2018 Kia Forte TSBs

(CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)

(CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

Kia is conducting a Product Improvement Campaign to perform a software update on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter Nu GDI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (ECU).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

Kia is conducting an important Product Improvement Campaign to perform a software update on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter Nu GDI engines to protect the engine from excessive connecting rod bearing damage.

DTC P1326 (PI2106Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published (PI2106) titled Nu 2.0L GDI - Knock Sensor Detection System ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

Kia is conducting a Product Improvement Campaign to perform a software update on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

related to the Technical Service Bulletin previously published (PI2106) titled Nu 2.0L GDI - Knock Sensor Detection System ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

procedure to improve the logic of the Engine Control Module (ECM) on some 2017-2018MY Forte (YDm) vehicles equipped with the NU 2.0L MPI engine, produced from May 27, 2016 through June 27, 2018. While this issue has no effect on the drivability of the vehicle, nor does it release any air pollutants, the vehicle may fail a SMOG check and/or may not illuminate the Malfunction Indicator Light (MIL) for certain fuel system failures. In order to improve On-Board Diagnostics (OBD) logic, apply the improved software logic to the Engine system using the KDS ECU Upgrade function as described in this bulletin.

is conducting a Voluntary Emissions Service Campaign to update the software programming on your vehicle's Engine Control Module. Kia has become aware that certain 2017-2018 MY Forte vehicles equipped with the 2.0L Multi-Port Injection (MPI) engine may have had a software update that turned off certain fuel system monitoring functions.

Managers that Kia America, Inc is conducting a Voluntary Emissions Service Campaign to update the software programming on the Engine Control Module on certain 2017-2018 MY Forte vehicles equipped with the 2.0L Multi-Port Injection (MPI) engines. While this issue has no effect on the drivability of the vehicle, nor does it release any air pollutants, the vehicle may fail a SMOG check and/or may not illuminate the Malfunction Indicator Light (MIL) for certain fuel system failures.

is conducting a Voluntary Emissions Service Campaign to update the software programming on the Engine Control Module on certain 2017-2018 MY Forte vehicles equipped with the 2.0L Multi-Port Injection (MPI) engines. While this issue has no effect on the drivability of the vehicle, nor does it release any air pollutants, the vehicle may fail a SMOG check and/or may not illuminate the Malfunction Indicator Light (MIL) for certain fuel system failures.

the small bearing of the Column Motor Driven Power Steering (C-MDPS) unit on the vehicles listed below, which may exhibit an abnormal noise when steering left and right. This may be caused by foreign substances in the MDPS worm shaft small bearing. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Small Bearing and does not affect the steering effort.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS), in order to protect the engine from excessive connecting rod bearing damage. This update is for certain 2017-2018MY Forte (YD/YDm) vehicles equipped with Nu 2.0L GDI engines, produced from May 19, 2016 through May 7, 2018.

conducting a Product Improvement Campaign to perform a software update on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter Nu GDI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU") (PI2106).

Parts and Service Managers that Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter Nu GDI engines, manufactured from May 19, 2016 through May 7, 2018.

Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter Nu GDI engines, manufactured from May 19, 2016 through May 7, 2018.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

P219E00, P219F00 - This bulletin provides the procedure to improve the logic of the Engine Control Module (ECM) on some 2017-2018MY Forte (YDm) vehicles, produced from May 15, 2016 through July 27, 2018, which may experience a malfunction indicator lamp (MIL) ON with DTC P0300, P0301, P0302, P0303, P0304 and/or P219C00. P219D00, P219E00, P219F00.

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

P219D00, P219E00, P219F00 - This bulletin provides the procedure to improve the logic of the Engine Control Module (ECM) on some 2017-2018MY Forte (YDm) vehicles, produced from May 15, 2016 through July 27, 2018, which may experience a malfunction indicator lamp (MIL) ON with DTC P0300, P0301, P0302, P0303, P0304 and/or P219C00. P219D00, P219E00, P219F00.

