2014 Kia Forte TSBs

advising that Kia is conducting Customer Satisfaction Campaign. Kia has developed a new zinc-reinforced ignition cylinder protector hardware upgrade and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Prior notifications stated that this modification had to be performed by July 1, 2025, but the subject vehicles are now eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 19, 2025 through December 31, 2025)

is conducting Customer Satisfaction Campaign. A software upgrade that addresses the social media theft method has been made available to owners of eligible Kia model vehicles free of charge at authorized Kia dealers since 2023. In addition to the anti-theft software, a new zinc-reinforced ignition cylinder protector hardware upgrade has been developed and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because the subject Kia vehicles were not factory-equipped with an engine immobilizer and were previously eligible for the software upgrade, these vehicles are eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 17, 2025 through February 27, 2026)

(CS2312) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 19, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) did receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the table on pages 9 and 10 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2024MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2002A, PI2002B and SC200**1) titled Knock Sensor Detection System - ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

an additional vehicle modification available for installation to help deter or thwart attempted thefts. This modification consists of a theft deterrent ignition cylinder protector and will be available to you free of charge for eighteen (18) months from the date of this letter.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

(CS2311) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 13, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2021MY vehicles (refer to the tables on pages 8-9 for applicable models and engine), which may exhibit a symptom of excessive oil consumption.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2002A, PI2002B and SC200**1) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information on diagnosing and/or repairing some 2011-2019MY vehicles (refer to table below for applicable model and engine), which may exhibit a symptom of excessive oil consumption.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in January 2021 (PI2002A and PI2002B, August 2020) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

2014-2016 MY Kia Forte vehicles equipped with the 2.0-liter GDI SULEV engine to update the catalyst heating logic in the Engine Control Module ("ECM") software programming, to ensure compliance with emissions regulations.

2014-2016 MY Kia Forte vehicles equipped with the 2.0-liter GDI SULEV engine to update the catalyst heating logic in the Engine Control Module ("ECM") with an improved version to ensure continued compliance with emissions regulations.

provides the procedure to update the Engine Control Module (ECM) software on some 2014-2016MY Forte (YD) Nu 2.0L GDI SULEV vehicles, produced from November 13, 2013 through March 17, 2016, to improve catalyst heating logic to ensure compliance with emissions regulations.

is conducting a Voluntary Emissions Service Campaign to update the software programming on the Engine Control Module. Kia has become aware that certain 2014-2016 MY Forte vehicles may have engine calibrations that were not optimized for emissions standards under certain specific conditions. These calibrations may cause the vehicle to release air pollutants which exceed Federal and California standards. These standards were established to protect your health and welfare from the dangers of air pollution.

certain 2014-2016 MY Kia Forte vehicles equipped with the 2.0-liter GDI SULEV engine, to update the catalyst heating logic of the Engine Control Module ("ECM") with an improved version.

flexible coupling in the MDPS motor of some vehicles which might experience a knock noise originating from the MDPS, when moving the steering wheel to right or left when the vehicle is stopped. This is caused by premature wear of the flexible coupling in the MDPS motor. If any knock noise from the MDPS occurs, replace the affected flexible coupling only with an improved one, following the Replacement Procedure below.

This bulletin provides information relating to all Kia vehicles equipped with Gasoline Direct Injection (GDI) engines. In these engines highly pressurized gasoline is injected via a common fuel rail and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional Multi-Point Fuel Injection (MPI) engine, the gasoline is injected into the intake port of each cylinder at a relatively low pressure. Due to high fuel pressure in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specifications for the GDI fuel system components.

inspection and installation of the steel sealing ball on: * 3.3L & 3.8L Lambda engines for 2007-2008MY Sorento (BL), * 2.0L Nu engines for 2010-2019MY Soul (AM, PS), and * 1.8L & 2.0L Nu engines for 2010-2018MY Forte (TD, YD/YDm), 2019MY~ Forte (BDm). When replacing the cylinder heads on these engines, inspect the lubrication ports for installation of the steel sealing balls. Current replacement cylinder heads may not be equipped with the required steel balls. Identify and locate the nine (9) lubricant passages on 3.3L and 3.8L engines and three (3) on 1.8L and 2.0L engines and verify a steel ball is installed in each.

and if necessary, replace the Air Drain Case on some 2014-18MY Soul (PS), produced from July 21, 2013 through June 1, 2017, some 2012-2017MY Rio (UB), produced from June 21, 2011 through March 31, 2017, some 2014-2017MY Forte (YD) vehicles, produced from February 18, 2013 through March 2, 2017, and some 2017MY Forte (YDm) vehicles, produced from May 16, 2016 through March 6, 2017, which may experience an early shut-off during fuel refill and/or a malfunction indicator lamp (MIL) illumination with DTC(s) P0449 or P0451.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

2014-2016 MY Kia Forte SULEV vehicles equipped with the 1.8L engine and designed to meet California emissions standards, to update the software programming for the Engine Control Module (?ECM?).

on certain 2014-2016 MY Kia Forte SULEV vehicles equipped with the 1.8L engine and designed to meet California emissions standards, to update the software programming for the Engine Control Module (?ECM?).

