2010 Kia Forte TSBs

Kia is conducting a Product Improvement Campaign to perform a software update on 2010-2011 MY Kia Forte and Forte Koup vehicles equipped with 2.4-liter MPI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit (ECU).

DTC P1326 (PI2102Y/Z) - This bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information related to the Technical Service Bulletin previously published in (PI2102) titled Knock Sensor Detection System - ECU Logic Improvement for 2010-2011MY Forte and Forte Koup (TD)vehicles equipped with Theta 2.4L MPI engine, produced from February 24, 2009 through May 31, 2011. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

Kia is conducting This bulletin provides information related to the Technical Service Bulletin previously published in (PI2101) titled Knock Sensor Detection System - ECU Logic Improvement for 2011MY Sorento (XMa) vehicles equipped with Theta 2.4L MPI engine, produced from October 24, 2009 through June 24, 2011. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

Kia is conducting a Product Improvement Campaign to perform a software update on 2010-2011 MY Kia Forte & Forte Koup vehicles equipped with 2.4-liter engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU").

related to the Technical Service Bulletin previously published in (PI2102) titled "Knock Sensor Detection System - ECU Logic Improvement" for 2010-2011MY Forte and Forte Koup (TD) vehicles equipped with Theta 2.4L MPI engine, produced from February 24, 2009 through May 31, 2011. Specifically, this bulletin provides instructions on which procedures to follow if, after installation of the KSDS, any one of the subject vehicles below return to the dealer with Diagnostic Trouble Code (DTC) P1326 (Knock Signal Range/Performance).

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit. On some vehicles when the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly and does not affect the steering effort.

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to some Kia models that may exhibit fogging, condensation, and/or moisture inside a headlamp assembly. Generally, a fogging condition is considered normal and can be eliminated by turning on the headlamps with the engine running for up to 30 minutes or during normal driving conditions. Headlamp assembly replacement WILL NOT be necessary in most cases.

bulletin provides information related to a software update to the Engine Control Unit (ECU) to install the Knock Sensor Detection System (KSDS) in order to protect the engine from excessive connecting rod bearing damage.

conducting a Product Improvement Campaign to perform a software update on 2010-2011 MY Kia Forte and Forte Koup vehicles equipped with 2.4-liter MPI engines to protect the engine from excessive connecting rod bearing damage. The update will be done free of charge and will only involve the addition of newly developed computer software for the Engine Control Unit ("ECU") (PI2102).

Parts and Service Managers that Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2010-2011 MY Forte and Forte Koup vehicles equipped with 2.4-liter engines, manufactured from February 24, 2009 through May 31, 2011 (PI2102).

Kia is conducting a Product Improvement Campaign to perform a software update to the Engine Control Unit (ECU) to protect the engine from excessive connecting rod bearing damage on 2010-2011 MY Forte and Forte Koup vehicles equipped with 2.4-liter engines, manufactured from February 24, 2009 through May 31, 2011 (PI2102).

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Steering Column Housing, or Worm Gear Assembly. When the steering wheel is rotated a scraping noise can be heard originating from the lower bearing on the Worm Gear Assembly on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

bulletin has been revised to include additional information. New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU), Worm Gear Assembly or Steering Column Housing on some 2010MY~ Kia models listed on page 8, equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit. Follow the MDPS Flowchart (page 2) along with the MDPS DTC Table (page 3) procedure outlined in this bulletin before replacing the C-MDPS Motor, ECU or Steering Column Housing.

has been revised to include additional information.This bulletin provides information regarding the partial repair of the Motor Driven Power Steering (MDPS) Motor, Electronic Control Unit (ECU) or Steering Column Housing on some 2010MY~ Kia models listed on page 5 equipped with a Column Motor Driven Power Steering (C-MDPS) unit.

