2021 Jeep Renegade TSBs

R1L Radio Over The Air Update From 62.00.23 To 62.00.29 Software Version Customers will not experience any symptoms. New software has been created to support a new radio model This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software for will be updated from 62.00.23 to 62.00.29.

following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.82F to QR40.12. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.

? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.5 to QR40.11. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.

Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.2 to QR40.11. NOTE: National launch for this FOTA update is expected to begin February 19, 2023.

? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from Q339.3 to QR39.62. NOTE: The National launch for this FOTA update campaign is expected to begin December 04, 2023.

? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.

FCW Warning Light ON, DTC C14A5-68, C14A5-97

following symptoms: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.6 to QR40.12. NOTE: National launch for this FOTA update is expected to begin November 06, 2023.

? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.62 and QR39.57 to QR40.12. NOTE: National launch for this FOTA update is expected to begin August 16, 2023

? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.

FCW Warning Light ON, DTC C14A5-68, C14A5-97

Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.

Customers may comment on the following: The Electronic Vehicle Information Center (EVIC) screen goes blank and only displays a green bar at the top at 120 kph (75 mph)

Customers may experience the following:Full Connectivity feature is missing.

IPhone Is Connected

Customers may experience:Amplifier inoperative intermittently or distorted sound; no audio message.

IPhone Is Connected

Customers may experience the following:Full Connectivity feature is missing.

IPhone Is Connected

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

Customers may comment on the following: The Electronic Vehicle Information Center (EVIC) screen goes blank and only displays a green bar at the top at 120 kph (75 mph)

Customers may experience: Amplifier inoperative intermittently or distorted sound; no audio message.

DTC B162F-64 Or B1638-64

published document)

Customers may comment on the following: The Electronic Vehicle Information Center (EVIC) screen goes blank and only displays a green bar at the top at 120 kph (75 mph)

published document)

Customers may experience the following:Full Connectivity feature is missing.

IPhone Is Connected

DTC B162F-64 Or B1638-64

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

Rear View Camera Inoperable Customers may experience the following: Rearview camera is inoperable, or shows a blue screen. This bulletin involves replacing the rearview camera main harness.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

"

experience any symptoms.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

notification on customers mobile application."

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs) have been set: ? **B1A7D-2F- Start Button-Signal Erratic** ? B1053-64 RFHM (KIN Communication) - Signal Plausibility Failure Customers may also experience: ? **Vehicle can not be switched off using the keyless button.** ? ?Service Passive Entry? light on cluster. ? Vehicle will not shut off with DTC B1053-64. ? Vehicle may not start with DTC B1053-64. This bulletin involves updating the RFHM module with the latest available software.

? Outdated vehicle data on customer's mobile app. ? Connected Services maintenance popup displayed on the radio screen. ? Connected Services battery maintenance popup displayed on the radio screen. This bulletin involves reprogramming the Global Telematics Box Module with the latest available software.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? /B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs) have been set: ? **B1A7D-2F- Start Button-Signal Erratic** ? B1053-64 RFHM (KIN Communication) - Signal Plausibility Failure Customers may also experience: ? **Vehicle can not be switched off using the keyless button.** ? ?Service Passive Entry? light on cluster. ? Vehicle will not shut off with DTC B1053-64. ? Vehicle may not start with DTC B1053-64. This bulletin involves updating the RFHM module with the latest available software.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

This bulletin involves inspecting the software level and updating the software to: B1 - 47.00.15 M1 - 45.06.06 H1 - 47.00.16

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. Estimated National launch date for 1st FOTA update is expected on 07/22/2022. 2nd FOTA 1-2 weeks after 1st FOTA completes: 1st step from 3.8i to 3.8j2+ and 2nd step 3.8j2+ to 4.30. No dealership visit required, send 2 step TBM updates over the air. Customers may experience one or more of the following: Message displayed on the radio screen, "Uconnect Box requires service. Please visit an authorized dealer."Fig.1. Error Message Remote operation is not working. If the vehicle?s ignition is off state more than 7 days and less than 21 days, Remote ops do not work. Vehicle info is not working (or vehicle info is not giving correct information). Vehicle finder is not working.

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. Estimated National launch date for 1st FOTA update is expected on 07/22/2022. 2nd FOTA 1-2 weeks after 1st FOTA completes: 1st step from 3.8i to 3.8j2+ and 2nd step 3.8j2+ to 4.30. No dealership visit required, send 2 step TBM updates over the air. Customers may experience one or more of the following: Message displayed on the radio screen, "Uconnect Box requires service. Please visit an authorized dealer."Fig.1. Error Message Remote operation is not working. If the vehicle?s ignition is off state more than 7 days and less than 21 days, Remote ops do not work. Vehicle info is not working (or vehicle info is not giving correct information). Vehicle finder is not working.

