2023 Jeep Wrangler TSBs

have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

Diagnostic Trouble Code (DTC) P083F- Clutch Pedal Position Sensor Performance.

Confirm if coolant is visibly dripping from the weeper chamber. 2.Root Cause identification The weeper chamber is designed to collect small amounts of coolant (< 3 ml/h) that pass through the dynamic seal. Red traces or shadows around the chamber may appear during initial operation due to seal adaptation or vapor condensation. These traces are not necessarily signs of a leak. Continuous dripping of coolant, however, indicates a malfunction. 3.Service Repair Procedure Lift the vehicle using an elevator. Verify if coolant is actively dripping from the weeper chamber. Run the engine at idle, alternating speed between 2000 4000 rpm for 15 minutes. Observe the weeper chamber during this test: If coolant continues to drip: Replace the water pump (possible permanent damage to the dynamic seal). If dripping stops: No further action is needed; the vehicle can be returned to the customer. 4.Clarify Leak Sources Do not confuse leaks from: The Press-In-Place rubber gasket (between water pump and engine block), or The inlet pipe nipples with leaks from the weeper chamber.

and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P08A6 - Gear Lever Position Sensor System - Multiple Sensor Correlation. P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation. Customers may also comment on one or more of the following: Service Transmission message on in the Instrument Panel Cluster (IPC) due to clutch slip detection with the transfer case in neutral. Clutch is overheating. Clutch is slipping on engagement. Inability to accelerate uphill. Vehicle does not start. Vehicle is stuck in limp-home mode. This bulletin involves reprogramming the PCM with the latest available software.

Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.

This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.

There may also be associated driveability issues. Upon further investigation, the following fault codes may be found in the PCM:

that were not used in this application. To simplify the design, the connector has been optimized and updated to a 10-pin configuration.

engine idle when cold starting the engine. Low coolant level in coolant recovery bottle.

roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

Upon further investigation the technician **must** find the following Diagnostic Trouble Code (DTC) has been set: P1B0F-00 - Drive Motor A Position Sensor Offset Incorrect. Customers may also experience one or more of the following: Vehicle goes into limp home mode. Vehicle does not start. This bulletin involves inspecting the MGU serial number and possibly replacing the MGU as needed."

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.

has become detached, it is not necessary to replace the glass assembly. For loose or detached electrical tab, refer to TSB 23-007-25 for repair procedures on reattaching a loose tab. For burned or discolored gridlines on hard tops, DO NOT change the complete Flipper glass assembly. This discoloration is oxidation of the ceramic silver material and is normal. The Engineering standard call out the fact that this bus bar will change in color and is not a deterioration of the material or performance.

Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: Rough idle. Valvetrain noise. "

Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.

exhibit/set the following Diagnostic Trouble Code (DTC): P0341 - Camshaft Position Sensor - Performance Bank 1 - Sensor 1. This bulletin involves repairing the cam sensor harness and re-routing the generator wiring."

illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance. Customers may also experience one or more of the following: The check engine light illuminates. Overheating of the transmission fluid. This bulletin involves reprogramming the TCM with the latest available software."

illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00- Torque Converter Clutch Performance. Customers may also experience one or more of the following: The check engine light illuminates. Overheating of the transmission fluid. REPAIR SUMMARY: This bulletin involves reprogramming the TCM with the latest available software. "

Upon further investigation the technician must find one or more of the following Diagnostic Trouble Code (DTC) has been set: P0C19-00 - Drive Motor A Torque Delivered Performance. P1B03-00 - Resolver Signal / MCPA Rationality. Customers may experience the following: Electric Vehicle (EV) system shuts down while transferring over to Internal Combustion Engine (ICE) motive power. Engine Stop Start (ESS) function will also not operate as a result of this condition This bulletin involves reprogramming the Auxiliary Hybrid Control Processor (AHCP) also known as PIM, with the latest available software."

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.

vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may comment on the following: Oil found on the ground beneath the vehicle. "

Vehicle Shakes During A Cold Start And Noise Is Heard Near The P2 Motor. DTCs U0287-00 And B273C-00

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

If the Turbo is being replaced for a noise or a rattle, inspect the wastegate for binding. The actuator kit is serviced separately. If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed oring for a leak. The o-ring is serviced separately

illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): C140E-00 - Transfer Case Motor Blocked. This bulletin involves reprogramming the DTCM with the latest available software and possibly replacing the transfer case motor actuator."

