2025 Jeep Wrangler TSBs

have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

Diagnostic Trouble Code (DTC) P083F- Clutch Pedal Position Sensor Performance.

Confirm if coolant is visibly dripping from the weeper chamber. 2.Root Cause identification The weeper chamber is designed to collect small amounts of coolant (< 3 ml/h) that pass through the dynamic seal. Red traces or shadows around the chamber may appear during initial operation due to seal adaptation or vapor condensation. These traces are not necessarily signs of a leak. Continuous dripping of coolant, however, indicates a malfunction. 3.Service Repair Procedure Lift the vehicle using an elevator. Verify if coolant is actively dripping from the weeper chamber. Run the engine at idle, alternating speed between 2000 4000 rpm for 15 minutes. Observe the weeper chamber during this test: If coolant continues to drip: Replace the water pump (possible permanent damage to the dynamic seal). If dripping stops: No further action is needed; the vehicle can be returned to the customer. 4.Clarify Leak Sources Do not confuse leaks from: The Press-In-Place rubber gasket (between water pump and engine block), or The inlet pipe nipples with leaks from the weeper chamber.

Multiple Systems Repair Bundle Campaign Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0133 - O2 Sensor 1/1 Slow Response. P2251 - O2 Sensor 1/1 Negative Current Control Circuit/Open. P0131 - O2 Sensor 1/1 Circuit Low. P2626 - O2 Sensor 1/1 Pump Cell Current Trim Circuit/Open. P0607 - ECU Internal Performance. C140A - Transfer Case Motor Control. P02EE - Cylinder 1 injector Circuit Performance. P02EF - Cylinder 2 injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. U0109 - Lost Communication With Fuel Pump Control Module. P0330 - Knock Sensor 2 Circuit. P023B - Charge Air Cooler Coolant Pump "A" Control Circuit Low. P2110 - Electronic Throttle Control - Forced Limited RPM. Customers may also experience one or more of the following: The electronic throttle inspection required indicator illuminates on the Instrument Panel Cluster (IPC). Seatbelt warning light and warning sound do not go off even when the passenger seat belt is fastened. Coolant leak from under the long life coolant reserve tank. Fuel cap strap broken. Door not opening / hard to open for both right side doors. Lumber switch inoperative. Right front seat cover stitch is tore out. Header seal deformation. This bulletin involves performing multiple inspections and repairs based on the listed Customer Symptoms.

This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.

Multiple Systems Repair Bundle Campaign Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): U11E3-00 - TCM Lost Communication With ESM On DPT CAN. B15A1-00 - Media Port 1 Connection. U11C2 - Lost Transmission Message. U11E4-00 - CAN Communication Messages Missing. U120C - Lost Brake Booster Signal. U1216-00 - Lost Communication With DASM. U121E-00 - Lost Communication With Steering Wheel Cruise Control Switch. U1267-00 - No Valid Data From ESM On CAN-C Or CAN-DPT. U12A8 - Lost Communication With Master Cylinder Pressure Sensor. U1465-00 - Implausible Driver Shift Request Signal Received. U1466-00- Implausible Driver Shift Request Signal Received On DPT CAN. U1515-87 - Steering Column Lock Secret Code - Missing Message. U1517-87 - Body Controller Secret Code - Missing Message. B2206-00 - Current VIN Missing/Mismatch. B2225-00- ( SCM) Steering Column Module Internal. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0607-00 - ECU Internal Performance. P1DD2-00 - Torque Request Signal From TCM Denied. U0100-00 - Lost Communication With ECM/PCM. U0101-00 - Lost Communication With TCM. U0102-00 - Lost Communication With Transfer Case Control Module/AWD. U0103-00 - Lost Communication With Electric Gear Shift Module. U0121-00 - Lost Communication With Anti-lock Brake System (ABS) Control Module. U0125 - Lost Communication With Dynamics Sensor. U0129-00 - Lost Communication With Brake System Control Module. U0140-00 - Lost Communication With Body Control Module. U0151-00 - Lost Communication With Occupant Restraint Controller (ORC). U0155-00 - Lost Communication With Cluster/CCN. U0159-00 - Lost Communication With Parking Assist Control Module. U017E - Lost Communication With Seatbelt Sensor 1. U0212-00 - Lost Communication With Steering Column Control Module. U0213-00 - Lost Communication With Interior Mirror Control Module "A". U0415-00 - Implausible Data Received From ABS. U0418-86 - Implausible Data Received From Brake System Control Module 1 - Signal Invalid. U0422-00 - Implausible Data Received From Body Control Module. U110A-00 - Lost Communication With SCM-CAN-C. U110C - Lost Fuel Level Message. U110E - Lost Ambient Temperature Message. U1110-00 - Lost Vehicle Speed Message. U1120 - Lost Wheel Distance Message. U113E-00 - Lost Communication With Intelligent Battery Sensor. U114C-00 - Lost Communication With PRNDL Display. U115F-00 - Lost Communication With Driver Presence Detection Module. U1175-00 - Lost Ignition Status Message. U1186 - Lost Communication With Adaptive Cruise Control Module. U1199 - Lost Hood Ajar Switch Voltage Message. U11B9-00 - Lost Communication With RF Hub. U11BC - Lost Brake Switch Message. U11BF - Lost Brake Pedal Position Message. P2453-00 - Differential Pressure Sensor A Circuit Range/Performance. P245F-00 - Diesel Particulate Filter Pressure Sensor "B" Circuit. C140A-11 - Transfer Case Motor Control. Customers may also experience one or more of the following: Android Auto not working. Radio screen is black for one to two seconds while driving and then returns to normal operation. Transfer Case Control Module (TCCM) wiring incorrectly routed. Noise from the front axle. Decals on the left and right fenders are peeling off. Right hand side speaker not working or exhibits a rattle noise. USB port not working. Interior rearview mirror delaminating. Tailgate glass damper mounting is peeling off or has come off. Abnormal noise from chain tensioner. Radio control on steering wheel malfunctions or has a delay in response This bulletin involves performing multiple inspections and repairs based on the listed Customer Symptoms.

