2013 Kia Forte TSBs

advising that Kia is conducting Customer Satisfaction Campaign. Kia has developed a new zinc-reinforced ignition cylinder protector hardware upgrade and can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Prior notifications stated that this modification had to be performed by July 1, 2025, but the subject vehicles are now eligible until March 31, 2027, to have the ignition cylinder protector installedif requestedat no cost through an authorized Kia dealership. (Mailing of these notifications to vehicle owners will be completed from December 19, 2025 through December 31, 2025)

This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2002A, PI2002B and SC200**1) titled Knock Sensor Detection System - ECU Logic Improvement. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

an additional vehicle modification available for installation to help deter or thwart attempted thefts. This modification consists of a theft deterrent ignition cylinder protector and will be available to you free of charge for eighteen (18) months from the date of this letter.

(CS2311) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 15, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

(CS2311) - This bulletin provides information to install a Theft Deterrent Ignition Cylinder Protector on certain 2010-2022MY Kia vehicles outlined on page 13, which may not have been equipped with an immobilizer and whose Integrated Body Control Unit (IBU) / Body Control Module (BCM) are not able to receive the Anti-Theft Software Logic upgrade under CS2301/02/03/04/05/06/07/08/09 TSBs. In an effort to help prevent thefts of Kia vehicles that are not equipped with an immobilizer, a protective cover will be permanently affixed to the ignition cylinder. This Theft Deterrent Ignition Cylinder Protector prevents the removal of the key lock cylinder thereby preventing access to the ignition tumbler.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2002A, PI2002B and SC200**1) titled "Knock Sensor Detection System - ECU Logic Improvement". Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

flexible coupling in the MDPS motor of some vehicles which might experience a knock noise originating from the MDPS, when moving the steering wheel to right or left when the vehicle is stopped. This is caused by premature wear of the flexible coupling in the MDPS motor. If any knock noise from the MDPS occurs, replace the affected flexible coupling only with an improved one, following the Replacement Procedure below.

inspection and installation of the steel sealing ball on: * 3.3L & 3.8L Lambda engines for 2007-2008MY Sorento (BL), * 2.0L Nu engines for 2010-2019MY Soul (AM, PS), and * 1.8L & 2.0L Nu engines for 2010-2018MY Forte (TD, YD/YDm), 2019MY~ Forte (BDm). When replacing the cylinder heads on these engines, inspect the lubrication ports for installation of the steel sealing balls. Current replacement cylinder heads may not be equipped with the required steel balls. Identify and locate the nine (9) lubricant passages on 3.3L and 3.8L engines and three (3) on 1.8L and 2.0L engines and verify a steel ball is installed in each.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.

will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.

flexible coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped. This condition may be caused by premature wear of the flexible coupling in the MDPS.

coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped.

coupling in the MDPS motor of some of vehicles, which may experience a ?clicking? noise emanating from the MDPS when turning the steering wheel left or right, while stopped. This condition may be caused by premature wear of the flexible coupling in the MDPS.

2013 KIA VEHICLE, KIA MOTORS AMERICA WOULD LIKE ALL DEALERSHIP SERVICE PERSONNEL TO BE FAMILIAR WITH THE MODEL TIPS OUTLINED HERE TO HELP MAXIMIZE OWNER SATISFACTION WITH CERTAIN FEATURES.

SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.

THE FLEXIBLE COUPLING IN THE MDPS MOTOR OF SOME VEHICLES WHICH MIGHT EXPERIENCE A KNOCK NOISE ORIGINATING FROM THE MDPS, WHEN MOVING THE STEERING WHEEL TO RIGHT OR LEFT WHEN THE VEHICLE IS STOPPED. THIS IS CAUSED BY PREMATURE WEAR OF THE FLEXIBLE COUPLING IN THE MDPS MOTOR. IF ANY KNOCK NOISE FROM THE MDPS OCCURS, REPLACE THE AFFECTED FLEXIBLE COUPLING ONLY WITH AN IMPROVED ONE, FOLLOWING THE REPLACEMENT PROCEDURE BELOW.

WHICH MONITORS AND PREVENTS THE SIMULTANEOUS ACTIVATION OF ACCELERATOR AND BRAKE PEDALS. WHEN ENGAGED, THE FEATURE REDUCES ENGINE POWER TO IDLE. MOST CUSTOMERS WILL NEVER NOTICE THE SMART PEDAL FEATURE WHEN ACTIVE, HOWEVER, CUSTOMERS WHO TEND TO REST THEIR FOOT ON THE BRAKE PEDAL WHILE DRIVING MIGHT DESCRIBE A HESITATION OR DELAY SYMPTOM AND NOT REALIZE THAT THE EMS ELECTRONIC CONTROL MODULE IS INTERVENING, AS DESIGNED.