There may be Diagnostic Trouble Codes (DTCs) present. "

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: P1B0F-00 - Drive Motor A Position Sensor Offset Incorrect. Customers may experience one or more of the following: Vehicle goes into limp home mode. Vehicle does not start. This bulletin involves inspecting the MGU serial number and possibly replacing the MGU as needed."

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** **P02EE - Cylinder 1 Injector Circuit Performance (China Only). P02EF - Cylinder 2 Injector Circuit Performance (China Only). P02F0 - Cylinder 3 Injector Circuit Performance (China Only). P02F1 - Cylinder 4 Injector Circuit Performance (China Only).** P2B95 - Cold Start Injection Pulse Performance. **Customers may also comment on the following: A ""Performance Limited Service Fuel System"" message appears and then disappears after a few seconds/ minutes in the Instrument Panel Cluster (IPC) (China Only).** This bulletin involves reprogramming the PCM with the latest available software."

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P1129 - closed loop fueling not achieved - Bank 2 Upstream. P0158 - O2 Sensor 2/2 circuit high. P0152 - O2 Sensor 2/1 circuit high. P2504 - Charging system output high. P0563 - Battery/system voltage high. Customers may also experience the following: The engine runs rough. This bulletin involves reprogramming the PCM with the latest available software."

Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section ""System Operation - Smart Charging System"". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC."

body replacement."

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures."

Diagnostic Trouble Code (DTC) P0341 ? Camshaft Position Sensor Performance ? Bank 1 Sensor 1, Set.

Customer complaints may include a noise coming from under de hood described as a squeal, screech, squeak, chirp or "belt related" noise and/or noisy tensioner/pulley. Please check Service Library for any STAR Online publications that may apply. Note: If it is found that the pulleys and/or tensioners are to blame for the noise please use an stethoscope or similar tool to determine the origin of the noise and include it in the narrative.

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present.

INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. CAUSE: INTAKE Hydraulic Lash Adjuster may have a manufacturing issue that can cause the plunger to stick, generating valvetrain noise.

published diagnostic information for this DTC to ensure all module connections are secure. Please check all the connections at BCM from other modules that could potentially report a loss of communication with the BCM and ensure that they are fully seated as per diagnostic information. Some affected modules may include:Amplifier (AMP), IPC, HVAC,Radio, Digital TV, TPM, PCM, ORC, DTCM, SCCM, CVPM, EHPS, ICS, PTCM, OCM, PTS, PAM, DAS, DPDM, CSWM, ESM, ABS, PSSM, EAM, TBM, HCP, RF Hub, ASBS, LBSS, RBSS, AHLM, ITM, TCM. *Ensure to check all the wiring harness connected to BCM with Other Modules are proper. *Please disconnect the Battery Negative Cable for 15 minutes and then reconnect. *Clear the codes and check to see if any active DTC's return for U0140 *If still DTCs U0140 presents then contact Engineering Expert: FCA Redacted Content

Customer complaint may include a noise from under the hood described as a squeal, screech, squeak, chirp or belt-related noise and/or noisy tensioner/pulley. Please refer to SOL# S2309000007.

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

If no response in 15 minutes, proceed with repair.

Misfire or rough running.

There may be Diagnostic Trouble Codes (DTCs) present.

There may be Diagnostic Trouble Codes (DTC)s present.

NOTE: The power door locks will still function normally. This bulletin involves inspecting the door lock cylinders and possibly replacing one or more lock cylinders or re-attaching the key cylinder linkage clip.

There may be Diagnostic Trouble Codes (DTC)s present. This bulletin involves inspecting and if needed, replacing the intake HLAs. NOTE: **ALL VEHICLES ON THE RSU VIN LIST REQUIRE ALL 12 INTAKE HYDRAULIC LASH ADJUSTERS TO BE REPLACED**.

Upon further investigation the technician may find that the multiple Diagnostic Trouble Codes (DTCs) have been set: ? C1403-29 - Transfer Case Range Position Sensor-Signal Invalid. ? C14AA-62 - Transfer Case Motor Position Sensor Supply-Signal Compare Failure. This bulletin involves reprogramming the DTCM with the latest software available.

