2026 Jeep Wagoneer TSBs

HUD cannot be seen in daytime and very dim at night. This bulletin involves inspecting and possibly replacing the HUD module.

function is not operating properly? *Forward/Backward *Recline Forward *Recline Backward *Height Adjustment *Multiple Functions 2.Is the concern constant or Intermittent? 3.If intermittent, how often does it occur? Daily, Weekly, Randomly 4.Does the seat move on its own without pressing any switch? Yes / No 5.Does the issue occur only while driving, only at key-on, or while the vehicle is parked? 6.Has the concern occurred after the vehicle has been sitting for an extended period (overnight or several hours)? 7.Does pressing the switch multiple times temporarily restore operation? 8.Have any other seat functions or electrical features been affected at the same time? 9.Has the seat adjuster switch or seat assembly been previously repaired or replaced? Before replacing the seat adjuster switch, verify power, ground, connector engagement, wiring integrity, and inspect for blown fuses or damaged harnesses. If no external issues are found and the concern is verified, an intermittent internal switch failure should be considered.

indicator in the Instrument Panel Cluster (IPC) blinks ON/OFF at a faster than normal pace. Turn signal lamp blinks but the lighting is not sweeping when activated. Decorative turn signal lamp does not turn on when activated. NOTE: Turn signal operation still meets the regulatory requirements. This bulletin involves inspecting and possibly reprogramming the SLML with the latest software.

gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.

If no applicable TSBs/RSUs, or they have already been applied, please refer to the updated Service Library diagnostic procedure for P1CEA-00-BOOST SIDE EVAP PURGE SYSTEM PERFORMANCE (MODULE, Powertrain Control (PCM), 3.0L GMET6) and SOL S2518000008.

If Ambient Lights can change color and intensity, do not replace Auxiliary/Ambient Lighting Module (ALM). Follow the diagnostic for B2811-02. Before replacing, verify the vehicle PROXI is correct for the vehicle (2-row/3-row). If PROXI is incorrect, re-PROXI and then perform a hard reset of the ALM.

Inoperative, Service Active Lane Management Message, Inside Rearview Mirror Cover and LRCF Windshield Bracket.

Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): B22A9-96 ECU Internal Performance-Component Internal Failure. B1560-11 Cellular Antenna 1 - Short To Ground. B1560-13 Cellular Antenna 1 - Circuit Open. B1561-11 Cellular Antenna 2 - Short To Ground. B1561-13 Cellular Antenna 2 - Circuit Open. B1562-14 GPS Antenna Short To Ground Or Open. Customers may also experience the following: "Uconnect Box Required Service" message in Radio Display This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The TBM software will be updated from R5R to R5T software level.

The heated seats not showing on rear screen Fig. 1 This bulletin involves performing a restore vehicle configuration and Proxi configuration alignment

The Instrument Panel Cluster (IPC) may display "Liftgate Open", a warning light may illuminate even though the liftgate appears fully closed, and an audible chime may be generated at speeds above 8 kph (5 mph). The liftgate cannot be opened using the front interior switch, key fob, Hands Free kick or exterior handle. The power liftgate will not open. The power liftgate system chimes when trying to operate the liftgate using a Hands Free Entry (HFE) kick while no key is detected in the zone. After enabling or disabling the HFE kick or the Power Liftgate Alert feature, the PLGM does not save the changes. Vehicle will not start due to a depleted battery. The power liftgate latch releases after pressing the exterior handle switch, but the liftgate does not power open. This bulletin involves inspecting and possibly reprogramming the PLGM with the latest available software.

Digital Key Control Module Secret Code-Missing Message (and/or) A Cluster Message May Appear Processing Digital Key

C0051-54 Steering Wheel Position Sensor Calibration, C0051-64 Steering Angle Set.

vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): P051B-00 - Crankcase Pressure Sensor Circuit Range/performance. This bulletin involves replacing the clean air duct assembly.

Trouble Code (DTC): SYMPTOM: B12B5-49 - Head Up Display Module-Internal Electronic Failure. Customers may experience the following: Audible ringing noise coming from the instrument panel around the HUD module area when on. s are to be made at this time. Once available, new PN 68613172AG will have the solution. A SW update is not available to the HUD module. POLICY: Information Only.

vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): P051B-00 - Crankcase Pressure Sensor Circuit Range/performance. This bulletin involves replacing the clean air duct assembly.