2014-2016 MY Kia Forte SULEV vehicles equipped with the 1.8L engine and designed to meet California emissions standards, to update the software programming for the Engine Control Module (?ECM?).

to replace the alternator pulley on some 2014-2016MY Forte (YD) vehicles with 1.8L and 2.0L Nu engines, produced from February 18, 2013 through July 18, 2016, which may experience an unusual engine vibration at idle that is sometimes more prevalent under certain electrical loads.

produced before July 14, 2014, may experience a hard to start concern or idle rpm fluctuations while stationary. If you encounter any of these concerns, check for white residue build up in the High Pressure Fuel Pump Inlet (see image below) which may cause a restriction and loss of fuel volume to the injectors.

replace both rear door power window motors on some 2014-15MY Forte (YD) vehicles, produced from February 1, 2013 through January 5, 2015, which may exhibit an inoperable rear door power window(s).

extracting ?in use performance tracking? emissions data from the engine control unit (ECU) in certain vehicles sold in California.

an ECM software upgrade for 2014MY Forte (YD) vehicles with 2.0L GDI engine, produced from January 31, 2013 to September 26, 2013, which may experience a malfunction indicator lamp (MIL) illuminated with the Electronic Control Module (ECM) system-related DTC P0461.

return lines.

extracting ?in use performance tracking? emissions data from the engine control unit (ECU) in certain vehicles sold in California.

flexible coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped. This condition may be caused by premature wear of the flexible coupling in the MDPS.

coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped.

system is the placement of each fuel injector directly into the engine cylinder head assembly. Therefore, it is completely normal for the combustion process to create deposits on the injector spray tip surfaces.

coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped. This condition may be caused by premature wear of the flexible coupling in the MDPS.

SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.

THE FLEXIBLE COUPLING IN THE MDPS MOTOR OF SOME VEHICLES WHICH MIGHT EXPERIENCE A KNOCK NOISE ORIGINATING FROM THE MDPS, WHEN MOVING THE STEERING WHEEL TO RIGHT OR LEFT WHEN THE VEHICLE IS STOPPED. THIS IS CAUSED BY PREMATURE WEAR OF THE FLEXIBLE COUPLING IN THE MDPS MOTOR. IF ANY KNOCK NOISE FROM THE MDPS OCCURS, REPLACE THE AFFECTED FLEXIBLE COUPLING ONLY WITH AN IMPROVED ONE, FOLLOWING THE REPLACEMENT PROCEDURE BELOW.

WHICH MONITORS AND PREVENTS THE SIMULTANEOUS ACTIVATION OF ACCELERATOR AND BRAKE PEDALS. WHEN ENGAGED, THE FEATURE REDUCES ENGINE POWER TO IDLE. MOST CUSTOMERS WILL NEVER NOTICE THE SMART PEDAL FEATURE WHEN ACTIVE, HOWEVER, CUSTOMERS WHO TEND TO REST THEIR FOOT ON THE BRAKE PEDAL WHILE DRIVING MIGHT DESCRIBE A HESITATION OR DELAY SYMPTOM AND NOT REALIZE THAT THE EMS ELECTRONIC CONTROL MODULE IS INTERVENING, AS DESIGNED.

FLEXIBLE COUPLING IN THE MDPS MOTOR OF SOME VEHICLES WHICH MIGHT EXPERIENCE A KNOCK NOISE ORIGINATING FROM THE MDPS, WHEN MOVING THE STEERING WHEEL TO RIGHT OR LEFT WHEN THE VEHICLE IS STOPPED. THIS IS CAUSED BY PREMATURE WEAR OF THE FLEXIBLE COUPLING IN THE MDPS MOTOR. IF ANY KNOCK NOISE FROM THE MDPS OCCURS, REPLACE THE AFFECTED FLEXIBLE COUPLING ONLY WITH AN IMPROVED ONE, FOLLOWING THE REPLACEMENT PROCEDURE BELOW.

SOME 2014-16MY FORTE (YD) VEHICLES WITH 1.8L AND 2.0L NU ENGINES MAY EXPERIENCE AN UNUSUAL ENGINE VIBRATION AT IDLE THAT IS SOMETIMES MORE PREVALENT UNDER CERTAIN ELECTRICAL LOADS. TO CORRECT THIS CONCERN, REPLACE THE EXISTING ALTERNATOR PULLEY WITH A NEW ONE FOLLOWING THE SERVICE PROCEDURE IN THIS BULLETIN.

