2017 Kia Forte TSBs

(CS2312) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 20, which may not have been equipped with an immobilizer and whole Integrated Body control Unit (IBU) / Body Control Module (BCM) did receive the Ant-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)

(CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

Kia is conducting a Product Improvement Campaign to perform a software update on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter Nu GDI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (ECU).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

Kia is conducting an important Product Improvement Campaign to perform a software update on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter Nu GDI engines to protect the engine from excessive connecting rod bearing damage.

DTC P1326 (PI2106Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published (PI2106) titled Nu 2.0L GDI - Knock Sensor Detection System ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

Kia is conducting a Product Improvement Campaign to perform a software update on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

related to the Technical Service Bulletin previously published (PI2106) titled Nu 2.0L GDI - Knock Sensor Detection System ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

procedure to improve the logic of the Engine Control Module (ECM) on some 2017-2018MY Forte (YDm) vehicles equipped with the NU 2.0L MPI engine, produced from May 27, 2016 through June 27, 2018. While this issue has no effect on the drivability of the vehicle, nor does it release any air pollutants, the vehicle may fail a SMOG check and/or may not illuminate the Malfunction Indicator Light (MIL) for certain fuel system failures. In order to improve On-Board Diagnostics (OBD) logic, apply the improved software logic to the Engine system using the KDS ECU Upgrade function as described in this bulletin.

is conducting a Voluntary Emissions Service Campaign to update the software programming on your vehicle's Engine Control Module. Kia has become aware that certain 2017-2018 MY Forte vehicles equipped with the 2.0L Multi-Port Injection (MPI) engine may have had a software update that turned off certain fuel system monitoring functions.

Managers that Kia America, Inc is conducting a Voluntary Emissions Service Campaign to update the software programming on the Engine Control Module on certain 2017-2018 MY Forte vehicles equipped with the 2.0L Multi-Port Injection (MPI) engines. While this issue has no effect on the drivability of the vehicle, nor does it release any air pollutants, the vehicle may fail a SMOG check and/or may not illuminate the Malfunction Indicator Light (MIL) for certain fuel system failures.

is conducting a Voluntary Emissions Service Campaign to update the software programming on the Engine Control Module on certain 2017-2018 MY Forte vehicles equipped with the 2.0L Multi-Port Injection (MPI) engines. While this issue has no effect on the drivability of the vehicle, nor does it release any air pollutants, the vehicle may fail a SMOG check and/or may not illuminate the Malfunction Indicator Light (MIL) for certain fuel system failures.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS), in order to protect the engine from excessive connecting rod bearing damage. This update is for certain 2017-2018MY Forte (YD/YDm) vehicles equipped with Nu 2.0L GDI engines, produced from May 19, 2016 through May 7, 2018.

conducting a Product Improvement Campaign to perform a software update on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter Nu GDI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU") (PI2106).

Parts and Service Managers that Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter Nu GDI engines, manufactured from May 19, 2016 through May 7, 2018.

Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2017-2018 MY Kia Forte vehicles equipped with 2.0-liter Nu GDI engines, manufactured from May 19, 2016 through May 7, 2018.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

P219E00, P219F00 - This bulletin provides the procedure to improve the logic of the Engine Control Module (ECM) on some 2017-2018MY Forte (YDm) vehicles, produced from May 15, 2016 through July 27, 2018, which may experience a malfunction indicator lamp (MIL) ON with DTC P0300, P0301, P0302, P0303, P0304 and/or P219C00. P219D00, P219E00, P219F00.

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

P219D00, P219E00, P219F00 - This bulletin provides the procedure to improve the logic of the Engine Control Module (ECM) on some 2017-2018MY Forte (YDm) vehicles, produced from May 15, 2016 through July 27, 2018, which may experience a malfunction indicator lamp (MIL) ON with DTC P0300, P0301, P0302, P0303, P0304 and/or P219C00. P219D00, P219E00, P219F00.

provides the procedure to improve the logic of the Engine Control Module (ECM) on some 2017-2018MY Forte (YDm) vehicles, produced from May 15, 2016 through July 27, 2018, which may experience a malfunction indicator lamp (MIL) ON with DTC P0300, P0301, P0302, P0303, P0304 and/or P219C00. P219D00, P219E00, P219F00.

