) concern. The affected AVN unit on the vehicles may not respond when pressing the RADIO hard key/button on the AVN unit or when selecting the RADIO icon on the AVN menu screen.

software on Display Audio 2.0 (D2V) and 5th Generation AVN Wide (AVN5W) head units on certain 2021-2023MY Kia vehicles. The affected vehicles may experience Apple CarPlay/Android Auto phone projection connectivity-related concerns.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software on 5th Generation AVN wide on certain 2020-2024MY Kia vehicles (refer to model list on page 3) to remedy a 'non-responsive' or 'inoperative' radio (FM, AM, SXM, etc. ) concern. The affected AVN unit on the vehicles may not respond when pressing the 'RADIO' hard key/button on the AVN unit or when selecting the 'RADIO' icon on the AVN menu screen.

information to update the software on 5th Generation AVN wide on certain 2020-2023MY Kia vehicles to remedy an inaccurate map location, freezing AVN screen, or experiencing a delay when using Google Maps or Waze through wired Apple CarPlay.

information to update the software on 5th Generation AVN wide on certain 2020-2023MY Kia vehicles (refer to model list on page 3) to remedy a warning sound accompanied by a 'Slippery road ahead. Drive carefully' or 'Uneven road ahead. Drive carefully' warning which is displayed on the instrument cluster. The current AVN software causes the warning sound and message to repeat approximately every ten (10) seconds, if the vehicle is not in motion, in 'PARK' or driving on even surfaces.

(refer to model list on page 3) to remedy a 'non-responsive' or 'inoperative' radio (FM, AM, SXM, etc. ) concern. The affected AVN unit on the vehicles may not respond when pressing the 'RADIO' hard key/button on the AVN unit or when selecting the 'RADIO' icon on the AVN menu screen.

been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to update the head unit software on some 2021MY K5 (DL3a), Sorento (MQ4a), and Sorento Hybrid (MQ4 HEV) vehicles equipped with a Display Audio 2.0 Value head unit, which may exhibit a wireless CarPlay connectivity issue with Apple phones running iOS14 software version.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop contains information regarding the log file collection procedure for 2020MY~ models equipped with AVN 5.0/W or Display Audio 2.0 head units.

the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster. The KDS is required to change the setting from "Workshop" to "Customer Mode."

a memory concern with the AVN 5.0 Wide head unit while downloading the contact list from a paired phone. The concern also affects Voice Recognition (VR) functionality.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop contains information regarding the log file collection procedure for 2020MY~ models equipped with AVN 5.0/W or Display Audio 2.0 head units.

been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to update the head unit software on some 2021MY K5 (DL3a), Sorento (MQ4a), and Sorento Hybrid (MQ4 HEV) vehicles equipped with a Display Audio 2.0 Value head unit, which may exhibit a wireless CarPlay connectivity issue with Apple phones running iOS14 software version.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to turn OFF the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to turn OFF the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster.

file collection procedure for 2020MY~ models equipped with AVN 5.0/W or Display Audio 2.0 head units.

ISSUE (SA460) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to update the head unit software on some 2021MY K5 (DL3a), Sorento (MQ4a), and Sorento Hybrid (MQ4 HEV) vehicles equipped with a Display Audio 2.0 head unit, which may exhibit a wireless CarPlay connectivity issue with Apple phones running iOS14 software version.

bulletin provides the procedure to update the head unit software on some 2021MY K5 (DL3a), Sorento (MQ4a), and Sorento Hybrid (MQ4 HEV) vehicles (refer to affected vehicle range on page 6), equipped with a Display Audio 2.0 head unit, which may exhibit a wireless CarPlay connectivity issue with Apple phones running iOS14 software version.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop provides diagnostic information to guide in diagnosis of suspected defective door speakers on some Kia vehicles.

the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster.

provides information to inspect and if necessary update the navigation software on some 2021 K5 (DL3a) vehicles produced from March 27, 2020 through August 3, 2020, equipped with AVN 5-Wide head units, which may exhibit a distorted image display when navigation goes into the split screen mode (displaying upcoming change in route to a set destination) due to corrupted software file(s).

This feature will be available on the UVO Link Audio Unit (Display Audio 2.0 Value) and will not be available on the UVO Link with Navigation Audio Unit (AVN 5.0 Wide). The UVO Link with Navigation unit will still support wired CarPlay. This Pitstop provides information on wireless vs wired phone projection capability per headunit, the pairing and removal process for wireless phone projection, and troubleshooting tips.