PROPER ENGINE OIL GRADE / VISCOSITY TO BE USED WHEN SERVICING VEHICLES EQUIPPED WITH A TURBOCHARGER. IN ADDITION TO FOLLOWING THE TURBO-SPECIFIC MAINTENANCE INTERVAL SCHEDULES, IT IS VERY IMPORTANT TO FOLLOW THE GRADE AND THE SAE OIL VISCOSITY RECOMMENDATIONS IN THE APPLICABLE SERVICE MANUAL TO ENSURE THE PROPER LUBRICATION IS DELIVERED TO THE TURBOCHARGER AND TO PREVENT ENGINE DAMAGE.

REPLACE BOTH REAR DOOR POWER WINDOW MOTORS ON SOME 2014MY FORTE (YD) VEHICLES, PRODUCED FROM FEBRUARY 1, 2013 THROUGH SEPTEMBER 30, 2013, WHICH MAY EXHIBIT AN INOPERABLE REAR DOOR POWER WINDOW(S). KIA IS REQUESTING THE COMPLETION OF THIS SERVICE ACTION ON ALL AFFECTED VEHICLES. BEFORE CONDUCTING THE PROCEDURE, VERIFY THE VEHICLE IS INCLUDED IN THE LIST OF THE AFFECTED VINS.

MODEL ALL. NO YEARS LISTED. *PE

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure for upgrading the UVO system on some 2014~2016MY Soul (PS), Sorento (XMa), Optima (TF/QF), Forte (YD) and Sportage (SL) vehicles to address "Incoming ring volume too loud" complaints when using certain smartphones (non-iPhone). Additionally, in 2014MY vehicles the upgrade will also improve Bluetooth connectivity and voice recognition.

This bulletin provides information regarding correct 3.3 Volt and 8 Volt microphone (MIC) matching with head unit part numbers on some 2014-2015MY vehicles, in the event that the following concern occurs after a head unit replacement: * ?Bluetooth sound cannot be heard during a phone call by the person I am talking to (on the receiving end)? * ?Voice recognition is not working? * ?Voice commands are not picked up at all?

microphone (MIC) matching with head unit part numbers on some 2014-2015MY vehicles.

identify and record the head unit software level on various head unit platforms and generations.

(ELE091) (Rev 1) - This bulletin provides the procedure on how to identify and record the head unit software level on various head unit platforms and generations. This procedure will now be required when ordering head units through the Direct Exchange Program (see Parts Bulletin 91-961-0005).

2014MY Soul (PS), Sorento (XMa), Optima (TF, QF), Forte (YD), Sportage (SL), and Rio (UB) vehicles, to improve Bluetooth connectivity, Phonebook Download, Audio Streaming and Call History Download.

Sorento (XMa)/(UMa), Optima (TF HEV), Forte (YD), Sportage (SL), 2015-2016MY Sedona (YP), and 2014-2015(MY) Optima (QF/TF) vehicles to address ?Incoming ring volume too loud? complaints when using certain smartphones (non-iPhone). Additionally, in 2014MY vehicles the upgrade will also improve Bluetooth connectivity and Voice Recognition (VR).

part numbers, and compatible SD Card part numbers, for some Cadenza (VG), Sorento (XMa) and Forte (YD) vehicles.

ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.

BLUETOOTH CONCERNS WHEN USING AN IPHONE WITH IOS 8.X (IOS 8, 8.0.1, 8.0.2, 8.1, 8.1.2, 8.1.3, ETC.) WHILE PAIRED TO A HEAD UNIT.

(TF/QF), FORTE (YD) AND SPORTAGE (SL) VEHICLES TO IMPROVE BLUETOOTH CONNECTIVITY, VOICE RECOGNITION, AND TO IMPROVE "INCOMING RING VOLUME TOO LOUD" COMPLAINTS ON CERTAIN SMARTPHONES (NON-IPHONE).

(TF/QF), SORENTO (XMA), SPORTAGE (SL), RIO (UB), AND FORTE (YD) VEHICLES TO IMPROVE BLUETOOTH CONNECTIVITY, PHONEBOOK DOWNLOAD, AUDIO STREAMING, AND CALL HISTORY DOWNLOAD.

ERROR MESSAGES THAT MAY BE DISPLAYED ON THE NAVIGATION SCREEN WHEN THE INCORRECT SD CARD IS INSERTED. NOTE: ONLY NEW MODELS (DURING PDI INSPECTION OR AT THE POINT OF PURCHASE) OR COMPATIBILITY MISMATCHES THAT OCCUR AFTER HEAD UNIT REPLACEMENT WILL BE CONSIDERED FOR THIS PROGRAM.

