2013 Jeep Wrangler TSBs

this is normal and not a defect.

this is normal and not a defect.

semi and full synthetic oils.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Cracked upper swing gate hinge cover.

Cracked upper swing gate hinge cover.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

and pulls out, it is necessary to replace both upper and lower swinggate hinges - p/n 55395401AG

Cracked upper swing gate hinge cover.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

MODEL 2013-2014 WRANGLER. *PE

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

The customer may experience a buzz, squeak or rattle (BSR) at idle speeds.

Control Module (TCM) with new software. NOTE: This bulletin applies to the following vehicles: Wrangler vehicles equipped with the WA580 Automatic Transmission (Sales Code DGJ) Challenger vehicles equipped with either the 3.6L engine (Sales Code ERB) or the 6.4L Engine (Sales Code ESH or ESG) and the WA580 Automatic Transmission (.Sales Code DGJ) Durango vehicles equipped with the 3.6L engine (Sales Code ERB) and the WA580 Automatic Transmission (Sales Code DGJ) Grand Cherokee vehicles equipped with the 6.4L engine (Sales Code ESG) for all markets except Australia (Sales Code 8AL) or the 3.6L engine (Sales Code ERB) (All Markets) and the WA580 Automatic Transmission (Sales Code DGJ). Australian vehicles equipped with the 6.4L can refer to Service Bulletin 21-010-14

tube and if necessary installing a protective sleeve on the transmission oil cooler tube. The customer inquires about Recall N28 and power steering return lines are not available, although the vehicle was built on or before February 23, 2013 (MDH 022317) equipped with 3.6L engine (sales code ERB), automatic transmission (sales code DGJ), left hand drive (sales code 5I8).

The customer may experience a buzz, squeak or rattle (BSR) at idle speeds.

tube and if necessary installing a protective sleeve on the transmission oil cooler tube. The customer inquires about Recall N28 and power steering return lines are not available, although the vehicle was built on or before February 23, 2013 (MDH 022317) equipped with 3.6L engine (sales code ERB), automatic transmission (sales code DGJ), left hand drive (sales code 5I8).

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

flag nut to knock it loose from e-coat that has dried it in place.

inspection and repair of the engine wire harness and replacing the harness retainer tower clip. A small number of customers may experience a MIL illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1 set in the Powertrain Control Module (PCM) memory.

Control Module (TCM) with new software. The customer may experience one or more of the following: Grand Cherokee/Durango 3.6L Engine (Sales Code ERB) ? Erratic shifting complaints while driving up steep hills or towing during hot ambient temperature conditions. ? Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). ? Poor performance and/or poor powertrain response when trying to accelerate from speeds >58 kph (36 mph) - All Markets. ? Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. ? Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer. Grand Cherokee 6.4L Engine (Sales Code ESG) ? Poor acceleration or performance above 113 kph (70 mph). ? Transmission shifting while accelerating from a stop does not meet customers expectation. ? Harsh shifting during acceleration with moderate accelerator pedal and then lifting off the accelerator pedal. ? Cannot accelerate up a steep incline or with a loaded trailer in reverse. Wrangler 3.6L Engine (Sales Code ERB) ? Erratic shifting complaints while driving up steep hills or towing during hot ambient temperature conditions. ? Hanging in gear (2nd Gear) when driving up steep hill or Towing (Rubicon ONLY). ? Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). ? Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. ? Delayed Drive to Reverse shift engagement when the transfer case is in Low Range (4LO) - Rubicon Only. Wrangler 2.8L Engine (Sales Code ENS) Erratic while driving in Low Range (4LO). Transmission shifts in

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

The customer may notice that the blower motor speed may slow down at times. This condition will only happen at mid to high ambient temperatures, 75F (24C) or higher. Also the A/C request may be locked on after a remote start. Only after the vehicle is turned off and restarted, will the customer be able to turn the A/C on or off.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

The customer may experience a buzz, squeak or rattle (BSR) at idle speeds.

tube and if necessary installing a protective sleeve on the transmission oil cooler tube. The customer inquires about Recall N28 and power steering return lines are not available, although the vehicle was built on or before February 23, 2013 (MDH 022317) equipped with 3.6L engine (sales code ERB), automatic transmission (sales code DGJ), left hand drive (sales code 5I8).

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

This bulletin involves inspecting the transmission oil cooler tubes, power steering return tube and if necessary installing a protective sleeve on the transmission oil cooler tube. The customer inquires about Recall N28 and power steering return lines are not available, although the vehicle was built on or before February 23, 2013 (MDH 022317) equipped with 3.6L engine (sales code ERB), automatic transmission (sales code DGJ), left hand drive (sales code 5I8).

