2015 Jeep Wrangler TSBs

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

(248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following Diagnostic Trouble Codes (DTCs) have been set: **P0335 - Crankshaft Position Sensor Circuit. P0306 - Cylinder 6 Misfire (Automatic Transmissions only). P0456 - EVAP System Small Leak (3.6L Engine Sales Code ERB only).** U0140 - Lost Communication With Body Control Module.

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

when traveling at low speeds or when shifting into gear please call Jian Zhu on his cell at (248) 379-1132 prior to replacing the transmission. Jian is looking to get information. Also, Engineering would like to visit a dealers located in the SE Michigan area with a vehicle exhibiting the above complaint. If Jian cannot be reached within 15 minutes proceed with the repair.

(TPM) issue for TPM lamp ON.~ Prior to replacing any components (Sensor or TPM Control Module) on MY15 or 16 JK vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.

close properly, please also replace the console base and the lock cylinder (04746315) in addition to the console lid. If you have any questions, please call Mike Wicker on cell (248) 821-9350 prior to replacing the component. If you don?t receive a response within 15 minutes, please continue with normal repair procedure.

when traveling at low speeds or when shifting into gear please call Jian Zhu on his cell at (248) 379-1132 prior to replacing the transmission. Jian is looking to get information. Also, Engineering would like to visit a dealers located in the SE Michigan area with a vehicle exhibiting the above complaint. If Jian cannot be reached within 15 minutes proceed with the repair.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

flag nut to knock it loose from e-coat that has dried it in place.

inspection and repair of the engine wire harness and replacing the harness retainer tower clip. A small number of customers may experience a MIL illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1 set in the Powertrain Control Module (PCM) memory.

information regarding this part.~ Bob Smith ? Cell (248) 202-9458 - Robert.M.Smith@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

when traveling at low speeds or when shifting into gear please call Jian Zhu on his cell at (248) 379-1132 prior to replacing the transmission. Jian is looking to get information. Also, Engineering would like to visit a dealers located in the SE Michigan area with a vehicle exhibiting the above complaint. If Jian cannot be reached within 15 minutes proceed with the repair.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or the following symptoms. Upon further investigation the technician may find the Diagnostic Trouble Code (DTC) listed below: ? P1239 Engine Oil Temperature Too Low. ? Perceived misfire under normal acceleration. ? Starter protection feature will be disabled.

Jerry Tomlin at cell (248) 202-5329. If no response within 15 minutes, continue with repair.~ Engineering is investigating whether the sensors are getting contaminated with oil. For any other P-Code besides P0137, follow the applicable diagnostic procedure.

Vijay Thiruvenkatachary at cell (906) 281-8495.~ Before replacing the Left Downstream (2/2) O2 Sensor on a 3.6L JK due to a P0157 fault code, please call Jerry Tomlin at cell (248) 202-5329. ~ Engineering would like determine whether the sensor has been contaminated with oil.~ If no response is received within 15 minutes, then continue with repair. For all other fault codes, please perform the applicable diagnostic routine.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following Diagnostic Trouble Codes (DTCs) have been set: **P0335 - Crankshaft Position Sensor Circuit. P0306 - Cylinder 6 Misfire (Automatic Transmissions only). P0456 - EVAP System Small Leak (3.6L Engine Sales Code ERB only).** U0140 - Lost Communication With Body Control Module.

(TPM) issue for TPM lamp ON.~ Prior to replacing any components (Sensor or TPM Control Module) on MY15 or 16 JK vehicles, please contact Raja Charabuddi on cell (248) 202-7313. If no response within 15 minutes, proceed with repair.

close properly, please also replace the console base and the lock cylinder (04746315) in addition to the console lid. If you have any questions, please call Mike Wicker on cell (248) 821-9350 prior to replacing the component. If you don?t receive a response within 15 minutes, please continue with normal repair procedure.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

(248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

Gaurav Saxena at cell (248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following Diagnostic Trouble Codes (DTCs) have been set: **P0300 - Multiple Cylinder Misfire (3.6L Engine Sales Code ERB only). P0306 - Cylinder 6 Misfire (Automatic Transmissions only).** P0335 - Crankshaft Position Sensor Circuit. P0456 - EVAP System Small Leak (3.6L Engine Sales Code ERB only). U0140 - Lost Communication With Body Control Module.