Upon further investigation, one or more of the following fault codes may be set in the PCM:

The positive battery cable protective cover is missing.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure. In addition, the customer may notice the following condition(s):Service Passive Entry Light" on cluster and MIL code B1053-64. Vehicle will not shut off with DTC B1053-64. Vehicle may not start with DTC B1053-64.

Customers may notice the following: B22A9-17 - ECU Internal Performance-Circuit Voltage Above Threshold. P0D2A-00 - Battery Charger 1 Input Current Too High. P0CF3-00 - Control Pilot Circuit Open. P0CF4-00 - Control Pilot Circuit Performance. B22A9-87 - ECU Internal Performance-Missing Message.

Customers may notice the following:Message on the cluster - Headlamp (low beam) is out but the headlamps are all functioning properly.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set:P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation).

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set:P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation).

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DiagnosticTrouble Code (DTC) has been set: P0031 - O2 Sensor 1/1 Heater Circuit Low.

Upon further investigation, one or more of the following fault codes may be set in the PCM:

must be followed for BEV/Hybrid vehicles that are on display at dealership showrooms.

The positive battery cable protective cover is missing.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure. In addition, the customer may notice the following condition(s):Service Passive Entry Light" on cluster and MIL code B1053-64. Vehicle will not shut off with DTC B1053-64. Vehicle may not start with DTC B1053-64.

Customers may notice the following: B22A9-17 - ECU Internal Performance-Circuit Voltage Above Threshold. P0D2A-00 - Battery Charger 1 Input Current Too High. P0CF3-00 - Control Pilot Circuit Open. P0CF4-00 - Control Pilot Circuit Performance. B22A9-87 - ECU Internal Performance-Missing Message.

Customers may notice the following:Message on the cluster - Headlamp (low beam) is out but the headlamps are all functioning properly.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set:P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation).

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set:P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation).

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

Drivers Monitoring Module Manifold Absolute Pressure (MAP) Sensor Not Installed Properly Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P006D-00 - Barometric Pressure - Inlet Air Pressure Correlation. P012C-00 - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low. P012D-00 - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High. P1189-00 - Inlet Air Pressure Sensor Circuit Low. P1190-00 - Inlet Air Pressure Sensor Circuit High. This bulletin involves measuring the distance between the lower base of the MAP sensor and the surface of the intake air line and, if required, replacing the MAP sensor.

Upon further investigation the technician must find one or more of the following Diagnostic Trouble Codes (DTC)s have been set: P012C - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit Low. P012D - Turbocharger/Supercharger Inlet Air Pressure Sensor 1 Circuit High. P006C-MAP - Turbocharger Inlet Air Pressure Correlation. "

following: Oil leaks from the engine compartment, engine/transmission coupling. This bulletin supersedes Technical Service Bulletin (TSB) 09-021-24, date of issue November 23, 2024, which should be removed from your files. All revisions are highlighted with **asterisks** and include new Labor Times."

following: Oil leaks from the engine compartment, engine/transmission coupling. When the claimed fault is confirmed, replace the engine valley cap, according to the Repair Procedure"

Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section ""System Operation - Smart Charging System"". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC."

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? U0100-00 - Lost Communication with Engine Control Module (ECM). ? U1701-87 - Engine Control Module (ECM) - Missing message. Customer may also experience: ? Vehicle no start condition. This bulletin involves replacement of the PCM for a possible no start condition.

installed in the vehicle.

Customers may experience the following: After a short trip and shutting the engine off for 5 - 10 minutes, vehicle exhibits a long crank/start condition.

from 1st to 2nd - Upshifting from 2nd to 3rd Scan the vehicle for DTC?s. If none are related to transmission performance, test drive the vehicle and attempt to duplicate the customers concern. If the rough shifting occurs during one or more of the events listed above, then this is a known issue. Engineering is aware and developing a resolution to address these concerns. A Quick Learn can be performed to improve these concerns. But the concerns may reappear again and another Quick Learn may need to be performed. Valve body and/or transmission replacement WILL NOT correct these concerns. If DTC?s for the transmissions performance are found. Follow the DTC flow charts to root cause the customer concern.

Customers may experience one or more of the following: Possible engine stall when shifted into neutral at a stop (APAC and EMEA Only). Harsh 1-2 or 3-4 upshifts.

Customers may experience one or more of the following: Possible engine stall when shifted into neutral at a stop (APAC and EMEA Only). Harsh 1-2 or 3-4 upshifts.

Customers may experience one or more of the following: Possible engine stall when shifted into neutral at a stop (APAC and EMEA Only). Harsh 1-2 or 3-4 upshifts.