inspection and installation of the steel sealing ball on: * 3.3L & 3.8L Lambda engines for 2007-2008MY Sorento (BL), * 2.0L Nu engines for 2010-2019MY Soul (AM, PS), and * 1.8L & 2.0L Nu engines for 2010-2018MY Forte (TD, YD/YDm), 2019MY~ Forte (BDm). When replacing the cylinder heads on these engines, inspect the lubrication ports for installation of the steel sealing balls. Current replacement cylinder heads may not be equipped with the required steel balls. Identify and locate the nine (9) lubricant passages on 3.3L and 3.8L engines and three (3) on 1.8L and 2.0L engines and verify a steel ball is installed in each.

considered serviceable, and should be thoroughly cleaned and transferred to the new engine.

will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.

will be conducting a Voluntary Service Campaign, as a preventative measure, to apply additional anti-corrosion material to the underbody components of certain 2011-2014 MY Sorento, 2011-2014 MY Optima and Optima Hybrid, 2011-2014 MY Sportage, and 2010-2013 Forte and Forte Koup vehicles originally retailed or currently registered in one of the 28 states where heavy amounts of road salt are used.

SHARDS HAVE CONTAMINATED THE SYSTEM, THE DESICCANT OR THE ENTIRE A/C RECEIVER/DRYER ASSEMBLY MAY NEED TO BE REPLACED. THIS IS DUE TO THE FACT THAT IT MAY BE IMPOSSIBLE TO REMOVE ALL METAL CONTAMINANTS FROM THE RECEIVER/DRYER DURING THE A/C FLUSHING PROCEDURE. REFER TO THE INCLUDED TABLE FOR DETAILED INFORMATION ON COMPONENT REPLACEMENT BY MODEL. IF YOU SUSPECT A PLUGGED EXPANSION VALVE, THE INLET SCREENS CAN BE CLEANED. IF THE VALVE IS NOT EQUIPPED WITH AN INLET SCREEN AND IS RESTRICTED, THE EXPANSION VALVE MAY ALSO NEED TO BE REPLACED.

VALVE STEM ASSEMBLY"

IS CONDUCTING A VOLUNTARY SERVICE CAMPAIGN TO REPLACE THE TIRE VALVE STEM ASSEMBLIES IN CERTAIN 2010 MY FORTE VEHICLES THAT WERE ORIGINALLY SOLD IN OR ARE CURRENTLY REGISTERED IN THE STATES WHERE HEAVY AMOUNTS OF ROAD SALT ARE USED.

IS CONDUCTING A VOLUNTARY SERVICE CAMPAIGN TO REPLACE THE TIRE VALVE STEM ASSEMBLIES TO PREVENT GRADUAL LOSS OF TIRE PRESSURE IN CERTAIN 2010 MY FORTE, 2011 MY SORENTO AND 2010 MY SOUL VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE 21 SALT STATES WHERE HEAVY AMOUNTS OF ROAD SALT ARE USED. THE 21 SALT STATES ARE: CT, DC, DE, IA, IL, IN, MA, MD, ME, MI, MN, MO, NH, NJ, NY, OH, PA, RI, VT, WI, WV. IN ADDITION TO THE SALT BELT STATES, THE FOLLOWING STATES HAVE SUBSTANTIALLY RAISED THEIR USE OF ROAD SALT OVER THE YEARS AND ARE ALSO PART OF THIS SERVICE CAMPAIGN: KS, KY, NE, ND, SD, UT, AND AK.

WILL BE CONDUCTING A VOLUNTARY SERVICE CAMPAIGN, TO REPLACE THE TIRE VALVE STEM ASSEMBLIES IN CERTAIN 2010 MY SOUL, 2010 MY FORTE, AND 2011 MY SORENTO VEHICLES ORIGINALLY RETAILED OR CURRENTLY REGISTERED IN ONE OF THE SALT-BELT STATES.

