2024 Jeep Renegade TSBs

ENGINE 1.5 GSE T4 MHEV - Malfunction Indication Light (MIL) P0016 Customers must experience a MIL illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P0016 - Crankshaft/camshaft Timing Misalignment - Bank 1 Sensor 1. Check the trouble codes in the Engine Control Unit (ECU). Apply this document if the trouble code as mentioned is set (P0016). Fix Engine Timing and replace the cam-to-cam guide rail (snubber)

Clutch Actuator Cylinder Motor Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P2787-00 Clutch 1 Temperature Too High. P28C7-00 Clutch A Motor Phase U-V-W Performance. P27F3-00 Clutch 2 Temperature Too High. P28D5-00 Clutch B Motor Phase U-V-W Circuit Performance. Customers may experience the following: Transmission warning light on or odd gears unavailable or even gears unavailable or reverse gear unavailable In case of a reported and ascertained fault, check and replace the worn/damaged components, if necessary, according to the Operating Cycle below.

Fuel Injector Leak Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

Fuel Injector Leak Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

Fuel Injector Leak Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

Drivers Monitoring Module Manifold Absolute Pressure (MAP) Sensor Not Installed Properly Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P006D-00 - Barometric Pressure - Inlet Air Pressure Correlation. P012C-00 - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low. P012D-00 - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High. P1189-00 - Inlet Air Pressure Sensor Circuit Low. P1190-00 - Inlet Air Pressure Sensor Circuit High. This bulletin involves measuring the distance between the lower base of the MAP sensor and the surface of the intake air line and, if required, replacing the MAP sensor.

Spark Plug Melting Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0300 -00 - Random/Multiple Cylinder - Misfire Detected. P0301 -00 - Cylinder 1 - Misfire Detected. P0302 -00 - Cylinder 2 - Misfire Detected. P0303 -00 - Cylinder 3 - Misfire Detected. P0304 -00 - Cylinder 4 - Misfire Detected. P1336 -00 - Combustion misfiring (impact on catalytic converter) : Cylinder undetermined. P1337 - Combustion misfiring (impact on catalytic converter) : Cylinder 1. P1338 - Combustion misfiring (impact on catalytic converter) : Cylinder 2. P1339 - Combustion misfiring (impact on catalytic converter) : Cylinder 3. P1340 - Combustion misfiring (impact on catalytic converter) : Cylinder 4. Customers may also experience one or more of the following: Engine makes a loud metallic knocking noise at idle. Difficulty starting. Rough and noisy idle This bulletin involves inspecting for DTCs, inspecting for engine leaks and/or damage, and replacing the spark plugs.

Rear Main Crankshaft Oil Seal Leak Customers may comment on the following: **Oil Pressure warning light illuminates.** Engine oil leak. This bulletin involves inspecting for oil leaks and if necessary replacing the rear main crankshaft oil seal.

Low Oil Pressure Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may also comment on the following: Vehicle will not be able to exceed 3,300 RPM (when DTC P06DD is active) This bulletin involves inspecting and if necessary replacing the timing chain cover (oil pump).

Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087 - Fuel Rail Pressure Too Low - Bank 1. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P006C - MAP - Turbocharger Inlet Pressure Correlation. Customers may also experience one or more of the following: The injector light is illuminated on the Instrument Panel Cluster (IPC). Engine idle is unstable. Abnormal noise from the engine. This bulletin involves inspecting for a fuel injector leak and possibly replacing the fuel injectors and the fuel pipe

Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTC)s have been set: P012C - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low. P012D - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High. P006C-MAP - Turbocharger Inlet Air Pressure Correlation. "

thermostatic valve This bulletin involves inspecting and, if necessary, replacing the thermostatic valve gasket"

This bulletin involves replacing one or both of the rear shock absorbers."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise. This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

This bulletin involves inspecting and, if necessary, replacing the thermostatic valve gasket."

front right part in the engine area during parking maneuvers when changing gear from R to D, as well as when reversing from D to R. This bulletin involves inspecting the right hand side engine mount and replacing it as needed."

This bulletin involves inspecting and, if necessary, replacing the thermostatic valve gasket."

This bulletin involves inspecting and, if necessary, replacing the thermostatic valve gasket."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise. This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube."

following: Oil leaks from the engine compartment, engine/transmission coupling. This bulletin supersedes Technical Service Bulletin (TSB) 09-021-24, date of issue November 23, 2024, which should be removed from your files. All revisions are highlighted with **asterisks** and include new Labor Times."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087 - Sensor De Presso Da Linha De Combustvel - Banco 1 - Presso Abaixo Do Limite P0088 - Sensor De Presso Da Linha De Combustvel - Banco 1 - Presso Acima Do Limite P0089 - Sensor De Presso Da Linha De Combustvel 1 - Desempenho Customers may also comment on one or more of the following: The engine is running rough. Partial loss of engine power. This bulletin involves replacing the high pressure fuel pump."

following: Oil leaks from the engine compartment, engine/transmission coupling. When the claimed fault is confirmed, replace the engine valley cap, according to the Repair Procedure"

This bulletin involves inspecting and possibly replacing the engine starter. "

Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P0C74 - Motor Electronics Coolant Pump ""B"" Control Performance. This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software."