FLEXIBLE COUPLING IN THE MDPS MOTOR OF SOME VEHICLES WHICH MIGHT EXPERIENCE A KNOCK NOISE ORIGINATING FROM THE MDPS, WHEN MOVING THE STEERING WHEEL TO RIGHT OR LEFT WHEN THE VEHICLE IS STOPPED. THIS IS CAUSED BY PREMATURE WEAR OF THE FLEXIBLE COUPLING IN THE MDPS MOTOR. IF ANY KNOCK NOISE FROM THE MDPS OCCURS, REPLACE THE AFFECTED FLEXIBLE COUPLING ONLY WITH AN IMPROVED ONE, FOLLOWING THE REPLACEMENT PROCEDURE BELOW.

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

This bulletin provides information regarding axle shaft serviceability for Kia vehicles equipped with a six-speed automatic transmission.

Damper Clutch (D/C) Solenoid on 6-speed automatic transaxles with DTC P0741 (active or history), instead of replacing the transaxle. To reduce vehicle repair time, this procedure can be performed with the transaxle installed in the vehicle.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

THIS BULLETIN PROVIDES INFORMATION REGARDING AXLE SHAFT SERVICEABILITY FOR KIA VEHICLES EQUIPPED WITH A SIX-SPEED AUTOMATIC TRANSMISSION. REFER TO THE TABLE BELOW FOR A DETAILED LIST OF VEHICLE MODELS. INDIVIDUAL SERVICE PARTS SUCH AS AXLE BOOTS, JOINTS AND HARDWARE FOR INNER JOINT ARE NOW AVAILABLE THROUGH YOUR PARTS DEPARTMENT.

RELEARN THE ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE ECM/PCM.

VARIOUS SHIFT SOLENOIDS ON 6-SPEED AUTOMATIC TRANSAXLES WITH DTCS P0741, P0743, P0748, P0753, P0758, P0763, P0768, P0773, P1778 AND P2709. REPLACE THE SOLENOIDS IF CURRENT OR HISTORY CODES ARE PRESENT; DO NOT REPLACE THE TRANSAXLE. TO REDUCE VEHICLE REPAIR TIME, THIS PROCEDURE CAN BE PERFORMED WITH THE TRANSAXLE INSTALLED IN THE VEHICLE. REFER TO KGIS FOR SOLENOID PACK REMOVAL AND REINSTALLATION PROCEDURES FOR THE SPECIFIC YEAR AND MODEL OF THE VEHICLE.

ADAPTIVE VALUES AFTER TRANSMISSION REPLACEMENT OR REPROGRAMMING/REPLACEMENT OF THE PCM/TCM. AFTER THE ADAPTIVE VALUES ARE RESET, THE TRANSMISSION COMPUTER ADAPTIVE VALUES MUST BE RELEARNED BY DRIVING IN A PRECISE MANNER TO TEACH THE COMPUTER THE PROPER SOLENOID DUTY AND LINE PRESSURE FOR THE NEW TRANSMISSION/COMPUTER COMBINATION.

diagnosis of the Inhibitor Switch.

USB ports and 12V power outlets to connect/charge mobile phones. Customers may experience issues with their head units that may be related to the use of aftermarket USB charging cables, including; * Electrical interference and limited or no functionality when attempting to play music, or when charging a device through the USB port * Excessive static or noise when listening to the audio source * Malfunctions and screen freeze of the head unit screen * Slow down of the system response while device is plugged in * Music will not play from iPhone 5 or 6 with Kia iPod cable and aftermarket adapter * No or limited functionality when trying to play music from an Apple device

The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.

FORTE VEHICLES NOT ACCEPTING THE VARIANT CODE LISTED ON KGIS, FOLLOWING REPLACEMENT OF THE AIR BAG CONTROL MODULE. IN SOME CASES, AN AIR BAG MODULE WITH A SUPERSEDED PART NUMBER MAY REQUIRE A DIFFERENT VARIANT CODE. KGIS IS BEING UPDATED IN PHASES AND WILL LIST BOTH VARIANT CODES (OLD AND NEW) IN CASE OF P/N SUPERSESSION.

THE CUSTOMER MAY STATE THAT THE VEHICLE WILL NOT FLASH THE HAZARD LIGHTS OR SOUND THE HORN WHEN LOCKING THE DOORS WITH THE TRANSMITTER. AS DESIGNED, THE VEHICLE SHOULD FLASH THE HAZARD LIGHTS AND SOUND THE HORN AFTER PRESSING THE LOCK BUTTON TWO (2) TIMES WITHIN FIVE (5) SECONDS. IF THIS CONCERN IS OCCURRING, VERIFY IF IT IS RELATED TO THE REMOTE START CONTROL MODULE BY CHECKING THE POSITION OF THE OVERHEAD INTERIOR LIGHT SWITCH. IF THE SWITCH IS IN THE OFF POSITION, MOVE THE SWITCH TO THE DOOR POSITION AND RETEST THE SYSTEM.