There may also be associated driveability issues. Upon further investigation, the following fault codes may be found in the PCM:

the instrument cluster 2- Check if there is a fob Low battery active DTC Fob battery 1 DTC B1A10-00 or Fob battery 2 DTC B1A11-00 3- Check if the original battery is installed which Varta or Panasonic sized CR 2450 4- Verify if the fob ID printed under the battery cover matches fob IDs stored in the RFHUB, use DID $A004 - Engineering Development Data 1 (FOB ID 1 & 2) to check the fob IDs in the RFHUB 5- Check the voltage of the coin battery, replace the battery only if the voltage is 2.3V or below and report the voltage in the dealer narratives

return line This bulletin involves replacing the turbocharger oil return line.

roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

"Service Shifter, Stop Safely, Shut Off Engine To Engage Park" message displayed on the Instrument Panel Cluster (IPC). NOTE: Auto park will engage once the driver seat belt is unbuckled and the driver door is opened. This bulletin involves inspecting transmission shifter operation and possibly replacing the transmission shifter.

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.

has become detached, it is not necessary to replace the glass assembly. For loose or detached electrical tab, refer to TSB 23-007-25 for repair procedures on reattaching a loose tab. For burned or discolored gridlines on hard tops, DO NOT change the complete Flipper glass assembly. This discoloration is oxidation of the ceramic silver material and is normal. The Engineering standard call out the fact that this bus bar will change in color and is not a deterioration of the material or performance.

Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: Rough idle. Valvetrain noise. "

Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.

the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0133 - O2 Sensor 1/1 Slow Response. P2251 - O2 Sensor 1/1 Negative Current Control Circuit/Open. P0131 - O2 Sensor 1/1 Circuit Low. P2626 - O2 Sensor 1/1 Pump Cell Current Trim Circuit/Open. P0607 - ECU Internal Performance. C140A - Transfer Case Motor Control. P02EE - Cylinder 1 injector Circuit Performance. P02EF - Cylinder 2 injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. U0109 - Lost Communication With Fuel Pump Control Module. P0330 - Knock Sensor 2 Circuit. P023B - Charge Air Cooler Coolant Pump "A" Control Circuit Low. P2110 - Electronic Throttle Control - Forced Limited RPM. Customers may also experience one or more of the following: **The electronic throttle inspection required indicator illuminates on the Instrument Panel Cluster (IPC).** Seatbelt warning light and warning sound do not go off even when the passenger seat belt is fastened. Coolant leak from under the long life coolant reserve tank. Fuel cap strap broken. Door not opening / hard to open for both right side doors. Lumber switch inoperative. Right front seat cover stitch is tore out. Header seal deformation. This bulletin involves performing multiple inspections and repairs based on the listed Customer Symptoms.

