2020 Jeep Renegade TSBs

? Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 34.4 to 34.42.

FCW Warning Light ON, DTC C14A5-68, C14A5-97

? WiFi hotspot gives ?No Internet? connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.41F to JR34.42F. NOTE: The National campaign for this FOTA update launched July 5, 2023.

? Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 34.4 to 34.42.

FCW Warning Light ON, DTC C14A5-68, C14A5-97

Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.

Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.

Customers may comment on the following: The Electronic Vehicle Information Center (EVIC) screen goes blank and only displays a green bar at the top at 120 kph (75 mph)

Customers may experience the following:Full Connectivity feature is missing.

IPhone Is Connected

Customers may experience:Amplifier inoperative intermittently or distorted sound; no audio message.

IPhone Is Connected

Customers may experience the following:Full Connectivity feature is missing.

IPhone Is Connected

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

DTC B162F-64 Or B1638-64

Customers may comment on the following: The Electronic Vehicle Information Center (EVIC) screen goes blank and only displays a green bar at the top at 120 kph (75 mph)

Customers may experience: Amplifier inoperative intermittently or distorted sound; no audio message.

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

may experience the following:Radio changes distance, temperature and time format, after a network deep sleep.

DTC B162F-64 Or B1638-64

published document)

only displays a green bar at the top instead of a digital speed at 75MPH (120KPH), a new IPC software is available via TSB 08-126-21 Rev. A (RRT 21-116). Replacement of components is not necessary to correct this concern.

Customers may comment on the following: The Electronic Vehicle Information Center (EVIC) screen goes blank and only displays a green bar at the top at 120 kph (75 mph)

published document)

only displays a green bar at the top instead of a digital speed at 75MPH (120KPH), a new IPC software is available via TSB 08-126-21 Rev. A (RRT 21-116). Replacement of components is not necessary to correct this concern.

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

Customers may experience the following:Full Connectivity feature is missing.

IPhone Is Connected

may experience the following:Radio changes distance, temperature and time format, after a network deep sleep.

DTC B162F-64 Or B1638-64

DTC B162F-64 Or B1638-64

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

"

experience any symptoms.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

notification on customers mobile application."

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs) have been set: ? **B1A7D-2F- Start Button-Signal Erratic** ? B1053-64 RFHM (KIN Communication) - Signal Plausibility Failure Customers may also experience: ? **Vehicle can not be switched off using the keyless button.** ? ?Service Passive Entry? light on cluster. ? Vehicle will not shut off with DTC B1053-64. ? Vehicle may not start with DTC B1053-64. This bulletin involves updating the RFHM module with the latest available software.

? Outdated vehicle data on customer's mobile app. ? Connected Services maintenance popup displayed on the radio screen. ? Connected Services battery maintenance popup displayed on the radio screen. This bulletin involves reprogramming the Global Telematics Box Module with the latest available software.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? /B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs) have been set: ? **B1A7D-2F- Start Button-Signal Erratic** ? B1053-64 RFHM (KIN Communication) - Signal Plausibility Failure Customers may also experience: ? **Vehicle can not be switched off using the keyless button.** ? ?Service Passive Entry? light on cluster. ? Vehicle will not shut off with DTC B1053-64. ? Vehicle may not start with DTC B1053-64. This bulletin involves updating the RFHM module with the latest available software.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. Estimated National launch date for 1st FOTA update is expected on 07/22/2022. 2nd FOTA 1-2 weeks after 1st FOTA completes: 1st step from 3.8i to 3.8j2+ and 2nd step 3.8j2+ to 4.30. No dealership visit required, send 2 step TBM updates over the air. Customers may experience one or more of the following: Message displayed on the radio screen, "Uconnect Box requires service. Please visit an authorized dealer."Fig.1. Error Message Remote operation is not working. If the vehicle?s ignition is off state more than 7 days and less than 21 days, Remote ops do not work. Vehicle info is not working (or vehicle info is not giving correct information). Vehicle finder is not working.

