2025 Jeep Renegade TSBs

ENGINE 1.5 GSE T4 MHEV - Malfunction Indication Light (MIL) P0016 Customers must experience a MIL illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P0016 - Crankshaft/camshaft Timing Misalignment - Bank 1 Sensor 1. Check the trouble codes in the Engine Control Unit (ECU). Apply this document if the trouble code as mentioned is set (P0016). Fix Engine Timing and replace the cam-to-cam guide rail (snubber)

Multiple Systems Repair Bundle Campaign Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P1A93-12 - Reversible Alternator : Power Electronics Fault - Motor Mode Out-Of-Action. Customers may also experience one or more of the following: Front seat recliner motor is not working. Ignition does not turn the engine off. Fuel Pump Control Module (FPCM) - MIL ON. Engine cylinder head cover is damaged. Belt Start Generator (BSG) engine is not starting. Front camera collision warning message is displayed on the Instrument Panel Cluster (IPC). Headlamp low beam not working and the lens is stained. Oil leaking from the Air Conditioning (A/C) compressor. This bulletin involves performing multiple inspections based on the listed Customer Symptoms and possibly performing the associated Operations procedure.

Oil Leak Through The Rear Crankshaft Oil Seal (Flywheel Side) Customers may comment on the following: Oil Pressure warning light illuminates. Engine oil is leaking onto the floor beneath the vehicle. This bulletin involves inspecting for oil leaks and if necessary replacing the rear crankshaft oil seal (flywheel side).

Clutch Actuator Cylinder Motor Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P2787-00 Clutch 1 Temperature Too High. P28C7-00 Clutch A Motor Phase U-V-W Performance. P27F3-00 Clutch 2 Temperature Too High. P28D5-00 Clutch B Motor Phase U-V-W Circuit Performance. Customers may experience the following: Transmission warning light on or odd gears unavailable or even gears unavailable or reverse gear unavailable In case of a reported and ascertained fault, check and replace the worn/damaged components, if necessary, according to the Operating Cycle below.

Tensioner Pad Snubber Assembly Issue Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P0016 - Crankshaft/camshaft Timing Misalignment - Bank 1 Sensor 1. Customers may also comment on the following: Engine runs rough This bulletin involves inspecting and possibly replacing the tensioner pad snubber. CLAIMS DATA: Labor Operation No: Labor Description Skill Category Labor Tim

Tensioner Pad Snubber Assembly Issue Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P0016 - Crankshaft/camshaft Timing Misalignment - Bank 1 Sensor 1. Customers may also comment on the following: Engine runs rough This bulletin involves inspecting and possibly replacing the tensioner pad snubber. CLAIMS DATA: Labor Operation No: Labor Description Skill Category Labor Tim

Fuel Injector Leak Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

Fuel Injector Leak Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

Engine Coolant Leak Through Water Pump Cover Customers may experience the following: Coolant is leaking This bulletin involves inspecting and, if necessary, replacing the water pump cover.

Fuel Injector Leak Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

Drivers Monitoring Module Manifold Absolute Pressure (MAP) Sensor Not Installed Properly Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P006D-00 - Barometric Pressure - Inlet Air Pressure Correlation. P012C-00 - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low. P012D-00 - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High. P1189-00 - Inlet Air Pressure Sensor Circuit Low. P1190-00 - Inlet Air Pressure Sensor Circuit High. This bulletin involves measuring the distance between the lower base of the MAP sensor and the surface of the intake air line and, if required, replacing the MAP sensor.