This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.

inspection and installation of the steel sealing ball on: * 3.3L & 3.8L Lambda engines for 2007-2008MY Sorento (BL), * 2.0L Nu engines for 2010-2019MY Soul (AM, PS), and * 1.8L & 2.0L Nu engines for 2010-2018MY Forte (TD, YD/YDm), 2019MY~ Forte (BDm). When replacing the cylinder heads on these engines, inspect the lubrication ports for installation of the steel sealing balls. Current replacement cylinder heads may not be equipped with the required steel balls. Identify and locate the nine (9) lubricant passages on 3.3L and 3.8L engines and three (3) on 1.8L and 2.0L engines and verify a steel ball is installed in each.

This bulletin provides the procedure to reset adaptive values on some 2017-2018MY Forte (YDm) 2.0L MPI vehicles, produced from May 15, 2016 through June 22, 2018, which may experience a malfunction indicator lamp illumination with DTC P0016 due to a stuck intake CVVT assembly. To correct this concern, reset the adaptive values of the engine ECU using the KDS as described in this bulletin.

and if necessary, replace the Air Drain Case on some 2014-18MY Soul (PS), produced from July 21, 2013 through June 1, 2017, some 2012-2017MY Rio (UB), produced from June 21, 2011 through March 31, 2017, some 2014-2017MY Forte (YD) vehicles, produced from February 18, 2013 through March 2, 2017, and some 2017MY Forte (YDm) vehicles, produced from May 16, 2016 through March 6, 2017, which may experience an early shut-off during fuel refill and/or a malfunction indicator lamp (MIL) illumination with DTC(s) P0449 or P0451.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

regarding data transfer of automatic transmission (A/T) characteristic values on 2015MY-2018MY K900 (KH) vehicles equipped with A8TR1 8-speed A/T and 2017MY~ Sportage (QL), Forte (YDm), and Cadenza (YG) vehicles equipped with the GEN2 Type (A6MF2-2 6-speed / A8LF1 8-speed) A/T. The type of solenoid valve used to control gear shifts changed from indirect to direct control type to reduce oil capacity and improve fuel efficiency.

related to extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California.

(YDm) 2.0L MPI vehicles, produced from May 15, 2016 through April 26, 2017, which may experience a malfunction indicator lamp illumination with DTC P0016 due to a stuck intake CVVT assembly. To correct this concern, reset the adaptive values of the engine ECU using the KDS as described in this bulletin.

of the Electronic Control Unit (ECU) on some 2017MY Forte (YDm) vehicles equipped with 2.0L MPI engine, produced from May 30, 2016 to February 22, 2017, which may experience a malfunction indicator lamp illumination with DTC P0300, P0301, P0302, P0303, or P0304. To correct this concern, apply the improved logic to the ECU using the KDS download as described in this bulletin.

extracting ?in use performance tracking? emissions data from the Engine Control Unit (ECU) of certain vehicles sold in California. The California Air Resources Board (CARB) requires the emissions data from vehicles with a minimum of 3,000 accumulated miles without reprogramming or resetting. To facilitate collection of this data at the dealer level, KDS screenshots will allow the capture of relevant parameters.

7-speed Dual Clutch Transmission (DCT), except the 2017MY~ Niro (DE) with a 1.6L Atkinson engine comes equipped with a 6-speed Dual Clutch Transmission (DCT). This automatic transmission is unlike the conventional automatic transmission found in the complete line up of Kia vehicles. The new DCT improves fuel efficiency and can also provide a sportier feel. Certain aspects of this technology may lead to customer concerns if they are unfamiliar with it. To help maximize owner satisfaction on this new technology, Kia would like all dealership sales and service personnel to be familiar with the characteristics of this new transmission.

of the Electronic Control Unit (ECU) on some 2017MY Forte (YDm) vehicles equipped with 2.0L MPI engine, produced from May 30, 2016 to February 22, 2017, which may experience a malfunction indicator lamp illumination with DTC P0300, P0301, P0302, P0303, or P0304. To correct this concern, apply the improved logic to the ECU using the KDS download as described in this bulletin. For confirmation that the latest reflash has been applied to a vehicle you are working on, verify the ROM ID using the table on page 2 of this bulletin. Before conducting the procedure, verify that the vehicle is included in the list of affected VINs.

