2018 Jeep Renegade TSBs

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set: ? /B0050-1D - Driver Front Buckle Switch - Out of Range (Active or Stored). ? B0050-13 - Driver Front Buckle Switch - Circuit open (Active or Stored). This bulletin involves replacing the inline seat connector.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

(DTCs) This bulletin involves replacing all four wheel speed sensors due to oxidation or water intrusion into the sensor. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).B1 vehicles may have the following DTCs:C0031-01 - Left front speed sensor - General electrical failure. C0031-29 - Left front speed sensor - Invalid signal. C0034-01 - Right front speed sensor - General electrical failure. C0034-29 - Right front speed sensor - Invalid signal. C0037-01 - Left rear speed sensor - General electrical failure. C0037-29 - Left rear speed sensor - Invalid signal. C003A-01 - Right rear speed sensor - General electrical failure. C003A-29 - Right rear speed sensor - Invalid signal. M1 vehicles may have the following DTCs:C0031-1D - Left Front Wheel Speed Sensor-Circuit Current Out of Range. C0034-1D - Right Front Wheel Speed Sensor-Circuit Current Out of Range. C0037-1D - Left Rear Wheel Speed Sensor-Circuit Current Out of Range. C003A-1D - Right Rear Wheel Speed Sensor-Circuit Current Out of Range. C0031-62 - Left Front Wheel Speed Sensor-Signal Compare Failure. C0034-62 - Right Front Wheel Speed Sensor-Signal Compare Failure. C0037-62 - Left Rear Wheel Speed Sensor-Signal Compare Failure. C003A-62 - Right Rear Wheel Speed Sensor-Signal Compare Failure. C0031-2F - Left Front Wheel Speed Sensor-Signal Erratic. C0034-2F - Right Front Wheel Speed Sensor-Signal Erratic. C0037-2F - Left Rear Wheel Speed Sensor-Signal Erratic. C003A-2F - Right Rear Wheel Speed Sensor-Signal Erratic.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

If the software update is performed on a radio with software below 19.9, the radio could be damaged and will need to be replaced. Customers may experience one or more of the following:Lost radio presets. Radio display screen is black when the ignition is on. Radio may reset, turn itself off and then back on again. Park assist chime will continue to chime after the vehicle is turn off. Radio will display the incorrect speed limit in kph when approaching a road speed camera. In addition the following enhancements are included:Voice Recognition (VR) and Bluetooth improvements. Improvements for Off-road pages.

(DTCs) This bulletin involves replacing all four wheel speed sensors due to oxidation or water intrusion into the sensor. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).M1&M6 vehicles may have one or more of the following DTCs:C0031-1D - Left Front Wheel Speed Sensor-Circuit Current Out of Range. C0034-1D - Right Front Wheel Speed Sensor-Circuit Current Out of Range. C0037-1D - Left Rear Wheel Speed Sensor-Circuit Current Out of Range. C003A-1D - Right Rear Wheel Speed Sensor-Circuit Current Out of Range. C0031-62 - Left Front Wheel Speed Sensor-Signal Compare Failure. C0034-62 - Right Front Wheel Speed Sensor-Signal Compare Failure. C0037-62 - Left Rear Wheel Speed Sensor-Signal Compare Failure. C003A-62 - Right Rear Wheel Speed Sensor-Signal Compare Failure. C0031-2F - Left Front Wheel Speed Sensor-Signal Erratic. C0034-2F - Right Front Wheel Speed Sensor-Signal Erratic. C0037-2F - Left Rear Wheel Speed Sensor-Signal Erratic. C003A-2F - Right Rear Wheel Speed Sensor-Signal Erratic. B1 vehicles may have one or more of the following DTCs:C0031-01 - Left front speed sensor - General electrical failure. C0031-29 - Left front speed sensor - Invalid signal. C0034-01 - Right front speed sensor - General electrical failure. C0034-29 - Right front speed sensor - Invalid signal. C0037-01 - Left rear speed sensor - General electrical failure. C0037-29 - Left rear speed sensor - Invalid signal. C003A-01 - Right rear speed sensor - General electrical failure. C003A-29 - Right rear speed sensor - Invalid signal.