Brake Warning Lamp On Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): C1215-86 - Brake Light Switch - Signal Invalid. Customers may comment on one or more of the following: "ABS" warning displays on the Instrument Panel Cluster (IPC). Excessive force required when depressing the brake pedal when trying to start the engine This bulletin involves inspecting the brake pedal switch pressure and possibly performing a reseating of the brake pedal switch

Brake Warning Lamp On Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): C1215-86 - Brake Light Switch - Signal Invalid. Customers may comment on one or more of the following: "ABS" warning displays on the Instrument Panel Cluster (IPC). Excessive force required when depressing the brake pedal when trying to start the engine. This bulletin involves inspecting the brake pedal switch pressure and possibly performing a reseating of the brake pedal switch

Spark Plug Melting Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0300 -00 - Random/Multiple Cylinder - Misfire Detected. P0301 -00 - Cylinder 1 - Misfire Detected. P0302 -00 - Cylinder 2 - Misfire Detected. P0303 -00 - Cylinder 3 - Misfire Detected. P0304 -00 - Cylinder 4 - Misfire Detected. P1336 -00 - Combustion misfiring (impact on catalytic converter) : Cylinder undetermined. P1337 - Combustion misfiring (impact on catalytic converter) : Cylinder 1. P1338 - Combustion misfiring (impact on catalytic converter) : Cylinder 2. P1339 - Combustion misfiring (impact on catalytic converter) : Cylinder 3. P1340 - Combustion misfiring (impact on catalytic converter) : Cylinder 4. Customers may also experience one or more of the following: Engine makes a loud metallic knocking noise at idle. Difficulty starting. Rough and noisy idle This bulletin involves inspecting for DTCs, inspecting for engine leaks and/or damage, and replacing the spark plugs.

Rear Main Crankshaft Oil Seal Leak Customers may comment on the following: **Oil Pressure warning light illuminates.** Engine oil leak. This bulletin involves inspecting for oil leaks and if necessary replacing the rear main crankshaft oil seal.

Brake Warning Lamp On Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): C1215-86 - Brake Light Switch - Signal Invalid. Customers may comment on one or more of the following: "ABS" warning displays on the Instrument Panel Cluster (IPC). Excessive force required when depressing the brake pedal when trying to start the engine This bulletin involves inspecting the brake pedal switch pressure and possibly performing a reseating of the brake pedal switch

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0032-00 - Comando Do Aquecedor De Sonda Lambda Pr-catalisador - Circuito Alto. P0133-00 - Sonda Lambda Pr-catalisador - Resposta Lenta. P0171-00 - Sonda Lambda Pr-catalisador - Mistura Pobre. Customers may comment on one or more of the following: Engine power loss. Engine acceleration cuts out at times. This bulletin involves possibly replacing the upstream oxygen sensor and reprogramming the PCM with the latest available software.

Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0032-00 - Comando Do Aquecedor De Sonda Lambda Pr-catalisador - Circuito Alto. P0133-00 - Sonda Lambda Pr-catalisador - Resposta Lenta. P0171-00 - Sonda Lambda Pr-catalisador - Mistura Pobre. Customers may comment on one or more of the following: Engine power loss. Engine acceleration cuts out at times This bulletin involves reprogramming the PCM with the latest available software and possibly replacing the upstream oxygen sensor. This bulletin involves reprogramming the PCM with the latest available software and possibly replacing the upstream oxygen sensor.

Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087 - Fuel Rail Pressure Too Low - Bank 1. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P006C - MAP - Turbocharger Inlet Pressure Correlation. Customers may also experience one or more of the following: The injector light is illuminated on the Instrument Panel Cluster (IPC). Engine idle is unstable. Abnormal noise from the engine. This bulletin involves inspecting for a fuel injector leak and possibly replacing the fuel injectors and the fuel pipe

Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTC)s have been set: P012C - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low. P012D - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High. P006C-MAP - Turbocharger Inlet Air Pressure Correlation. "

thermostatic valve This bulletin involves inspecting and, if necessary, replacing the thermostatic valve gasket"

This bulletin involves inspecting and, if necessary, replacing the thermostatic valve gasket."

front right part in the engine area during parking maneuvers when changing gear from R to D, as well as when reversing from D to R. This bulletin involves inspecting the right hand side engine mount and replacing it as needed."