Customers may experience the following: After a short trip and shutting the engine off for 5 - 10 minutes, vehicle exhibits a long crank/start condition.

from 1st to 2nd - Upshifting from 2nd to 3rd Scan the vehicle for DTC?s. If none are related to transmission performance, test drive the vehicle and attempt to duplicate the customers concern. If the rough shifting occurs during one or more of the events listed above, then this is a known issue. Engineering is aware and developing a resolution to address these concerns. A Quick Learn can be performed to improve these concerns. But the concerns may reappear again and another Quick Learn may need to be performed. Valve body and/or transmission replacement WILL NOT correct these concerns. If DTC?s for the transmissions performance are found. Follow the DTC flow charts to root cause the customer concern.

Customers may experience the following: After a short trip and shutting the engine off for 5 - 10 minutes, vehicle exhibits a long crank/start condition.

from 1st to 2nd - Upshifting from 2nd to 3rd Scan the vehicle for DTC?s. If none are related to transmission performance, test drive the vehicle and attempt to duplicate the customers concern. If the rough shifting occurs during one or more of the events listed above, then this is a known issue. Engineering is aware and developing a resolution to address these concerns. A Quick Learn can be performed to improve these concerns. But the concerns may reappear again and another Quick Learn may need to be performed. Valve body and/or transmission replacement WILL NOT correct these concerns. If DTC?s for the transmissions performance are found. Follow the DTC flow charts to root cause the customer concern.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DiagnosticTrouble Codes (DTCs) have been set: P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM(North America Only). P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation)(North America Only). Customers may experience the following: Vehicle stalls out when coming to a stop, when engine is at or near idle(EMEA Only).

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Installing engine covers on these vehicles built after 3-12-2021 is not a warrantable concern.

Customers may experience one or more of the following concerns: Possible engine stall when shifted into neutral at a stop(APAC and EMEA only). Harsh 1-2 or 3-4 upshifts.

Customers may experience the following: After a short trip and shutting the engine off for 5 - 10 minutes, vehicle exhibits a long crank/start condition.

from 1st to 2nd - Upshifting from 2nd to 3rd Scan the vehicle for DTC?s. If none are related to transmission performance, test drive the vehicle and attempt to duplicate the customers concern. If the rough shifting occurs during one or more of the events listed above, then this is a known issue. Engineering is aware and developing a resolution to address these concerns. A Quick Learn can be performed to improve these concerns. But the concerns may reappear again and another Quick Learn may need to be performed. Valve body and/or transmission replacement WILL NOT correct these concerns. If DTC?s for the transmissions performance are found. Follow the DTC flow charts to root cause the customer concern.

Installing engine covers on these vehicles built after 3-12-2021 is not a warrantable concern.

Glove Box Door Difficult To Close Customers may experience the following: The glove compartment door is difficult to close. This bulletin involves installing a washer spacer stack to correct glove compartment door alignment.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

This bulletin involves replacing the power folding mirror/window switch assembly."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

1. This bulletin involves replacing the window seal and glass.

This bulletin includes inspecting the sunroof wind deflector for noise when closing and replacing the wind deflector if required.

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

Order the "R" part number for all orders:

this is normal and not a defect.

semi and full synthetic oils.

The Analog Speedometer Continues To Function

The Analog Speedometer Continues To Function

system

The customer may describe the following: The air conditioning is inoperable.

The customer may describe the following: The air conditioning is inoperable.

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance.

? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.

position and neutral sensors.

Customers may experience one or more of the following concerns:Harsh 1-2 or 3-4 upshifts

Customers may experience the following shift quality issue:1?2 upshift lag/delay when accelerating from a stop.

position and neutral sensors.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order a "68" part number for New unsold units only.

The purpose of this informative Technical Service Bulletin (TSB) is to support the Network on the following topics: Discern the different kinds of connected service issues (onboard / offboard). Support the customer in his journey to open a request via Customer Care. Address on the correct actions to properly manage a customer complaining about the received assistance."

Library for specifications so a suitable alternative can be used

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

assemblies are fogged with a light layer of condensation on the inside of the lenses. "

assemblies are fogged with a light layer of condensation on the inside of the lenses."

assemblies are fogged with a light layer of condensation on the inside of the lenses.

assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.

assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

The customer may describe the following: Clunk in front suspension when driving.

Sporadically Electronic Parking Brake (EPB) setting is lost. Sporadically Rearview Camera (RVC) image is kept active in forward driving. (Valid for all markets except North America). Sporadically Wireless disconnects and reconnects while TomTom connected services are working (traffic info, weather) and a native navigation route is set while Wireless is streaming music. **This bulletin involves updating the software via USB to 23.04.17.01.** "

B)