HAS BEEN EXPANDED TO INCLUDE ALL STATES. THIS BULLETIN PROVIDES THE PROCEDURE TO REPLACE THE TIRE VALVE STEMS TO PREVENT GRADUAL LOSS OF TIRE PRESSURE IN SOME 2011MY SORENTO (XMA), 2010MY SOUL (AM) AND 2010MY FORTE (TD) VEHICLES WHICH WERE ORIGINALLY RETAILED OR ARE CURRENTLY REGISTERED IN STATES WHERE ROAD SALT IS HEAVILY USED. THE STATES ARE: CT, DC, DE, IA, IL, IN, MA, MD, ME, MI, MN, MO, NH, NJ, NY, OH, PA, RI, VT, WI, WV KS, KY, NE, ND, SD, UT, AND AK. THE VALVE STEM ASSEMBLY IN THE WHEELS CAN CRACK IF THEY BECOME CORRODED. SUCH CRACKS CAN CAUSE THE AIR IN THE TIRES TO LEAK OUT. HOWEVER, THE VALVE STEM ASSEMBLY IS EQUIPPED WITH A TIRE PRESSURE MONITORING SYSTEM (TPMS) AND A SUFFICIENT LEAK WILL RESULT IN THE ILLUMINATION OF THE TPMS WARNING LIGHT. IN SOME INSTANCES, A CRACKED VALVE CAN BREAK OFF WHEN ATTEMPTING TO ADD AIR TO THE TIRES. TO ADDRESS THIS CONDITION, REPLACE THE TIRE VALVE STEM FOR ALL FOUR TPMS SENSORS ON ALL AFFECTED VEHICLES, FOLLOWING THE PROCEDURE OUTLINED IN THIS BULLETIN. BEFORE CONDUCTING THE PROCEDURE, VERIFY THE VEHICLE IS INCLUDED IN THE LIST OF AFFECTED VINS."

THE ACTION WILL INVOLVE A REPROGRAM OF THE CRUISE CONTROL LOGIC AND IMPROVE ROUGH IDLE AND/OR P0304 LOGIC FOR 2.0L VEHICLES WITH VCM (VARIABLE CHARGE MOTION ACTUATOR). *PE

PROVIDES THE PROCEDURE TO UPGRADE THE POWERTRAIN CONTROL MODULE (PCM) OF SOME MODEL YEAR VEHICLES. REFLASH HAS ENHANCED VCM (VARIABLE CHARGE MOTION) ACTUATOR LOGIC TO IMPROVE A ROUGH IDLE CONDITION AT START UP OR A MIL ON AND STORED DTC P0304 SET AT START-UP. *PE

PROCEDURE TO UPGRADE THE POWERTRAIN CONTROL MODULE (PCM) OF SOME VEHICLES. THIS REFLASH HAS ENHANCED VCM (VARIABLE CHARGE MOTION) ACTUATOR LOGIC TO IMPROVE A ROUGH IDLE CONDITION AT START UP OR A MIL ON AND STORED DTC P0304 SET AT START UP. *PE

INFORMATION RELATED TO AN MDPS ECU SOFTWARE. JUST AFTER STARTING THE ENGINE, ON SOME OCCASIONS THE EPS LIGHT MAY ILLUMINATE ON AFFECTED VEHICLES DUE TO A DTC C2412. *PE

EXPERIENCE A MIL ON WITH DTC P0304 STORED IN MEMORY. IN MOST CASES THE DTC IS SET ONLY DURING A COLD START AND NORMALLY THE CUSTOMER DOES NOT NOTICE ANY ENGINE STUMBLE, ROUGHNESS OR PERFORMANCE ISSUES. *PE

SOME VEHICLES MANUFACTURED 7/16-8/20, 2009 MAY EXPERIENCE CONCERNS OF INOPERATIVE A/C BLOWER, HIGH/LOW COOLING FANS OR ENGINE STARTER MOTOR. THE CONCERN MAY BE CAUSED BY POOR CONTACTS INSIDE THE FOUR (4) RELAYS LOCATED IN THE ENGINE COMPARTMENT JUNCTION BOX. *PE

IF AT ANY TIME OCV IS SUSPECTED AS A CAUSE OF ROUGH IDLING, POOR ACCELERTION, CAMSHAFT TIMING MISALIGNMENT RELATED TROUBLE CODES, MISFIRE RELATED TROUBLE CODES ETC., ON THE VEHICLE EQUIPPED WITH THE CVVT SYSTEM, BE SURE TO PERFORM THE OCV INSPECTION PROCEDURE BELOW BEFORE REPLACEMENT. NO MODEL YEARS SPECIFIED. *PE

frequently asked questions regarding the Product Improvement Campaign (PI2102).