This bulletin involves inspecting and, if necessary, replacing the thermostatic valve gasket."

This bulletin involves inspecting and, if necessary, replacing the thermostatic valve gasket."

following: lAir conditioning provides insufficient cabin cooling. lAir conditioning is inoperative. This bulletin involves performing an inspection and possibly replacing the piping between expansion valve and connection to compressor piping."

This bulletin involves inspecting and possibly replacing the engine starter. "

This bulletin involves inspecting for oil leaks and if necessary replacing the rear main crankshaft oil seal."

This bulletin involves inspecting and possibly replacing the engine starter."

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

Flash: Hybrid Control Processor (HCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P2601 - 00 - Electrtic Coolant Pump Control Circuit Performance/stuck Off This bulletin involves reprogramming the HCP with the latest available software.Flash: Hybrid Control Processor (HCP) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P2601 - 00 - Electrtic Coolant Pump Control Circuit Performance/stuck Off This bulletin involves reprogramming the HCP with the latest available software.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

Rear View Camera Inoperable Customers may experience the following: Rearview camera is inoperable, or shows a blue screen. This bulletin involves replacing the rearview camera main harness.

Front Harness Interference With Battery Support Customers may comment on one or more of the following: Warning light on Instrument Panel Cluster (IPC), with warnings of electric fan faults. Smoke smell. This bulletin involves inspecting for wire harness interference and possibly inserting a corrugated tube, anti- abrasive tape noise, a suppressor plate and, if necessary, repairing the wiring harness.

This bulletin involves inspecting the steering wheel operation for a noise while turning and, if noisy, repositioning the steering wheel wire harness."

Turn Signal Lever End Cap Detached Customers may comment on the following: The end cap on the turn signal lever has detached or is loose This bulletin involves replacing the turn signal lever.

Turn Signal Lever Does Not Cancel Customers may comment on the following: Turn signal lever does not return or cancel This bulletin involves inspecting the turn signal lever and possibly replacing it.

Turn Signal Lever Does Not Cancel Customers may comment on the following: Turn signal lever does not return or cancel. This bulletin involves inspecting the turn signal lever and possibly replacing it.

Turn Signal Lever Does Not Cancel Customers may comment on the following: Turn signal lever does not return or cancel. This bulletin involves inspecting the turn signal lever and possibly replacing it.

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

Center High Mounted Stop Lamp (CHMSL) - Water infiltration Customers may experience the following: Water infiltration in the CHMSL. This bulletin involves inspecting and possibly replacing the CHMSL.

Turn Signal Lever Does Not Cancel Customers may comment on the following: Turn signal lever does not return or cancel. This bulletin involves inspecting the turn signal lever and possibly replacing it.

Turn Signal Lever Does Not Cancel Customers may comment on the following: Turn signal lever does not return or cancel. This bulletin involves inspecting the turn signal lever and possibly replacing it.

assemblies are fogged with a light layer of condensation on the inside of the lenses. "

Low Efficiency Air Conditioning The customer may comment on the following: Air conditioning provides insufficient cabin cooling. This bulletin involves performing an inspection and possibly replacing the evaporator piping to intermediate connection.

Fuel Tank Leaking Customers may experience the following: A fuel leak (leakage at the fuel tank inlet).

involves inspecting and possibly repainting fuel door.

Low Efficiency Air Conditioning The customer may comment on the following: Air conditioning provides insufficient cabin cooling. This bulletin involves performing an inspection and possibly replacing the evaporator piping to intermediate connection.

This bulletin involves installing the left and right fuel tank protection covers. "

involves inspecting, and if necessary, properly connecting the fuel hose quick connects"

involves inspecting, and if necessary, properly connecting the fuel hose quick connects"

Flash: Instrument Panel Cluster (IPC) Updates Customer may comment on the following: Incorrect speed limiter indication on the IPC when the system is set to imperial (mph) This bulletin involves reprogramming the IPC with the latest available software

Glove Box Door Difficult To Close Customers may experience the following: The glove compartment door is difficult to close. This bulletin involves installing a washer spacer stack to correct glove compartment door alignment.