CONCERN OF A MALFUNCTION INDICATOR LIGHT (MIL) ON IN THE DASH ON SOME 2017MY FORTE (YDM) WITH A 2.0L NU MPI ENGINE, CHECK FOR THE PRESENCE OF DTC P0014 EXHAUST CAMSHAFT POSITION TIMING OVER-ADVANCED OR SYSTEM PERFORMANCE. TO ADDRESS THE CONCERN OF MIL ON WITH P0014 ACTIVE, FOLLOW THE PROCEDURE OUTLINED BELOW.

SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace the inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP), and some 2016-2017MY Optima (JF) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed below. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace the inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP), and some 2016-2017MY Optima (JF) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed below. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace the inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP), and some 2016-2017MY Optima (JF) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed below. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to replace Dual Clutch Assembly and upgrade the TCU on some 2016-2020MY Kia vehicles listed in the table below, equipped with the 7 Speed Dual Clutch Transmission (DCT), which might exhibit clutch judder when accelerating from a stop.

the procedure to replace Dual Clutch Assembly and upgrade the TCU on some 2016-2020MY Kia vehicles listed on the table below, equipped with the 7 Speed Dual Clutch Transmission (DCT), which might exhibit clutch judder when accelerating from a stop. If the vehicle body vibrates without the steering wheel shuddering when performing creep driving test (driving the vehicle up to 3mph), the vehicle is exhibiting clutch judder. The creep test can be conducted by driving at a speed slower than 5 mph after releasing the brake.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

This bulletin provides the procedure to replace the inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP), and some 2016-2017MY Optima (JF) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed in this bulletin. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

Unit (TCU) on 2017-2018MY Soul (PS) and Forte (YDm) and 2016-2018MY Optima (JFa) vehicles equipped with 1.6T GDI that have one of the following three components replaced: Dual Clutch Transmission (DCT) assembly; Transmission Control Unit (TCU), and Double Clutch Set.The friction material of the double clutch set has been changed and a TCU logic optimization must be performed in order to prevent initial shift shock.

- This bulletin provides the procedure to replace the inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP), and some 2016-2017MY Optima (JF) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the following concerns: ? Malfunction Indicator Lamp (MIL) ON with DTC P0705 - Transmission Range Sensor (TRS) Circuit Malfunction (active or history) ? CAN-related DTCs (For both Hybrids: CAN DTC C2243); ? Intermittent no crank/no start ? Erratic or harsh shifting; ? EPB and Hold lights illuminated intermittently; ? ?Key OFF? indicated after placing the selector lever into the ?P? position and depressing the Start/Stop button.Note: When this condition occurs, the ?P? position is not indicated on the instrument cluster.

This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.

gear box yoke plug and assembly on some 2014-2017MY Forte (YD), produced from February 18, 2013 through November 15, 2016, and some 2017MY Forte (YDm) vehicles, produced from May 15, 2016 through February 9, 2017, which may exhibit a ticking noise while turning the steering wheel with the vehicle stopped or a rattle noise while driving.

inhibitor switch on some 2017MY Optima (JFa), Sorento (UMa), Optima Hybrid (HEV), Optima Plug-in Hybrid (PHEV), Sportage (QL), Forte (YD), and Sedona (YP) vehicles, equipped with a front wheel drive 6-speed transmission, which may experience the concerns listed below. These concerns may be due to the inhibitor switch not allowing the correct gear position signal to be sent to various control units.

Clutch Transmission (DCT) equipped on some 2017MY Forte (YDm) 5 Door 1.6T vehicles, produced from September 22, 2016 through November 11, 2016, which may experience hesitation/delayed shifting during acceleration.

