2021 Kia Forte TSBs

(CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)

(CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to replace the Heating, Ventilation, and Air Conditioning (HVAC) blower motor connector on some 2019-2023MY Forte (BDm) vehicles produced from July 09, 2018 through present, which may experience the air conditioning function inoperative. The blower motor connector pins may have poor pin tension. Poor pin tension occurs when the female pin is slightly open which will not allow for a proper electrical connection. While driving, the road conditions can cause the connector pin to slightly move within the connector and will intermittently make contact with the male pin. This can cause excessive circuit resistance, causing the blower motor to become inoperative. Follow the procedure outlined in this publication to replace the HVAC blower motor connector.

Heating, Ventilation, and Air Conditioning (HVAC) blower motor connector on some 2019-2023MY Forte (BDm) vehicles produced from July 09, 2018 through present, which may experience the air conditioning function inoperative. The blower motor connector pins may have poor pin tension. Poor pin tension occurs when the female pin is slightly open which will not allow for a proper electrical connection. While driving, the road conditions can cause the connector pin to slightly move within the connector and will intermittently contact the male pin. This may cause excessive circuit resistance, causing the blower motor to become inoperative.

loose crankshaft pulley condition on certain 2020-2023MY Forte (BDm) vehicles equipped with a 1.6L T-GDI and 6-speed manual transmission, produced from May 15, 2019 through present, where excessive engine loads may cause the crankshaft pulley bolt to back out, causing the crankshaft pulley to come loose. If this condition occurs, a loose crankshaft pulley may cause the alignment dowel pin to shear and the crankshaft pulley to separate from the crankshaft.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

the small bearing of the Column Motor Driven Power Steering (C-MDPS) unit on the vehicles listed below, which may exhibit an abnormal noise when steering left and right. This may be caused by foreign substances in the MDPS worm shaft small bearing. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Small Bearing and does not affect the steering effort.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

modification of the fuel tank Inlet Check Valve (ICV) on some 2019-2021MY Forte (BDm) vehicles produced from July 9, 2018 through December 2, 2020, which may exhibit fuel spit-back from the Fuel Filler Neck, after the tank has been filled up, and the nozzle clicks off.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to extracting in use performance tracking emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to extracting in use performance tracking emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

COMPATIBILITY (CS2310) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 7. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

COMPATIBILITY (CS2310) - This bulletin provides information to update the software logic in the Kia Genuine Remote Start Control Module on certain 2012-2022MY model vehicles listed on page 6. Vehicles equipped with a Kia Genuine Remote Start feature and have had the Anti-Theft software logic (CS230*) applied to the Integrated Body Control Unit (IBU) or Body Control Module (BCM) may experience five (5) inadvertent honks after starting the vehicle with the remote start feature.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding A/C Compressor Field Coil Assembly inspection and replacement on some 2017-2018MY Forte (YDm) and 2019-2023MY Forte (BDm) vehicles.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop provides information regarding a new interface related to the electronic Dealer (Shipping) / Customer Mode Switch setting on all applicable models.

alignment on 2014MY and later vehicles that may exhibit a warning light ON related to radar sensor alignment errors in the Forward Collision-Avoidance Assist (FCA)/Smart Cruise Control (SCC) system.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop provides information regarding a new interface related to the electronic Dealer / Customer Mode Switch setting on multiple models.

replace the LED headlamp(s) on certain 2021MY Kia Forte (BDm) vehicles produced from October 28, 2020 through November 24, 2020. The LED headlamps installed on certain 2021MY Forte (BDm) vehicles may be assembled with the inappropriate LED Drive Module (LDM) and may turn ON the indicator lamp in the instrument cluster via IBU. The condition has no effect on normal operation for the low or high beams.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to update the software on 5th Generation AVN wide on certain 2020-2024MY Kia vehicles (refer to model list on page 3) to remedy a 'non-responsive' or 'inoperative' radio (FM, AM, SXM, etc. ) concern. The affected AVN unit on the vehicles may not respond when pressing the 'RADIO' hard key/button on the AVN unit or when selecting the 'RADIO' icon on the AVN menu screen.