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

If the software update is performed on a radio with software below 19.9, the radio could be damaged and will need to be replaced. Customers may experience one or more of the following:Lost radio presets. Radio display screen is black when the ignition is on. Radio may reset, turn itself off and then back on again. Park assist chime will continue to chime after the vehicle is turn off. Radio will display the incorrect speed limit in kph when approaching a road speed camera. In addition the following enhancements are included:Voice Recognition (VR) and Bluetooth improvements. Improvements for Off-road pages.

(DTCs) This bulletin involves replacing all four wheel speed sensors due to oxidation or water intrusion into the sensor. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).M1&M6 vehicles may have one or more of the following DTCs:C0031-1D - Left Front Wheel Speed Sensor-Circuit Current Out of Range. C0034-1D - Right Front Wheel Speed Sensor-Circuit Current Out of Range. C0037-1D - Left Rear Wheel Speed Sensor-Circuit Current Out of Range. C003A-1D - Right Rear Wheel Speed Sensor-Circuit Current Out of Range. C0031-62 - Left Front Wheel Speed Sensor-Signal Compare Failure. C0034-62 - Right Front Wheel Speed Sensor-Signal Compare Failure. C0037-62 - Left Rear Wheel Speed Sensor-Signal Compare Failure. C003A-62 - Right Rear Wheel Speed Sensor-Signal Compare Failure. C0031-2F - Left Front Wheel Speed Sensor-Signal Erratic. C0034-2F - Right Front Wheel Speed Sensor-Signal Erratic. C0037-2F - Left Rear Wheel Speed Sensor-Signal Erratic. C003A-2F - Right Rear Wheel Speed Sensor-Signal Erratic. B1 vehicles may have one or more of the following DTCs:C0031-01 - Left front speed sensor - General electrical failure. C0031-29 - Left front speed sensor - Invalid signal. C0034-01 - Right front speed sensor - General electrical failure. C0034-29 - Right front speed sensor - Invalid signal. C0037-01 - Left rear speed sensor - General electrical failure. C0037-29 - Left rear speed sensor - Invalid signal. C003A-01 - Right rear speed sensor - General electrical failure. C003A-29 - Right rear speed sensor - Invalid signal.

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

flash drive(s) to update the radio software level to 39.2.It is critical that every step of the bulletin is reviewed and performed properly. If any steps are missed the radio can be damaged and may need to be replaced. Customers may experience one or more of the following:If the language is set in Spanish, and the customer tries to search for an address with Voice Recognition (VR), it will not recognize these locations.VR can not find street names / location in Catalan language (present in Barcelona area and nearby). To correct this symptom, the radio SW has to be at QR39.2 and the Nav Map SW version has to be at 19Q2. In the Uconnect App, under Live>Jeep Skills>Indicator, the ?Current? meter will display the incorrect amperage readings.The battery current indicator will display the incorrect value, it will show the number 65536, stating that it is exactly in the full range scale. Audio inoperative. No audio from any media source. No audio from navigation prompts. No audio from cell or initial message prompt.The audio/sound will continue to work properly for the chimes and touchscreen beeps. Lost preset issue. The soft key for the heated seats and heated steering wheel are grayed out on the display screen and these features do not work. If the vehicle has been turned off for a long time, the settings for auto folding side mirrors is turned off (2018). Radio resets intermittently (2018). Radio display screen locks up (2018). Park assist chime will continue to chime, after the vehicle is turned off (2018). Radio will display the incorrect speed limit in kph, when approaching a road speed camera (2018). Uconnect Live feature may not function properly (2018).