The revisions include an updated Labor Op Code and a revised VIN list. This bulletin provides the procedure to upgrade the Base Audio Gen 3.0 Type A software on some 2017 Forte (YDm) vehicles, produced from May 16, 2016 to November 24, 2016, which may experience an intermittent power-on concern after vehicle ignition is switched on and an error message: ?Park the vehicle first to operate Bluetooth setting? while the gear shifter is in ?Park? position. Follow the procedure outlined in this bulletin to correct the concern. Before conducting the procedure, verify that the vehicle is included in the list of affected VINs.

upgrade the Base Audio Gen 3.0 Type A software on some 2017 Forte (YDm) vehicles, produced from May 16, 2016 to November 24, 2016, which may experience an intermittent power-on concern after vehicle ignition is switched on and an error message: ?Park the vehicle first to operate Bluetooth setting? while the gear shifter is in ?Park? position.

upgrade the Base Audio Gen 3.0 Type A software on some 2017 Forte (YDm) vehicles, produced from May 16, 2016 to November 24, 2016, which may experience an intermittent power-on concern after vehicle ignition is switched on and an error message: ?Park the vehicle first to operate Bluetooth setting? while the gear shifter is in ?Park? position. Follow the procedure outlined in this bulletin to correct the concern.

MANUAL TRANSMISSION DO NOT INCLUDE A TRUNK LINER ON THE UNDERSIDE OF TRUNK LID. IT IS IMPORTANT TO NOTE THAT THIS COMPONENT IS NOT LISTED IN THE BILL OF MATERIALS (BOM) AND IS NOT AVAILABLE ON THE MANUAL TRANSMISSION 4DR MODEL. INSTALLATION OF A TRUNK LINER WILL NOT BE COVERED BY KMA WARRANTY POLICY AND IS SUBJECT TO DEALER CHARGEBACK.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

New/revised sections of this pitstop are indicated by a black bar in the margin area. This Pitstop provides information regarding a possible mismatch of a SRSCM (Supplemental Restraint System Control Module) and driver seat belt buckle that may set the SRS DTC(s) B168400 and/or B176200 on the models listed below. When diagnosing a vehicle that has been in an accident and/or has recently had a superseded SRSCM replaced, it may be necessary to inspect and replace the driver seat belt buckle with the latest production P/N listed in EPC. Older production driver seat belt buckles have a 4 pin connector and may no longer be compatible with the superseded SRSCM. Only the SRSCM is superseded; the driver seat belt buckle is not superseded.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding A/C Compressor Field Coil Assembly inspection and replacement on some 2017-2018MY Forte (YDm) and 2019-2023MY Forte (BDm) vehicles.

alignment on 2014MY and later vehicles that may exhibit a warning light ON related to radar sensor alignment errors in the Forward Collision-Avoidance Assist (FCA)/Smart Cruise Control (SCC) system.

provides information regarding A/C Compressor Field Coil Assembly inspection and replacement on some 2017-2020 Forte (YDm, BDm) vehicles. Follow the diagnostic procedures in this bulletin to isolate air conditioning compressor faults such as open field coil circuit. Kia has made the Field Coil/Bolt available as serviceable item.

P0301, P0302, P0303, AND/OR P0304 (SA321) - This bulletin provides the procedure to replace all four (4) ignition coils or replace all four (4) coil radio frequency interference (RFI) springs on some 2017-2018MY Forte (YDm) 2.0L MPI vehicles, produced from May 16, 2016 through September 7, 2017, which may experience a malfunction indicator lamp illumination (MIL) ON with DTC P030X (P0300, P0301, P0302, P0303, or P0304).

(Supplemental Restraint System Control Module) and driver seat belt buckle that may set the SRS DTC(s) B168400 and/or B176200 on the models listed below. When diagnosing a vehicle that has been in an accident and/or has recently had a superseded SRSCM replaced, it may be necessary to inspect and replace the driver seat belt buckle with the latest production P/N listed in EPC. Older production driver seat belt buckles have a 4 pin connector and may no longer be compatible with the superseded SRSCM. Only the SRSCM is superseded; the driver seat belt buckle is not superseded. DTC B176200:

procedure to replace all four (4) ignition coils or replace all four (4) coil radio frequency interference (RFI) springs on some 2017-2018MY Forte (YDm) 2.0L MPI vehicles, produced from May 16, 2017 through September 7, 2017, which may experience a malfunction indicator lamp illumination (MIL) ON with DTC P030X (P0300, P0301, P0302, P0303, or P0304).

The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.

advising that Kia conducting Voluntary Service Campaign to inspect and, if necessary, replace brake line(s) in certain 2014-2017 MY Forte and Forte Koup vehicles that were originally sold in or are currently registered in states where heavy amounts of road salt are used. In addition, an anti-corrosion material will be applied to the underbody components for added protection.