update the software on 5th Generation AVN wide on certain 2020-2023MY Kia vehicles to remedy a 'non-responsive' or 'inoperative' radio (FM, AM, SXM, etc.) concern. The affected AVN unit on the vehicles may not respond when pressing the 'RADIO' hard key/button on the AVN unit or when selecting the 'RADIO' icon on the AVN menu screen. Follow the procedure outlined in this publication to update the software on 5th Generation AVN wide units using the applicable USB Flash Drive A or B for the applicable vehicle.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop contains information regarding the log file collection procedure for 2020MY~ models equipped with AVN 5.0/W or Display Audio 2.0 head units.

the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster. The KDS is required to change the setting from "Workshop" to "Customer Mode."

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop contains information regarding the log file collection procedure for 2020MY~ models equipped with AVN 5.0/W or Display Audio 2.0 head units.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to turn OFF the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to turn OFF the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster.

file collection procedure for 2020MY~ models equipped with AVN 5.0/W or Display Audio 2.0 head units.

operation of Multi-Function Camera (MFC) on some Kia vehicles. When normal operation is not possible due to certain outside environment conditions (such as sunlight glare, heavy rain, sunlight, snow, fog and/or substance/debris) causing a temporary concern. This stops operation causing Warning Lamp ON and/or Pop-up Message displayed on the cluster. This is a normal operation of the ADAS and once environment conditions improve and/or substance/debris are removed, the system will clear itself and operate normally.

the service reminder lamp, at the first service interval reminder alert that will display on the instrument cluster.

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

Intelligent Variable Transmission (IVT) Oil Pressure Sensor (OPS) on some 2018-2024MY vehicles listed on page 3 equipped with IVT. The affected vehicles may exhibit a malfunction indicator lamp (MIL) illuminated on the instrument cluster with DTCs P084500, P084600, and/or P0867XX present with no drivability concerns due to a failed IVT oil pressure sensor.

A flush is required ONLY when a transmission is replaced.

to update the Transmission Control Module (TCM) software logic and, if necessary, replace the Intelligent Variable Transmission (IVT) assembly on certain 2019-2021MY model vehicles listed in the chart below, which may exhibit an MIL ON with the DTC(s) listed below and a lack/delay in acceleration due to transmission slippage.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

to update the Transmission Control Module (TCM) software logic and, if necessary, replace the Intelligent Variable Transmission (IVT) assembly on certain 2019-2021MY model vehicles listed in the chart below, which may exhibit an MIL ON with the DTC(s) listed below and a lack/delay in acceleration due to transmission slippage. To correct this concern, if necessary, apply the improved software logic to the CVT system using the KDS ECU Upgrade function as described in this bulletin and replace the IVT assembly.

been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. (This bulletin was previously referred to as SA424 or ELE 200.) This bulletin provides the procedure to update the Transmission Control Module (TCM) software logic and, if necessary, replace the Intelligent Variable Transmission (IVT) on certain 2019-2021MY vehicles listed in the chart below. The affected vehicles may exhibit the illumination of MIL with the DTC(s) listed below in addition to a lack of acceleration or delay in accelerating due to transmission slippage.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to replace the front strut bearing and upper spring pad on both front (LH and RH) strut assemblies on certain 2019-2024MY Forte (BDm) vehicles produced from July 09, 2018 through present, 2020-2024MY Soul (SK3) vehicles produced from November 15, 2018 through present, and 2021-2024 Seltos (SP2) vehicles produced from November 20, 2019 through present. The affected vehicles may exhibit an intermittent noise when turning the steering wheel both when driving and when the vehicle is not in motion.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to replace the front strut bearing and upper spring pad on both front (LH and RH) strut assemblies on certain 2019-2024MY Forte (BDm) vehicles produced from July 09, 2018 through present, 2020-2024MY Soul (SK3) vehicles produced from November 15, 2018 through present, and 2021-2024 Seltos (SP2) vehicles produced from November 20, 2019 through present. The affected vehicles may exhibit an intermittent noise when turning the steering wheel both when driving and when the vehicle is not in motion.