Parking Distance Warning (PDW) alerts and repairs involving ultrasonic sensors. The PDW system alerts the driver while parking, by calculating distance based on the difference in signal transmission and reception times between the vehicle (ultrasonic sensor) and an object. The membrane film of the ultrasonic sensor is used for object detention and can be damaged by stone chips or foreign substances while driving. Damage to the cover of the ultrasonic sensor can also lead to damage to the internal circuit. As a result of this external damage, the PDW system may not receive the proper signal from the ultrasonic sensor. In some cases, the system may cause a false alarm, no alert, or phantom warnings by a Warning Lamp to be displayed on the cluster. The ultrasonic sensor membrane film should be always inspected for external damage and if any part replacement should be treated as a general repair, not as a warranty claim repair for this concern. (Please note that this Pitstop only applies to models/trims that are equipped with the ultrasonic sensors.)

New/revised sections of this bulletin are indicated by a black bar in the margin area. This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, and the transmission oil cooler is transferred to the new transmission.

A flush is required ONLY when a transmission is replaced.

correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles in the chart starting on page 2.

This bulletin provides information relating to the correct transmission fluid type and fill quantity requirement for each Kia model. A flush is required ONLY when a transmission is replaced, refer to applicable vehicles on page 2. Refer to the shop manual on KGIS for the specific Kia model for the correct transmission fluid check/fill procedures.

TRANSMISSION FLUIDS THAT ARE REQUIRED FOR EACH KIA MODEL. REFER TO THE SHOP MANUAL ON KGIS FOR THE SPECIFIC KIA MODEL, THEN REFERENCE THE AUTOMATIC TRANSAXLE SYSTEM/ REPAIR PROCEDURES/ INSPECTION AND ADJUSTMENT SECTION FOR THE CORRECT ATF CHECK/FILL PROCEDURES.

IMPROVE TORQUE CONVERTER CLUTCH WHILE THE CRUISE CONTROL IS ACTIVATED. *PE

SOME VEHICLES (6 SPEED MANUAL TRANSAXLES) MAY HAVE INTERFERENCE WITH THE INNER TRI-POD HOUSING CONTACTING WITH THE AXLE SEAL CAGE. *PE

SOME VEHICLES MAY EXPERIENCE SLIGHT SHIFT HESITATION AND/OR TRANSAXLE SHIFT DELAY. THE TRANSMISSION CONTROL MODULE (TCM) IS AN INTEGRAL PART OF THE PCM AND SHOULD BE NOTED AS THE TCM IS REFERENCED. *PE

launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.

launching this service campaign to apply additional anti-corrosion material to the underbody components of certain 2011-2014MY Sorento, 2011-2014MY Optima and Optima Hybrid, 2011-2014MY Sportage, and 2010-2013MY Forte and Forte Koup vehicles originally sold or currently registered in one of the 28 states where heavy amounts of road salt are used. The 28 states where heavy amounts of road salt are used are: AK, CT, DC, DE, IA, IL, IN, KS, KY, MA, MD, ME, MI, MN, MO, ND, NE, NH, NJ, NY, OH, PA, RI, SD, UT, VT, WI and WV.

registered in the states where heavy amounts of road salt are used of a service campaign to add additional anti-corrosion material to underbody components of vehicle.