This bulletin provides information related to extracting in use performance tracking emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.

provides the procedure to improve the logic of the Engine Control Module (ECM) on some 2017-2018MY Forte (YDm) vehicles, produced from May 15, 2016 through July 27, 2018, which may experience a malfunction indicator lamp (MIL) ON with DTC P0300, P0301, P0302, P0303, P0304 and/or P219C00. P219D00, P219E00, P219F00.

extracting "in use performance tracking" emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting.

This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.

inspection and installation of the steel sealing ball on: * 3.3L & 3.8L Lambda engines for 2007-2008MY Sorento (BL), * 2.0L Nu engines for 2010-2019MY Soul (AM, PS), and * 1.8L & 2.0L Nu engines for 2010-2018MY Forte (TD, YD/YDm), 2019MY~ Forte (BDm). When replacing the cylinder heads on these engines, inspect the lubrication ports for installation of the steel sealing balls. Current replacement cylinder heads may not be equipped with the required steel balls. Identify and locate the nine (9) lubricant passages on 3.3L and 3.8L engines and three (3) on 1.8L and 2.0L engines and verify a steel ball is installed in each.

This bulletin provides the procedure to reset adaptive values on some 2017-2018MY Forte (YDm) 2.0L MPI vehicles, produced from May 15, 2016 through June 22, 2018, which may experience a malfunction indicator lamp illumination with DTC P0016 due to a stuck intake CVVT assembly. To correct this concern, reset the adaptive values of the engine ECU using the KDS as described in this bulletin.

This bulletin provides information related to extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.

regarding data transfer of automatic transmission (A/T) characteristic values on 2015MY-2018MY K900 (KH) vehicles equipped with A8TR1 8-speed A/T and 2017MY~ Sportage (QL), Forte (YDm), and Cadenza (YG) vehicles equipped with the GEN2 Type (A6MF2-2 6-speed / A8LF1 8-speed) A/T. The type of solenoid valve used to control gear shifts changed from indirect to direct control type to reduce oil capacity and improve fuel efficiency.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

New/revised sections of this pitstop are indicated by a black bar in the margin area. This Pitstop provides information regarding a possible mismatch of a SRSCM (Supplemental Restraint System Control Module) and driver seat belt buckle that may set the SRS DTC(s) B168400 and/or B176200 on the models listed below. When diagnosing a vehicle that has been in an accident and/or has recently had a superseded SRSCM replaced, it may be necessary to inspect and replace the driver seat belt buckle with the latest production P/N listed in EPC. Older production driver seat belt buckles have a 4 pin connector and may no longer be compatible with the superseded SRSCM. Only the SRSCM is superseded; the driver seat belt buckle is not superseded.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding A/C Compressor Field Coil Assembly inspection and replacement on some 2017-2018MY Forte (YDm) and 2019-2023MY Forte (BDm) vehicles.

alignment on 2014MY and later vehicles that may exhibit a warning light ON related to radar sensor alignment errors in the Forward Collision-Avoidance Assist (FCA)/Smart Cruise Control (SCC) system.

provides information regarding A/C Compressor Field Coil Assembly inspection and replacement on some 2017-2020 Forte (YDm, BDm) vehicles. Follow the diagnostic procedures in this bulletin to isolate air conditioning compressor faults such as open field coil circuit. Kia has made the Field Coil/Bolt available as serviceable item.

P0301, P0302, P0303, AND/OR P0304 (SA321) - This bulletin provides the procedure to replace all four (4) ignition coils or replace all four (4) coil radio frequency interference (RFI) springs on some 2017-2018MY Forte (YDm) 2.0L MPI vehicles, produced from May 16, 2016 through September 7, 2017, which may experience a malfunction indicator lamp illumination (MIL) ON with DTC P030X (P0300, P0301, P0302, P0303, or P0304).