This bulletin involves inspecting for oil leaks and if necessary replacing the rear main crankshaft oil seal."

This bulletin involves inspecting and possibly replacing the engine starter."

This bulletin involves inspecting and possibly replacing the driver side window motor / carrier assembly

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may also comment on the following: ? Vehicle will not be able to exceed 3,300 RPM (when DTC P06DD is active). This bulletin involves inspecting and if necessary replacing the timing chain cover (oil pump).

vehicle forward and reverse This bulletin involves inspecting and if needed replacing the right engine insulator.

This bulletin involves inspecting and possibly replacing the driver side window motor / carrier assembly.

This bulletin involves inspecting and possibly replacing the driver side window motor / carrier assembly

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may also comment on the following: ? Vehicle will not be able to exceed 3,300 RPM (when DTC P06DD is active). This bulletin involves inspecting and if necessary replacing the timing chain cover (oil pump).

after replacing ORC DTCs: B12C7, B12C8 The security gateway module software requires updating with the ORC/Half replacement.

a warning light after replacing ORC Secure gateway software update needed in case Of ORC/Half replacement.

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

Rear View Camera Inoperable Customers may experience the following: Rearview camera is inoperable, or shows a blue screen. This bulletin involves replacing the rearview camera main harness.

illuminated on the Instrument Panel Cluster (IPC). Vehicle does not start due to a depleted battery. This bulletin involves tightening the alternator B+ cable nut to the proper torque specification."

illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P2601-00 - Electric Coolant Pump Control Circuit Performance/Stuck Off. his bulletin involves replacing the auxiliary coolant pump and the pump inlet pipe"

"

This bulletin involves inspecting the steering wheel operation for a noise while turning and, if noisy, repositioning the steering wheel wire harness."

This bulletin involves inspecting the steering wheel operation for a noise while turning and, if noisy, repositioning the steering wheel wire harness."

experience any symptoms.

notification on customers mobile application."

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? P0087 - Fuel Rail Pressure Too Low - Bank 1. ? P0088 - Fuel Rail Pressure Too High - Bank 1. This bulletin involves reprogramming the PCM with the latest available software.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Turn Signal Lever End Cap Detached Customers may comment on the following: The end cap on the turn signal lever has detached or is loose This bulletin involves replacing the turn signal lever.

Turn Signal Lever Does Not Cancel Customers may comment on the following: Turn signal lever does not return or cancel This bulletin involves inspecting the turn signal lever and possibly replacing it.

Turn Signal Lever Does Not Cancel Customers may comment on the following: Turn signal lever does not return or cancel. This bulletin involves inspecting the turn signal lever and possibly replacing it.

Turn Signal Lever Does Not Cancel Customers may comment on the following: Turn signal lever does not return or cancel. This bulletin involves inspecting the turn signal lever and possibly replacing it.

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

Possible DTCs P2453, P2455, P2461.

Center High Mounted Stop Lamp (CHMSL) - Water infiltration Customers may experience the following: Water infiltration in the CHMSL. This bulletin involves inspecting and possibly replacing the CHMSL.

Turn Signal Lever Does Not Cancel Customers may comment on the following: Turn signal lever does not return or cancel. This bulletin involves inspecting the turn signal lever and possibly replacing it.

Turn Signal Lever Does Not Cancel Customers may comment on the following: Turn signal lever does not return or cancel. This bulletin involves inspecting the turn signal lever and possibly replacing it.

assemblies are fogged with a light layer of condensation on the inside of the lenses. "

This bulletin involves testing and possibly replacing the CHMSL if water is present inside."

assemblies are fogged with a light layer of condensation on the inside of the lenses."

assemblies are fogged with a light layer of condensation on the inside of the lenses.

Flash: Instrument Panel Cluster (IPC) Updates Customer may comment on the following: Incorrect speed limiter indication on the IPC when the system is set to imperial (mph) This bulletin involves reprogramming the IPC with the latest available software

Rear Doors Misaligned Customers may comment on the following: Rear doors misaligned with the fixed windows. This bulletin involves adjusting the rear door strikers.