MATERIAL REAPPLICATION (SC238A) - This bulletin provides information to inspect and, if necessary, replace the brake tube(s)/line(s) for leakage and apply additional anti-corrosion material to the underbody components on certain 2014-2017MY Forte and Forte Koup (YD) vehicles produced from November 7, 2012 through April 19, 2017, originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used, that previously had the cavity wax and anti-corrosion material application completed under SC238.

Kia is conducting a Voluntary Service Campaign to inspect and, if necessary, replace brake line(s) in certain 2014-2017 MY Forte and Forte Koup vehicles that were originally sold in or are currently registered in states where heavy amounts of road salt are used. In addition, an anti-corrosion material will be applied to the underbody components for added protection.

is conducting a Voluntary Service Campaign to inspect and, if necessary, replace brake line(s) in certain 2014-2017 MY Forte and Forte Koup vehicles that were originally sold in or are currently registered in states where heavy amounts of road salt are used. In addition, an anti-corrosion material will be applied to the underbody components for added protection.

APPLICATION (SC238) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect and, if necessary, replace the brake tube(s)/line(s) for leakage and also apply additional anti-corrosion material to the underbody components on certain 2014-2017MY Forte and Forte Koup (YD) vehicles produced from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Brake line corrosion can occur due to a combination of environment conditions and lack of proper underbody maintenance. Brake line corrosion can occur on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle. If this condition occurs, customers may experience low brake fluid level that can result in gradually increasing soft brake pedal feel and/or Brake Fluid Warning Light illumination.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect and, if necessary, replace the brake tube(s)/line(s) for leakage and also apply additional anti-corrosion material to the underbody components on certain 2014-2017MY Forte and Forte Koup (YD) vehicles produced from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Brake line corrosion can occur due to a combination of environment conditions and lack of proper underbody maintenance. Brake line corrosion can occur on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle. If this condition occurs, customers may experience low brake fluid level that can result in gradually increasing soft brake pedal feel and/or Brake Fluid Warning Light illumination.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect and, if necessary, replace the brake tube(s)/line(s) for leakage and also apply additional anti-corrosion material to the underbody components on certain 2014-2017MY Forte and Forte Koup (YD) vehicles produced from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Brake line corrosion can occur due to a combination of environment conditions and lack of proper underbody maintenance. Brake line corrosion can occur on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle. If this condition occurs, customers may experience low brake fluid level that can result in gradually increasing soft brake pedal feel and/or Brake Fluid Warning Light illumination.

bulletin provides information to inspect and, if necessary, replace the brake tube(s)/line(s) for leakage and also apply additional anti-corrosion material to the underbody components on certain 2014-2017MY Forte and Forte Koup (YD) vehicles produced from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Brake line corrosion can occur due to a combination of environment conditions and lack of proper underbody maintenance. Brake line corrosion can occur on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle. If this condition occurs, customers may experience low brake fluid level that can result in gradually increasing soft brake pedal feel and/or Brake Fluid Warning Light illumination.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

This bulletin provides the procedure to improve the logic of the Autonomous Emergency Brake (AEB) control unit on some 2016-2017MY Optima (JFa), and 2017MY Sorento (UMa), Forte (YDm), and Sedona (YP) vehicles, which may experience unexpected AEB activation in certain circumstances.

replace the outside rear combination lamp pads on some 2017MY Forte (YDm) vehicles, produced from May 23, 2016 to August 15, 2017, which may exhibit evidence of water intrusion in the outside rear combination lamps.

the outer rear combination lamp pads on some 2017MY Forte (YDm) vehicles, produced from May 24, 2016 to October 13, 2016, which may exhibit evidence of water intrusion in the outer rear combination lamps. Follow the procedure outlined in this bulletin to replace both left and right outer rear combination lamp pads. Before conducting the procedure, verify that the vehicle is included in the list of affected VINs.

with Autonomous Emergency Braking (AEB). Some customers may have interest and/or questions regarding this new technology, including what type of feedback they can expect from this system. The information provided below is a brief reference. The service information found on KGIS including the Owner?s Manual will provide more detailed information.

conducting a Voluntary Service Campaign on certain 2014-2017 MY Forte and Forte Koup vehicles manufactured at a Kia plant in Korea from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.

frequently asked questions regarding the Voluntary Service Campaign (SC264).