This feature will be available on the UVO Link Audio Unit (Display Audio 2.0 Value) and will not be available on the UVO Link with Navigation Audio Unit (AVN 5.0 Wide). The UVO Link with Navigation unit will still support wired Android Auto. This Pitstop provides information on wireless vs wired phone projection capability per headunit, the pairing and removal process for wireless phone projection, and troubleshooting tips.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2021-2022MY K5 vehicles produced from March 27, 2020 through December 21, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.

COMPATIBILITY (CS2310) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 7. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2021-2022MY K5 vehicles produced from March 27, 2020 through December 21, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

COMPATIBILITY (CS2310) - This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 6. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2021-2022MY K5 vehicles produced from March 27, 2020 through December 21, 2021, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2021-2022MY K5 vehicles produced from March 27, 2020 through December 21, 2021, which may not be equipped with and immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to update the software logic of the Integrated Body Control Unit (IBU) system on some 2021-2022MY K5 (DL3a) vehicles produced from March 27, 2020 through May 12, 2022, which may exhibit excessive discharge of the smart key battery. Follow the procedure outlined in this publication to apply the improved logic to the "IBU" system using the KDS ECU Upgrade function as described in this bulletin and replace the batteries on both of the customers key fobs.

developed a software upgrade that can be installed on your vehicle to restrict the operation of the vehicle's ignition system should the locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available free of charge for eighteen (18) months from the date of this letter. When the software upgrade is completed, Kia will also provide you with window stickers that can be applied to your vehicle to discourage a break-in.

bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on some 2021-2022MY K5 vehicles produced from March 27, 2020 through December 21, 2021, which may not be equipped with and immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop provides information regarding a new interface related to the electronic Dealer (Shipping) / Customer Mode Switch setting on all applicable models.

alignment on 2014MY and later vehicles that may exhibit a warning light ON related to radar sensor alignment errors in the Forward Collision-Avoidance Assist (FCA)/Smart Cruise Control (SCC) system.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop provides information regarding a new interface related to the electronic Dealer / Customer Mode Switch setting on multiple models.

This bulletin provides information regarding the front passenger seat harness on some 2021MY K5 (DL3a) vehicles produced from March 27, 2020 through June 19, 2020, which may have had an incorrect passenger seat harness installed during assembly.

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

with the All-Wheel-Drive (AWD) system due to tire sizes of differing circumference. Some customers may complain of a chatter sensation felt in the drivetrain of the vehicle and/or the failure of drivetrain component(s). A difference in tire size (width, aspect ratio, construction, rim diameter etc.) may be the cause.

Dual Clutch Transmission (WDCT) assembly on some 2021-2023MY K5 (DL3a) and Sorento (MQ4a) vehicles, where the High Flow Electric Oil Pump (HF EOP) protective connector cover may NOT be installed on the new/remanufactured WDCT assembly during production or remanufacturing. The HF EOP connector may become contaminated during shipping and/or may become contaminated with oil and/or coolant during installation.

IMPROVEMENT (SA502) - SA502 superseded by SA526, TSB CLOSED.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

information to inspect for judder in the 8-speed Wet Dual Clutch Transmission (WDCT) and possibly replace the Dual Clutch Assembly on some 2021MY~ K5 GT (DL3a) vehicles produced from November 16, 2020 and later and Sorento EX trim and above (MQ4a) non-hybrid vehicles, produced from October 26, 2020 and later, which may exhibit clutch judder. If the vehicle body vibrates without the steering wheel shuddering when performing the creep driving test (driving the vehicle up to 3mph), the vehicle is exhibiting clutch judder. The creep test can be conducted by driving at a speed slower than 5 mph after releasing the brake.

clarification on what appears to be a water leak and/or condensation in the rear center combination lamp assembly on some 2021MY~ K5 (DL3a) vehicles. The top area of the rear center combination lamp assembly can have the appearance of condensation behind the lens. This is a normal condition for water and/or condensation to be present above the sonic weld line. As the weld forms a lip along the top of the rear combination lamp, water may enter the back side of the lens but does not actually enter the inside of the lamp housing. Replacement of the rear center combination lamp is not necessary.

procedure to inspect and if necessary, repair a left front bolt of the Panorama Sunroof tracking system on some 2021MY K5 (DL3A) vehicles produced between March 16, 2021 through April 22, 2021, in which the bolt may not have been properly installed during vehicle assembly and cause a creek noise as the body flexes.

New/revised sections of this bulletin are indicated by a black bar in the margin area. When servicing windshield wipers on the below listed vehicles, including during PDI, ensure to raise the wiper arms to a vertical position to avoid damaging the paint on the rear edge of the hood.

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to inspect and if necessary, repair the three (3) items listed in the table below on some 2021 K5 (DL3A) vehicles produced between March 27, 2020 through July 14, 2020, for which the parts described may not have been properly installed during assembly.