The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

REPLACING THE HARNESS RETAINER TOWER CLIP. *LJ

(DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Control Module (PCM) with new software. A small number of J8 Vehicles built as over-the-road units for non-reg BUX markets and sold to US-based mining operations with the intent of re-programming the diesel PCM to limit vehicle-speed in the mining environment. The discretion of which mining flash is to be used is left to the discretion of the operator.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Diagnostic Trouble Codes P0407 ? EGR Sensor B Circuit Low, or P0408 ? EGR Sensor B Circuit High Set

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

Control Module (PCM) with new software. A small number of J8 Vehicles built as over-the-road units for non-reg BUX markets and sold to US-based mining operations with the intent of re-programming the diesel PCM to limit vehicle-speed in the mining environment. The discretion of which mining flash is to be used is left to the discretion of the operator.

flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Sensor (SAS).If the diagnostic tests indicate the clockspring/SAS requires replacement, replace the clockspring, upper and lower steering column shrouds and steering wheel back cover. Some customers may experience the illumination of the airbag warning lamp or traction control indicator lamp. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: B1B00 - Driver Airbag Squib 1 Circuit Low. B1B01 - Driver Airbag Squib 1 Circuit High. B1B02 - Driver Airbag Squib 1 Circuit Open. B1B03 - Driver Airbag Squib 1 Circuit Shorted Together. B1B04 - Driver Airbag Squib 2 Circuit Low. B1B05 - Driver Airbag Squib 2 Circuit High. B1B06 - Driver Airbag Squib 2 Circuit Open. B1B07 - Driver Airbag Squib 2 Circuit Shorted Together. C123F - Steering Angle Sensor Comparative Performance. C1219 - Steering Angle Sensor Erratic Performance. C2205 - Steering Angle Sensor Internal. P0579 - Speed Control Multiplexed Switch #1 Performance. P0581 - Speed Control Multiplexed Switch #1 High. P0591 - Speed Control Multiplexed Switch #2 Performance. P0593 - Speed Control Multiplexed Switch #2 High. U1109 - Lost Communication With Lin Steering Wheel Controls.

The customer may experience a no crank, no start condition. Upon further diagnosis the tech may find an active B2204 ECU Configuration Mismatch. This condition may be caused by the vehicle's voltage dropping below 4.5 volts for greater than 200 msec, The WCM will lose information from the EEPROM. Information that may be lost includes key programmed status and immobilizer feature enabled status.

Windshield wiper blade vibration.

following: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE If a connector repair kit is not available on the website contact FCA Redacted Content to see if an alternative repair kit is available for your application prior to ordering the harness. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Windshield wiper blade vibration.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

The customer may describe the security system nuisance alarms with no apparent cause for activation.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs): U0140 Lost Communication With Body Control Module. Attempting to clear the DTC may be unsuccessful. Other enhancements included in this update: Improved fuel pump relay operation. Improved remote start time after key activation. Improved Automatic Shutdown Relay (ASD) timer calibration.

Sensor (SAS).If the diagnostic tests indicate the clockspring/SAS requires replacement, replace the clockspring, upper and lower steering column shrouds and steering wheel back cover. Some customers may experience the illumination of the airbag warning lamp or traction control indicator lamp. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: B1B00 - Driver Airbag Squib 1 Circuit Low. B1B01 - Driver Airbag Squib 1 Circuit High. B1B02 - Driver Airbag Squib 1 Circuit Open. B1B03 - Driver Airbag Squib 1 Circuit Shorted Together. B1B04 - Driver Airbag Squib 2 Circuit Low. B1B05 - Driver Airbag Squib 2 Circuit High. B1B06 - Driver Airbag Squib 2 Circuit Open. B1B07 - Driver Airbag Squib 2 Circuit Shorted Together. C123F - Steering Angle Sensor Comparative Performance. C1219 - Steering Angle Sensor Erratic Performance. C2205 - Steering Angle Sensor Internal. P0579 - Speed Control Multiplexed Switch #1 Performance. P0581 - Speed Control Multiplexed Switch #1 High. P0591 - Speed Control Multiplexed Switch #2 Performance. P0593 - Speed Control Multiplexed Switch #2 High. U1109 - Lost Communication With Lin Steering Wheel Controls.

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

Control Module (PCM) with new software. A small number of J8 Vehicles built as over-the-road units for non-reg BUX markets and sold to US-based mining operations with the intent of re-programming the diesel PCM to limit vehicle-speed in the mining environment. The discretion of which mining flash is to be used is left to the discretion of the operator.