Trouble Code (DTC): SYMPTOM: B12B5-49 - Head Up Display Module-Internal Electronic Failure. Customers may experience the following: Audible ringing noise coming from the instrument panel around the HUD module area when on. s are to be made at this time. Once available, new PN 68613172AG will have the solution. A SW update is not available to the HUD module. POLICY: Information Only.

illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): B22A9-96 - ECU Internal Performance-Component Internal Failure. B1560-11 - Cellular Antenna 1-Circuit Short To Ground. B1560-13 - Cellular Antenna 1-Circuit Open. B1561-11 - Cellular Antenna 2-Circuit Short To Ground. B1561-13 - Cellular Antenna 2-Circuit Open. B1562-14 - GPS Antenna-Circuit Short To Ground Or Open. The customer may experience the following: Uconnect Box requires service message at start up on the display screen. This bulletin involves reprogramming the TBM with the latest available software.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Verify Battery Voltage: Ensure battery voltage is at nominal value (minimum 12.5 V). Charge the battery, if necessary before proceeding. 2. Confirm Low Voltage DTCs: After charging, verify that any low battery voltage DTCs are stored. 3. Check PLGM Proxi Alignment: 4. If PLGM is not aligned: - Perform Proxi Alignment - Reset the module - Perform module recalibration. 5. If Proxi Is Correct: - Reset the module. - Perform module calibration. 6. Diagnose Active DTCs 7. Inspect wiring and related components associated with those DTCs. Repair as necessary and clear DTCs. 8. Module Replacement: If the module does not accept Proxi alignment, Module reset, or Calibration.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

The Instrument Panel Cluster (IPC) may display "Liftgate Open", a warning light may illuminate even though the liftgate appears fully closed, and an audible chime may be generated at speeds above 8 kph (5 mph). The liftgate cannot be opened using the front interior switch, key fob, Hands Free kick or exterior handle. The power liftgate will not open. The power liftgate system chimes when trying to operate the liftgate using a Hands Free Entry (HFE) kick while no key is detected in the zone. After enabling or disabling the HFE kick or the Power Liftgate Alert feature, the PLGM does not save the changes. Vehicle will not start due to a depleted battery. The power liftgate latch releases after pressing the exterior handle switch, but the liftgate does not power open. This bulletin involves inspecting and possibly reprogramming the PLGM with the latest available software.

Rain Sensor Internal Failure.

Rain Sensor Internal Failure.

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

This can happen during the lifetime of the vehicle. TBM should not be replace for B1E21, since there is no fault on TBM. TBM battery is replaceable. Part number of the back-up battery inside TBM is 68597650AA.

Sensor(s) Not Reading And Or Showing Dashes.

experience one or more of the following: - Error display of "Uconnect Box Requires Service" popups; [ TBM DTCs B1560, B1561, B1562 - Antenna loose connection ]. - TBM sleep mode not working causing battery drain in some cases. - Error display of "Uconnect Box Requires Service/Wifi Unavailable" pop ups; [ TBM DTC B22A9-96 Internal Performance Failure ].

NOTE: Rearview mirror can become detached with minimal force applied. This bulletin involves inspecting the rearview mirror bracket adhesion and possibly replacing the windshield.

Mirror Contacts Door Window Glass In The Folded Position.

This bulletin involves inspecting and possibly replacing one or both front door nameplates.

Mirror Contacts Door Window Glass In The Folded Position.

One or both adjustable hood bumpers are broken. This bulletin involves replacing both hood bumpers.

Mirror Contacts Door Window Glass In The Folded Position.

Driver Master Switch

Mirror Contacts Door Window Glass In The Folded Position.

(DTC) present: SYMPTOM: B251D1-00 - Universal Garage Door Opener Control. Customers may comment on the following: Operational questions regarding the usage of the HomeLink UGDO. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.

Driver Master Switch

chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.

a proper evaluation of the issue. If this does not correct the issue, please follow the steps in SOL: S2508000039

must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): P2797-00 - Auxiliary Transmission Fluid Pump Performance. Customers may also comment on the following: Engine Stop-Start (ESS) does not operate. "Service Transmission" message displayed in the Instrument Panel Cluster (IPC). This bulletin involves inspecting and possibly replacing the transmission oil pump motor.

