2022 Jeep Renegade TSBs

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

Rear View Camera Inoperable Customers may experience the following: Rearview camera is inoperable, or shows a blue screen. This bulletin involves replacing the rearview camera main harness.

illumination and the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P2601-00 - Electric Coolant Pump Control Circuit Performance/Stuck Off. his bulletin involves replacing the auxiliary coolant pump and the pump inlet pipe"

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

"

experience any symptoms.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

notification on customers mobile application."

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs) have been set: ? B1053-64 RFHM (KIN Communication) - Signal Plausibility Failure ? B1A7D-2F- Start Button-Signal Erratic Customers may also experience: ? Vehicle can not be switched off using the keyless button. This bulletin involves updating the RFHM module with the latest available software.

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? B1006-49 HALF (Haptic Lane Feedback) - Internal Electronic Failure. Customer may also comment on one or more of the following: ? Assistant alert light on the Instrument Panel Cluster (IPC). ? Automatic headlight warning light on the IPC. ? ?Automatic headlamps not available? message on the IPC. ? ?Forward Collision Alert (FCW) not available? message on the IPC. ? ?Lane assist not available? message on the IPC. This bulletin involves replacing the FFCM if required.

? Outdated vehicle data on customer's mobile app. ? Connected Services maintenance popup displayed on the radio screen. ? Connected Services battery maintenance popup displayed on the radio screen. This bulletin involves reprogramming the Global Telematics Box Module with the latest available software.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? /B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? **C008E-00 - ECU Internal Performance.** ? B1006-49 HALF (Haptic Lane Feedback) - Internal Electronic Failure. Customer may also comment on one or more of the following: ? Assistant alert light on the Instrument Panel Cluster (IPC). ? Automatic headlight warning light on the IPC. ? ?Automatic head lamps not available? message on the IPC. ? ?Forward Collision Alert (FCW) not available? message on the IPC. 3? ?Lane assist not available?message on the IPC. This bulletin involves replacing the FFCM if required.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTC)s have been set: ? B1053-64 RFHM (KIN Communication) - Signal Plausibility Failure ? B1A7D-2F- Start Button-Signal Erratic Customers may also experience: ? Vehicle can not be switched off using the keyless button. This bulletin involves updating the RFHM module with the latest available software.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs) have been set: ? B1053-64 RFHM (KIN Communication) - Signal Plausibility Failure ? B1A7D-2F- Start Button-Signal Erratic Customers may also experience: ? Vehicle can not be switched off using the keyless button. This bulletin involves updating the RFHM module with the latest available software.

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? B1006-49 HALF (Haptic Lane Feedback) - Internal Electronic Failure. Customer may also comment on one or more of the following: ? Assistant alert light on the Instrument Panel Cluster (IPC). ? Automatic headlight warning light on the IPC. ? ?Automatic headlamps not available? message on the IPC. ? ?Forward Collision Alert (FCW) not available? message on the IPC. ? ?Lane assist not available? message on the IPC. This bulletin involves replacing the FFCM if required.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

This bulletin involves inspecting the software level and updating the software to: B1 - 47.00.15 M1 - 45.06.06 H1 - 47.00.16

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. Estimated National launch date for 1st FOTA update is expected on 07/22/2022. 2nd FOTA 1-2 weeks after 1st FOTA completes: 1st step from 3.8i to 3.8j2+ and 2nd step 3.8j2+ to 4.30. No dealership visit required, send 2 step TBM updates over the air. Customers may experience one or more of the following: Message displayed on the radio screen, "Uconnect Box requires service. Please visit an authorized dealer."Fig.1. Error Message Remote operation is not working. If the vehicle?s ignition is off state more than 7 days and less than 21 days, Remote ops do not work. Vehicle info is not working (or vehicle info is not giving correct information). Vehicle finder is not working.

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. Estimated National launch date for 1st FOTA update is expected on 07/22/2022. 2nd FOTA 1-2 weeks after 1st FOTA completes: 1st step from 3.8i to 3.8j2+ and 2nd step 3.8j2+ to 4.30. No dealership visit required, send 2 step TBM updates over the air. Customers may experience one or more of the following: Message displayed on the radio screen, "Uconnect Box requires service. Please visit an authorized dealer."Fig.1. Error Message Remote operation is not working. If the vehicle?s ignition is off state more than 7 days and less than 21 days, Remote ops do not work. Vehicle info is not working (or vehicle info is not giving correct information). Vehicle finder is not working.

must be followed for BEV/Hybrid vehicles that are on display at dealership showrooms.