The customer may experience a no crank, no start. Upon further diagnosis active DTCs may be found, B1A25 Invalid Key B1A29 Skim Basestation MIismatch.

This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.

occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality (examples may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the following:~ 1. Power on radio~2. Press MENU H/K~3. Press System Setup S/K~4. Press Manage HDD S/K~5. Press Display Available Space on HDD S/K~6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes~ Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. ~ Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

Windshield wiper blade vibration.

The customer may experience a no crank, no start condition. Upon further diagnosis the tech may find an active B2204 ECU Configuration Mismatch. This condition may be caused by the vehicle's voltage dropping below 4.5 volts for greater than 200 msec, The WCM will lose information from the EEPROM. Information that may be lost includes key programmed status and immobilizer feature enabled status.

The customer may experience a no crank, no start condition. Upon further diagnosis the tech may find an active B2204 ECU Configuration Mismatch. This condition may be caused by the vehicle's voltage dropping below 4.5 volts for greater than 200 msec, The WCM will lose information from the EEPROM. Information that may be lost includes key programmed status and immobilizer feature enabled status.

The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs): **P0456 - EVAP System Small Leak (13 MY only).** U0140 Lost Communication With Body Control Module. Attempting to clear the DTC may be unsuccessful. Other enhancements included in this update: Improved fuel pump relay operation. Improved remote start time after key activation. Improved Automatic Shutdown Relay (ASD) timer calibration.

MODEL 2013 WRANGLER. *PE

REPLACING THE WIPER MODULE LINKAGE BOLT WILL CORRECT THE PROBLEM. *KB

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

The customer may describe a water accumulation condition on the vehicle floor front foot well area.

replacing the tailgate retaining strap. If damaged, it may also be necessary to replace the tailgate hinge covers and/or right side tail lamp as required. The tailgate retaining strap is damaged due to the tailgate hinge over extending. The retaining strap typically breaks at the body side of the retaining strap attachment. Tailgate hinge covers and/or tail lamp may also be damaged as a result of over extension.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

The customer may describe a water accumulation condition on the vehicle floor front foot well area.

2014 units, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply new foam part.~ 2) For 2007 - 2009 units, cut off 8.0 mm from the end that faces the windshield, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply modified foam part.

and hood hinges.

B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)

the rear window zipper in order to adjust and realign the zipper tapes to eliminate zipper skips that can prevent the zipper from disengagement. .1 - Zipper Tapes Aligned Correctly2 - Metal Seperator Pins3 - Misaligned Zipper Tapes4 - Zipper Sliders

and hood hinges.

B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)

A)

- All Dealers

industry awareness regarding the recommended usage of Authentic Mopar Glass.

replacing the tailgate retaining strap. If damaged, it may also be necessary to replace the tailgate hinge covers and/or right side tail lamp as required. The tailgate retaining strap is damaged due to the tailgate hinge over extending. The retaining strap typically breaks at the body side of the retaining strap attachment. Tailgate hinge covers and/or tail lamp may also be damaged as a result of over extension.

there is a single skipped zipper tooth.

2014 units, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply new foam part.~ 2) For 2007 - 2009 units, cut off 8.0 mm from the end that faces the windshield, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply modified foam part.

There is a drain hole along the rear edge of the panel (in car position). After draining the panels, inform the customer of the drain hole and if the issue returns they can drain the panels themselves. Storage of panels outdoors in certain positions will cause water infiltration.~ ~ For a water leak from the center front edge of the Targa Top Panels, do not replace the panels, replace the SEAL, Targa Top (Part Number 68088055AA).

The customer may describe a water accumulation condition on the vehicle floor front foot well area.

replacing the tailgate retaining strap. If damaged, it may also be necessary to replace the tailgate hinge covers and/or right side tail lamp as required. The tailgate retaining strap is damaged due to the tailgate hinge over extending. The retaining strap typically breaks at the body side of the retaining strap attachment. Tailgate hinge covers and/or tail lamp may also be damaged as a result of over extension.

The customer may describe a water accumulation condition on the vehicle floor front foot well area.

replacing the tailgate retaining strap. If damaged, it may also be necessary to replace the tailgate hinge covers and/or right side tail lamp as required. The tailgate retaining strap is damaged due to the tailgate hinge over extending. The retaining strap typically breaks at the body side of the retaining strap attachment. Tailgate hinge covers and/or tail lamp may also be damaged as a result of over extension.

and hood hinges.

frame and A-pillar between the door to close gaps and prevent water leaks. The customer may describe gaps between the windshield frame, door and top of cowl. There may also be a water leak.