If no answer and if you do not receive a return call within 15 minutes please continue with the normal repair.~

close properly, please also replace the console base and the lock cylinder (04746315) in addition to the console lid. If you have any questions, please call Mike Wicker on cell (248) 821-9350 prior to replacing the component. If you dont receive a response within 15 minutes, please continue with normal repair procedure."

(TPM) ISSUE FOR TPM LAMP ON.~ PRIOR TO REPLACING ANY COMPONENTS (SENSOR OR TPM CONTROL MODULE) ON MY15 OR 16 JK VEHICLES, PLEASE CONTACT RAJA CHARABUDDI ON CELL (248) 202-7313. IF NO RESPONSE WITHIN 15 MINUTES, PROCEED WITH REPAIR."

ENGINEERING IS SEEKING INFORMATION REGARDING THIS PART.~ DYE MUST BE USED TO DETERMINE WHERE THE LEAK IS COMING FROM BEFORE REPLACING. ALSO PLEASE CHECK THE RECENTLY UPDATED SERVICE BULLETIN NUMBER 09-008-15. ~ FIRST: NICK MORAND CELL (248) 410-5078 - NICK.MORAND@FCAGROUP.COM SECOND: BOB JACKSON CELL (248) 944-0466 - BOB.JACKSON@FCAGROUP.COM THIRD: JOE LOVELL CELL (734 309-6467 - JOE.LOVELL@FCAGROUP.COM IF A RESPONSE IS NOT RECEIVED WITHIN 15 MINS, THEN PROCEED WITH THE NECESSARY REPAIR."

CLOSE PROPERLY, PLEASE ALSO REPLACE THE CONSOLE BASE AND THE LOCK CYLINDER (04746315) IN ADDITION TO THE CONSOLE LID. IF YOU HAVE ANY QUESTIONS, PLEASE CALL MIKE WICKER ON CELL (248) 821-9350 PRIOR TO REPLACING THE COMPONENT. IF YOU DONT RECEIVE A RESPONSE WITHIN 15 MINUTES, PLEASE CONTINUE WITH NORMAL REPAIR PROCEDURE."

REPLACING THE HARNESS RETAINER TOWER CLIP. *LJ

SEE DOCUMENT SEARCH BUTTON BELOW. FIAT CHRYSLER 2015 JEEP WRANGLER: RECALL APPLIES TO 3.6L ENGINE BUILT THROUGH OCTOBER 15, 2014. PCM MAY NOT DETECT A FAILED OXYGEN SENSOR. POSSIBLY IN AN INCREASE IN TAILPIPE EMISSIONS WHICH COULD EXCEED FEDERAL/CALIFORNIA EMISSIONS STANDARDS. *LJ

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

The customer may describe discoloring or rust from the lower nut securing the doors to the hinges.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Diagnostic Trouble Codes P0407 ? EGR Sensor B Circuit Low, or P0408 ? EGR Sensor B Circuit High Set

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Module (PCM) with update software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.

Sensor (SAS).If the diagnostic tests indicate the clockspring/SAS requires replacement, replace the clockspring, upper and lower steering column shrouds and steering wheel back cover. Some customers may experience the illumination of the airbag warning lamp or traction control indicator lamp. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: B1B00 - Driver Airbag Squib 1 Circuit Low. B1B01 - Driver Airbag Squib 1 Circuit High. B1B02 - Driver Airbag Squib 1 Circuit Open. B1B03 - Driver Airbag Squib 1 Circuit Shorted Together. B1B04 - Driver Airbag Squib 2 Circuit Low. B1B05 - Driver Airbag Squib 2 Circuit High. B1B06 - Driver Airbag Squib 2 Circuit Open. B1B07 - Driver Airbag Squib 2 Circuit Shorted Together. C123F - Steering Angle Sensor Comparative Performance. C1219 - Steering Angle Sensor Erratic Performance. C2205 - Steering Angle Sensor Internal. P0579 - Speed Control Multiplexed Switch #1 Performance. P0581 - Speed Control Multiplexed Switch #1 High. P0591 - Speed Control Multiplexed Switch #2 Performance. P0593 - Speed Control Multiplexed Switch #2 High. U1109 - Lost Communication With Lin Steering Wheel Controls.

following: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE If a connector repair kit is not available on the website contact FCA Redacted Content to see if an alternative repair kit is available for your application prior to ordering the harness. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

Gurdial Dhami at cell (226) 346-7919. If you do not receive a return call after 15 minutes, please proceed with repair.