DEBRIS ACCUMULATION ON THE WINDSHIELD WASHER PUMP INLET FILTER. OVER TIME, SOME KIA VEHICLES MAY EXHIBIT A LIMITED APPLICATION OF WINDSHIELD WASHER FLUID WHEN THE WASHER FUNCTION IS USED. LIMITED APPLICATION OF WINDSHIELD WASHER FLUID CAN BE CAUSED BY FOREIGN DEBRIS ON THE WASHER PUMP INLET FILTER. TO CORRECT THIS CONDITION, REPLACE THE WASHER PUMP INLET FILTER AND PERFORM THE WINDSHIELD WASHER RESERVOIR FLUSHING PROCEDURE OUTLINED IN THIS TSB.

PROVIDES INFORMATION RELATING TO SOME FORTE KOUP (TD) VEHICLES BUILT THAT MAY HAVE ABNORMAL NOISE FROM THE SUNROOF DUE TO INTERFERENCE BETWEEN SUNROOF RAIL AND ROOF PANEL WHILE DRIVING ON UNEVEN ROADS OR WHEN CORNERING. *PE

USB ports and 12V power outlets to connect/charge mobile phones. Customers may experience issues with their head units that may be related to the use of aftermarket USB charging cables, including; * Electrical interference and limited or no functionality when attempting to play music, or when charging a device through the USB port * Excessive static or noise when listening to the audio source * Malfunctions and screen freeze of the head unit screen * Slow down of the system response while device is plugged in * Music will not play from iPhone 5 or 6 with Kia iPod cable and aftermarket adapter * No or limited functionality when trying to play music from an Apple device

The TPMS positioning from the manufacturer may be different from the positioning shown on a KDS.

THE CUSTOMER MAY STATE THAT THE VEHICLE WILL NOT FLASH THE HAZARD LIGHTS OR SOUND THE HORN WHEN LOCKING THE DOORS WITH THE TRANSMITTER. AS DESIGNED, THE VEHICLE SHOULD FLASH THE HAZARD LIGHTS AND SOUND THE HORN AFTER PRESSING THE LOCK BUTTON TWO (2) TIMES WITHIN FIVE (5) SECONDS. IF THIS CONCERN IS OCCURRING, VERIFY IF IT IS RELATED TO THE REMOTE START CONTROL MODULE BY CHECKING THE POSITION OF THE OVERHEAD INTERIOR LIGHT SWITCH. IF THE SWITCH IS IN THE OFF POSITION, MOVE THE SWITCH TO THE DOOR POSITION AND RETEST THE SYSTEM.

THIS SPECIAL SERVICE TOOL (SST) WAS DEVELOPED TO IMPROVE THE EFFICIENCY AND EFFECTIVENESS OF UPDATING 2010MY, AND LATER, KIA AUDIO HEAD UNITS USING A GDS, AND NOW, THE SAME FUNCTIONALITY IS AVAILABLE ON KDS. SOME TECHNICIANS MAY NOT BE AWARE OF THE BENEFITS THE AUM TOOL HAS TO OFFER. THE AUM ELIMINATES THE NEED FOR MULTIPLE USB FLASH DRIVES FOR SPECIFIC VEHICLE MODELS AND APPLICATIONS WHICH, IF MISAPPLIED, MAY RESULT IN AN IMPROPER AUDIO SYSTEM SOFTWARE UPDATE AND/OR LOCKED UP HEAD UNIT. ADDITIONALLY, FIELD REPORTS HAVE INDICATED THAT USB DRIVES FOR AUDIO UPDATES ARE EASILY LOST OR MISPLACED.

*JS

*RM

PROVIDING INFORMATION FOR THE NEW REQUIREMENTS RELATED TO LOAD CARRYING CAPACITY (LCC) WHEN CERTAIN ACCESSORIES ARE ADDED TO A COMPLETED VEHICLE PRI0R TO FIRST RETAIL SALE. *PE

substance found on some Kia vehicles, due to possible excess assembly oil applied during assembly.

once fully attached, are utilized in various Kia models and are strictly intended for ?one time use.? Some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.? It is critical for technicians to be aware that ALL such locking fasteners, regardless of type, are for ?one time use? only.

strictly intended for ?one time use?. Though not limited to the following, some examples are: axle shaft nuts with stake collar, cotter pins, washers with locking tabs and other similar hardware, including threaded fasteners with pre-applied ?thread-locking adhesives.?

regarding the procedure to repair the bulb connector on some 2010MY~ vehicles listed on the table below, which may exhibit a bulb connector concern. To correct this concern, replace the connector with a new and improved part.