THAT HAVE A SPECIFIC ERROR DISPLAYED ON THE NAVIGATION HEAD UNIT (SHOWN BELOW) AFTER PURCHASING AND INSTALLING A VERSION 8.5 MAP UPDATE SD CARD. A TOTAL OF 129 AFFECTED SD CARDS WERE PURCHASED BY CUSTOMERS THROUGH KIA DEALERS, FROM JANUARY 1ST TO MAY 11TH, 2015.

THE BASE AUDIO SYSTEM SOFTWARE OF SOME 2014MY SOUL (PS), OPTIMA (TF/QF), SORENTO (XMA), SPORTAGE (SL), RIO (UB), AND FORTE (YD) VEHICLES, TO IMPROVE BLUETOOTH CONNECTIVITY, PHONEBOOK DOWNLOAD, AUDIO STREAMING AND CALL HISTORY DOWNLOAD. FOR VEHICLES NOT ON THE AFFECTED VEHICLES LIST, BUT WITH A CUSTOMER CONCERN AS DESCRIBED ABOVE, PERFORM THE FOLLOWING PROCEDURE OUTLINED IN THIS BULLETIN AND SUBMIT A WARRANTY CLAIM PER ""CUSTOMER CONCERN"" (STANDARD TSB) CLAIM INFORMATION ON PAGE 11. "

RECORD THE HEAD UNIT SOFTWARE LEVEL ON VARIOUS HEAD UNIT PLATFORMS AND GENERATIONS. THIS PROCEDURE WILL NOW BE REQUIRED WHEN ORDERING HEAD UNITS THROUGH THE DIRECT EXCHANGE PROGRAM.

UVO SYSTEM ON SOME 2014~2016MY SOUL (PS), SORENTO (XMA)/(UMA), OPTIMA (TF HEV), FORTE (YD), SPORTAGE (SL) 2015~2016MY SEDONA (YP), AND 2014-2015(MY) OPTIMA (QT/TF) VEHICLES TO ADDRESS INCOMING RING VOLUME TOO LOUD COMPLAINTS WHEN USING CERTAIN SMARTPHONES (NON-IPHONE). ADDITIONALLY, IN 2014MY VEHICLES THE UPGRADE WILL ALSO IMPROVE BLUETOOTH CONNECTIVITY AND VOICE RECOGNITION (VR). FOR VEHICLES NOT ON THE AFFECTED VEHICLES LIST, BUT WITH A CUSTOMER CONCERN AS DESCRIBED ABOVE, PERFORM THE FOLLOWING PROCEDURE OUTLINED IN THIS BULLETIN AND SUBMIT A WARRANTY CLAIM PER "CUSTOMER CONCERN" (STANDARD TSB) CLAIM INFORMATION ON PAGE 10.

UVO SYSTEM ON SOME 2014~2016MY SOUL (PS), SORENTO (XMA), OPTIMA (TF/QF), FORTE (YD) AND SPORTAGE (SL) VEHICLES TO ADDRESS INCOMING RING VOLUME TOO LOUD COMPLAINTS WHEN USING CERTAIN SMARTPHONES (NON-IPHONE). ADDITIONALLY, IN 2014MY VEHICLES THE UPGRADE WILL ALSO IMPROVE BLUETOOTH CONNECTIVITY AND VOICE RECOGNITION. FOR VEHICLES NOT ON THE AFFECTED VEHICLES LIST, BUT WITH A CUSTOMER CONCERN AS DESCRIBED ABOVE, PERFORM THE FOLLOWING PROCEDURE OUTLINED IN THIS BULLETIN AND SUBMIT A WARRANTY CLAIM PER "CUSTOMER CONCERN" (STANDARD TSB) CLAIM INFORMATION ON PAGE 10.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked with the use of the key fob.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of the original letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to the vehicle to discourage a break-in.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 13, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation which activates when the vehicle is locked.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

developed a software upgrade that can be installed on the vehicle to restrict the operation of the vehicle's ignition system should a locked vehicle be the subject of a break-in and theft attempt without the key. This software upgrade will be available to the customer free of charge for eighteen (18) months from the date of this letter. When the software upgrade is complete, Kia will also provide the customer with window stickers that can be applied to your vehicle to discourage a break-in.

bulletin provides the procedure to upgrade the software logic of the Integrated Body Control Unit (IBU) or Body Control Module (BCM) system on certain 2014-2018MY Forte (YD), 2017-2018MY Forte (YDm), and 2019-2021MY Forte (BDm) vehicles produced within the dates outlined in page 10, which may not be equipped with an immobilizer. This logic upgrade will add anti-theft ignition start logic to the vehicle's system operation.