The customer may describe discoloring or rust from the lower nut securing the doors to the hinges.

The customer may describe the security system nuisance alarms with no apparent cause for activation.

Module (PCM) with update software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.

Before replacing the wheel speed sensors, please check for wiring/connection to the speed sensor. If the sensor is replaced, record the fault codes and note any damage to the sensor.~

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Sensor (SAS).If the diagnostic tests indicate the clockspring/SAS requires replacement, replace the clockspring, upper and lower steering column shrouds and steering wheel back cover. Some customers may experience the illumination of the airbag warning lamp or traction control indicator lamp. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: B1B00 - Driver Airbag Squib 1 Circuit Low. B1B01 - Driver Airbag Squib 1 Circuit High. B1B02 - Driver Airbag Squib 1 Circuit Open. B1B03 - Driver Airbag Squib 1 Circuit Shorted Together. B1B04 - Driver Airbag Squib 2 Circuit Low. B1B05 - Driver Airbag Squib 2 Circuit High. B1B06 - Driver Airbag Squib 2 Circuit Open. B1B07 - Driver Airbag Squib 2 Circuit Shorted Together. C123F - Steering Angle Sensor Comparative Performance. C1219 - Steering Angle Sensor Erratic Performance. C2205 - Steering Angle Sensor Internal. P0579 - Speed Control Multiplexed Switch #1 Performance. P0581 - Speed Control Multiplexed Switch #1 High. P0591 - Speed Control Multiplexed Switch #2 Performance. P0593 - Speed Control Multiplexed Switch #2 High. U1109 - Lost Communication With Lin Steering Wheel Controls.

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

This bulletin involves reprogramming the Powertrain Control Module (PCM) with update software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

The customer may describe discoloring or rust from the lower nut securing the doors to the hinges.

Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE

For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

this is normal and not a defect.

Side Steps are missing. Inspect for and if necessary install the Side Steps.

semi and full synthetic oils.

missing, check STAR Parts - there is a button cover replacement kit available. The part numbers for the buttons are as follows: Left - 68359329A$ Right - 68375214A$

Side Steps are missing. Inspect for and if necessary install the Side Steps.

Side Steps are missing. Inspect for and if necessary install the Side Steps.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair

Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair

Side Steps are missing. Inspect for and if necessary install the Side Steps.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

. The customer may describe water dripping from the top, running down the inside of the back glass, or running down the inside rear D-pillar.

the prop rod is correct and acceptable. Please do not replace the Prop Rod for this condition.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

. The customer may describe water dripping from the top, running down the inside of the back glass, or running down the inside rear D-pillar.

the prop rod is correct and acceptable. Please do not replace the Prop Rod for this condition.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)

B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)

A)

- All Dealers

industry awareness regarding the recommended usage of Authentic Mopar Glass.

there is a single skipped zipper tooth.

There is a drain hole along the rear edge of the panel (in car position). After draining the panels, inform the customer of the drain hole and if the issue returns they can drain the panels themselves. Storage of panels outdoors in certain positions will cause water infiltration.~ ~ For a water leak from the center front edge of the Targa Top Panels, do not replace the panels, replace the SEAL, Targa Top (Part Number 68088055AA).

The customer may describe water dripping from the top, running down the inside of the back glass, or running down the inside rear D-pillar.

the prop rod is correct and acceptable. Please do not replace the Prop Rod for this condition.

This bulletin involves inspecting the Julian date on the left rear close out panel. Zinc coating missing from left rear close out panel, no corrosion protection.

frame and A-pillar between the door to close gaps and prevent water leaks. The customer may describe gaps between the windshield frame, door and top of cowl. There may also be a water leak.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.

Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.

bracket to the front axle and checking alignment settings after repair. The customer may describe a vibration and/or shimmy at a low speed condition.

industry awareness regarding the use of recycled or salvage parts.

Prior to ordering any of the parts (55057300A$, 55057293A$, 55057301A$, 55057294A$) Please contact Micah Straub at cell phone# 248-613-2478 for further instructions. Leave a voice mail and your call will be returned promptly. 5.1 to 7.8 is the correct resistance value although ambient temperature will affect this value. Please call for detailed information. If no return call in 15 minutes, proceed with repair.

industry awareness regarding the use of recycled or salvage parts.

bracket to the front axle and checking alignment settings after repair. The customer may describe a vibration and/or shimmy at a low speed condition.

bracket to the front axle and checking alignment settings after repair. The customer may describe a vibration and/or shimmy at a low speed condition.