This bulletin involves inspection the overflow coolant bottle for leaks and replacing it if needed.

presence, only AB or previous LEVEL PSU right intake camshaft PN 05047913AA or AB (old version) should be replaced. If the engine is equipped with the AC/AD LEVEL PSU right intake camshaft PN 05047913AC or AD (new version), camshaft should NOT be replaced. Case 2) If the intake camshaft or intake rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).

noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).

There may be Diagnostic Trouble Codes (DTC)s present. This bulletin involves inspecting and if needed, replacing the intake HLAs.

Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P016F - Closed Loop Fuel Pressure Control At Limit - Pressure Too Low. ? P025C - Fuel Pump Module Control Circuit Low. ? P0300-00 - Multiple Cylinder Misfire. ? P0301-00 - Cylinder 1 Misfire. ? P0302-00 - Cylinder 2 Misfire. ? P0303-00 - Cylinder 3 Misfire. ? P0304-00 - Cylinder 4 Misfire. ? P0305-00 - Cylinder 5 Misfire. ? P0403-00 - EGR Control Circuit Open (Disabled Fault). ? P208B - Reductant Pump 1 Control Performance. Other Software enhancements: ? Low speed engine idle improvements. ? Improved engine restart performance and torque response during low fuel level and/or hot ambient conditions. This bulletin involves reprogramming the PCM with the latest available software.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present.

INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. CAUSE: INTAKE Hydraulic Lash Adjuster may have a manufacturing issue that can cause the plunger to stick, generating valvetrain noise.

Intake Manifold Runner Valve Diagnostic Trouble Codes (DTCs) Setting In Extreme Cold Ambient Temperatures.

Check hose routing as outlined in Star Online Publication S2208000205 or on a known good vehicle before replacing valve. Routing hoses correctly will likely fix the issue.

P0E80-00-Coolant Bypass Valve "B" Control Stuck Closed

Vehicles

Vehicles

This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.

This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.

Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.

Replace axle shaft and seal together. Do not replace seal only. Keep original seal and axle shaft and send the parts as fast track.

Vehicles

Vehicles

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

chatter/streak/jump/skip/smear or make noise while traveling across the windshield.

Observation: The owner complains the top system is inoperative and that by pressing the switches the Power Top does not make any movement. Technician may or may not have Diagnostic Trouble Codes (DTCs). Repair Procedure: Perform the power top calibration prior to any switch or parts replacement.

Simplification

Simplification

Terminal Detached From The Glass.

H 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification

G 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification

G 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification

F 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification

Gladiator (JT) - Corrosion Warranty Claim Simplification

Corrosion Warranty Claim Simplification

Corrosion Warranty Claim Simplification (Rev. D)

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

Water On Front Floor.

Window Stops Part Way Down.

switch 2) Please check the continuity on each pin of the switch based on the table found in the service Procedures. If after testing switch is still faulty, please call FCA Redacted Content. If no response after 15 minutes, proceeds with switch replacement.

This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim (Fig. 1) .Zinc Shim

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim. (Fig. 1) .Zinc Shim

Gladiator (JT) - Corrosion Warranty Claim Simplification (Rev. A)

Corrosion Warranty Claim Simplification (Rev. A)

Corrosion Warranty Claim Simplification

If no response in 15 minutes, proceed with repair. Please take pictures of the broken part and email the pictures to FCA Redacted Content.

Window Stops Part Way Down.

switch 2) Please check the continuity on each pin of the switch based on the table found in the service Procedures. If after testing switch is still faulty, please call FCA Redacted Content. If no response after 15 minutes, proceeds with switch replacement.

Gladiator (JT) - Corrosion Warranty Claim Simplification (Rev. B)

Corrosion Warranty Claim Simplification (Rev. B)

This bulletin involves checking the torque values on the Sky One-Touch power top screws and replacing all 16 screws if required.

This bulletin involves inspecting and if necessary installing missing rear jounce bumper(s).

This bulletin involves inspecting and possibly connecting the heated windshield button to the windshield.