(Supplemental Restraint System Control Module) and driver seat belt buckle that may set the SRS DTC(s) B168400 and/or B176200 on the models listed below. When diagnosing a vehicle that has been in an accident and/or has recently had a superseded SRSCM replaced, it may be necessary to inspect and replace the driver seat belt buckle with the latest production P/N listed in EPC. Older production driver seat belt buckles have a 4 pin connector and may no longer be compatible with the superseded SRSCM. Only the SRSCM is superseded; the driver seat belt buckle is not superseded. DTC B176200:

the electronic Dealer / Customer Mode Switch setting on the new Forte (BDm).

on some 2018MY Forte (YDm), produced from November 21, 2017 through April 12, 2018, and 2018MY Rio (SC) vehicles, both produced from November 22, 2017 through February 6, 2018, which may exhibit a malfunction indicator lamp (MIL) ON with DTCs P0300 through P0304 due to the spark plug porcelain cracking during manufacturing. Follow the procedure outlined in this bulletin to replace all four spark plugs, whether or not the MIL is ON.

procedure to replace all four (4) ignition coils or replace all four (4) coil radio frequency interference (RFI) springs on some 2017-2018MY Forte (YDm) 2.0L MPI vehicles, produced from May 16, 2017 through September 7, 2017, which may experience a malfunction indicator lamp illumination (MIL) ON with DTC P030X (P0300, P0301, P0302, P0303, or P0304).

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to apply additional anti-corrosion material to the underbody components on certain 2012-2017MY Rio (UB) and 2017-2018MY Forte (YD/YDm) vehicles produced within the date ranges shown below and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Corrosion can occur due to a combination of environmental conditions and lack of proper underbody maintenance, especially on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle.

information to apply additional anti-corrosion material to the underbody components on certain 2012-2017MY Rio (UB) and 2017-2018MY Forte (YD/YDm) vehicles produced within the date ranges shown below and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Corrosion can occur due to a combination of environmental conditions and lack of proper underbody maintenance, especially on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle.

a Voluntary Service Campaign, as a preventive measure, to apply anti-corrosion material to the underbody components of certain 2017-2018 MY Forte vehicles manufactured from January 9, 2016 through July 27, 2018 and 2012-2017 MY Rio vehicles manufactured from June 21, 2011 through March 31, 2017 that were originally sold in or are currently registered in one of the 28 states with high road salt usage.

Parts and Service Managers that Kia is conducting a Voluntary Service Campaign, as a preventive measure, to apply anti-corrosion material to the underbody components of certain 2017-2018 MY Forte vehicles manufactured from January 9, 2016 through July 27, 2018 and 2012-2017 MY Rio vehicles manufactured from June 21, 2011 through March 31, 2017 that were originally sold in or are currently registered in one of the 28 states with high road salt usage.

is conducting a Voluntary Service Campaign, as a preventive measure, to apply anti-corrosion material to the underbody components of certain 2017-2018 MY Forte vehicles manufactured from January 9, 2016 through July 27, 2018 and 2012-2017 MY Rio vehicles manufactured from June 21, 2011 through March 31, 2017 that were originally sold in or are currently registered in one of the 28 states with high road salt usage.

New/revised sections of this bulletin are indicated by a black bar in the margin area. When servicing windshield wipers on the below listed vehicles, including during PDI, ensure to raise the wiper arms to a vertical position to avoid damaging the paint on the rear edge of the hood.

certain Forte, Rio and Optima vehicles, which may exhibit a difficult-to-close/latch concern with the trunk lid.

noise heard from the rear of the vehicle when closing a door or trunk on some 2016MY-2018MY vehicles.

antenna pole in all 2018MY Forte (YDm) 5 Door SX and all 2018MY Rio (SC) vehicles at delivery to dealers and Transportation claims related to the antenna pole.

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace Dual Clutch Assembly and upgrade the TCU on some 2016-2020MY Kia vehicles listed in the table below, equipped with the 7 Speed Dual Clutch Transmission (DCT), which might exhibit clutch judder when accelerating from a stop.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

Unit (TCU) on 2017-2018MY Soul (PS) and Forte (YDm) and 2016-2018MY Optima (JFa) vehicles equipped with 1.6T GDI that have one of the following three components replaced: Dual Clutch Transmission (DCT) assembly; Transmission Control Unit (TCU), and Double Clutch Set.The friction material of the double clutch set has been changed and a TCU logic optimization must be performed in order to prevent initial shift shock.