USB ports and 12V power outlets to connect/charge mobile phones. Customers may experience issues with their head units that may be related to the use of aftermarket USB charging cables, including; * Electrical interference and limited or no functionality when attempting to play music, or when charging a device through the USB port * Excessive static or noise when listening to the audio source * Malfunctions and screen freeze of the head unit screen * Slow down of the system response while device is plugged in * Music will not play from iPhone 5 or 6 with Kia iPod cable and aftermarket adapter * No or limited functionality when trying to play music from an Apple device

The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.

(YD) VEHICLES, PRODUCED FROM FEBRUARY 18, 2013 THROUGH MARCH 31, 2015, WHICH MAY EXHIBIT A TPMS LIGHT ILLUMINATED IN THE CLUSTER, ALONG WITH DTC C1212 VEHICLE SPEED SENSOR. TO CORRECT THIS CONCERN, REPLACE ALL FOUR (4) TPMS SENSORS WITH THE IMPROVED PARTS, BY FOLLOWING THE PROCEDURE OUTLINED IN THIS BULLETIN.

RELATED TO THE ECM SOFTWARE UPGRADE OF SOME 2014~2015MY FORTE (YD), PRODUCED FROM DECEMBER 7, 2013 TO APRIL 16, 2015, AND SOME 2014MY SPORTAGE (SL) VEHICLES, PRODUCED FROM APRIL 4, 2013 THROUGH JUNE 18, 2014, WHICH MAY EXHIBIT A MALFUNCTION INDICATOR LIGHT (MIL) ON WITH DTC C1212. TO APPLY THE IMPROVED LOGIC, THE ECM SHOULD BE REPROGRAMMED USING THE GDS/KDS DOWNLOAD, AS DESCRIBED IN THIS BULLETIN.

THIS SPECIAL SERVICE TOOL (SST) WAS DEVELOPED TO IMPROVE THE EFFICIENCY AND EFFECTIVENESS OF UPDATING 2010MY, AND LATER, KIA AUDIO HEAD UNITS USING A GDS, AND NOW, THE SAME FUNCTIONALITY IS AVAILABLE ON KDS. SOME TECHNICIANS MAY NOT BE AWARE OF THE BENEFITS THE AUM TOOL HAS TO OFFER. THE AUM ELIMINATES THE NEED FOR MULTIPLE USB FLASH DRIVES FOR SPECIFIC VEHICLE MODELS AND APPLICATIONS WHICH, IF MISAPPLIED, MAY RESULT IN AN IMPROPER AUDIO SYSTEM SOFTWARE UPDATE AND/OR LOCKED UP HEAD UNIT. ADDITIONALLY, FIELD REPORTS HAVE INDICATED THAT USB DRIVES FOR AUDIO UPDATES ARE EASILY LOST OR MISPLACED.

RELATED TO THE ECM SOFTWARE UPGRADE OF SOME 2014~2015MY FORTE (YD), PRODUCED FROM DECEMBER 7, 2013 TO APRIL 16, 2015, AND SOME 2014MY SPORTAGE (SL) VEHICLES, PRODUCED FROM APRIL 4, 2013 THROUGH JUNE 18, 2014, WHICH MAY EXHIBIT A MALFUNCTION INDICATOR LIGHT (MIL) ON WITH DTC C1212. TO APPLY THE IMPROVED LOGIC, THE ECM SHOULD BE REPROGRAMMED USING THE GDS/KDS DOWNLOAD, AS DESCRIBED IN THIS BULLETIN. FOR CONFIRMATION THAT THE LATEST REFLASH HAS BEEN DONE TO A VEHICLE YOU ARE WORKING ON, VERIFY ROM ID USING THE TABLES IN THIS TSB.

THIS CONDITION, THE ECM NEED TO BE REPROGRAMMED. MODEL 2015 FORTE. *PE

diagnosis of the Inhibitor Switch.

2014MY Sorento (XM), produced from January 22, 2013 through April 30, 2013, and 2014MY Forte (YD), produced from January 22, 2013 through July 16, 2013, which may exhibit a concern related to slow system start-up (boot-up time longer than 30 seconds).

*LJ

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.

gear box yoke plug and assembly on some 2014-2017MY Forte (YD), produced from February 18, 2013 through November 15, 2016, and some 2017MY Forte (YDm) vehicles, produced from May 15, 2016 through February 9, 2017, which may exhibit a ticking noise while turning the steering wheel with the vehicle stopped or a rattle noise while driving.

related to the Smart Key Systems on vehicles equipped with A/T (automatic transaxle) and Start/Stop Buttons (SSB).