the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0133 - O2 Sensor 1/1 Slow Response. P2251 - O2 Sensor 1/1 Negative Current Control Circuit/Open. P0131 - O2 Sensor 1/1 Circuit Low. P2626 - O2 Sensor 1/1 Pump Cell Current Trim Circuit/Open. P0607 - ECU Internal Performance. C140A - Transfer Case Motor Control. P02EE - Cylinder 1 injector Circuit Performance. P02EF - Cylinder 2 injector Circuit Performance. P02F0 - Cylinder 3 Injector Circuit Performance. P02F1 - Cylinder 4 Injector Circuit Performance. U0109 - Lost Communication With Fuel Pump Control Module. P0330 - Knock Sensor 2 Circuit. P023B - Charge Air Cooler Coolant Pump ""A"" Control Circuit Low. P2110 - Electronic Throttle Control - Forced Limited RPM. Customers may also experience one or more of the following: Seatbelt warning light and warning sound do not go off even when the passenger seat belt is fastened. Coolant leak from under the long life coolant reserve tank. Fuel cap strap broken. Door not opening / hard to open for both right side doors. Lumber switch inoperative. Right front seat cover stitch is tore out. Header seal deformation. This bulletin involves performing multiple inspections and repairs based on the listed Customer Symptoms."

Please return all associated parts which includes the snap rings so that the parts can be review by engineering."

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.

vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: Oil found on the ground beneath the vehicle. "

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

If the Turbo is being replaced for a noise or a rattle, inspect the wastegate for binding. The actuator kit is serviced separately. If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed oring for a leak. The o-ring is serviced separately

If the Turbo is being replaced for a noise or a rattle, inspect the wastegate for binding. The actuator kit is serviced separately. If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed o-ring for a leak. The o-ring is serviced separately.

Vehicles

Vehicles

a proper evaluation of the issue. If this does not correct the issue, please follow the steps in SOL: S2508000039

This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.

This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.

Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.

Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.

Mopar all-weather floor mats, especially the front mats. The all-weather mats are installed without removing the slit/perforation portion of the front carpet, which blocks the drain port on the all-weather mats completely and does not allow water/any liquid to get drained out of the vehicle through the drain hole on the underbody floor. Correct Installation Method for Mopar All-Weather Floor Mats 1. Find the slit/perforation on the front carpet (near the outboard mat post on the carpet )and cutout that piece from carpet. 2. Remove Drain Plug on the drain hole on the underbody floor 3. Install the All-Weather Mat. Make sure the mats built-in drain port lines up correctly into the drain hole on the floor. 4. Insert the drain plug in the drain port on all-weather mat to close the drain port. The plug is to be removed whenever there is need to drain water on the mat or to wash out dirt without removing the mat form the vehicle.

This causes several problems: . Dealers often install all-weather mats without removing the carpet cutout, which completely blocks the drain. . Missing drain plug claims occur because the plug is not clearly visible. . Customers find it difficult to locate and access the drain plug, especially when the vehicle is muddy. Correct Installation Method for Mopar All-Weather Floor Mats To ensure proper drainage, follow these steps: 1. Identify the Issue: . Some owners place the all-weather mats directly over the carpet, blocking the drain hole even though the mat has a drain port. 2. Locate the Carpet Cutout: . Under the mat area, there is a pre-cut carpet section designed to be removed. 3. Remove the Carpet Piece and Plug: . Lift or cut out the small square of carpet to expose the metal floor. . Remove the rubber drain plug from the Jeeps floor. 4. Install the Floor Mat: . Place the all-weather mat back into position. . Align the mats built-in drain tube with the drain hole on the floor to form a proper seal. 5. Reinstall the Plug into the Mat: . Insert the drain plug (removed from the floor) into the drain hole on the mat. . This allows you to open the plug anytime to wash out dirt or water without removing the mats. Benefits . Enables washing the mats with a hose while they remain inside the vehicle; water drains directly to the ground instead of soaking the carpet. . Prevents water from getting trapped under the mat, avoiding carpet damage.

If the switch has no physical damage, is not broken or separated, but still doesn't stay in place, verify that the bezel brackets that hold it in place are broken and are the cause of the problem. If the bezel is broken, and the switch is not, replace only the bezel trim, DO NOT replace the switch. If there's miscalibration in the power top, and there's no physical damage to the switch and it works accordingly, DO NOT replace the switch.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

chatter/streak/jump/skip/smear or make noise while traveling across the windshield.

Observation: The owner complains the top system is inoperative and that by pressing the switches the Power Top does not make any movement. Technician may or may not have Diagnostic Trouble Codes (DTCs). Repair Procedure: Perform the power top calibration prior to any switch or parts replacement.