CUSTOMER MAY EXPERIENCE WATER ACCUMULATION ON THE FRONT FLOOR AREA. *LJ UPDATED 05/01/15. *LJ

MODEL 2007-2013 WRANGLER. *PE

Control Module (TCM) with new software.

selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: P0830- Clutch Upstop Switch Rationality P0456 - Evap System Small LeakThe correction for Diagnostic Trouble Code P0456 only applies to 2013 Model Year vehicles.

Continuous contact of the aluminum transmission oil cooler tube against the power steering return tube could cause a wear hole in the aluminum transmission oil cooler tube. This can result in a loss of transmission fluid which may damage the transmission and/or a loss of transmission function.

Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ).3.6L Grand Cherokee/Durango Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >58 kph (36 mph) - All Markets. Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer.6.4L Grand Cherokee Poor acceleration or performance above 113 kph (70 mph). Transmission shifting while accelerating from a stop does not meet customers expectation. Harsh shifting during acceleration with moderate accelerator pedal and then lifting off the accelerator pedal. Cannot accelerate up a steep incline or with a loaded trailer in reverse.3.6L Wrangler Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Rubicon Only.2.8L Wrangler Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer. Delayed Drive to Reverse shift engagement when the transfer case is in Low Range (4LO) Transmission shifting while accelerating from a stop does not meet customers expectation. Poor vehicle performance in Drive Poor vehicle performance in Auto Stick Mode. Rubicon Only.3.6L Challenger Transmission shifting does not meet customers expectation while towing a loaded

selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: P0830- Clutch Upstop Switch Rationality P0456 - Evap System Small LeakThe correction for Diagnostic Trouble Code P0456 only applies to 2013 Model Year vehicles.

Continuous contact of the aluminum transmission oil cooler tube against the power steering return tube could cause a wear hole in the aluminum transmission oil cooler tube. This can result in a loss of transmission fluid which may damage the transmission and/or a loss of transmission function.

Squeak noise from under the dash while depressing or releasing the clutch pedal.

Control Module (PCM) with new software. The customer may experience an unwanted cruise control cancelation. Upon further investigation the technician may find P0830 - Clutch Pedal Switch ?A? Circuit.

The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ).3.6L Grand Cherokee/Durango Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >58 kph (36 mph) - All Markets. Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer.6.4L Grand Cherokee. Poor acceleration or performance above 113 kph (70 mph).Transmission shifting while accelerating from a stop does not meet customers expectation. Harsh shifting during acceleration with moderate accelerator pedal and then lifting off the accelerator pedal. Cannot accelerate up a steep incline or with a loaded trailer in reverse.3.6L Wrangler Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Rubicon Only.2.8L Wrangler Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer. Delayed Drive to Reverse shift engagement when the transfer case is in Low Range (4LO) Transmission shifting while accelerating from a stop does not meet customers expectation. Poor vehicle performance in Drive Poor vehicle performance in Auto Stick Mode. Rubicon Only.3.6L Challenger Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F).

selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: P0830- Clutch Upstop Switch Rationality P0456 - Evap System Small LeakThe correction for Diagnostic Trouble Code P0456 only applies to 2013 Model Year vehicles.

2012 and 2013 model year (JK) Jeep Wrangler vehicles. Some of the above vehicles may experience a condition where the power steering return tube contacts the aluminum transmission oil cooler tube. Continuous contact of the aluminum transmission oil cooler tube against the power steering return tube could cause a wear hole in the aluminum transmission oil cooler tube. This can result in a loss of transmission fluid which may damage the transmission and/or a loss of transmission function. Chrysler will conduct a voluntary safety recall on all involved vehicles to replace the power steering return tube and inspect the transmission oil cooler tube for damage. Damaged transmission oil cooler tubes will be replaced. Transmission oil cooler tubes that are not damaged will receive a protective sleeve. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

*CN

*06/03/2014 LJ.

bracket to the front axle and checking alignment settings after repair. The customer may describe a vibration and/or shimmy at a low speed condition.

industry awareness regarding the use of recycled or salvage parts.

Prior to ordering any of the parts (55057300A$, 55057293A$, 55057301A$, 55057294A$) Please contact Micah Straub at cell phone# 248-613-2478 for further instructions. Leave a voice mail and your call will be returned promptly. 5.1 to 7.8 is the correct resistance value although ambient temperature will affect this value. Please call for detailed information. If no return call in 15 minutes, proceed with repair.

industry awareness regarding the use of recycled or salvage parts.

bracket to the front axle and checking alignment settings after repair. The customer may describe a vibration and/or shimmy at a low speed condition.

bracket to the front axle and checking alignment settings after repair. The customer may describe a vibration and/or shimmy at a low speed condition.