Damper Clutch (D/C) Solenoid on 6-speed automatic transaxles with DTC P0741 (active or history), instead of replacing the transaxle. To reduce vehicle repair time, this procedure can be performed with the transaxle installed in the vehicle.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

RELEARN THE ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE ECM/PCM.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE PCM/TCM. AFTER THE ADAPTIVE VALUES ARE RESET, THE TRANSMISSION COMPUTER ADAPTIVE VALUES MUST BE RELEARNED BY DRIVING IN A PRECISE MANNER TO TEACH THE COMPUTER THE PROPER SOLENOID DUTY AND LINE PRESSURE FOR THE NEW TRANSMISSION/COMPUTER COMBINATION.

advising that Kia conducting Voluntary Service Campaign to inspect and, if necessary, replace brake line(s) in certain 2014-2017 MY Forte and Forte Koup vehicles that were originally sold in or are currently registered in states where heavy amounts of road salt are used. In addition, an anti-corrosion material will be applied to the underbody components for added protection.

MATERIAL REAPPLICATION (SC238A) - This bulletin provides information to inspect and, if necessary, replace the brake tube(s)/line(s) for leakage and apply additional anti-corrosion material to the underbody components on certain 2014-2017MY Forte and Forte Koup (YD) vehicles produced from November 7, 2012 through April 19, 2017, originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used, that previously had the cavity wax and anti-corrosion material application completed under SC238.

Kia is conducting a Voluntary Service Campaign to inspect and, if necessary, replace brake line(s) in certain 2014-2017 MY Forte and Forte Koup vehicles that were originally sold in or are currently registered in states where heavy amounts of road salt are used. In addition, an anti-corrosion material will be applied to the underbody components for added protection.

is conducting a Voluntary Service Campaign to inspect and, if necessary, replace brake line(s) in certain 2014-2017 MY Forte and Forte Koup vehicles that were originally sold in or are currently registered in states where heavy amounts of road salt are used. In addition, an anti-corrosion material will be applied to the underbody components for added protection.

APPLICATION (SC238) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect and, if necessary, replace the brake tube(s)/line(s) for leakage and also apply additional anti-corrosion material to the underbody components on certain 2014-2017MY Forte and Forte Koup (YD) vehicles produced from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Brake line corrosion can occur due to a combination of environment conditions and lack of proper underbody maintenance. Brake line corrosion can occur on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle. If this condition occurs, customers may experience low brake fluid level that can result in gradually increasing soft brake pedal feel and/or Brake Fluid Warning Light illumination.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect and, if necessary, replace the brake tube(s)/line(s) for leakage and also apply additional anti-corrosion material to the underbody components on certain 2014-2017MY Forte and Forte Koup (YD) vehicles produced from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Brake line corrosion can occur due to a combination of environment conditions and lack of proper underbody maintenance. Brake line corrosion can occur on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle. If this condition occurs, customers may experience low brake fluid level that can result in gradually increasing soft brake pedal feel and/or Brake Fluid Warning Light illumination.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to inspect and, if necessary, replace the brake tube(s)/line(s) for leakage and also apply additional anti-corrosion material to the underbody components on certain 2014-2017MY Forte and Forte Koup (YD) vehicles produced from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Brake line corrosion can occur due to a combination of environment conditions and lack of proper underbody maintenance. Brake line corrosion can occur on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle. If this condition occurs, customers may experience low brake fluid level that can result in gradually increasing soft brake pedal feel and/or Brake Fluid Warning Light illumination.

bulletin provides information to inspect and, if necessary, replace the brake tube(s)/line(s) for leakage and also apply additional anti-corrosion material to the underbody components on certain 2014-2017MY Forte and Forte Koup (YD) vehicles produced from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV. Brake line corrosion can occur due to a combination of environment conditions and lack of proper underbody maintenance. Brake line corrosion can occur on vehicles in states where heavy amounts of road salt are used if the materials used for ice/snow removal are not regularly flushed from the underbody of the vehicle. If this condition occurs, customers may experience low brake fluid level that can result in gradually increasing soft brake pedal feel and/or Brake Fluid Warning Light illumination.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

once fully attached, are utilized in various Kia models and are strictly intended for ?one time use.? Some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.? It is critical for technicians to be aware that ALL such locking fasteners, regardless of type, are for ?one time use? only.

strictly intended for ?one time use?. Though not limited to the following, some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.?

conducting a Voluntary Service Campaign on certain 2014-2017 MY Forte and Forte Koup vehicles manufactured at a Kia plant in Korea from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.

New/revised sections of this bulletin are indicated by a black bar in the margin area.This bulletin provides information on setting the "Service Interval Reminder" feature available on most 2014-2023MY Kia vehicles (refer to model list on page 2). If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance. Refer to TSB ENG241 for 2023MY~ vehicles equipped with the Oil Life Management System (OLMS) feature not included in table on page 2.

frequently asked questions regarding the Voluntary Service Campaign (SC238).

a Voluntary Service Campaign on certain 2014-2017 MY Forte and Forte Koup vehicles manufactured at a Kia plant in Korea from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.