Terminal Detached From The Glass.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): C2206-00 - Vehicle Configuration Mismatch. NOTE: DTC C2206-00 can trigger after a recent aftermarket tire installation or tire modification. This updated software is to address this DTC set by this condition. C2318-49 - Front Camera - Internal Electronic Failure. Customers may experience the following: "ACC/FCW Unavailable Service Required" message intermittently in the Instrument Panel Cluster (IPC). , updated Diagnostics section, new LOP and an updated Repair Procedure. This Technical Service Bulletin (TSB) has also been released as a Rapid Service Update (RSU) 26-017, date of issue January 31, 2026. All applicable RSU VINs have been loaded. To verify this RSU service action is applicable to the vehicle, use VIP or perform a VIN search in DealerCONNECT/Service Library. All repairs are reimbursable within the provisions of warranty. REPAIR SUMMARY: This bulletin involves **inspecting and possibly** reprogramming the DASM with the latest available software. J08 FSAR-RSU-6929 -2-

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): C2206-00 - Vehicle Configuration Mismatch. NOTE: DTC C2206-00 can trigger after a recent aftermarket tire installation or tire modification. This updated software is to address this DTC set by this condition. C2318-49 - Front Camera - Internal Electronic Failure. Customers may experience the following: "ACC/FCW Unavailable Service Required" message intermittently in the Instrument Panel Cluster (IPC) This bulletin involves reprogramming the DASM with the latest available software.

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

illumination and the vehicle must exhibit/set **one or more of the following Diagnostic Trouble Codes (DTCs)**: **C2206-00 Vehicle Configuration Mismatch. NOTE: DTC C2206-00 can trigger after a recent aftermarket tire installation or tire modification. This updated software is to address this DTC set by this condition. C2318-49 - Front Camera - Internal Electronic Failure.** Customers may experience the following: "ACC/FCW Unavailable Service Required" message intermittently in the Instrument Panel Cluster (IPC). This bulletin involves reprogramming of the DASM with the latest available software.

DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): B143A-13 - Microphone 1 - Circuit Open. B143D-13 - Microphone 2 - Circuit Open. Customers may also comment on one or more of the following: SOS light is illuminated. Customer can hear incoming calls but can't be heard on the other end. This bulletin involves replacing the **Microphone, Audio** assembly.

on the following: Radio screen displays "Uconnect Box Error" with the message "Uconnect Box requires service. Please visit an authorized dealer" This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.53 to 5.65 software level.

Current controls are not robust against depleted auxiliary battery condition. Please follow SOL S2508000031.

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0133 - O2 Sensor 1/1 Slow response. P2453 - Particulate Filter Pressure Sensor A Circuit Range/Performance. P245F - Particulate Filter Pressure Sensor B Circuit Range/Performance This bulletin involves reprogramming the PCM with the latest available software.

Tire Pressure Sensors Values Are Not Displayed

illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): C2318-49 - Front Camera - Internal Electronic Failure. Customers may experience the following: ""ACC/FCW Unavailable Service Required"" message intermittently in the Instrument Panel Cluster (IPC) This bulletin involves reprogramming of the DASM with the latest available software."

experience one or more of the following: - Error display of ""Uconnect Box Requires Service/Wifi Unavailable"" popups; [ TBM DTC B22A9-96 Internal Performance Failure ]. - Error display of ""Uconnect Box Requires Service"" pop-ups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ]."

about vehicle theft due to ability of key FOBs to be programmed through RFHM. Software enhancement includes: Update to the RFHM software to prevent hackers from programming their own key fob to the vehicle. This is intended to deter an unwanted drive off of the vehicle without the customer's knowledge This bulletin involves updating the RFHM module with the latest available software."

Quiet Vehicle Pedestrian Module (QVPM) Sound Is Not OK. Discussion: If diagnostic trouble code (DTC) B277904 is present and or QVPM is inoperative or sound is not okay, before replacing the module please check first the following service instructions: Perform the BODY VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Body Control (BCM) - Standard Procedure).

Jeep Gladiator This bulletin applies to vehicles built on or before May 05, 2025 (MDH 0505XX) equipped with Global Telematics Box Module (TBM) (Sales Code RDG). This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.15, 5.41 or 5.43 to 5.53 software level"

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

The rear window glass left or right side defrost solder terminal is detached from the defrost grid. This bulletin involves replacing the Electric Backlite (EBL) wire connector repair and re-securing the electrical connector(s) to the rear window"

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

collapsed and has been pushed inside the overhead console Fig. 1. NOTE: The switch will still operate the top after being pushed in. This bulletin involves inspecting the power top switch and possibly replacing the overhead console bezel.