THIS SPECIAL SERVICE TOOL (SST) WAS DEVELOPED TO IMPROVE THE EFFICIENCY AND EFFECTIVENESS OF UPDATING 2010MY, AND LATER, KIA AUDIO HEAD UNITS USING A GDS, AND NOW, THE SAME FUNCTIONALITY IS AVAILABLE ON KDS. SOME TECHNICIANS MAY NOT BE AWARE OF THE BENEFITS THE AUM TOOL HAS TO OFFER. THE AUM ELIMINATES THE NEED FOR MULTIPLE USB FLASH DRIVES FOR SPECIFIC VEHICLE MODELS AND APPLICATIONS WHICH, IF MISAPPLIED, MAY RESULT IN AN IMPROPER AUDIO SYSTEM SOFTWARE UPDATE AND/OR LOCKED UP HEAD UNIT. ADDITIONALLY, FIELD REPORTS HAVE INDICATED THAT USB DRIVES FOR AUDIO UPDATES ARE EASILY LOST OR MISPLACED.

identify and record the head unit software level on various head unit platforms and generations.

(ELE091) (Rev 1) - This bulletin provides the procedure on how to identify and record the head unit software level on various head unit platforms and generations. This procedure will now be required when ordering head units through the Direct Exchange Program (see Parts Bulletin 91-961-0005).

BLUETOOTH CONCERNS WHEN USING AN IPHONE WITH IOS 8.X (IOS 8, 8.0.1, 8.0.2, 8.1, 8.1.2, 8.1.3, ETC.) WHILE PAIRED TO A HEAD UNIT.

RECORD THE HEAD UNIT SOFTWARE LEVEL ON VARIOUS HEAD UNIT PLATFORMS AND GENERATIONS. THIS PROCEDURE WILL NOW BE REQUIRED WHEN ORDERING HEAD UNITS THROUGH THE DIRECT EXCHANGE PROGRAM.

SYSTEM SOFTWARE OF SOME 2013MY SOUL (AM), OPTIMA (TF/QF), SORENTO (XMA) AND FORTE (TD) VEHICLES, TO IMPROVE BLUETOOTH CONNECTIVITY.

launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.

launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.

registered in the states where heavy amounts of road salt are used of a service campaign to add additional anti-corrosion material to underbody components of vehicle.

DEBRIS ACCUMULATION ON THE WINDSHIELD WASHER PUMP INLET FILTER. OVER TIME, SOME KIA VEHICLES MAY EXHIBIT A LIMITED APPLICATION OF WINDSHIELD WASHER FLUID WHEN THE WASHER FUNCTION IS USED. LIMITED APPLICATION OF WINDSHIELD WASHER FLUID CAN BE CAUSED BY FOREIGN DEBRIS ON THE WASHER PUMP INLET FILTER. TO CORRECT THIS CONDITION, REPLACE THE WASHER PUMP INLET FILTER AND PERFORM THE WINDSHIELD WASHER RESERVOIR FLUSHING PROCEDURE OUTLINED IN THIS TSB.

now making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

making steering wheel lock devices available directly to certain Kia vehicle owners. These devices can help deter a theft attempt. We are making this device available to customers free of charge and will ship it directly to customers who place orders within eighteen (18) months from the date of this letter.

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

once fully attached, are utilized in various Kia models and are strictly intended for ?one time use.? Some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.? It is critical for technicians to be aware that ALL such locking fasteners, regardless of type, are for ?one time use? only.

strictly intended for ?one time use?. Though not limited to the following, some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.?

regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.

REPEAT DTC P0128 AFTER REPLACEMENT OF THE THERMOSTAT, REMOVE THE THERMOSTAT HOUSING TO VERIFY IF THE THERMOSTAT WAS INSTALLED INCORRECTLY DURING THE PREVIOUS REPAIR.

incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.

illuminated with DTC(s) P0442, P0455, P0456, or P0457 (Evaporative Emissions System-Leak detected) and the evaporative (EVAP) leak self-test resulted in NTF, a manual EVAP test is recommended.

CAMERA OF SOME KIA VEHICLES (SEE TABLE ON PG. 6 FOR SPECIFIC MODELS AND PRODUCTION DATES) WHICH MAY EXHIBIT INADEQUATE IMAGE QUALITY FROM THE REAR VIEW CAMERA. DIAGNOSE THE CONCERNS USING THE INFORMATION IN THIS BULLETIN AND, IF NECESSARY, REPLACE THE REAR VIEW CAMERA WITH AN IMPROVED PART BY FOLLOWING THE APPLICABLE SERVICE PROCEDURE ON KGIS.