Parts and Service Managers that Kia is conducting a Voluntary Service Campaign on certain 2014-2017 MY Forte and Forte Koup vehicles manufactured at a Kia plant in Korea from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.

is conducting a Voluntary Service Campaign on certain 2014-2017 MY Forte and Forte Koup vehicles manufactured at a Kia plant in Korea from November 7, 2012 through April 19, 2017 and originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used.

Forte Koup vehicle owners to use in the event they incurred expenses related to this Extended Warranty Program prior to the launch of the Warranty Extension.

Interval Reminder" feature available on most Kia vehicles. If the service interval reminder is set, the customer will be informed to have the next maintenance service performed, which can positively affect vehicle longevity and performance.

CAMERA OF SOME KIA VEHICLES (SEE TABLE ON PG. 6 FOR SPECIFIC MODELS AND PRODUCTION DATES) WHICH MAY EXHIBIT INADEQUATE IMAGE QUALITY FROM THE REAR VIEW CAMERA. DIAGNOSE THE CONCERNS USING THE INFORMATION IN THIS BULLETIN AND, IF NECESSARY, REPLACE THE REAR VIEW CAMERA WITH AN IMPROVED PART BY FOLLOWING THE APPLICABLE SERVICE PROCEDURE ON KGIS.

been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the replacement of the driver's airbag clock spring assembly on some 2012-2013MY Rio (UB) and 2014-2015MY Forte/Koup (YD) associated with the Warranty Extension Program (WTY017).

provides information related to the replacement of the drivers airbag clock spring assembly on some 2012-2013MY Rio (UB) and 2014-2015MY Forte/Koup (YD) associated with the Warranty Extension Program (WTY017). If the Airbag Warning Light is ON with any of the DTCs below, follow the procedure outlined in this bulletin to resolve the issue.

2014-2015 MY Kia Forte and Forte Koup vehicles of the warranty extension on the driver's front airbag clock spring assembly to fifteen (15) years with unlimited mileage, starting from the date the vehicles were first put into service.

(WTY017) on the driver's front airbag clock spring assembly to fifteen (15) years with unlimited mileage, starting from the date the vehicles were first put into service.

service managers of the warranty extension on the driver's front airbag clock spring assembly on 2012-2013 MY Rio and 2014-2015 MY Forte and Forte Koup vehicles to fifteen (15) years with unlimited mileage, starting from the date the vehicles were first put into service.

extension on the driver's front airbag clock spring assembly on 2012-2013 MY Rio and 2014-2015 MY Forte and Forte Koup vehicles to fifteen (15) years with unlimited mileage, starting from the date the vehicles were first put into service.

wheel hub bearing and both front castle nuts on some 2014MY Forte (YD) vehicles, produced from February 18, 2013 through February 5, 2014, which may experience abnormal noise from the front wheel hub bearing area while driving.

exhibit a clicking type noise from the front suspension when carrying a full load of passengers and turning the wheel in either direction at low speeds; such as in a parking lot situation or when pulling into steeply inclined driveway.

FROM THE FRONT SUSPENSION WHEN CARRYING A FULL LOAD OF PASSENGERS AND TURNING THE WHEEL IN EITHER DIRECTION AT LOW SPEEDS; SUCH AS IN A PARKING LOT SITUATION OR WHEN PULLING INTO STEEPLY INCLINED DRIVEWAY. TO CORRECT THIS CONDITION, PLACE THE VEHICLE ON THE LIFT, RAISE THE DUST COVER AND APPLY A GENEROUS AMOUNT OF SILICONE BASED LUBRICANT ONTO THE LEFT AND RIGHT STRUT CAPS, AS SHOWN BELOW.

This bulletin provides the procedure to replace the Air Drain Case on some 2014-2018MY Soul (PS), produced from July 21, 2013 through June 1, 2017, some 2012-2017MY Rio (UB), produced from June 21, 2011 through March 31, 2017, some 2014-2017MY Forte (YD), produced from February 18, 2013 through March 2, 2017, and some 2017MY Forte (YDm) vehicles, produced from May 16, 2016 through March 6, 2017, which may experience an early shut-off during fuel refill and/or a Malfunction Indicator Lamp (MIL) illumination with DTCs P0449 or P0451.

regarding the instantaneous fuel mileage not displayed in the fuel economy menu of the trip computer in Type A instrument clusters on some 2014-2018MY Forte (YD) and 2017-2018MY Forte (YDm) vehicles. In some cases, an inadvertent press of the RESET (A) button may toggle the instantaneous MPG display off in the center display.

illuminated with DTC(s) P0442, P0455, P0456, or P0457 (Evaporative Emissions System-Leak detected) and the evaporative (EVAP) leak self-test resulted in NTF, a manual EVAP test is recommended.