This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim (Fig. 1) .Zinc Shim

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim. (Fig. 1) .Zinc Shim

Gladiator (JT) - Corrosion Warranty Claim Simplification (Rev. A)

Corrosion Warranty Claim Simplification (Rev. A)

Corrosion Warranty Claim Simplification

Terminal Detached From The Glass.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

andreplacing all 16 screws if one is found with an incorrect torque value. Customers may experience the following: A rattle noise over bumps and rough roads while driving coming from the roof area.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE

about vehicle theft due to ability of key FOBs to be programmed through RFHM. Software enhancement includes: Update to the RFHM software to prevent unauthorized keyfob programming. This is intended to deter an unwanted drive off of the vehicle without the customer's knowledge. This bulletin involves updating the RFHM module with the latest available software.

Tire Pressure Sensors Values Are Not Displayed

experience one or more of the following: - Error display of ""Uconnect Box Requires Service/Wifi Unavailable"" popups; [ TBM DTC B22A9-96 Internal Performance Failure ]. - Error display of ""Uconnect Box Requires Service"" pop-ups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ]."

Jeep Gladiator This bulletin applies to vehicles built on or before May 05, 2025 (MDH 0505XX) equipped with Global Telematics Box Module (TBM) (Sales Code RDG). This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from 5.15, 5.41 or 5.43 to 5.53 software level"

Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only."

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

The rear window glass left or right side defrost solder terminal is detached from the defrost grid. This bulletin involves replacing the Electric Backlite (EBL) wire connector repair and re-securing the electrical connector(s) to the rear window"

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

dealerships root cause or diagnose the issue of the heated steering wheel system. Before replacing or ordering replacement parts (steering wheel, switches and wire harness) because of Heated Steering Wheel Inoperative And Or Not Hot Enough concern please review Star On Line S2423000045 for further details

Diagnostic Trouble Code (DTC) C2201-49 FDCM/FTCM Internal Internal Electrical Failure, Set.

sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

notification on customers mobile application."

for any physical issue (Button stuck, broke). If not, physical issue is found move to next step 2.- Make sure all the switches harness are properly connected, disconnect the switch and reconnect it, and reverify the issue. If after performing these steps the switch remains faulty, please replace the switch

experience one or more of the following: Remote door lock and unlock commands sent from the Jeep mobile app fail. After saving the edited charge or climate schedule in the radio, the mobile app reverts it back to the schedule set on the Jeep mobile app. Remote operation ignition on remote start not working. Customer not receiving a monthly email containing the VHR (Vehicle Health Report). This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 5.15 to 5.43. NOTE: National launch for this FOTA update is expected to begin June 14, 2024."

""Performance Limited Fuel System"" with no Diagnostic Trouble Codes (DTCs). This bulletin involves inspecting the N17 circuit of the High Pressure Fuel Pump Solenoid harness for contact with a cooling system hose clamp."

""Performance Limited Fuel System"" with no Diagnostic Trouble Codes (DTCs). This bulletin involves inspecting the N17 circuit of the High Pressure Fuel Pump Solenoid harness for contact with a cooling system hose clamp."

U0131 Lost Communication With Electro Hydraulic Power Steering Control Module (EHPS)."

The parts kit (SENSOR KIT, Axle: 68544629A$) must be used to repair the Axle Locker Sensor on JL/JT equipped with the M210 and M220 Tru-Lok axles (DSE). Internal axle components are serviceable. Complete axle assemblies should not be replaced unless necessary due to damaged housing. Over repairs may be subject to chargeback."

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? C1451-11 - Service Axle Locker System** Customers may also comment on a Service Axle Locker message displayed in the Electronic Vehicle Information Center (EVIC) for this condition.

life degradation shown when viewing fuel and oil data screen. This bulletin involves reprogramming the PCM with the latest available software.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0607-00 - ECU Internal Performance. ? P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. This bulletin involves updating the BPCM with the latest available software.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

trim panel not seated flush (large gap). This bulletin involves inspecting and if needed move wire harness retainer to lower mounting location.

trim panel not seated flush (large gap). This bulletin involves inspecting and if needed move wire harness retainer to lower mounting location.

Service Electric Power Steering Message On Cluster.

Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ?P0A80-00 - Replace Hybrid/EV Battery Pack. ? P0EDD-00 - Contactor Wear Counter Far Advanced. In addition, the customer may comment on the following condition: ? Battery light on in the Instrument Panel Cluster (IPC). This bulletin involves updating the BPCM with the latest available software.

please contact FCA redacted content. If no response in 15 minutes, proceed with repair.

Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P2B95 - Cold Start Injection Pulse Performance. This bulletin involves reprogramming the PCM with the latest available software.

Redacted Content for further assistance. If no response in 15 minutes, proceed with repair.

Upon further investigation, a technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P2B95 - Cold Start Injection Pulse Performance. This bulletin involves reprogramming the PCM with the latest available software.

Upon further investigation the technician may find the following DTC has been set: ? B1271-00 - Charge Level Indicator Internal. Customer may also experience the following: ? BCI does not indicate charge status while the vehicle is charging. This bulletin involves replacing the BCIM.

Ambient Air Temperature Sensor Circuit-Circuit Short to Battery or Open, P0073 Ambient Air Temperature Sensor Circuit High

The parts kit (SENSOR KIT, Axle: 68544629A$) must be used to repair the Axle Locker Sensor on JL/JT equipped with the M210 and M220 Tru-Lok axles (DSE).

Diagnostic Trouble Code (DTC) P203E ? Reductant Level Sensor 1 Circuit Intermittent-Erratic Set.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

part number 68443445A$.

P0D27, ensure to clear the codes and perform a charging test. If the codes come back again, proceed with the replacement.

Tire Pressure Sensors Values Are Not Displayed

Diagnostic Trouble Codes P0407 ? EGR Sensor B Circuit Low, or P0408 ? EGR Sensor B Circuit High Set

Order the "R" part number for all orders:

Add felt shim 68736674AA - 43MM OD x 10mm ID x 1mm thick. "

Adding Remote Start

Adding Remote Start

Programmed

? Horn sound is very low. ? Horn is physically dissembling. This bulletin involves inspecting both horn date codes and replacing the horn(s) if needed.

this is normal and not a defect.

If this occurs on the driver side, the vehicle will not be able to be driven (the seat back will be locked forward). This bulletin involves replacing both front seat position returns.

If this occurs on the driver side, the vehicle will not be able to be driven (the seat back will be locked forward). This bulletin involves replacing both front seat position returns.

C0604- Active Air Dam Control Performance

above a (80 KMPH) speed - instead of one time chime alert. This bulletin involves performing a restore vehicle configuration procedure.

Also, when reinstalling the harness, route the harness properly and secure it at all the retention points.

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.

used as the reason for unit replacement. Visible ""glitter"" or debris in the pan does not justify complete unit replacements."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."

transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch"

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch"

in reverse or blank screens when selecting the rear camera view following a recent service repair involving the removal and installation of the rear spare tire carrier

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch. "

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

DTSs U11C3, U1069, U0074, U114C

the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits.

the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

Leaks can be caused by possible porosity of transmission case or Oil Cooler Lines.

Pan/filter replacement are not required.

Leaks can be caused by possible porosity of transmission case or Oil Cooler Lines. Refer to the latest version of Star Online Publication S2321000005.

Leaks can be caused by possible porosity of transmission case or Oil Cooler Lines.

Pan/filter replacement are not required.

? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.82F to QR40.12. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.

? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.5 to QR40.11. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.

Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.2 to QR40.11. NOTE: National launch for this FOTA update is expected to begin February 19, 2023.

continues to reboot after a Map Update (MOTA). ? Navigation regularly cuts out and back on again. ? Radio switches to navigation without customer's input. This bulletin involves updating the Navigation maps via USB.

Auto? does not work or is intermittently working when their device is plugged into the center console bin USB port. This replacing the center console USB cable.

? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from Q339.3 to QR39.62. NOTE: The National launch for this FOTA update campaign is expected to begin December 04, 2023.

? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.

following symptoms: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.6 to QR40.12. NOTE: National launch for this FOTA update is expected to begin November 06, 2023.

? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

TPM Lamp On.

assemblies are fogged with a light layer of condensation on the inside of the lenses. "

TPM Lamp On.

assemblies are fogged with a light layer of condensation on the inside of the lenses."

assemblies are fogged with a light layer of condensation on the inside of the lenses.

assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.

This bulletin involves installing missing side steps.

