2011 Jeep Wrangler TSBs

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTC): U0140 Lost Communication With Body Control Module. Attempting to clear the DTC may be unsuccessful. Other enhancements included in this update: Improved fuel pump relay operation. Improved remote start time after key activation. Improved Automatic Shutdown Relay (ASD) timer calibration.

Diagnostic Trouble Codes P0407 ? EGR Sensor B Circuit Low, or P0408 ? EGR Sensor B Circuit High Set

flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Customer may experience a condition where the clock will lose over one minute a month.

Sensor (SAS).If the diagnostic tests indicate the clockspring/SAS requires replacement, replace the clockspring, upper and lower steering column shrouds and steering wheel back cover. Some customers may experience the illumination of the airbag warning lamp or traction control indicator lamp. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: B1B00 - Driver Airbag Squib 1 Circuit Low. B1B01 - Driver Airbag Squib 1 Circuit High. B1B02 - Driver Airbag Squib 1 Circuit Open. B1B03 - Driver Airbag Squib 1 Circuit Shorted Together. B1B04 - Driver Airbag Squib 2 Circuit Low. B1B05 - Driver Airbag Squib 2 Circuit High. B1B06 - Driver Airbag Squib 2 Circuit Open. B1B07 - Driver Airbag Squib 2 Circuit Shorted Together. C123F - Steering Angle Sensor Comparative Performance. C1219 - Steering Angle Sensor Erratic Performance. C2205 - Steering Angle Sensor Internal. P0579 - Speed Control Multiplexed Switch #1 Performance. P0581 - Speed Control Multiplexed Switch #1 High. P0591 - Speed Control Multiplexed Switch #2 Performance. P0593 - Speed Control Multiplexed Switch #2 High. U1109 - Lost Communication With Lin Steering Wheel Controls.

2008 through 2012 model year (JK) Jeep Wrangler vehicles equipped with a Right Hand Drive (RHD) steering configuration (sales code AHF) and built for U.S specifications (sales code YAA). Some of the above vehicles may have an airbag system clockspring assembly that could experience a compromised airbag circuit. This condition could result in an airbag warning lamp illumination. Chrysler will conduct a voluntary safety recall on all affected RHD vehicles to replace the airbag system clockspring. Additionally, 2008 through 2010 model year vehicles will receive a steering wheel dust shield. NOTE: Safety Recall L37 which provided an interim repair for this issue is being cancelled. Involved vehicle owners will be sent a second owner notification requesting they have their vehicle repaired. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

Customer may experience a condition where the clock will lose over one minute a month.

following: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE If a connector repair kit is not available on the website contact FCA Redacted Content to see if an alternative repair kit is available for your application prior to ordering the harness. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Customer may experience a condition where the clock will lose over one minute a month.

2008 through 2012 model year (JK) Jeep Wrangler vehicles equipped with a Right Hand Drive (RHD) steering configuration (sales code AHF) and built for U.S specifications (sales code YAA). Some of the above vehicles may have an airbag system clockspring assembly that could experience a compromised airbag circuit. This condition could result in an airbag warning lamp illumination. Chrysler will conduct a voluntary safety recall on all affected RHD vehicles to replace the airbag system clockspring. Additionally, 2008 through 2010 model year vehicles will receive a steering wheel dust shield. NOTE: Safety Recall L37 which provided an interim repair for this issue is being cancelled. Involved vehicle owners will be sent a second owner notification requesting they have their vehicle repaired. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

Customer may experience a condition where the clock will lose over one minute a month.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

The customer may describe the security system nuisance alarms with no apparent cause for activation.

Customer may experience a condition where the clock will lose over one minute a month.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTC): U0140 Lost Communication With Body Control Module. Attempting to clear the DTC may be unsuccessful. Other enhancements included in this update: Improved fuel pump relay operation. Improved remote start time after key activation. Improved Automatic Shutdown Relay (ASD) timer calibration.

The customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTC): U0140 Lost Communication With Body Control Module. Attempting to clear the DTC may be unsuccessful. Other enhancements included in this update: Improved fuel pump relay operation. Improved remote start time after key activation. Improved Automatic Shutdown Relay (ASD) timer calibration.