Diagnostic Trouble Code (DTC) U02A3 ? Lost Communication ith Particulate Matter (PM) Sensor, Set After PM Sensor Replacement.

level to 39.2 Customers may experience one or more of the following:Language set in Spanish, and try to search for an address with Voice Recognition (VR), it will not recognize these locations.VR can not find street names / location in Catalan language (present in Barcelona area and nearby). To correct this symptom, the radio SW has to be at QR39.2 and the Nav Map SW version has to be at 19Q2. In the Uconnect App, under Live>Jeep Skills>Customer will see ?Current? meter which is displaying incorrect amperage readings.The battery current indicator indicates an incorrect value, it is showing the number 65536 stating that it is exactly in the full range scale. Audio inoperative. No audio from any media source. No audio from navigation prompts. No audio from cell or initial message prompt The audio/sound will continue to work properly for the chimes and touchscreen beeps. The soft key for the heated seats and heated steering wheel are grayed out on the display screen and these features do not work.

(PCM) with the latest available software.

(DTCs) This bulletin involves replacing all four wheel speed sensors due to oxidation or water intrusion into the sensor. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).B1 vehicles may have the following DTCs:C0031-01 - Left front speed sensor - General electrical failure. C0031-29 - Left front speed sensor - Invalid signal. C0034-01 - Right front speed sensor - General electrical failure. C0034-29 - Right front speed sensor - Invalid signal. C0037-01 - Left rear speed sensor - General electrical failure. C0037-29 - Left rear speed sensor - Invalid signal. C003A-01 - Right rear speed sensor - General electrical failure. C003A-29 - Right rear speed sensor - Invalid signal. M1 vehicles may have the following DTCs:C0031-1D - Left Front Wheel Speed Sensor-Circuit Current Out of Range. C0034-1D - Right Front Wheel Speed Sensor-Circuit Current Out of Range. C0037-1D - Left Rear Wheel Speed Sensor-Circuit Current Out of Range. C003A-1D - Right Rear Wheel Speed Sensor-Circuit Current Out of Range. C0031-62 - Left Front Wheel Speed Sensor-Signal Compare Failure. C0034-62 - Right Front Wheel Speed Sensor-Signal Compare Failure. C0037-62 - Left Rear Wheel Speed Sensor-Signal Compare Failure. C003A-62 - Right Rear Wheel Speed Sensor-Signal Compare Failure. C0031-2F - Left Front Wheel Speed Sensor-Signal Erratic. C0034-2F - Right Front Wheel Speed Sensor-Signal Erratic. C0037-2F - Left Rear Wheel Speed Sensor-Signal Erratic. C003A-2F - Right Rear Wheel Speed Sensor-Signal Erratic.

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. Estimated National launch date for 1st FOTA update is expected on 07/22/2022. 2nd FOTA 1-2 weeks after 1st FOTA completes: 1st step from 3.8i to 3.8j2+ and 2nd step 3.8j2+ to 4.30. No dealership visit required, send 2 step TBM updates over the air. Customers may experience one or more of the following: Message displayed on the radio screen, "Uconnect Box requires service. Please visit an authorized dealer."Fig.1. Error Message Remote operation is not working. If the vehicle?s ignition is off state more than 7 days and less than 21 days, Remote ops do not work. Vehicle info is not working (or vehicle info is not giving correct information). Vehicle finder is not working.

particulate sensor when one or more of the following Diagnostic Trouble Codes (DTCs) are active in the Powertrain Control Module (PCM). Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs. P24D1-00 - Particulate Matter Sensor Regeneration Incomplete. P24AE-00 - Particulate Matter Sensor Circuit.

message, and the headlights are functional, please refer to SOL Publication S2008000125. Per the SOL, software is being developed to address the issue and component replacement will not resolve this issue.

Upon further investigation, one or more of the following fault codes may be set in the PCM:

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

If the software update is performed on a radio with software below 19.9, the radio could be damaged and will need to be replaced. Customers may experience one or more of the following:Lost radio presets. Radio display screen is black when the ignition is on. Radio may reset, turn itself off and then back on again. Park assist chime will continue to chime after the vehicle is turn off. Radio will display the incorrect speed limit in kph when approaching a road speed camera. In addition the following enhancements are included:Voice Recognition (VR) and Bluetooth improvements. Improvements for Off-road pages.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure. In addition, the customer may notice the following condition(s):Service Passive Entry Light" on cluster and MIL code B1053-64. Vehicle will not shut off with DTC B1053-64. Vehicle may not start with DTC B1053-64.