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to inspect and if necessary, repair the three (3) items listed in the table below on some 2021 K5 (DL3A) vehicles produced between March 27, 2020 through July 14, 2020, for which the parts described may not have been properly installed during assembly.

This bulletin provides the procedure to inspect and, if necessary, repair the three (3) items listed in the table below on some 2021 K5 (DL3A) vehicles produced between March 27, 2020 through July 14, 2020, for which the parts described may not have been properly installed during assembly.

resetting the modem in certain 2016-2025MY Kia vehicles listed on page 3 that are equipped with Kia Connect Services. The affected vehicles may encounter the following issues: remote Start/Climate Control function not working, vehicle Status on the Kia Access App not updating, connected routing not functioning properly.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding a potential squeak noise between the Heating Ventilation Air Condition (HVAC) controller and the floor console upper garnish on some 2021-2022MY K5 (DL3a) produced from March 25, 2020 through June 8, 2021.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding a potential squeak noise between the Heating Ventilation Air Condition (HVAC) controller and the floor console upper garnish on some 2021MY K5 (DL3a) produced from March 25, 2020 through to February 23, 2021.

has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to inspect and adjust the clearance between the A/C discharge hose and the A/C compressor pulley. If there is evidence of A/C compressor pulley to discharge hose damage, then replacement of the discharge hose is required. Additionally, inspect the sunvisor(s) operation and appearance as listed in the table below; both procedures apply to some 2021MY K5 (DL3A) vehicles produced between March 27, 2020 through July 14, 2020.

provides the procedure to inspect and adjust the clearance between the A/C discharge hose and the A/C compressor pulley, if there is evidence of A/C compressor pulley to discharge hose damage, then replacement of the discharge hose is required, and then inspect the sunvisor(s) operation and appearance as listed in the table below on some 2021MY K5 (DL3A) vehicles produced between March 27, 2020 through July 14, 2020.

information regarding a potential squeak noise between the Heating Ventilation Air Condition (HVAC) controller and the floor console upper garnish on some 2021MY K5 (DL3a) produced from March 25, 2020 through September 7, 2020.

procedure to replace the fuel filler door housing and actuator assembly on some 2021-2022MY K5 (DL3a) vehicles produced from March 24, 2020 through August 11, 2021 which may have fuel doors that exhibit an inability to open/close or intermittent lock/unlock concerns due to trapped moisture in the fuel door actuator. During normal operation, moisture may become trapped in the affected vehicles fuel filler door housing. Trapped moisture/water may enter the fuel door actuator, preventing the actuator operating normally. The new fuel door housing replacement part features a drainage port hole in the actuator casing to release any moisture that may collect in the fuel door housing.

containing the most frequently asked questions regarding the Voluntary Emissions Service Campaign SC288.

access and remove the fuel door actuator on 2021MY K5 (DL3a) vehicles, to help minimize breaking of the fuel door lid when the fuel door has a stuck closed condition.

that was mailed with the customer letter advising them to submit the form if they had paid for repairs for this same matter prior to the warranty extension campaign program launch.

was mailed with the customer letter advising them to submit the form if they had paid for repairs for this same matter prior to the voluntary service campaign program launch.

ensure proper internal connections of the headlamp on some 2021MY K5 (DL3a) vehicles produced from March 27, 2020 through April 14, 2021 and some 2020-2021MY Telluride (ON) vehicles produced from January 9, 2019 through April 12, 2021, which may exhibit inoperative/intermittently inoperative LED low beam or Daytime Running Lights (DRL) on K5, or low/sub-low beam on Telluride.

procedure to replace the multifunction camera (MFC) on some 2021MY K5 (DL3a) vehicles produced between September 1, 2020 through September 16, 2020 due to an internal control chip concern inside of the camera which may illuminate warning lights in the instrument cluster and/or MIL ON with DTC C160449.

the most frequently asked questions regarding the Warranty Extension Campaign WTY037.

most frequently asked questions regarding the Voluntary Service Campaign SC307.

New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information on setting the "Service Interval Reminder" feature available on most 2014-2023MY Kia vehicles (refer to model list on page 2). If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance. Refer to TSB ENG241 for 2023MY~ vehicles equipped with the Oil Life Management System (OLMS) feature not included in table on page 2.

Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop provides information regarding the Rear Occupant Alert (ROA) with Rear Door Logic system on all 21MY~ models equipped with this feature. This system is designed to help prevent a rear passenger from being left inside the vehicle when exiting. The "Check Rear Seats" message will display on the cluster when driver opens the front door, if during vehicle operation the rear doors (one or both) were opened and closed.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

In the event a wheel alignment is needed, ensure your alignment equipment has the correct specifications programmed into the PC database.