Prior to ordering any of the parts (55057300A$, 55057293A$, 55057301A$, 55057294A$) Please contact Micah Straub at cell phone# 248-613-2478 for further instructions. Leave a voice mail and your call will be returned promptly. 5.1 to 7.8 is the correct resistance value although ambient temperature will affect this value. Please call for detailed information. If no return call in 15 minutes, proceed with repair.

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. SYMPTOM/CONDITION FOR RHB RADIOS ONLY: ? Trip planner does not save a route after is was created. ? Route guidance does not activate after the vehicle shuts down. ? Longitude entry does not allow enough digits. ? CD/DVD will not play. ? Navigation accept screen will not clear. ? Navigation shows ?acquiring signal? for an extended period of time. ? New navigation graphics.

The customer may experience one or more of the following. When changing the language on the radio, the navigation may still display English. Help prevent navigation lockup. Ghost image of the vehicle?s brand logo on the display screen. Digital photos loaded onto the hard drive intermittently get lost. Sirius audio pop on power up. HFM audio pop on power up. HFM Mode resume with no information.SYMPTOM/CONDITION FOR RHB RADIOS ONLY: Trip planner does not save a route after is was created. Route guidance does not activate after the vehicle shuts down. Longitude entry does not allow enough digits. CD/DVD will not play. Navigation accept screen will not clear. Navigation shows ?acquiring signal? for an extended period of time. New navigation graphics.

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? CD/DVD will not play (RHB only). ? Navigation accept screen will not clear (RHB only). ? Navigation shows ?acquiring signal? for an extended period of time (RHB only). ? New navigation graphics (RHB only). ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. ? Trip planner does not save a route after is was created (RHB only). ? Route guidance does not activate after the vehicle shuts down (RHB only). ? Longitude entry does not allow enough digits (RHB only).

The customer may experience one or more of the following conditions. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

A customer may experience, no response from or inoperative radio display.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

2013 Start Of Production 7/23/12 to 1/29/13 with heated seats that become inoperative at cold temperatures below 10 degrees.~ Dealers should NOT replace the Heated Seat Module 68138715AA. Dealers should order a new driver and passenger heated seat back pad to correct this issue when the WiTech indicates Diagnostic Trouble Code (DTC) B1092 or B1096. ~ Both driver and passenger HEATED SEAT BACK PAD parts should be replaced even if only one seat exhibits the issue.~ The repair entails removing the seat back trim cover, cutting off the pigtail of the original element and placing the replacement element part over the original part and making the electrical connection

2013 Start Of Production 7/23/12 to 1/29/13 with heated seats that become inoperative at cold temperatures below 10 degrees.~ Dealers should NOT replace the Heated Seat Module 68138715AA. Dealers should order a new driver and passenger heated seat back pad to correct this issue when the WiTech indicates Diagnostic Trouble Code (DTC) B1092 or B1096. ~ Both driver and passenger HEATED SEAT BACK PAD parts should be replaced even if only one seat exhibits the issue.~ The repair entails removing the seat back trim cover, cutting off the pigtail of the original element and placing the replacement element part over the original part and making the electrical connection

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

2013 Start Of Production 7/23/12 to 1/29/13 with heated seats that become inoperative at cold temperatures below 10 degrees.~ Dealers should NOT replace the Heated Seat Module 68138715AA. Dealers should order a new driver and passenger heated seat back pad to correct this issue when the WiTech indicates Diagnostic Trouble Code (DTC) B1092 or B1096. ~ Both driver and passenger HEATED SEAT BACK PAD parts should be replaced even if only one seat exhibits the issue.~ The repair entails removing the seat back trim cover, cutting off the pigtail of the original element and placing the replacement element part over the original part and making the electrical connection

been machined with an incorrect taper during the manufacturing process on about 250 of the above vehicles, with approximately 80 of the axles sold by Mopar aftermarket. This condition can result in premature axle knuckle wear. The aftermarket front axle knuckles must be replaced with new axle knuckles for the left side and right side.

The Customer commnunication requested return of unsold inventory to inpsect for possible incorrect direction threads (right hand rather than left hand). Incorrect direction threads will prevent it from being installed.

been machined with an incorrect taper during the manufacturing process on about 250 of the above vehicles, with approximately 80 of the axles sold by Mopar aftermarket. This condition can result in premature axle knuckle wear. The aftermarket front axle knuckles must be replaced with new axle knuckles for the left side and right side.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

B)