Customers may notice the following: B22A9-17 - ECU Internal Performance-Circuit Voltage Above Threshold. P0D2A-00 - Battery Charger 1 Input Current Too High. P0CF3-00 - Control Pilot Circuit Open. P0CF4-00 - Control Pilot Circuit Performance. B22A9-87 - ECU Internal Performance-Missing Message.

Customers may notice the following:Message on the cluster - Headlamp (low beam) is out but the headlamps are all functioning properly.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). P0607 - Control Module Performance.

(DTCs) This bulletin involves replacing all four wheel speed sensors due to oxidation or water intrusion into the sensor. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).M1&M6 vehicles may have one or more of the following DTCs:C0031-1D - Left Front Wheel Speed Sensor-Circuit Current Out of Range. C0034-1D - Right Front Wheel Speed Sensor-Circuit Current Out of Range. C0037-1D - Left Rear Wheel Speed Sensor-Circuit Current Out of Range. C003A-1D - Right Rear Wheel Speed Sensor-Circuit Current Out of Range. C0031-62 - Left Front Wheel Speed Sensor-Signal Compare Failure. C0034-62 - Right Front Wheel Speed Sensor-Signal Compare Failure. C0037-62 - Left Rear Wheel Speed Sensor-Signal Compare Failure. C003A-62 - Right Rear Wheel Speed Sensor-Signal Compare Failure. C0031-2F - Left Front Wheel Speed Sensor-Signal Erratic. C0034-2F - Right Front Wheel Speed Sensor-Signal Erratic. C0037-2F - Left Rear Wheel Speed Sensor-Signal Erratic. C003A-2F - Right Rear Wheel Speed Sensor-Signal Erratic. B1 vehicles may have one or more of the following DTCs:C0031-01 - Left front speed sensor - General electrical failure. C0031-29 - Left front speed sensor - Invalid signal. C0034-01 - Right front speed sensor - General electrical failure. C0034-29 - Right front speed sensor - Invalid signal. C0037-01 - Left rear speed sensor - General electrical failure. C0037-29 - Left rear speed sensor - Invalid signal. C003A-01 - Right rear speed sensor - General electrical failure. C003A-29 - Right rear speed sensor - Invalid signal.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). P0607 - Control Module Performance.

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

Upon further investigation, one or more of the following fault codes may be set in the PCM:

must be followed for BEV/Hybrid vehicles that are on display at dealership showrooms.

If the software update is performed on a radio with software below 19.9, the radio could be damaged and will need to be replaced. Customers may experience one or more of the following:Lost radio presets. Radio display screen is black when the ignition is on. Radio may reset, turn itself off and then back on again. Park assist chime will continue to chime after the vehicle is turn off. Radio will display the incorrect speed limit in kph when approaching a road speed camera. In addition the following enhancements are included:Voice Recognition (VR) and Bluetooth improvements. Improvements for Off-road pages.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure. In addition, the customer may notice the following condition(s):Service Passive Entry Light" on cluster and MIL code B1053-64. Vehicle will not shut off with DTC B1053-64. Vehicle may not start with DTC B1053-64.

Customers may notice the following: B22A9-17 - ECU Internal Performance-Circuit Voltage Above Threshold. P0D2A-00 - Battery Charger 1 Input Current Too High. P0CF3-00 - Control Pilot Circuit Open. P0CF4-00 - Control Pilot Circuit Performance. B22A9-87 - ECU Internal Performance-Missing Message.

Customers may notice the following:Message on the cluster - Headlamp (low beam) is out but the headlamps are all functioning properly.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). P0607 - Control Module Performance.