15,000 of the above vehicles may become disconnected from the intake manifold or the purge solenoid. This condition can cause an engine misfire, rough running and hard starting. In addition, the Malfunction Indicator Lamp (MIL) may illuminate on the instrument panel cluster.

Oil Leak. This bulletin involves replacing the engine oil pan.

Oil Leak. This bulletin involves replacing the engine oil pan.

Motor - Circuit Open / B1DB3-13 - Right Power Side Step Motor - Circuit Open B1DB4-39 - Left Power Side Step Position Sensor - Signal Has Too Few Pulses / B1DB5-39 - Right Power Side Step Position Sensor - Signal Has Too Few Pulses Please do not replace the motors or the module if you're seeing this DTCs coming up Write/record the DTCs in the narrative Please refer to the DTC service manuals available in the Service Library to root cause and repair accordingly

- Engine Systems / Starting / Diagnosis and Testing / STANDARD STARTING SYSTEM. Updates to this procedure have been recently made and should be followed.

Do not replace TBM ECU or SGW. If replacement is determined, Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only. Under certain conditions, SGW Module may take longer to establish Ethernet communication after boot up. If it takes longer than 30 seconds, The TBM2.0H module will set DTC U0080 - Ethernet Bus 1. As soon as SGW responds, the TBM2.0H will demature the DTC and move it to STORED. This issue should not cause any customer related symptoms. Do not replace the following TBM Part Numbers: WL: 68639445AF,68637489AE,68663479AE. WS: 68734941AA,68729188AC. EJ: 68592344AI. KM: 68592343AL,68735975AD. DT: 68634362AJ,68624784AF,68624784AE,68735493AB,68735493AA. DJ (HDCC): 68608721AJ. If the TBM2.0H module has set the DTC U0080 and it is STORED or ACTIVE, please clear the fault and do nothing. No further diagnostics is required. ---------------------------------------------------------------------------------------------------- TBM2.0H Setting DTC B1E21 Do Not Replace the TBM ECU. Is triggered when the TBM Backup Battery is discharged, inactive, or drained. This can happen during the lifetime of the vehicle. TBM should NOT be replace for B1E21, since there is no fault on TBM. TBM battery is replaceable. Part number of the back-up battery inside TBM is 68597650AA. Do not replace the following TBM Part Numbers: WL: 68639445A$, 68663479A$. -------------------------------------------------------------------------------------------------------- TBM Setting DTC U0499-00 Please refer to SOL S268A000004 if you are attempting to replace or repair the telematics box due to DTC U0499-00. This DTC does not cause direct customer impact and cannot be cleared. Engineering is working on TBM software enhancements, tentative Q2 2026. Do not replace the following TBM Part Numbers: KM: 68592343A$

Do not replace TBM ECU or SGW. Under certain conditions, SGW Module may take longer to establish Ethernet communication after boot up. If it takes longer than 30 seconds, The TBM2.0H module will set DTC U0080 - Ethernet Bus 1. As soon as SGW responds, the TBM2.0H will demature the DTC and move it to STORED. This issue should not cause any customer related symptoms. Do not replace the following TBM Part Numbers: WL: 68639445AF,68637489AE,68663479AE. WS: 68734941AA,68729188AC. EJ: 68592344AI. KM: 68592343AL,68735975AD. DT: 68634362AJ,68624784AF,68624784AE,68735493AB,68735493AA. DJ (HDCC): 68608721AJ. If the TBM2.0H module has set the DTC U0080 and it is STORED or ACTIVE, please clear the fault and do nothing. No further diagnostics is required. ---------------------------------------------------------------------------------------------------- TBM2.0H Setting DTC B1E21 Do Not Replace the TBM ECU. Is triggered when the TBM Backup Battery is discharged, inactive, or drained. This can happen during the lifetime of the vehicle. TBM should NOT be replace for B1E21, since there is no fault on TBM. TBM battery is replaceable. Part number of the back-up battery inside TBM is 68597650AA. Do not replace the following TBM Part Numbers: WL: 68639445A$, 68663479A$. ---------------------------------------------------------------------------------------------------------- TBM Setting DTC U0499-00 Please refer to SOL S268A000004 if you are attempting to replace or repair the telematics box due to DTC U0499-00. This DTC does not cause direct customer impact and cannot be cleared. Engineering is working on TBM software enhancements, tentative Q2 2026. Do not replace the following TBM Part Numbers: KM: 68592343A$

confirm the leak persists "09 - Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"

confirm the leak persists "09 - Engine, 3.0L GMET6 / Cooling System / Engine Cooling / Diagnosis and Testing / COOLING SYSTEM LEAKS"

and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: **Oil Level High Warning in the Instrument Panel Cluster (IPC).** Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. Vehicle is not heating up fast enough at freezi

845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

Proper Oil And Fuel or Service Engine See Dealer. The customer may also mention a low power complaint.