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

(DTCs) This bulletin involves replacing all four wheel speed sensors due to oxidation or water intrusion into the sensor. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).B1 vehicles may have the following DTCs:C0031-01 - Left front speed sensor - General electrical failure. C0031-29 - Left front speed sensor - Invalid signal. C0034-01 - Right front speed sensor - General electrical failure. C0034-29 - Right front speed sensor - Invalid signal. C0037-01 - Left rear speed sensor - General electrical failure. C0037-29 - Left rear speed sensor - Invalid signal. C003A-01 - Right rear speed sensor - General electrical failure. C003A-29 - Right rear speed sensor - Invalid signal. M1 vehicles may have the following DTCs:C0031-1D - Left Front Wheel Speed Sensor-Circuit Current Out of Range. C0034-1D - Right Front Wheel Speed Sensor-Circuit Current Out of Range. C0037-1D - Left Rear Wheel Speed Sensor-Circuit Current Out of Range. C003A-1D - Right Rear Wheel Speed Sensor-Circuit Current Out of Range. C0031-62 - Left Front Wheel Speed Sensor-Signal Compare Failure. C0034-62 - Right Front Wheel Speed Sensor-Signal Compare Failure. C0037-62 - Left Rear Wheel Speed Sensor-Signal Compare Failure. C003A-62 - Right Rear Wheel Speed Sensor-Signal Compare Failure. C0031-2F - Left Front Wheel Speed Sensor-Signal Erratic. C0034-2F - Right Front Wheel Speed Sensor-Signal Erratic. C0037-2F - Left Rear Wheel Speed Sensor-Signal Erratic. C003A-2F - Right Rear Wheel Speed Sensor-Signal Erratic.

Unable To Shut Off Ignition, EVIC Displays Service Passive Entry

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Locations At The DLC (Diagnostic Link Connector) And BUS Test Values At DLC

(PCM) with the latest available software.

(PCM) with the latest available software.

(PCM) with the latest available software.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

control module with the latest available software. The customer may describe one of the following:Not all blower speeds are working. Lose their user settings for the (temperature, distribution and blower speed) after a on/off key cycle.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay connectivity improvement. Improvement to Bluetooth phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.

Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from IR22.64 and IR22.65 to IR22.66. The national launch for the FOTA is expected to begin on January 09, 2023. ? Wi-Fi hotspot connection not working. ? No internet connection message on the phone when trying to connect to a device

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay connectivity improvement. Improvement to Bluetooth phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

may experience the following:Radio changes distance, temperature and time format, after a network deep sleep.

may experience the following:Radio changes distance, temperature and time format, after a network deep sleep.

published document)

published document)

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay connectivity improvement. Improvement to Bluetooth phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.

may experience the following:Radio changes distance, temperature and time format, after a network deep sleep.

may experience the following:Radio changes distance, temperature and time format, after a network deep sleep.

level to:22.6 - DS, D2, DP, DD, DF and DJ vehicle with UAS, UCQ and UAQ radio. 22.5 - LA, LD and LX vehicle with UAS and UAQ. 21.9 - All other vehicles and radios. Customers may experience one or more of the following:Audio Distortion (DS, D2, DP, DD, DF and DJ vehicle with UAS, UCQ and UAQ radio). Menu bar at the bottom of the radio display is frozen (LA, LD and LX with UAQ and UAS radios). Can not change the time on the clock (LA, LD and LX with UAS radios). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio resets intermittently. Unable to adjust volume. Radio will not switch modes between AM, FM, SAT or Media. In addition, the following enhancements are included in this update:Carplay connectivity improvements. Improvement to Bluetooth phone pairing. Improved sound quality when using a Bluetooth phone.

level to:28.3 - WD and WK vehicle with UAQ and UCQ radio. 22.6 - DS, D2, DP, DD, DF and DJ vehicle with UAS, UCQ and UAQ radio. 22.5 - LA, LD and LX vehicle with UAS and UAQ. 21.9 - All other vehicles and radios. Customers may experience one or more of the following:Warning chime will not turn off (WD and WK with UAQ and UCQ radio). Audio Distortion (DS, D2, DP, DD, DF and DJ vehicle with UAS, UCQ and UAQ radio). Menu bar at the bottom of the radio display is frozen (LA, LD and LX with UAQ and UAS radios). Can not change the time on the clock (LA, LD and LX with UAS radios). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio resets intermittently. Unable to adjust volume. Radio will not switch modes between AM, FM, SAT or Media. In addition, the following enhancements are included in this update:Bluetooth improvements (WD and WK with UAQ and UCQ radio). Voice Recognition (VR) improvements (WD and WK with UAQ and UCQ radio). Radio stability improvements (WD and WK with UAQ and UCQ radio). Carplay connectivity improvements. Improvement to Bluetooth phone pairing. Improved sound quality when using a Bluetooth phone.