(DTCs) This bulletin involves replacing all four wheel speed sensors due to oxidation or water intrusion into the sensor. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).M1&M6 vehicles may have one or more of the following DTCs:C0031-1D - Left Front Wheel Speed Sensor-Circuit Current Out of Range. C0034-1D - Right Front Wheel Speed Sensor-Circuit Current Out of Range. C0037-1D - Left Rear Wheel Speed Sensor-Circuit Current Out of Range. C003A-1D - Right Rear Wheel Speed Sensor-Circuit Current Out of Range. C0031-62 - Left Front Wheel Speed Sensor-Signal Compare Failure. C0034-62 - Right Front Wheel Speed Sensor-Signal Compare Failure. C0037-62 - Left Rear Wheel Speed Sensor-Signal Compare Failure. C003A-62 - Right Rear Wheel Speed Sensor-Signal Compare Failure. C0031-2F - Left Front Wheel Speed Sensor-Signal Erratic. C0034-2F - Right Front Wheel Speed Sensor-Signal Erratic. C0037-2F - Left Rear Wheel Speed Sensor-Signal Erratic. C003A-2F - Right Rear Wheel Speed Sensor-Signal Erratic. B1 vehicles may have one or more of the following DTCs:C0031-01 - Left front speed sensor - General electrical failure. C0031-29 - Left front speed sensor - Invalid signal. C0034-01 - Right front speed sensor - General electrical failure. C0034-29 - Right front speed sensor - Invalid signal. C0037-01 - Left rear speed sensor - General electrical failure. C0037-29 - Left rear speed sensor - Invalid signal. C003A-01 - Right rear speed sensor - General electrical failure. C003A-29 - Right rear speed sensor - Invalid signal.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P2110 - Electronic Throttle Control System Bank 1 - Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). P0607 - Control Module Performance.

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

flash drive(s) to update the radio software level to 39.2.It is critical that every step of the bulletin is reviewed and performed properly. If any steps are missed the radio can be damaged and may need to be replaced. Customers may experience one or more of the following:If the language is set in Spanish, and the customer tries to search for an address with Voice Recognition (VR), it will not recognize these locations.VR can not find street names / location in Catalan language (present in Barcelona area and nearby). To correct this symptom, the radio SW has to be at QR39.2 and the Nav Map SW version has to be at 19Q2. In the Uconnect App, under Live>Jeep Skills>Indicator, the ?Current? meter will display the incorrect amperage readings.The battery current indicator will display the incorrect value, it will show the number 65536, stating that it is exactly in the full range scale. Audio inoperative. No audio from any media source. No audio from navigation prompts. No audio from cell or initial message prompt.The audio/sound will continue to work properly for the chimes and touchscreen beeps. Lost preset issue. The soft key for the heated seats and heated steering wheel are grayed out on the display screen and these features do not work. If the vehicle has been turned off for a long time, the settings for auto folding side mirrors is turned off (2018). Radio resets intermittently (2018). Radio display screen locks up (2018). Park assist chime will continue to chime, after the vehicle is turned off (2018). Radio will display the incorrect speed limit in kph, when approaching a road speed camera (2018). Uconnect Live feature may not function properly (2018).

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

level to 39.2 Customers may experience one or more of the following:Language set in Spanish, and try to search for an address with Voice Recognition (VR), it will not recognize these locations.VR can not find street names / location in Catalan language (present in Barcelona area and nearby). To correct this symptom, the radio SW has to be at QR39.2 and the Nav Map SW version has to be at 19Q2. In the Uconnect App, under Live>Jeep Skills>Customer will see ?Current? meter which is displaying incorrect amperage readings.The battery current indicator indicates an incorrect value, it is showing the number 65536 stating that it is exactly in the full range scale. Audio inoperative. No audio from any media source. No audio from navigation prompts. No audio from cell or initial message prompt The audio/sound will continue to work properly for the chimes and touchscreen beeps. The soft key for the heated seats and heated steering wheel are grayed out on the display screen and these features do not work.

level to 39.2 Customers may experience one or more of the following:Language set in Spanish, and try to search for an address with Voice Recognition (VR), it will not recognize these locations.VR can not find street names / location in Catalan language (present in Barcelona area and nearby). To correct this symptom, the radio SW has to be at QR39.2 and the Nav Map SW version has to be at 19Q2. In the Uconnect App, under Live>Jeep Skills>Customer will see ?Current? meter which is displaying incorrect amperage readings.The battery current indicator indicates an incorrect value, it is showing the number 65536 stating that it is exactly in the full range scale. Audio inoperative. No audio from any media source. No audio from navigation prompts. No audio from cell or initial message prompt The audio/sound will continue to work properly for the chimes and touchscreen beeps. The soft key for the heated seats and heated steering wheel are grayed out on the display screen and these features do not work.

(PCM) with the latest available software.