Glove Box Door Difficult To Close Customers may experience the following: The glove compartment door is difficult to close. This bulletin involves installing a washer spacer stack to correct glove compartment door alignment.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

doors is loose or detaching This bulletin involves possibly replacing one or both of the rear door sill moldings (belt moldings)."

1 is loose, detaching or deforming. This bulletin involves replacing the liftgate Sahara Badge."

1. This bulletin involves replacing the left rear door panel. "

1. This bulletin involves replacing the left rear door panel."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

This bulletin involves inspecting and, if necessary, replacing one or both the front wiper arms and wiper blades.

R1L Radio Over The Air Update From 62.00.23 To 62.00.29 Software Version Customers will not experience any symptoms. New software has been created to support a new radio model This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software for will be updated from 62.00.23 to 62.00.29.

message displayed on the multimedia screen.

and/or grid line that is not working Fig. 1. This bulletin involves inspecting the RVC for errors and possibly replacing the RVC."

and/or grid line that is not working Fig. 1. This bulletin involves inspecting the RVC for errors and possibly replacing the RVC."

and/or grid line that is not working Fig. 1. This bulletin involves inspecting the RVC for errors and possibly replacing the RVC."

Fuel Tank Leaking Customers may experience the following: A fuel leak (leakage at the fuel tank inlet).

Fuel Tank Hatch Stuck Closed Customers may experience the following: The fuel tank cap hatch does not open. This bulletin involves replacing the fuel tank hatch.

involves inspecting, and if necessary, properly connecting the fuel hose quick connects"

involves inspecting, and if necessary, properly connecting the fuel hose quick connects"

Fuel odor detected. This bulletin involves inspecting, and if necessary, properly connecting the fuel hose quick connects."

? A/C is not blowing cold. This bulletin involves performing an inspection on and possibly replacing the evaporator.

Order the "R" part number for all orders:

Rear spoiler is loose. This bulletin involves installing a new spoiler"

This bulletin involves removing the passenger seat and tightening the fasteners that join the seatback to the seat"

This bulletin involves replacing both rear dampers. "

this is normal and not a defect.

If the block machining is not complete according to information in SOL, a new long block will need to be ordered.

The purpose of this informative Technical Service Bulletin (TSB) is to support the Network on the following topics: Discern the different kinds of connected service issues (onboard / offboard). Support the customer in his journey to open a request via Customer Care. Address on the correct actions to properly manage a customer complaining about the received assistance."

1.5L Transmission Diagnosis Service Solution Customers may experience one or more of the following: SYMPTOM: Transmission warning light on and/or vehicle jerking. Vehicle is not shifting correctly or has no traction. This service bulletin is to provide a diagnostic guide for a transmission warning light on, vehicle jerking, not shifting correctly or no traction symptoms.

1.5L Transmission Diagnosis Service Solution Customers may experience one or more of the following: Transmission warning light on and/or vehicle jerking. Vehicle is not shifting correctly or has no traction This service bulletin is to provide a diagnostic guide for a transmission warning light on, vehicle jerking, not shifting correctly or no traction symptoms.

Vehicle Does Not Operate In Electric Mode And/Or Reverse Gear Is Unavailable Customers may experience one or more of the following: The vehicle does not operate in electric mode. Reverse gear is not available.

Vehicle Does Not Operate In Electric Mode And/Or Reverse Gear Is Unavailable Customers may experience one or more of the following: The vehicle does not operate in electric mode. Reverse gear is not available.

Brake Booster Noise While Braking Customers may comment on the following: Hissing or air leak type noise heard when braking. This bulletin involves replacing the brake booster.Brake Booster Noise While Braking Customers may comment on the following: Hissing or air leak type noise heard when braking. This bulletin involves replacing the brake booster.Brake Booster Noise While Braking Customers may comment on the following: Hissing or air leak type noise heard when braking. This bulletin involves replacing the brake booster.

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): C170C-00 - PBC (Event PBC Factory Mode). C1436-86 - Electric Parking Brake System Fail. C10D0 - Electronic Park Brake System Failure. Customers may experience one or more of the following: Vehicle does not accelerate properly. Anti-Lock Brakes System (ABS) warning light on. This bulletin involves replacing the ABS Modul

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): C170C-00 - PBC (Event PBC Factory Mode). C1436-86 - Electric Parking Brake System Fail. C10D0 - Electronic Park Brake System Failure. Customers may experience one or more of the following: Vehicle does not accelerate properly. Anti-Lock Brakes System (ABS) warning light on. This bulletin involves replacing the ABS Module."

following: A/C system provides insufficient cabin cooling. Low A/C system pressure. Lack or loss of refrigerant in the A/C system. This bulletin involves performing an inspection and possibly replacing A/C lines."

This bulletin involves replacing the right rear wheel bearing.

This bulletin involves re-centering the steering wheel.

B)