Fuel Injector Leak Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

Fuel Injector Leak Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

Fuel Injector Leak Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

Drivers Monitoring Module Manifold Absolute Pressure (MAP) Sensor Not Installed Properly Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P006D-00 - Barometric Pressure - Inlet Air Pressure Correlation. P012C-00 - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low. P012D-00 - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High. P1189-00 - Inlet Air Pressure Sensor Circuit Low. P1190-00 - Inlet Air Pressure Sensor Circuit High. This bulletin involves measuring the distance between the lower base of the MAP sensor and the surface of the intake air line and, if required, replacing the MAP sensor.

Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.

Spark Plug Melting Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0300 -00 - Random/Multiple Cylinder - Misfire Detected. P0301 -00 - Cylinder 1 - Misfire Detected. P0302 -00 - Cylinder 2 - Misfire Detected. P0303 -00 - Cylinder 3 - Misfire Detected. P0304 -00 - Cylinder 4 - Misfire Detected. P1336 -00 - Combustion misfiring (impact on catalytic converter) : Cylinder undetermined. P1337 - Combustion misfiring (impact on catalytic converter) : Cylinder 1. P1338 - Combustion misfiring (impact on catalytic converter) : Cylinder 2. P1339 - Combustion misfiring (impact on catalytic converter) : Cylinder 3. P1340 - Combustion misfiring (impact on catalytic converter) : Cylinder 4. Customers may also experience one or more of the following: Engine makes a loud metallic knocking noise at idle. Difficulty starting. Rough and noisy idle This bulletin involves inspecting for DTCs, inspecting for engine leaks and/or damage, and replacing the spark plugs.

Low Oil Pressure Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may also comment on the following: Vehicle will not be able to exceed 3,300 RPM (when DTC P06DD is active) This bulletin involves inspecting and if necessary replacing the timing chain cover (oil pump).

Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTC)s have been set: P012C - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low. P012D - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High. P006C-MAP - Turbocharger Inlet Air Pressure Correlation. "

This bulletin involves replacing one or both of the rear shock absorbers."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise. This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube.

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087-00 - Fuel Line Pressure Sensor - Bank 1 - Pressure Below Limit. P0300-00 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P006C-00 - Air Pressure and Temperature Sensor - Correlation. Customers may also comment on one or more of the following: Unstable idle. Abnormal engine noise. This bulletin involves diagnosing and possibly replacing the fuel injectors and the high pressure tube."

following: Oil leaks from the engine compartment, engine/transmission coupling. This bulletin supersedes Technical Service Bulletin (TSB) 09-021-24, date of issue November 23, 2024, which should be removed from your files. All revisions are highlighted with **asterisks** and include new Labor Times."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0087 - Sensor De Presso Da Linha De Combustvel - Banco 1 - Presso Abaixo Do Limite P0088 - Sensor De Presso Da Linha De Combustvel - Banco 1 - Presso Acima Do Limite P0089 - Sensor De Presso Da Linha De Combustvel 1 - Desempenho Customers may also comment on one or more of the following: The engine is running rough. Partial loss of engine power. This bulletin involves replacing the high pressure fuel pump."

following: Oil leaks from the engine compartment, engine/transmission coupling. When the claimed fault is confirmed, replace the engine valley cap, according to the Repair Procedure"

Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section ""System Operation - Smart Charging System"". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC."

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may also comment on the following: ? vehicle will not be able to exceed 3,300 RPM (when DTC P06DD is active). This bulletin involves inspecting and if necessary replacing the timing chain cover (oil pump).

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may also comment on the following: ? Vehicle will not be able to exceed 3,300 RPM (when DTC P06DD is active). This bulletin involves inspecting and if necessary replacing the timing chain cover (oil pump).

vehicle forward and reverse This bulletin involves inspecting and if needed replacing the right engine insulator.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? U0100-00 - Lost Communication with Engine Control Module (ECM). ? U1701-87 - Engine Control Module (ECM) - Missing message. Customer may also experience: ? Vehicle no start condition. This bulletin involves replacement of the PCM for a possible no start condition.

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may also comment on the following: ? Vehicle will not be able to exceed 3,300 RPM (when DTC P06DD is active). This bulletin involves inspecting and if necessary replacing the timing chain cover (oil pump).