(DTCs) This bulletin involves replacing all four wheel speed sensors due to oxidation or water intrusion into the sensor. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).B1 vehicles may have the following DTCs:C0031-01 - Left front speed sensor - General electrical failure. C0031-29 - Left front speed sensor - Invalid signal. C0034-01 - Right front speed sensor - General electrical failure. C0034-29 - Right front speed sensor - Invalid signal. C0037-01 - Left rear speed sensor - General electrical failure. C0037-29 - Left rear speed sensor - Invalid signal. C003A-01 - Right rear speed sensor - General electrical failure. C003A-29 - Right rear speed sensor - Invalid signal. M1 vehicles may have the following DTCs:C0031-1D - Left Front Wheel Speed Sensor-Circuit Current Out of Range. C0034-1D - Right Front Wheel Speed Sensor-Circuit Current Out of Range. C0037-1D - Left Rear Wheel Speed Sensor-Circuit Current Out of Range. C003A-1D - Right Rear Wheel Speed Sensor-Circuit Current Out of Range. C0031-62 - Left Front Wheel Speed Sensor-Signal Compare Failure. C0034-62 - Right Front Wheel Speed Sensor-Signal Compare Failure. C0037-62 - Left Rear Wheel Speed Sensor-Signal Compare Failure. C003A-62 - Right Rear Wheel Speed Sensor-Signal Compare Failure. C0031-2F - Left Front Wheel Speed Sensor-Signal Erratic. C0034-2F - Right Front Wheel Speed Sensor-Signal Erratic. C0037-2F - Left Rear Wheel Speed Sensor-Signal Erratic. C003A-2F - Right Rear Wheel Speed Sensor-Signal Erratic.

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

The first step will take the ECU SW from 201772 to 201774 and the second step will take the software from 201774 to 201775. The customer may notice:Pop-up message displayed on the radio screen ?Connected Service Not Working?. SOS and Assist Buttons are disabled.

The first step will take the ECU SW from 201772 to 201774 and the second step will take the software from 201774 to 201775. The customer may notice:Pop-up message displayed on the radio screen ?Connected Service Not Working?. SOS and Assist Buttons are disabled.

particulate sensor when one or more of the following Diagnostic Trouble Codes (DTCs) are active in the Powertrain Control Module (PCM). Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs. P24D1-00 - Particulate Matter Sensor Regeneration Incomplete. P24AE-00 - Particulate Matter Sensor Circuit.

message, and the headlights are functional, please refer to SOL Publication S2008000125. Per the SOL, software is being developed to address the issue and component replacement will not resolve this issue.

The customer may experience a Malfunction Indicator Lamp (MIL) illumination or describe the following symptoms:B1007-15 - Front-Lateral Left Turn Light-Circuit Short To Battery Or Open(2020 MY only). B1008-15 - Front-Lateral Right Turn Light-Circuit Short To Battery Or Open(2020 MY only). B1107-15 - Rear Left Turn Light-Circuit Short To Battery Or Open(2020 MY only). B1108-15 - Rear Right Turn Light-Circuit Short To Battery Or Open(2020 MY only). When the doors' lock is activated by the key, the anti-theft system signals with three beeps and blinks the turn lamps nine times, without any open door or open window(2020 MY only). The customer may also experience an intermittent message ?Service Power Steering? appearing on Electronic Vehicle Information Center (EVIC), without loosing the power steering assistance, followed by the DTC:C1214-87 - Conf Data Code Request Message - Missing Message. The customer may also experience an intermittent MIL ?Exterior Bulb Failure Indicator? illumination and any exterior lights or bulbs are malfunctioning, followed by the DTC's:B100A-15 - Combined Rear Right Stop And Park Ch 1 - Circuit Short To Battery Or Open. B100B-15 - Combined Rear Left Stop And Park Ch 2 - Circuit Short To Battery Or Open. B100C-15 - Combined Rear Right Stop And Park Ch 2 - Circuit Short To Battery Or Open.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

and function of the Uconnect Box/Telematic Box Module 2.0.

Stop Start Equipped Vehicles

and function of the Uconnect Box/Telematic Box Module 2.0.

and function of the Uconnect Box/Telematic Box Module 2.0.