level to:22.6 - DS, D2, DP, DD, DF and DJ vehicle with UAS, UCQ and UAQ radio. 22.5 - LA, LD and LX vehicle with UAS and UAQ. 21.9 - All other vehicles and radios. Customers may experience one or more of the following:Audio Distortion (DS, D2, DP, DD, DF and DJ vehicle with UAS, UCQ and UAQ radio). Menu bar at the bottom of the radio display is frozen (LA, LD and LX with UAQ and UAS radios). Can not change the time on the clock (LA, LD and LX with UAS radios). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio resets intermittently. Unable to adjust volume. Radio will not switch modes between AM, FM, SAT or Media. In addition, the following enhancements are included in this update:Carplay connectivity improvements. Improvement to Bluetooth phone pairing. Improved sound quality when using a Bluetooth phone.

level to 21.9. Customers may experience one or more of the following:If the vehicle has been turned off for a long time, the settings for auto folding side mirrors is turned off Radio resets intermittently. Radio display screen locks up. Park assist chime will continue to chime, after the vehicle is turned off. Radio will display the incorrect speed limit in kph, when approaching a road speed camera. Uconnect Live feature may not function properly.

Customers may experience one or more of the following:If the vehicle has been turned off for a long time, the settings for auto folding side mirrors is turned off Radio resets intermittently. Radio display screen locks up. Park assist chime will continue to chime, after the vehicle is turned off. Radio will display the incorrect speed limit in kph, when approaching a road speed camera. Uconnect Live feature may not function properly.

pressure low indicator lamp illumination between oil changes. Excessive oil consumption This bulletin involves performing an oil consumption verification test and possibly replacing the long block. "

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block."

pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)

installed in the vehicle.

with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set: P1D7F-00 - ETC Self-Learning Failure.(North America only). P0456-00 - EVAP Purge System Small Leak.(North America only). P0441-00 - EVAP Purge System Performance.(North America only). P0440-00 - General EVAP System Failure. (North America only). P0455-00 - EVAP Purge System Large Leak.(North America only). P1CEA-00 - Boost Side EVAP Purge System Performance.(North America only). In addition, the following software enhancement is available: After a short trip and shutting the engine off for 5-10 minutes, vehicle exhibits a long crank/start condition(EMEA only). Updated EVAP system diagnostics.(North America only).

oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0456 - EVAP System Small Leak. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0016 - Crankshaft/Camshaft Timing Misalignment - Bank 1 Sensor 1. P0606 - Control Module Processor. Customers may also experience the following:Vehicle periodically may fail to start(ED6 engine only).

involves installing a modified oil vapor inlet tube. The customer may describe a loss in vehicle performance (engine jerking or limp mode) and/or a malfunction indicator light (MIL) illuminated.The following Diagnostic Trouble Code (DTC):P2173-00 - Air Leakage In Manifold (Signal Compare Failure).

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set: P1D7F-00 - ETC Self-Learning Failure.(North America only). P0456-00 - EVAP Purge System Small Leak.(North America only). P0441-00 - EVAP Purge System Performance.(North America only). P0440-00 - General EVAP System Failure. (North America only). P0455-00 - EVAP Purge System Large Leak.(North America only). P1CEA-00 - Boost Side EVAP Purge System Performance.(North America only). In addition, the following software enhancement is available: After a short trip and shutting the engine off for 5-10 minutes, vehicle exhibits a long crank/start condition(EMEA only). Updated EVAP system diagnostics.(North America only).

with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set: P1D7F-00 - ETC Self-Learning Failure.(North America only). P0456-00 - EVAP Purge System Small Leak.(North America only). P0441-00 - EVAP Purge System Performance.(North America only). P0440-00 - General EVAP System Failure. (North America only). P0455-00 - EVAP Purge System Large Leak.(North America only). P1CEA-00 - Boost Side EVAP Purge System Performance.(North America only). In addition, the following software enhancement is available: After a short trip and shutting the engine off for 5-10 minutes, vehicle exhibits a long crank/start condition(EMEA only). Updated EVAP system diagnostics.(North America only).