This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.

frequently asked questions regarding the Voluntary Service Campaign (SC264).

New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information on setting the "Service Interval Reminder" feature available on most 2014-2023MY Kia vehicles (refer to model list on page 2). If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance. Refer to TSB ENG241 for 2023MY~ vehicles equipped with the Oil Life Management System (OLMS) feature not included in table on page 2.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace the sub frame on some 2018MY Forte (YD), produced from August 31, 2017 through September 4, 2017, and some 2018MY Forte (YDm) vehicles, produced from October 10, 2017 through October 23, 2017, which may experience a squeak noise at the sub frame area when driving.

frequently asked questions regarding the Product Improvement Campaign (PI2106).

Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.

for mileage setting on the listed vehicles with newly replaced instrument clusters.

some 2018MY Forte (YD), produced from August 31, 2017 through September 4, 2017, and some 2018MY Forte (YDm) vehicles, produced from October 10, 2017 through October 23, 2017, which may experience a squeak noise at the sub frame area when driving.

questions regarding the Voluntary Emissions Service Campaign (SC203).

revised to include additional information. This bulletin provides the procedure to improve the fuel filler door opening mechanism on some 2017-2018MY Forte (YDm) vehicles produced from May 23, 2016 through February 2, 2018 which may exhibit a fuel filler door that does not pop open and/or does not open far enough. Before conducting the procedure, verify that the vehicle is included in the list of affected VINs. For vehicles not on the Affected Vehicles list, but still experiencing the issue described above, perform the procedure outlined in this bulletin.

procedure to improve the fuel filler door opening mechanism on some 2017-2018MY Forte (YDm) vehicles produced from May 23, 2016 through February 2, 2018 which may exhibit a fuel filler door that does not pop open and/or does not open far enough. Before conducting the procedure, verify that the vehicle is included in the list of affected VINs.

regarding the instantaneous fuel mileage not displayed in the fuel economy menu of the trip computer in Type A instrument clusters on some 2014-2018MY Forte (YD) and 2017-2018MY Forte (YDm) vehicles. In some cases, an inadvertent press of the RESET (A) button may toggle the instantaneous MPG display off in the center display.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This pitstop provides the KDS service procedure for mileage setting on the models listed below with newly replaced instrument clusters. Certain models allow for mileage setting with the KDS, which prevents the need to send out the instrument cluster to a 3rd party for mileage adjustment (refer to PS264). After a new cluster is installed, cluster (variant) coding may also need to be conducted using the KDS. Make sure the KDS software is also updated to the latest version. Mileage setting should be performed by using the KDS only, as described in this bulletin.

regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.

fading/discoloring (yellowing) of the Quick Start Guide (QSG) installed prior to delivery to your dealer. In the event you encounter this issue, a replacement QSG can be ordered and shipped to your dealer in maximum quantities of five (5) per order, at no charge. Overnight shipping is available at an additional charge to the dealer. When placing your order, reference the part number (A) listed on the back of QSG.

the clock on UVO eServices (UVO 3.0) head units installed on 2017-2018MY vehicles.

vehicles; the differences in pairing instructions if it is the 1st phone or a 2nd phone that needs to be paired; and how to diagnose and troubleshoot customer Bluetooth complaints.:

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

replace the clock spring assembly on some 2014-2018MY Forte (YD/YDm) vehicles, produced from February 20, 2013 through June 30, 2018, which may experience intermittent malfunctioning steering wheel audio controls due to a clock spring connector pin deformation, with no related DTCs for this concern. Note: this does not impair the clock spring airbag function. Follow the procedure in this bulletin to inspect the clock spring female connector and, if necessary, replace the clock spring assembly.

conditioning system on certain 2019MY Niro Hybrid (DE HEV) and Niro Plug-in Hybrid (DE PHEV) vehicles, produced from July 9, 2018 through December 21, 2018, which may experience poor air conditioning performance due to a possible overfill of refrigerant. Follow the procedure in this bulletin to recover and recharge the air conditioning system with the proper amount. Kia is requesting the completion of this Service Action on all affected vehicles including dealer stock, prior to delivery.