RELATED TO CAMPAIGN SC098 AND HAS DETERMINED THAT AT TIMES DEALER STAFF MAY HAVE DIFFICULTY IN QUICKLY AND EASILY IDENTIFYING THE CORRECT SWITCHES WHILE ORDERING PARTS, PREPARING TO PERFORM THE STOP LAMP REPLACEMENT OR WHILE PREPARING TO RETURN REPLACED SWITCHES TO KMA (IN CASE OF AN EXISTING MANDATORY PART RETURN (MPR) REQUEST). TO FACILITATE FASTER AND EASIER IDENTIFICATION OF THE CORRECT PARTS, A PICTURE GUIDE AS SHOWN ON PAGE 2 IS PROVIDED. THE GUIDES CONTENT WAS PURPOSELY FORMATTED TO FIT ON ONE PAGE SO IT CAN BE EASILY PRINTED AND KEPT ON OR NEAR A WORKSTATION, PARTS COUNTER OR TOOL BOX.

REPEAT DTC P0128 AFTER REPLACEMENT OF THE THERMOSTAT, REMOVE THE THERMOSTAT HOUSING TO VERIFY IF THE THERMOSTAT WAS INSTALLED INCORRECTLY DURING THE PREVIOUS REPAIR.

identify and record the head unit software level on various head unit platforms and generations.

(ELE091) (Rev 1) - This bulletin provides the procedure on how to identify and record the head unit software level on various head unit platforms and generations. This procedure will now be required when ordering head units through the Direct Exchange Program (see Parts Bulletin 91-961-0005).

RECORD THE HEAD UNIT SOFTWARE LEVEL ON VARIOUS HEAD UNIT PLATFORMS AND GENERATIONS. THIS PROCEDURE WILL NOW BE REQUIRED WHEN ORDERING HEAD UNITS THROUGH THE DIRECT EXCHANGE PROGRAM.

*RM

INFORMATION RELATING TO AN UPGRADE OF THE FUNCTIONING OF THE LOGIC IN THE AIR BAG CONTROL UNIT IN SOME VEHICLES TO INCREASE THE RANGE OF IMPACTS IN WHICH THE SIDE AND CURTAIN AIRBAGS WILL DEPLOY. PROVIDES INFORMATION ON HOW TO REPROGRAM THE ACU. *PE

THIS MAY RESULT IN THE INTERMITTENT ILLUMINATION OF THE SEAT BELT WARNING LIGHT AND SOUNDING OF THE SEATBELT WARNING CHIME, EVEN WITH THE DRIVER'S SEAT BELT PROPERLY BUCKLED. *PE

incorporate a defogging logic to prevent the interior windows from becoming excessively fogged. Depending on the specific model, the HVAC control head monitors ambient temperature and/or cabin humidity to determine which settings will best prevent the windows from fogging. If the system detects lower ambient temperature or higher cabin humidity, the defogging logic may automatically switch ON the A/C, and/or set the air intake mode to Fresh Air. If the user changes these settings, the defogging logic will take control again after 3 to 5 minutes, depending on the procedure in this publication.

AN IMPROVED FUEL CAP WITH A LARGER HANDLE DESIGN FOR IMPROVED FEEL DURING TIGHTENING AND A FULL THREAD STOP WHICH PRODUCES ONE CLICK DURING TIGHTENING INSTEAD OF THE SEVERAL CLICKS HEARD ON THE PREVIOUS FUEL CAP DESIGN. *PE