Prior to ordering any of the parts (55057300A$, 55057293A$, 55057301A$, 55057294A$) Please contact Micah Straub at cell phone# 248-613-2478 for further instructions. Leave a voice mail and your call will be returned promptly. 5.1 to 7.8 is the correct resistance value although ambient temperature will affect this value. Please call for detailed information. If no return call in 15 minutes, proceed with repair.

A customer may experience, poor audio quality and vehicles with RHB radios may have poor navigation language.

A customer may experience poor audio quality and vehicles with RHB radios may have poor navigation language.

A customer may experience poor audio quality and vehicles with RHB radios may have poor navigation language.

A customer may experience poor audio quality and vehicles with RHB radios may have poor navigation language.

A customer may experience, poor audio quality and vehicles with RHB radios may have poor navigation language.

The customer may experience poor audio sound quality.

A customer may experience poor audio quality and vehicles with RHB radios may have poor navigation language.

A customer may experience, poor audio quality and vehicles with RHB radios may have poor navigation language.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

Module (TCM) with the latest available software. A small number of customers may experience one or more of the following transmission related concerns. ? Less than desired shift response when towing or driving up steep hills in high ambient temperatures. ? Delayed shift when driving in 4WD Low. ? Vibration or resonance in the cabin on acceleration from a cruising speed.

Squeak noise from under the dash while depressing or releasing the clutch pedal.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

CUSTOMERS ARE EXPERIENCING DELAYED SHIFT RESPONSE WHEN DRIVING UP HILLS, VIBRATION ON ACCELERATION FROM A CRUISING SPEED. *LJ

and replacing seat cushion cover, on the driver?s front seat. The customer may describe, the driver?s front leather seat has dimples in the seat bottom. The dimples are caused by openings in the heated seat element, seeFig.1.Dimple Location On Leather Seats1 - Dimples

and replacing seat cushion cover, on the driver?s front seat.The customer may describe, the driver?s front leather seat has dimples in the seat bottom. The dimples are caused by openings in the heated seat element, seeFig.1.Dimple Location On Leather Seats1 - Dimples

If no response in 15 minutes, continue with repair.

Blend door is not moving to heat. Before replacing the actuator call Matt Sasina at cell (248) 464-4982.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

prior to purchase, the attached "Important Notice" document and retain a signed copy. No customer symptoms or conditions are associated with this RRT. If a customer?s VIN is listed in VIP or your RRT VIN list, RRT applies only to those unsold Vins listed.

prior to purchase, the attached "Important Notice" document and retain a signed copy. No customer symptoms or conditions are associated with this RRT. If a customer?s VIN is listed in VIP or your RRT VIN list, RRT applies only to those unsold Vins listed.

prior to purchase, the attached ""Important Notice"" document and retain a signed copy. No customer symptoms or conditions are associated with this RRT. If a customers VIN is listed in VIP or your RRT VIN list, RRT applies only to those unsold Vins listed."

B)

been machined with an incorrect taper during the manufacturing process on about 250 of the above vehicles, with approximately 80 of the axles sold by Mopar aftermarket. This condition can result in premature axle knuckle wear. The aftermarket front axle knuckles must be replaced with new axle knuckles for the left side and right side.

The Customer commnunication requested return of unsold inventory to inpsect for possible incorrect direction threads (right hand rather than left hand). Incorrect direction threads will prevent it from being installed.

been machined with an incorrect taper during the manufacturing process on about 250 of the above vehicles, with approximately 80 of the axles sold by Mopar aftermarket. This condition can result in premature axle knuckle wear. The aftermarket front axle knuckles must be replaced with new axle knuckles for the left side and right side.

If you don't receive response within 15 minutes, please continue with normal repair procedure.

If you don't receive response within 15 minutes, please continue with normal repair procedure.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

IF YOU DON'T RECEIVE RESPONSE WITHIN 15 MINUTES, PLEASE CONTINUE WITH NORMAL REPAIR PROCEDURE."

bushing on driver and passenger side seat slide mechanism to resolve a squeaking issue (Two door models only). The customer may describe a squeak heard under the front passenger or driver side seat, while turning or driving over bumps.

bushing on driver and passenger side seat slide mechanism to resolve a squeaking issue (Two door models only). The customer may describe a squeak heard under the front passenger or driver side seat, while turning or driving over bumps.