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0456 - EVAP System Small Leak. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0016 - Crankshaft/Camshaft Timing Misalignment - Bank 1 Sensor 1. P0606 - Control Module Processor. Customers may also experience the following:Vehicle periodically may fail to start(ED6 engine only).

involves installing a modified oil vapor inlet tube. The customer may describe a loss in vehicle performance (engine jerking or limp mode) and/or a malfunction indicator light (MIL) illuminated.The following Diagnostic Trouble Code (DTC):P2173-00 - Air Leakage In Manifold (Signal Compare Failure).

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

installed in the vehicle.

Customers may experience one or more of the following:The language switches to Italian. The language switches to English when ignition cycles. Heated/Vent Seat and Heated Steering wheel icon are grayed out on display screen during Ignition ?ON? and when engine in ?RUN? state. Making it impossible to activate/deactivate them until shutting the engine off.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure (Software has been updated to better address this DTC). In addition, the customer may notice the following condition(s): Service Passive Entry Light" on cluster and MIL code B1053-64. Vehicle will not shut off with DTC B1053-64. Vehicle may not start with DTC B1053-64. With the ignition in the run position and the engine not running, the vehicle may not turn itself off after 30 minutes. Doors may not unlock when using the Remote Keyless Entry (RKE) Fob.(2015 only) Tire pressure monitoring (TPM) light may illuminate when using the winter tires in winter mode functionality.(2015-2016 only) After an engine start and the doors are closed, a message in the cluster may be displayed ?Key Not Detected? when the key is actually present.(2015-2016 only) Only a message is displayed, the vehicle will start.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) have been set: P1D7F-00 - ETC Self-Learning Failure.(North America only). P0456-00 - EVAP Purge System Small Leak.(North America only). P0441-00 - EVAP Purge System Performance.(North America only). P0440-00 - General EVAP System Failure. (North America only). P0455-00 - EVAP Purge System Large Leak.(North America only). P1CEA-00 - Boost Side EVAP Purge System Performance.(North America only). In addition, the following software enhancement is available: After a short trip and shutting the engine off for 5-10 minutes, vehicle exhibits a long crank/start condition(EMEA only). Updated EVAP system diagnostics.(North America only).

Customers may experience one or more of the following:The language switches to Italian. The language switches to English when ignition cycles. Heated/Vent Seat and Heated Steering wheel icon are grayed out on display screen during Ignition ?ON? and when engine in ?RUN? state. Making it impossible to activate/deactivate them until shutting the engine off.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:B1053-64 RFHM (Keyless Ignition Node (KIN) Communication) - Signal Plausibility Failure (Software has been updated to better address this DTC). In addition, the customer may notice the following condition(s): Service Passive Entry Light" on cluster and MIL code B1053-64. Vehicle will not shut off with DTC B1053-64. Vehicle may not start with DTC B1053-64. With the ignition in the run position and the engine not running, the vehicle may not turn itself off after 30 minutes. Doors may not unlock when using the Remote Keyless Entry (RKE) Fob.(2015 only) Tire pressure monitoring (TPM) light may illuminate when using the winter tires in winter mode functionality.(2015-2016 only) After an engine start and the doors are closed, a message in the cluster may be displayed ?Key Not Detected? when the key is actually present.(2015-2016 only) Only a message is displayed, the vehicle will start.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0456 - EVAP System Small Leak. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0016 - Crankshaft/Camshaft Timing Misalignment - Bank 1 Sensor 1. P0606 - Control Module Processor. Customers may also experience the following:Vehicle periodically may fail to start(ED6 engine only).

involves installing a modified oil vapor inlet tube. The customer may describe a loss in vehicle performance (engine jerking or limp mode) and/or a malfunction indicator light (MIL) illuminated.The following Diagnostic Trouble Code (DTC):P2173-00 - Air Leakage In Manifold (Signal Compare Failure).