The customer may experience a Malfunction Indicator Lamp (MIL) illumination or describe the following symptom:Intermittent message ?Service Power Steering? appearing on ElectronicVehicle Information Center (EVIC), without loosing the power steering assistance, followed by the DTC: C1214-87 - Conf Data Code Request Message - Missing Message. The customer may also experience an intermittent MIL ?Exterior Bulb Failure Indicator? illumination and anyexterior lights or bulbs are malfunctioning, followed by the DTC's: B100A-15 - Combined Rear Right Stop And Park Ch 1 - Circuit Short To Battery Or Open. B100B-15 - Combined Rear Left Stop And Park Ch 2 - Circuit Short To BatteryOr Open. B100C-15 - Combined Rear Right Stop And Park Ch 2 - Circuit Short To Battery Or Open.

following: Oil leaks from the engine compartment, engine/transmission coupling. This bulletin supersedes Technical Service Bulletin (TSB) 09-021-24, date of issue November 23, 2024, which should be removed from your files. All revisions are highlighted with **asterisks** and include new Labor Times."

following: Oil leaks from the engine compartment, engine/transmission coupling. When the claimed fault is confirmed, replace the engine valley cap, according to the Repair Procedure"

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? P1061 - Cylinder 1 Oil Supply Solenoid Valve Stuck. ? P1065 - Cylinder 1 Oil Supply Solenoid Valve Switch On Time Out Of Range. ? P1062 - Cylinder 2 Oil Supply Solenoid Valve Stuck. ? P1067 - Cylinder 2 Oil Supply Solenoid Valve Switch On Time Out Of Range. ? P1063 - Cylinder 3 Oil Supply Solenoid Valve Stuck. ? P1069 - Cylinder 3 Oil Supply Solenoid Valve Switch On Time Out Of Range. ? P1471 - Catalyst Protection (Bank 1). ? P0301 -Cylinder 1 Misfire. ? P0302 - Cylinder 2 Misfire. ? P0303 - Cylinder 3 Misfire. ? P0304 - Cylinder 4 Misfire. ? P1064 - Cylinder 4 Oil Supply Solenoid Valve Stuck. ? P106B - Cylinder 4 Oil Supply Solenoid Valve Switch On Time Out Of Range. ? P2110 - Electronic Throttle Control System Bank 1 Forced Limited RPM. ? P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). ? P0607 - Control Module Performance. **In addition, the customers may experience one or more of the following: ? Engine Stop/Start does not work as expected and it is often automatically deactivated (Enlarged Europe Only).** ? Poor engine performance. This bulletin involves reprogramming the PCM with the latest available software.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTC): P1061 - Cylinder 1 Oil Supply Solenoid Valve Stuck. P1065 - Cylinder 1 Oil Supply Solenoid Valve Switch On Time Out Of Range. P1062 - Cylinder 2 Oil Supply Solenoid Valve Stuck. P1067 - Cylinder 2 Oil Supply Solenoid Valve Switch On Time Out Of Range. P1063 - Cylinder 3 Oil Supply Solenoid Valve Stuck. P1069 - Cylinder 3 Oil Supply Solenoid Valve Switch On Time Out Of Range. P1471 - Catalyst Protection (Bank 1). P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. **Customers may experience one or more of the following: Stop/start function deactivated.** Poor engine performance. This bulletin involves reprogramming the PCM with the latest available software.

installed in the vehicle.

Customers may experience the following: After a short trip and shutting the engine off for 5 - 10 minutes, vehicle exhibits a long crank/start condition.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: P2002-00 - Diesel particulate Filter Flow Resistance Monitoring Too High Level 2 Component or System Operation Obstructed or Blocked. Customers equipped with a 6-SPD C635 Dual Dry Clutch Automatic Transmission (Sales code DA1) may also experience an injector knocking noise during acceleration (without MIL illumination).

positive starter solenoid cable at the starter motor. Customers may experience one of the following:Difficulty in starting the vehicle. No crank, when trying to start vehicle.

(ETL, ETM, ETN Engines)

Customers may experience the following: After a short trip and shutting the engine off for 5 - 10 minutes, vehicle exhibits a long crank/start condition.