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.

Twin Turbo Engine

the power side steps (running boards) deployment and at the beginning and end of retract This bulletin involves cleaning, tightening, applying Loctite 290 and testing both power side steps.

Please refer to the thermostat's MEDIA image.

If no applicable TSBs/RSUs, or they have already been applied, please refer to SOL S2518000008.

load on the Home/Split screen Fig. 1.

Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay

Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay

Traffic Sign Assist Unavailable Service Required message and icon displays on the Instrument Panel Cluster (IPC). This occurs after a remote start and typically at the first start of the day. The Odometer flashes when the traffic alert message is active. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

Detection Lights Stay ON, ADAS Features Disabled. Multiple DTCs Active Or Stored

SYMPTOM:

Shifter.

Feels like the 4WD is active. While moving above 5 kph (3.1 mph) transmission goes into limp mode. This bulletin involves flashing the DTCM to the latest software level.

To repair issue, use the following part numbers and follow the I-sheet instructions for assembly: 68738079AA - HOUSING 68738084AA - CAM 68738085AA - GEAR 68737112AA - PLATE Please note that the part numbers listed here are transfer case components, not full transfer case part numbers.

To repair issue, use the following parts numbers and follow the I-sheet instructions for assembly: 68738079AA - HOUSING 68738084AA - CAM 68738085AA - GEAR 68737112AA - PLATE

feels like the output has been reduced resulting in poor performance in cold temperatures. NOTE: This issue only happens in temperatures that fluctuate between freezing and slightly above. The thawing and refreezing process produces a build up of ice on the cowl baffles. This bulletin involves removing both right and left side rubber flaps from the cowl baffles.

Power surge on USB hub detected Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.

Power surge on USB hub detected Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle

Power surge on USB hub detected Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle

B1A17-00 in The Radio Frequency Hub (RFH)

illumination and the vehicle must exhibit/set at least one of the following Diagnostic Trouble Codes (DTCs): C2203-00 - Current VIN Missing/Mismatch. C008E-00 - ECU Internal Performance. (With Environmental Data Decode Byte: APP_FATAL_ERROR_APP_CONFIGURATION_ERROR_FAULT.) Customers may also comment on one or more of the following: The Instrument Panel Cluster (IPC) is displaying one or more of the following messages: "ACC/FCW Unavailable Service Required". "ACC/FCW Limited Functionality". "Active Lane Management Limited Functionality." "Active Lane Management Unavailable Service Required". "Automatic Emergency Braking (AEB) Limited Service Required". "AEB Unavailable Service Required". "Blindspot Detection Unavailable Service Required" "Blindspot Detection Limited Functionality" Customer states that the ADAS features are disabled This bulletin involves **inspecting and possibly reprogramming** the CADM with the latest available software and possibly performing a Long Range Camera Front (LRCF) calibration

illumination and the vehicle must exhibit/set at least one of the following Diagnostic Trouble Codes (DTCs): C2203-00 - Current VIN Missing/Mismatch. C008E-00 - ECU Internal Performance with Environmental Data Decode Byte: APP_FATAL_ERROR_APP_CONFIGURATION_ERROR_FAULT. Customers may also comment on one or more of the following: The Instrument Panel Cluster (IPC) is displaying one or more of the following messages: "ACC/FCW Unavailable Service Required". "ACC/FCW Limited Functionality". "Active Lane Management Limited Functionality." "Active Lane Management Unavailable Service Required". "Automatic Emergency Braking (AEB) Limited Service Required". "AEB Unavailable Service Required". "Blindspot Detection Unavailable Service Required" "Blindspot Detection Limited Functionality" Customer states that the ADAS features are disabled. This bulletin involves reprogramming of the CADM with the latest available software and possibly performing a Long Range Camera Front (LRCF) calibration

layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order "68" part number for New unsold units only.

Diagnostic Trouble Code (DTC) B1D9B-54- Seat Horizontal Front Stop Not Learned-Missing Calibration