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may also comment on the following: ? Vehicle will not be able to exceed 3,300 RPM (when DTC P06DD is active). This bulletin involves inspecting and if necessary replacing the timing chain cover (oil pump).

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? P06DD - Engine Oil Pressure Control Circuit Stuck Off. Customers may also comment on the following: ? vehicle will not be able to exceed 3,300 RPM (when DTC P06DD is active). This bulletin involves inspecting and if necessary replacing the timing chain cover (oil pump).

installed in the vehicle.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Rear Doors Misaligned Customers may comment on the following: Rear doors misaligned with the fixed windows. This bulletin involves adjusting the rear door strikers.

Glove Box Door Difficult To Close Customers may experience the following: The glove compartment door is difficult to close. This bulletin involves installing a washer spacer stack to correct glove compartment door alignment.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

doors is loose or detaching This bulletin involves possibly replacing one or both of the rear door sill moldings (belt moldings)."

This bulletin involves replacing the power folding mirror/window switch assembly."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

involves installation of the missing underbody panel.

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

This bulletin involves installing missing door molding.

1. This bulletin involves replacing the window seal and glass.

This bulletin involves inspecting and, if necessary, replacing one or both the front wiper arms and wiper blades.

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

This bulletin involves installing missing door molding.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

R1L Radio Over The Air Update From 62.00.23 To 62.00.29 Software Version Customers will not experience any symptoms. New software has been created to support a new radio model This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software for will be updated from 62.00.23 to 62.00.29.

following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.82F to QR40.12. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.

? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.5 to QR40.11. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.

Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.2 to QR40.11. NOTE: National launch for this FOTA update is expected to begin February 19, 2023.

? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from Q339.3 to QR39.62. NOTE: The National launch for this FOTA update campaign is expected to begin December 04, 2023.

? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.

FCW Warning Light ON, DTC C14A5-68, C14A5-97

following symptoms: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.6 to QR40.12. NOTE: National launch for this FOTA update is expected to begin November 06, 2023.

? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.62 and QR39.57 to QR40.12. NOTE: National launch for this FOTA update is expected to begin August 16, 2023

? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.

FCW Warning Light ON, DTC C14A5-68, C14A5-97

Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.

Customers may experience: Amplifier inoperative intermittently or distorted sound; no audio message.

Order the "R" part number for all orders:

Rear spoiler is loose. This bulletin involves installing a new spoiler"

this is normal and not a defect.

C0604- Active Air Dam Control Performance

semi and full synthetic oils.

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

Possible DTCs P2453, P2455, P2461.

assemblies are fogged with a light layer of condensation on the inside of the lenses. "

assemblies are fogged with a light layer of condensation on the inside of the lenses."

assemblies are fogged with a light layer of condensation on the inside of the lenses.

assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.

assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.

The purpose of this informative Technical Service Bulletin (TSB) is to support the Network on the following topics: Discern the different kinds of connected service issues (onboard / offboard). Support the customer in his journey to open a request via Customer Care. Address on the correct actions to properly manage a customer complaining about the received assistance."

Library for specifications so a suitable alternative can be used

immediate service when there is not actually a vehicle issue.

This bulletin involves re-centering the steering wheel.

This bulletin involves re-centering the steering wheel.

This bulletin involves re-centering the steering wheel.

The customer may describe the following: Outer tie rod ball and socket noise. Noise noticed during steering wheel rotation after vehicle mileage between 1,000 km (621 miles) and 3,000 km (1,864 miles) and when the tie rodsachieve a temperature greater than 60 C (140 F).

Fuel Tank Hatch Stuck Closed Customers may experience the following: The fuel tank cap hatch does not open. This bulletin involves replacing the fuel tank hatch.

The customer may describe the following: Clunk in front suspension when driving.

No further parts distribution will be taking place. All distributed parts would cover all sold and unsold needs. Please use all stock that your dealer has before asking for parts assistance. If part assistance is still required, please provide the following information to your Area Manager for review: 1. Dealer Code 2. Last eight digits of VIN 3. Appointment date/vehicle VOR at dealer Thank you, Mopar

Sporadically Electronic Parking Brake (EPB) setting is lost. Sporadically Rearview Camera (RVC) image is kept active in forward driving. (Valid for all markets except North America). Sporadically Wireless disconnects and reconnects while TomTom connected services are working (traffic info, weather) and a native navigation route is set while Wireless is streaming music. **This bulletin involves updating the software via USB to 23.04.17.01.** "

B)