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may describe the following:The heated steering wheel and heated seats, turn off when Engine Stop Start (ESS) activates.

The customer may describe the following:After starting the vehicle with remote start, the engine stops when the doors are unlocked.

The customer may describe the following:After starting the vehicle with remote start, the engine stops when the doors are unlocked.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

The customer may describe the following:The heated steering wheel and heated seats, turn off when Engine Stop Start (ESS) activates.

The customer may describe the following:After starting the vehicle with remote start, the engine stops when the doors are unlocked.

The customer may describe the following:After starting the vehicle with remote start, the engine stops when the doors are unlocked.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

The customer may describe the following:The heated steering wheel and heated seats, turn off when Engine Stop Start (ESS) activates.

The customer may describe the following:After starting the vehicle with remote start, the engine stops when the doors are unlocked.

The customer may describe the following:After starting the vehicle with remote start, the engine stops when the doors are unlocked.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set:P0238-00 - Positive Boost Pressure Governor Deviation Low Pressure Signal Calculation Failure. Customer may also notice:Erratic engine idle. Premature alternator pulley failure. Other software enhancements include:Improvement to avoid soot formation in the intake system that can cause engine speed oscillation at idle. Improvement to the alternator strategy to prevent alternator pulley failure.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

Customers may experience excessive oil consumption between oil change intervals.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0456 - EVAP System Small Leak. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0016 - Crankshaft/Camshaft Timing Misalignment - Bank 1 Sensor 1. P0606 - Control Module Processor.

Some customers may experience the following condition:When pressing the SPORT button on the console, the SPORT mode is not activated. Hard to start condition at low temperatures 10-15C (50-60F) and filled with 70~80% ethanol fuel (DF7 Transmission Sales Code only). Engine experiencing a hard re-start after being shut off for short periods of time. Engine Stop/Start (ESS) remains in stop condition and they must manually restart the engine due to either a door or the hood being opened while in ESS mode.

Order the "R" part number for all orders:

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Detected Message

awareness regarding the use of aftermarket parts.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

1. This bulletin involves replacing the window seal and glass.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

plastic panels and applying corrosion protection.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

The customer may describe a crank, no start condition, in freezing temperatures. This condition can be caused by condensation freezing in the muffler assembly.

The customer may describe a crank, no start condition, in freezing temperatures. This condition can be caused by condensation freezing in the muffler assembly.

The customer may describe a crank, no start condition, in freezing temperatures. This condition can be caused by condensation freezing in the muffler assembly.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.

DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure. This software update also includes the following enhancementsReduce Rear Drive Module (RDM) noise during disconnect phase at speeds above 45 kph (28 mph)North America Only.

DTCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):C2502-64 - Signal Plausibility Failure. C2210-92 - ETM Hall Sensor Performance Or Incorrect Operation. C2220-54 - ETM Calibration Error Missing Calibration. C2020-01 - ECU Internal Fault - General Electrical Failure. This software update also includes the following enhancementsReduce Rear Drive Module (RDM) noise during disconnect phase at speeds above 45 kph (28 mph)North America Only.

Customers may experience the following:Erratic or inconsistent shifting. Software enhancements include:Improved shift enhancements due to PCM improvements.

Customers may experience the following: Malfunction Indicator Lamp (MIL) illumination, Electronic Vehicle Information Center (EVIC) message states ?Service Transmission? and transmission intermittently goes into neutral with PRNDL flashing when vehicle is stopped. The vehicle may or may not resume normal transmission operation after cycling the shifter or ignition.

B)

EVIC Displays Service Passive Entry

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

EVIC Displays Service Passive Entry

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order a "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

industry awareness regarding the use of recycled or salvage parts.

assembly, it is not required for service. 2AMV8043A$ can be used for this application.

assembly, it is not required for service. 2AMV8043A$ can be used for this application.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.