the front strut bearing and upper spring pad on both front (LH and RH) strut assemblies on certain 2019-2024MY Forte (BDm) vehicles produced from July 09, 2018 through present, 2020-2024MY Soul (SK3) vehicles produced from November 15, 2018 through present, and 2021-2024 Seltos (SP2) vehicles produced from November 20, 2019 through present. The affected vehicles may exhibit an intermittent noise when turning the steering wheel both when driving and when the vehicle is not in motion.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect and repair an inoperative front seat mechanism on some 2019-2024MY Forte (BDm) vehicles produced from June 18, 2018 through Present and some 2018-2023MY Rio (SC) vehicles produced from January 2, 2017 through August 16, 2023. Symptoms of an inoperative front seat include the inability of the seat to move forward and backward, which may be caused by a pin getting stuck on a rail.

New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information on setting the "Service Interval Reminder" feature available on most 2014-2023MY Kia vehicles (refer to model list on page 2). If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance. Refer to TSB ENG241 for 2023MY~ vehicles equipped with the Oil Life Management System (OLMS) feature not included in table on page 2.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on the inspection and replacement of the front camera on some vehicles listed below. Due to an internal control chip concern inside the camera, the vehicle may exhibit an MIL on with DTC C160449 and/or C160649.

Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the service reminder setting, which may have been auto-set by the Kia Vehicle Inspection and Delivery application (KVID) at time of Pre-Delivery Inspection (PDI). Beginning with the 2023MY, Oil Life Monitoring (OLM) has been applied to all models, except Forte (BDm), Stinger (CK), Telluride (ON) and Soul (SK3). Refer to TSB ENG241 for additional information. As of 08/11/2023, the service reminder auto-set feature by KVID has been disabled for ALL models NOT equipped with OLM.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This pitstop provides the KDS service procedure for mileage setting on the models listed below with newly replaced instrument clusters. Certain models allow for mileage setting with the KDS, which prevents the need to send out the instrument cluster to a 3rd party for mileage adjustment (refer to PS264). After a new cluster is installed, cluster (variant) coding may also need to be conducted using the KDS. Make sure the KDS software is also updated to the latest version. Mileage setting should be performed by using the KDS only, as described in this bulletin.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on the inspection and replacement of the front camera on some vehicles. Due to an internal control chip concern inside the camera, the vehicle may exhibit a Forward Collision Avoidance Assist Warning Lamp (A) and/or Master Warning Lamp (B) with C160449 and/or C160649 codes. Certain systems may become temporarily disabled during occurrences: Smart Cruise Control (SCC), Lane Keep Assistance (LKA), Lane Departure Warning (LDW), Forward Collision-Avoidance Assist (FCA), Forward Collision Warning (FCW) and/or Driver Attention Warning (DAW).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on the inspection and replacement of the front camera on some vehicles. Due to an internal control chip concern inside the camera, the vehicle may exhibit a Forward Collision Avoidance Assist Warning Lamp (A) and/or Master Warning Lamp (B) with C160449 and/or C160649 codes. Certain systems may become temporarily disabled during occurrences: Smart Cruise Control (SCC), Lane Keep Assistance (LKA), Lane Departure Warning (LDW), Forward Collision-Avoidance Assist (FCA), Forward Collision Warning (FCW) and/or Driver Attention Warning (DAW).

the overhead console lamp assembly and sunglass door latch on some 2012-2023MY model vehicles listed in the table below, which may encounter the sunglass case of the overhead console lamp not closing properly.

New/revised sections of this bulletin are indicated by a black bar in the margin area. When servicing windshield wipers on the below listed vehicles, including during PDI, ensure to raise the wiper arms to a vertical position to avoid damaging the paint on the rear edge of the hood.

resetting the modem in certain 2016-2025MY Kia vehicles listed on page 3 that are equipped with Kia Connect Services. The affected vehicles may encounter the following issues: remote Start/Climate Control function not working, vehicle Status on the Kia Access App not updating, connected routing not functioning properly.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This Pitstop provides information regarding the Rear Occupant Alert (ROA) with Rear Door Logic system on all 21MY~ models equipped with this feature. This system is designed to help prevent a rear passenger from being left inside the vehicle when exiting. The "Check Rear Seats" message will display on the cluster when driver opens the front door, if during vehicle operation the rear doors (one or both) were opened and closed.