Customers may experience the following: After a short trip and shutting the engine off for 5 - 10 minutes, vehicle exhibits a long crank/start condition.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set: P1061 - Cylinder 1 Oil Supply Solenoid Valve Stuck. P1065 - Cylinder 1 Oil Supply Solenoid Valve Switch On Time Out Of Range. P1062 - Cylinder 2 Oil Supply Solenoid Valve Stuck. P1067 - Cylinder 2 Oil Supply Solenoid Valve Switch On Time Out Of Range. P1063 - Cylinder 3 Oil Supply Solenoid Valve Stuck. P1069 - Cylinder 3 Oil Supply Solenoid Valve Switch On Time Out Of Range. P1471 - Catalyst Protection (Bank 1). P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P1064 - Cylinder 4 Oil Supply Solenoid Valve Stuck. P106B - Cylinder 4 Oil Supply Solenoid Valve Switch On Time Out Of Range. P2110 - Electronic Throttle Control System Bank 1 Forced Limited RPM. P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). P0607 - Control Module Performance. In addition, the customer may notice the following condition: Poor engine performance.

installed in the vehicle.

reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0A92 - Hybrid Generator Performance. P0BFA - Drive Motor "B" Phase W Current Sensor Circuit Range/Performance. P0BF6 - Drive Motor B Inverter Phase V Current Sensor Circuit Range/Performance. P0BF2 - Drive Motor B Inverter Phase U Current Sensor Circuit Range/Performance. P0BFE - Drive Motor B Phase U-V-W Current Sensor Correlation. P0BEE - Drive Motor A Inverter Phase W Current Sensor Circuit Performance. P0BEA - Drive Motor A Inverter Phase V Current Sensor Circuit Performance. P0BE6 - Drive Motor A Inverter Phase U Current Sensor Circuit Performance. P0BFD - Drive Motor A Phase U-V-W Current Sensor Correlation. In addition, the customer may notice one or more of the following conditions:Turtle (Limp Home Mode) light is on. Service 4WD light is on.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

the injector seals must be replaced. Please use Special Tool Kit # 2072700140 for replacing the seals. Please order a loaner kit through the MOPAR Essential Tools website at https://moparessentialtools.com or call 1-855-298-2687.

Customers may experience the following: After a short trip and shutting the engine off for 5 - 10 minutes, vehicle exhibits a long crank/start condition.

reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0A92 - Hybrid Generator Performance. P0BFA - Drive Motor "B" Phase W Current Sensor Circuit Range/Performance. P0BF6 - Drive Motor B Inverter Phase V Current Sensor Circuit Range/Performance. P0BF2 - Drive Motor B Inverter Phase U Current Sensor Circuit Range/Performance. P0BFE - Drive Motor B Phase U-V-W Current Sensor Correlation. P0BEE - Drive Motor A Inverter Phase W Current Sensor Circuit Performance. P0BEA - Drive Motor A Inverter Phase V Current Sensor Circuit Performance. P0BE6 - Drive Motor A Inverter Phase U Current Sensor Circuit Performance. P0BFD - Drive Motor A Phase U-V-W Current Sensor Correlation. In addition, the customer may notice one or more of the following conditions:Turtle (Limp Home Mode) light is on. Service 4WD light is on.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: P2002-00 - Diesel particulate Filter Flow Resistance Monitoring Too High Level 2 Component or System Operation Obstructed or Blocked. Customers equipped with a 6-SPD C635 Dual Dry Clutch Automatic Transmission (Sales code DA1) may also experience an injector knocking noise during acceleration (without MIL illumination).

positive starter solenoid cable at the starter motor. Customers may experience one of the following:Difficulty in starting the vehicle. No crank, when trying to start vehicle.

Upon further inspection, fault code P219A - Bank 1 Air-Fuel Ratio Imbalance may be found in the powertrain control module (PCM) as pending, active, or stored. Other fault codes P1066, P1068, P106A, or P106C (Solenoid Valve Switch Off Time Out of Range) may also be stored. Customer may also complain about loss of power or engine running rough while P219A is active.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:P0238-00 - Positive Boost Pressure Governor Deviation Low Pressure Signal Calculation Failure. Customer may also notice:Erratic engine idle. Premature alternator pulley failure. Other software enhancements include:Improvement to avoid soot formation in the intake system that can cause engine speed oscillation at idle. Improvement to the alternator strategy to prevent alternator pulley failure.

the injector seals must be replaced. Please use Special Tool Kit # 2072700140 for replacing the seals. Please order a loaner kit through the MOPAR Essential Tools website at https://moparessentialtools.com or call 1-855-298-2687.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

This bulletin involves replacing the power folding mirror/window switch assembly."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

1. This bulletin involves replacing the window seal and glass.

This bulletin includes inspecting the sunroof wind deflector for noise when closing and replacing the wind deflector if required.