New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information on setting the "Service Interval Reminder" feature available on most 2014-2023MY Kia vehicles (refer to model list on page 2). If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance. Refer to TSB ENG241 for 2023MY~ vehicles equipped with the Oil Life Management System (OLMS) feature not included in table on page 2.

frequently asked questions regarding the Voluntary Service Campaign (SC238).

a Voluntary Service Campaign on certain 2014-2017 MY Forte and Forte Koup vehicles manufactured at a Kia plant in Korea from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.

Parts and Service Managers that Kia is conducting a Voluntary Service Campaign on certain 2014-2017 MY Forte and Forte Koup vehicles manufactured at a Kia plant in Korea from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.

is conducting a Voluntary Service Campaign on certain 2014-2017 MY Forte and Forte Koup vehicles manufactured at a Kia plant in Korea from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.

frequently asked questions regarding the Product Improvement Campaign (PI2106).

Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.

for mileage setting on the listed vehicles with newly replaced instrument clusters.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to apply additional anti-corrosion material to the underbody components on certain 2012-2017MY Rio (UB) and 2017-2018MY Forte (YD/YDm) vehicles produced within the date ranges shown below and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Corrosion can occur due to a combination of environmental conditions and lack of proper underbody maintenance, especially on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle.

information to apply additional anti-corrosion material to the underbody components on certain 2012-2017MY Rio (UB) and 2017-2018MY Forte (YD/YDm) vehicles produced within the date ranges shown below and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Corrosion can occur due to a combination of environmental conditions and lack of proper underbody maintenance, especially on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle.

a Voluntary Service Campaign, as a preventive measure, to apply anti-corrosion material to the underbody components of certain 2017-2018 MY Forte vehicles manufactured from January 9, 2016 through July 27, 2018 and 2012-2017 MY Rio vehicles manufactured from June 21, 2011 through March 31, 2017 that were originally sold in or are currently registered in one of the 28 states with high road salt usage.

Parts and Service Managers that Kia is conducting a Voluntary Service Campaign, as a preventive measure, to apply anti-corrosion material to the underbody components of certain 2017-2018 MY Forte vehicles manufactured from January 9, 2016 through July 27, 2018 and 2012-2017 MY Rio vehicles manufactured from June 21, 2011 through March 31, 2017 that were originally sold in or are currently registered in one of the 28 states with high road salt usage.

is conducting a Voluntary Service Campaign, as a preventive measure, to apply anti-corrosion material to the underbody components of certain 2017-2018 MY Forte vehicles manufactured from January 9, 2016 through July 27, 2018 and 2012-2017 MY Rio vehicles manufactured from June 21, 2011 through March 31, 2017 that were originally sold in or are currently registered in one of the 28 states with high road salt usage.

certain Forte, Rio and Optima vehicles, which may exhibit a difficult-to-close/latch concern with the trunk lid.

noise heard from the rear of the vehicle when closing a door or trunk on some 2016MY-2018MY vehicles.

installation on some 2017MY Forte (YD, YDm) 5-Door vehicles which may not have corresponding dimples for the insertion of the front license plate bracket guide pins.

rear door checkers on some 2017MY Forte (YDm) vehicles, produced from September 7, 2016 to October 6, 2016, which may experience a high effort to open or close the rear doors.

questions regarding the Voluntary Emissions Service Campaign (SC203).

revised to include additional information. This bulletin provides the procedure to improve the fuel filler door opening mechanism on some 2017-2018MY Forte (YDm) vehicles produced from May 23, 2016 through February 2, 2018 which may exhibit a fuel filler door that does not pop open and/or does not open far enough. Before conducting the procedure, verify that the vehicle is included in the list of affected VINs. For vehicles not on the Affected Vehicles list, but still experiencing the issue described above, perform the procedure outlined in this bulletin.

procedure to improve the fuel filler door opening mechanism on some 2017-2018MY Forte (YDm) vehicles produced from May 23, 2016 through February 2, 2018 which may exhibit a fuel filler door that does not pop open and/or does not open far enough. Before conducting the procedure, verify that the vehicle is included in the list of affected VINs.