This bulletin involves installing missing side steps. NOTE: Vehicles were ordered with the side step option but did not get the side steps from the factory.

This bulletin involves installing missing side steps. NOTE: Vehicles were ordered with the side step option but did not get the side steps from the Factory.

assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.

This bulletin involves installing missing side steps.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

The purpose of this informative Technical Service Bulletin (TSB) is to support the Network on the following topics: Discern the different kinds of connected service issues (onboard / offboard). Support the customer in his journey to open a request via Customer Care. Address on the correct actions to properly manage a customer complaining about the received assistance."

PRIOR TO PERFORMING ANY THERMOSTAT REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2309000014

Library for specifications so a suitable alternative can be used

replaced such as diesel fuel filters. Occasionally, components are replaced before their standard life expectancy or when not contaminated with debris.

Occasionally, components are replaced before their standard life expectancy or when not contaminated with debris "

Occasionally, components are replaced before their standard life expectancy or when not contaminated with debri "

If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ?P04EC - EVAP System Large Leak Detected - Fuel Tank Side. ? P04EE - EVAP System Very Small Leak Detected - Fuel Tank Side. Customers may also comment the following: ? There is a "Check Gas Cap" message in the Instrument Panel Cluster (IPC). NOTE: The above condition is caused from an air leak through the fuel filler cap and fuel filler neck seal, because the fuel filler cap tether is caught between both. This bulletin involves removing the fuel filler cap tether and replacing it with a shorter tether.

Parking Brake Will Not Release Customers may comment on the following: Park brake will not release. This bulletin involves using glue to repair the park brake handle positioning.

vehicle will leak water from the top of the B-pillar when the vehicle is parked on a downward incline. Water on door trim or carpet. Water drips down the inside door and panel This bulletin includes performing a water test and possibly adding foam pads to both Freedom Panels."

In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.

sunvisor body mounts.

Due to brake vacuum pumps being returned with trouble not found, please follow the proper diagnostics outline in the service library this also includes checking all electrical and vacuum hose connections prior to replacement of the vacuum pump. This will avoid unnecessary repair and potential charge back on the vacuum pump.

Due to brake vacuum pumps returned with trouble not found, please follow the proper diagnostics outline in the service library this also includes checking all electrical and vacuum hose connections prior to replacement of the vacuum pump. This will avoid unnecessary repair and potential charge back on the vacuum pump.

This bulletin involves installing two pieces of foam pads.

Reference Master Tech article released in January 2026 for updated diagnostic and testing procedures. Master Tech link: https: //mastertech.playerlync.net/app/player/p2tQVm

Reference Master Tech article released in December 2025 for updated diagnostic and testing procedures. Master Tech link: https: //mastertech.playerlync.net/app/player/p2tQVm

"

Please contact FCA REDACTED CONTENT. ~ If no response in 15 minutes, proceed with repair.

C15AD-92-Ride Height System- Performance In Below Freezing Temperatures.

type noise, verify the noise is not coming from the transfer case. Follow the diagnostic procedure outlined in SOL Publication S2303000001 prior to any repair.

Q AND 19 - Steering / Diagnosis and Testing (IN SERVICE LIBRARY). PLEASE REFER 19 - Steering / Linkage / END, Tie Rod / Diagnosis and Testing IF YOU HAVE BALL JOINT LOOSENESS CONCERN. PLEASE DO NOT REPLACE DRAG LINK AND TIE ROD UNLESS PART HAS VISIABLE DAMAGE OR FREE PLAY EXCEEDS SPECS."

Q AND 19 - Steering / Diagnosis and Testing (IN SERVICE LIBRARY). PLEASE REFER 19 - Steering / Linkage / END, Tie Rod / Diagnosis and Testing IF YOU HAVE BALL JOINT LOOSENESS CONCERN. PLEASE DO NOT REPLACE DRAG LINK AND TIE ROD UNLESS PART HAS VISIABLE DAMAGE OR FREE PLAY EXCEEDS SPECS.

Electric Steering Column Lock (ESCL) Does Not Function, Steering Wheel Locked. DTCs U1433-62, U1412-62, U1517-62 In The ESCL

E adds 2024 model year vehicles and updates the Collision Service Bulletin number

B)

Winch Cable Binding.