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

This bulletin involves replacing the power folding mirror/window switch assembly on the door.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

panel pull cups due to paint delamination. The customer may describe paint peeling on the left, right, or both front door panel pull cups.

Some of the PHEV vehicle hood decals may be missing or has the incorrect decal been installed.

Some of the PHEV vehicle hood decals may be missing or has the incorrect decal been installed.

Some of the PHEV vehicle hood decals may be missing or has the incorrect decal been installed.

Some of the PHEV vehicle hood decals may be missing or has the incorrect decal been installed.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

panel pull cups due to paint delamination. The customer may describe paint peeling on the left, right, or both front door panel pull cups.

Order the "R" part number for all orders:

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

Detected Message

The customer may describe a crank, no start condition, in freezing temperatures. This condition can be caused by condensation freezing in the muffler assembly.

The customer may describe a crank, no start condition, in freezing temperatures. This condition can be caused by condensation freezing in the muffler assembly.

The customer may describe a crank, no start condition, in freezing temperatures. This condition can be caused by condensation freezing in the muffler assembly.

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance.

? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.

position and neutral sensors.

position and neutral sensors.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P1D5B - Supply Sensor C -VS3 - Circuit Voltage Out Of Range.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P1D5B - Supply Sensor C -VS3 - Circuit Voltage Out Of Range.

Customers may experience the following:Erratic or inconsistent shifting. Software enhancements include:Improved shift enhancements due to PCM improvements.

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

assemblies are fogged with a light layer of condensation on the inside of the lenses. "

assemblies are fogged with a light layer of condensation on the inside of the lenses."

assemblies are fogged with a light layer of condensation on the inside of the lenses.

assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.

assemblies are fogged with a light layer of condensation on the inside of the lenses (Fig. 1) . This bulletin is to communicate the procedure for head lamp condensation clearing.

EVIC Displays Service Passive Entry

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

EVIC Displays Service Passive Entry

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

The customer/dealer may notice:The vehicle is missing the spare wheel anti-theft screws for the spare wheel.

system

The customer may describe the following: The air conditioning is inoperable.

The customer may describe the following: The air conditioning is inoperable.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order a "68" part number for New unsold units only.

The purpose of this informative Technical Service Bulletin (TSB) is to support the Network on the following topics: Discern the different kinds of connected service issues (onboard / offboard). Support the customer in his journey to open a request via Customer Care. Address on the correct actions to properly manage a customer complaining about the received assistance."

Library for specifications so a suitable alternative can be used

level to 34.2 Customers may experience one or more of the following:Audio inoperative. No audio from any media source. No audio from navigation prompts. No audio from cell or initial message promptThe audio/sound will continue to work properly for the chimes and touchscreen beeps. The soft key for the heated seats and heated steering wheel are grayed out on the display screen and these features do not work.

level to 34.2 Customers may experience one or more of the following:Audio inoperative. No audio from any media source. No audio from navigation prompts. No audio from cell or initial message promptThe audio/sound will continue to work properly for the chimes and touchscreen beeps. The soft key for the heated seats and heated steering wheel are grayed out on the display screen and these features do not work.

level to 34.2 Customers may experience one or more of the following:Audio inoperative. No audio from any media source. No audio from navigation prompts. No audio from cell or initial message promptThe audio/sound will continue to work properly for the chimes and touchscreen beeps. The soft key for the heated seats and heated steering wheel are grayed out on the display screen and these features do not work.

Sporadically Electronic Parking Brake (EPB) setting is lost. Sporadically Rearview Camera (RVC) image is kept active in forward driving. (Valid for all markets except North America). Sporadically Wireless disconnects and reconnects while TomTom connected services are working (traffic info, weather) and a native navigation route is set while Wireless is streaming music. **This bulletin involves updating the software via USB to 23.04.17.01.** "

B)