This bulletin provides the procedure to replace the Air Drain Case on some 2014-2018MY Soul (PS), produced from July 21, 2013 through June 1, 2017, some 2012-2017MY Rio (UB), produced from June 21, 2011 through March 31, 2017, some 2014-2017MY Forte (YD), produced from February 18, 2013 through March 2, 2017, and some 2017MY Forte (YDm) vehicles, produced from May 16, 2016 through March 6, 2017, which may experience an early shut-off during fuel refill and/or a Malfunction Indicator Lamp (MIL) illumination with DTCs P0449 or P0451.

regarding the instantaneous fuel mileage not displayed in the fuel economy menu of the trip computer in Type A instrument clusters on some 2014-2018MY Forte (YD) and 2017-2018MY Forte (YDm) vehicles. In some cases, an inadvertent press of the RESET (A) button may toggle the instantaneous MPG display off in the center display.

models such as K900 (KH), Sedona (YP), Sorento (UMa), Optima (JFa), Sportage (QL), and 17MY Forte (YD, YDm), etc., equipped with a sunroof, a ventilation logic has been applied in order to prevent exhaust gases flowing into the vehicle due to the pressure difference (inside vs outside) that is generated when driving with the sunroof open. This logic allows the system to automatically switch from RECIRCULATION to FRESH mode when the sunroof is open.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This pitstop provides the KDS service procedure for mileage setting on the models listed below with newly replaced instrument clusters. Certain models allow for mileage setting with the KDS, which prevents the need to send out the instrument cluster to a 3rd party for mileage adjustment (refer to PS264). After a new cluster is installed, cluster (variant) coding may also need to be conducted using the KDS. Make sure the KDS software is also updated to the latest version. Mileage setting should be performed by using the KDS only, as described in this bulletin.

regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.

electric thermostat on 2017MY Forte (YDm) 2.0L MPI vehicles, produced from May 23, 2016 through March 15, 2017, which may exhibit a Malfunction Indicator Lamp (MIL) ON with DTC P0128.

fading/discoloring (yellowing) of the Quick Start Guide (QSG) installed prior to delivery to your dealer. In the event you encounter this issue, a replacement QSG can be ordered and shipped to your dealer in maximum quantities of five (5) per order, at no charge. Overnight shipping is available at an additional charge to the dealer. When placing your order, reference the part number (A) listed on the back of QSG.

the clock on UVO eServices (UVO 3.0) head units installed on 2017-2018MY vehicles.

upgrading the base audio system software of some 2017MY Forte (YDm) vehicles, produced from May 15, 2016 to August 12, 2016, to improve Bluetooth pairing.

upgrading the base audio system software of some 2017MY Forte (YDm) vehicles, produced from May 15, 2016 to August 12, 2016, to improve Bluetooth pairing.

AUDIO SYSTEM SOFTWARE TO INCLUDE ANDROID AUTO AND APPLE CARPLAY SOFTWARE.

and all Kia vehicles, after and including 2017MY, incorporate an anti-condensation logic to prevent the interior windows from becoming excessively fogged. The HVAC control head in these vehicles monitors ambient temperature to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature (about 60F or below), the anti-condensation logic may automatically set the air intake mode to FRESH, depending on the other HVAC settings. The anti-condensation logic is also designed to ensure that air intake mode is set to FRESH, as long as all conditions are met. If the user changes the air intake to RECIRCULATION, the anti-condensation logic will take control again after 5 minutes, and change the air intake mode back to FRESH. If this results in an undesired operation, the logic may be enabled or disabled by following the procedure below.

incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.

replace the clock spring assembly on some 2014-2018MY Forte (YD/YDm) vehicles, produced from February 20, 2013 through June 30, 2018, which may experience intermittent malfunctioning steering wheel audio controls due to a clock spring connector pin deformation, with no related DTCs for this concern. Note: this does not impair the clock spring airbag function. Follow the procedure in this bulletin to inspect the clock spring female connector and, if necessary, replace the clock spring assembly.

REFER TO TSB BOD181/SA327

software upgrade and mileage setting on 2015MY~ Sedona (YP), 2016MY~ Sorento (UMa), and 2017MY~ Forte (YD, YDm) vehicles with newly replaced instrument clusters.