Plan.

This bulletin involves replacing the front power outlet."

Add felt shim 68736674AA - 43MM OD x 10mm ID x 1mm thick. "

or B1570-93

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

or rattles This bulletin involves applying a foam strip to the back side of the sound bar speaker assembly.

messages text cut-off ""Transfer to Passenger"". Missing active call details in phone widget after swap is performed. Missing Pop-up messages for Blind Spot related to Lane Management on/off. Virtual wall option in menu present (should be removed). Customer need to select Sound type in EV pages twice. Apple Car Play icon on main screen disapears when ACP is activ This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from U33.43 and U35.18 To U37"

reset to the Display and see if concern is resolved. Currently no dealer claims with this issue stating the RVC image is affected."

Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process

the following Diagnostic Trouble Code (DTC): P083F - Clutch Pedal Switch A/B Correlation. Customers may also experience the following: Vehicle no start. Vehicle stop/start disabled. and new Repair Procedure. Revisions that are not highlighted with **asterisks** include removal of the Inspection steps. This Technical Service Bulletin (TSB) has also been released as a Rapid Service Update (RSU) 25-247, date of issue December 04, 2025. All applicable RSU VINs have been loaded. To verify this RSU service action is applicable to the vehicle, use VIP or perform a VIN search in DealerCONNECT/Service Library. All repairs are reimbursable within the provisions of warranty. REPAIR SUMMARY: **This bulletin involves replacing the clutch interlock switch.**

the following Diagnostic Trouble Code (DTC): P083F - Clutch Pedal Switch A/B Correlation. Customers may also experience the following: Vehicle no start. Vehicle stop/start disabled. This bulletin involves inspecting the clutch interlock switch and possibly replacing the clutch interlock switch.

Also, when reinstalling the harness, route the harness properly and secure it at all the retention points.

Hot', 'Fully Release Clutch Pedal' and 'Reduce Clutch Use' Lights are on in the Instrument Panel Cluster (IPC). Vehicle is in a 'limp-in' state This bulletin involves reprogramming the PCM with the latest available software.

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.

used as the reason for unit replacement. Visible ""glitter"" or debris in the pan does not justify complete unit replacements."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."

transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch"

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch"

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

TPM Lamp On.

assemblies are fogged with a light layer of condensation on the inside of the lenses. "

Reference Master Tech article released in January 2026 for updated diagnostic and testing procedures. Master Tech link: https: //mastertech.playerlync.net/app/player/p2tQVm

Reference Master Tech article released in December 2025 for updated diagnostic and testing procedures. Master Tech link: https: //mastertech.playerlync.net/app/player/p2tQVm

Rear Axle Noise Customers may experience the following: Intermittent grinding, screeching, ratcheting noise coming from the right hand side of vehicle on the rear axle This bulletin involves cleaning and lubricating the axle shaft and hub splines.

"

from the right hand side of vehicle on the rear axle This bulletin involves cleaning and lubricating the axle shaft and hub splines."

from the right hand side of vehicle on the rear axle. This bulletin involves cleaning and lubricating the axle shaft and hub splines."

from the right hand side of vehicle on the rear axle. This bulletin involves cleaning and lubricating the axle shaft and hub splines."

Parking Brake Will Not Release Customers may comment on the following: Park brake will not release. This bulletin involves using glue to repair the park brake handle positioning.

vehicle will leak water from the top of the B-pillar when the vehicle is parked on a downward incline. Water on door trim or carpet. Water drips down the inside door and panel This bulletin includes performing a water test and possibly adding foam pads to both Freedom Panels."

In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.

If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

Q AND 19 - Steering / Diagnosis and Testing (IN SERVICE LIBRARY). PLEASE REFER 19 - Steering / Linkage / END, Tie Rod / Diagnosis and Testing IF YOU HAVE BALL JOINT LOOSENESS CONCERN. PLEASE DO NOT REPLACE DRAG LINK AND TIE ROD UNLESS PART HAS VISIABLE DAMAGE OR FREE PLAY EXCEEDS SPECS."

Q AND 19 - Steering / Diagnosis and Testing (IN SERVICE LIBRARY). PLEASE REFER 19 - Steering / Linkage / END, Tie Rod / Diagnosis and Testing IF YOU HAVE BALL JOINT LOOSENESS CONCERN. PLEASE DO NOT REPLACE DRAG LINK AND TIE ROD UNLESS PART HAS VISIABLE DAMAGE OR FREE PLAY EXCEEDS SPECS.