Rear Washer Nozzle Inoperative Customers may comment on the following: Rear window washer is not working. This bulletin involves inspecting and possibly connecting the rear washer nozzle hoses to the washer nozzles.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

Loose Front Door Applique Customers may comment on the following: Loose front door applique. This bulletin involves inspecting and possibly replacing one or both front door appliques.

1 is loose, detaching or deforming. This bulletin involves replacing the liftgate Sahara Badge."

1.5L Transmission Diagnosis Service Solution Customers may experience one or more of the following: SYMPTOM: Transmission warning light on and/or vehicle jerking. Vehicle is not shifting correctly or has no traction. This service bulletin is to provide a diagnostic guide for a transmission warning light on, vehicle jerking, not shifting correctly or no traction symptoms.

1.5L Transmission Diagnosis Service Solution Customers may experience one or more of the following: Transmission warning light on and/or vehicle jerking. Vehicle is not shifting correctly or has no traction This service bulletin is to provide a diagnostic guide for a transmission warning light on, vehicle jerking, not shifting correctly or no traction symptoms.

Vehicle Does Not Operate In Electric Mode And/Or Reverse Gear Is Unavailable Customers may experience one or more of the following: The vehicle does not operate in electric mode. Reverse gear is not available.

Vehicle Does Not Operate In Electric Mode And/Or Reverse Gear Is Unavailable Customers may experience one or more of the following: The vehicle does not operate in electric mode. Reverse gear is not available.

Paddle Shift Inoperative Customers may comment on the following: The steering wheel paddle shift feature is inoperative. This bulletin involves inspecting the steering wheel and, if necessary, replacing it

R1L Radio Over The Air Update From 62.00.23 To 62.00.29 Software Version Customers will not experience any symptoms. New software has been created to support a new radio model This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software for will be updated from 62.00.23 to 62.00.29.

message displayed on the multimedia screen.

and/or grid line that is not working Fig. 1. This bulletin involves inspecting the RVC for errors and possibly replacing the RVC."

and/or grid line that is not working Fig. 1. This bulletin involves inspecting the RVC for errors and possibly replacing the RVC."

Brake Booster Noise While Braking Customers may comment on the following: Hissing or air leak type noise heard when braking. This bulletin involves replacing the brake booster.Brake Booster Noise While Braking Customers may comment on the following: Hissing or air leak type noise heard when braking. This bulletin involves replacing the brake booster.Brake Booster Noise While Braking Customers may comment on the following: Hissing or air leak type noise heard when braking. This bulletin involves replacing the brake booster.

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): C170C-00 - PBC (Event PBC Factory Mode). C1436-86 - Electric Parking Brake System Fail. C10D0 - Electronic Park Brake System Failure. Customers may experience one or more of the following: Vehicle does not accelerate properly. Anti-Lock Brakes System (ABS) warning light on. This bulletin involves replacing the ABS Modul

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): C170C-00 - PBC (Event PBC Factory Mode). C1436-86 - Electric Parking Brake System Fail. C10D0 - Electronic Park Brake System Failure. Customers may experience one or more of the following: Vehicle does not accelerate properly. Anti-Lock Brakes System (ABS) warning light on. This bulletin involves replacing the ABS Module."

Order the "R" part number for all orders:

This bulletin involves removing the passenger seat and tightening the fasteners that join the seatback to the seat"

This bulletin involves removing the passenger seat and tightening the fasteners that join the seatback to the seat"

following: A/C system provides insufficient cabin cooling. Low A/C system pressure. Lack or loss of refrigerant in the A/C system. This bulletin involves performing an inspection and possibly replacing A/C lines."