Sensor (SAS).If the diagnostic tests indicate the clockspring/SAS requires replacement, replace the clockspring, upper and lower steering column shrouds and steering wheel back cover. Some customers may experience the illumination of the airbag warning lamp or traction control indicator lamp. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: B1B00 - Driver Airbag Squib 1 Circuit Low. B1B01 - Driver Airbag Squib 1 Circuit High. B1B02 - Driver Airbag Squib 1 Circuit Open. B1B03 - Driver Airbag Squib 1 Circuit Shorted Together. B1B04 - Driver Airbag Squib 2 Circuit Low. B1B05 - Driver Airbag Squib 2 Circuit High. B1B06 - Driver Airbag Squib 2 Circuit Open. B1B07 - Driver Airbag Squib 2 Circuit Shorted Together. C123F - Steering Angle Sensor Comparative Performance. C1219 - Steering Angle Sensor Erratic Performance. C2205 - Steering Angle Sensor Internal. P0579 - Speed Control Multiplexed Switch #1 Performance. P0581 - Speed Control Multiplexed Switch #1 High. P0591 - Speed Control Multiplexed Switch #2 Performance. P0593 - Speed Control Multiplexed Switch #2 High. U1109 - Lost Communication With Lin Steering Wheel Controls.

occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality (examples may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the following:~ 1. Power on radio~2. Press MENU H/K~3. Press System Setup S/K~4. Press Manage HDD S/K~5. Press Display Available Space on HDD S/K~6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes~ Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. ~ Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.

front heated seat backs and cushion, if needed. The customer may experience an intermittent condition where one or both front heated seat are inoperative. This condition will only occur when temperatures are below 10F/-12C degrees. When temperatures drop, the resistance values of the heated seat circuits will drop below specification and set DTC, B1092 - Front Left Seat Heater Control Circuit Low and/or B1096 - Front Right Seat Heater Control Circuit Low. Once the vehicle warms up the condition will be gone.

2008 through 2012 model year (JK) Jeep Wrangler vehicles equipped with a Right Hand Drive (RHD) steering configuration (sales code AHF) and built for U.S specifications (sales code YAA). Some of the above vehicles may have an airbag system clockspring assembly that could experience a compromised airbag circuit. This condition could result in an airbag warning lamp illumination. Chrysler will conduct a voluntary safety recall on all affected RHD vehicles to replace the airbag system clockspring. Additionally, 2008 through 2010 model year vehicles will receive a steering wheel dust shield. NOTE: Safety Recall L37 which provided an interim repair for this issue is being cancelled. Involved vehicle owners will be sent a second owner notification requesting they have their vehicle repaired. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

Customer may experience a condition where the clock will lose over one minute a month.

THE CUSTOMER MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION OR NOTICE THAT THE FUEL SAVER INDICATOR LIGHT (FSI) IS TURNING ON AND OFF. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND ONE OR MORE OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTCS): **P0452 - EVAP PRESSURE SWITCH STUCK CLOSED (10 MY WITH SALES CODE DEH ONLY).** U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE. ATTEMPTING TO CLEAR THE DTC MAY BE UNSUCCESSFUL. OTHER ENHANCEMENTS INCLUDED IN THIS UPDATE: IMPROVED FUEL PUMP RELAY OPERATION. IMPROVED REMOTE START TIME AFTER KEY ACTIVATION. IMPROVED AUTOMATIC SHUTDOWN RELAY (ASD) TIMER CALIBRATION. FIX FOR FALSE (FSI) LIGHT ON (WITH COMBINATION SALES CODES EGT AND DEH)."

AFTER DETECTION OF DOWNSTREAM OXYGEN SENSOR SLOW RESPONSE MONITOR OR EGR MONITOR FAULT, SOME VEHICLES MAY HAVE BEEN INADVERTENTLY PROGRAMMED WITH SOFTWARE THAT FAIL TO ILLUMINATE THE MIL. *PE

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

The customer may describe a water accumulation condition on the vehicle floor front foot well area.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

The customer may describe a water accumulation condition on the vehicle floor front foot well area.

2014 units, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply new foam part.~ 2) For 2007 - 2009 units, cut off 8.0 mm from the end that faces the windshield, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply modified foam part.

associated with water dripping across the door sill and/or damp front floor. If necessary, procedures for notching the passenger and/or driver side door seals, inspecting along the bottom edge of the door seal channel for possible sealer skips, antenna grommet inspection and passenger side weather strip stuffer repairs are covered. The customer may experience water dripping across the door sill and/or a damp front floor.1 - Front Door Sill (Waterleak)2 - Front Floor3 - Door Panel Front Lower Fastener

and hood hinges.

B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)

the rear window zipper in order to adjust and realign the zipper tapes to eliminate zipper skips that can prevent the zipper from disengagement. .1 - Zipper Tapes Aligned Correctly2 - Metal Seperator Pins3 - Misaligned Zipper Tapes4 - Zipper Sliders

and hood hinges.

B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)

A)

- All Dealers

industry awareness regarding the recommended usage of Authentic Mopar Glass.

there is a single skipped zipper tooth.

2014 units, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply new foam part.~ 2) For 2007 - 2009 units, cut off 8.0 mm from the end that faces the windshield, remove the old foam part, clean rail of any residue, alcohol wipe the surface, apply promoter (if available), and apply modified foam part.