LENSES FOLLOWING A RAINSTORM OR AFTER WASHING THEIR VEHICLE. THESE WATER DROPLETS ARE MORE VISIBLE AT NIGHT AND THE QUANTITY OF WATER PRESENT IS MORE THAN JUST A THIN FILM OF CONDENSATION WHICH MAY NOT EASILY EVAPORATE. THIS CONCERN IS CAUSED BY A GAP BETWEEN THE TAIL LAMP HOUSING GASKET AND VEHICLE BODY WHICH ALLOWS WATER TO INFILTRATE INTO THE TAIL LAMP. TO RESOLVE THIS CONCERN, ORDER NEW FOAM GASKETS AND INSTALL THEM BETWEEN THE LEFT AND RIGHT TAIL LAMPS AS REQUIRED AND THE BODY OF THE VEHICLE, AS OUTLINED IN THE TSB.

COMPLAIN ABOUT WATER DROPLETS FORMING INSIDE THE REAR TAIL LAMP LENSES FOLLOWING A RAINSTORM OR AFTER WASHING THEIR VEHICLE. THESE WATER DROPLETS ARE MORE VISIBLE AT NIGHT AND THE QUANTITY OF WATER PRESENT IS MORE THAN JUST A THIN FILM OF CONDENSATION WHICH MAY NOT EASILY EVAPORATE. THIS CONCERN IS CAUSED BY A GAP BETWEEN THE TAIL LAMP HOUSING GASKET AND VEHICLE BODY WHICH ALLOWS WATER TO INFILTRATE INTO THE TAIL LAMP. TO RESOLVE THIS CONCERN, ORDER NEW FOAM GASKETS AND INSTALL THEM BETWEEN THE LEFT AND RIGHT TAIL LAMPS AS REQUIRED AND THE BODY OF THE VEHICLE.

showing that the recall has been completed.

2013 to August 27, 2013 and equipped with a Kia accessory spoiler, may exhibit a gap forming between the adhesive tape on the spoiler and the trunk lid. To inspect for and to correct this condition, follow the procedure outlined in this TSB.

MAY 21, 2014, CUSTOMERS MAY COMPLAIN OF WATER LEAKING INTO THE TRUNK AND/OR REAR FLOORBOARD AREA, AFTER A RAINSTORM OR A CARWASH. THIS CONDITION MAY BE CAUSED BY IMPROPER SEALING BETWEEN THE OUTER TAIL LAMP (A) GASKET AND THE BODY OF THE VEHICLE. TO RESOLVE THIS CONCERN, REPLACE THE EXISTING GASKETS WITH THE IMPROVED PARTS ON BOTH OUTER TAIL LAMP ASSEMBLIES.

STRIKER OF SOME 2014MY FORTE (YD) VEHICLES, PRODUCED FROM FEBRUARY 1, 2013 THROUGH FEBRUARY 28, 2014, WHICH MAY EXHIBIT A RATTLING NOISE FROM THE TRUNK AREA AND/OR DIFFICULTY WHEN CLOSING THE TRUNK. KIA IS REQUESTING THE COMPLETION OF THIS SERVICE ACTION ON ALL AFFECTED VEHICLES. BEFORE CONDUCTING THE PROCEDURE, VERIFY THE VEHICLE IS INCLUDED IN THE LIST OF THE AFFECTED VINS.

2014, MAY EXPERIENCE DIFFICULTY WHEN OPENING/CLOSING THE DOORS IN FREEZING TEMPERATURES, DUE TO THE OPERATION OF THE SHORT DROP FEATURE AS A RESULT OF FROST/ICE BUILD-UP BETWEEN THE WINDOW GLASS AND OUTSIDE BELT MOLDING.

now making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

replace the clock spring assembly on some 2014-2018MY Forte (YD/YDm) vehicles, produced from February 20, 2013 through June 30, 2018, which may experience intermittent malfunctioning steering wheel audio controls due to a clock spring connector pin deformation, with no related DTCs for this concern. Note: this does not impair the clock spring airbag function. Follow the procedure in this bulletin to inspect the clock spring female connector and, if necessary, replace the clock spring assembly.

regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.

traffic customer complaints, as detailed in this Article.

incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.

function using the GDS.

SOME 2014~2015MY SPORTAGE (SL), FORTE (YD), OPTIMA (TF/QF), OPTIMA HYBRID (TF HEV) AND SORENTO (XMA) VEHICLES, WHICH MAY EXHIBIT AN INOPERATIVE UVO MEDIA BUTTON.

SOME 2014~2015MY SPORTAGE (SL), FORTE (YD), OPTIMA (TF/QF), OPTIMA HYBRID (TF HEV) AND SORENTO (XMA) VEHICLES, WHICH MAY EXHIBIT AN INOPERATIVE UVO MEDIA BUTTON.