There is a drain hole along the rear edge of the panel (in car position). After draining the panels, inform the customer of the drain hole and if the issue returns they can drain the panels themselves. Storage of panels outdoors in certain positions will cause water infiltration.~ ~ For a water leak from the center front edge of the Targa Top Panels, do not replace the panels, replace the SEAL, Targa Top (Part Number 68088055AA).

associated with water dripping across the door sill and/or damp front floor. If necessary, procedures for notching the passenger and/or driver side door seals, inspecting along the bottom edge of the door seal channel for possible sealer skips, antenna grommet inspection and passenger side weather strip stuffer repairs are covered. The customer may experience water dripping across the door sill and/or a damp front floor.1 - Front Door Sill (Waterleak)2 - Front Floor3 - Door Panel Front Lower Fastener

The customer may describe a water accumulation condition on the vehicle floor front foot well area.

The customer may describe a water accumulation condition on the vehicle floor front foot well area.

associated with water dripping across the door sill and/or damp front floor. If necessary, procedures for notching the passenger and/or driver side door seals, inspecting along the bottom edge of the door seal channel for possible sealer skips, antenna grommet inspection and passenger side weather strip stuffer repairs are covered. The customer may experience water dripping across the door sill and/or a damp front floor.1 - Front Door Sill (Waterleak)2 - Front Floor3 - Door Panel Front Lower Fastener

part for a water leak condition, please refer to Service Bulletin 23-001-12.~ For 2010 JK Only:~ It is not necessary to replace the right side door mounted weatherstrip on hard top units built prior to 11/01/2009 for a windnoise condition. Instead, perform Service Bulletin 23-001-10

and hood hinges.

associated with water dripping across the door sill and/or damp front floor. If necessary, procedures for notching the passenger and/or driver side door seals, inspecting along the bottom edge of the door seal channel for possible sealer skips, antenna grommet inspection and passenger side weather strip stuffer repairs are covered. The customer may experience water dripping across the door sill and/or a damp front floor.1 - Front Door Sill (Waterleak)2 - Front Floor3 - Door Panel Front Lower Fastener

frame and A-pillar between the door to close gaps and prevent water leaks. The customer may describe gaps between the windshield frame, door and top of cowl. There may also be a water leak.

CUSTOMER MAY EXPERIENCE WATER ACCUMULATION ON THE FRONT FLOOR AREA. *LJ UPDATED 05/01/15. *LJ

MODEL 2007-2013 WRANGLER. *PE

MODEL 2007-2012 WRANGLER. *PE

VEHICLE EXPERIENCE PREMATURE WEAR AT ROOF BOWS ON SOFT TOP. *PE

semi and full synthetic oils.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

The customer may experience a buzz, squeak or rattle (BSR) at idle speeds.

The customer may experience a buzz, squeak or rattle (BSR) at idle speeds.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

flag nut to knock it loose from e-coat that has dried it in place.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

The customer may notice that the blower motor speed may slow down at times. This condition will only happen at mid to high ambient temperatures, 75F (24C) or higher. Also the A/C request may be locked on after a remote start. Only after the vehicle is turned off and restarted, will the customer be able to turn the A/C on or off.

The customer may experience a buzz, squeak or rattle (BSR) at idle speeds.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

INFORMATION REGARDING A RECALL, EFFECTING 3.8L ENGINES, FOR PCM REPROGRAMMING THAT MAY NOT RUN DOWNSTREAM OXYGEN SENSOR SLOW RESPONSE MONITOR. *PE

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

been machined with an incorrect taper during the manufacturing process on about 250 of the above vehicles, with approximately 80 of the axles sold by Mopar aftermarket. This condition can result in premature axle knuckle wear. The aftermarket front axle knuckles must be replaced with new axle knuckles for the left side and right side.

The Customer commnunication requested return of unsold inventory to inpsect for possible incorrect direction threads (right hand rather than left hand). Incorrect direction threads will prevent it from being installed.

been machined with an incorrect taper during the manufacturing process on about 250 of the above vehicles, with approximately 80 of the axles sold by Mopar aftermarket. This condition can result in premature axle knuckle wear. The aftermarket front axle knuckles must be replaced with new axle knuckles for the left side and right side.

INFORMATION CENTER (EVIC), FAILS TO FUNCTION INTERMITTENTLY OR NOT AT ALL. *PE

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

The customer may experience one or more of the following conditions. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

A customer may experience, no response from or inoperative radio display.

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

Squeak noise from under the dash while depressing or releasing the clutch pedal.

*KB

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

and Customer Concern (CC) failure codes.

CLOCKSPRING INFORMATION. *RM