2011 Jeep Liberty TSBs

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following DTCs set in the PCM memory: **U0140 - Lost Communication With Body Control Module (BCM) (10-12 MY only). Auto Shutdown (ASD) Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (10-12 MY only).** P0401 - EGR System Performance. In addition the customer may notice one of the following conditions: Hard to start, long crank time or even a no start. The customer may describe that If the gas pedal is pushed slightly the vehicle starts as expected (11 MY KA only).

flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Customer may experience a condition where the clock will lose over one minute a month.

Customer may experience a condition where the clock will lose over one minute a month.

Customer may experience a condition where the clock will lose over one minute a month.

Customer may experience a condition where the clock will lose over one minute a month.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Customer may experience a condition where the clock will lose over one minute a month.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Powertrain Control Module (PCM) with new software. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 37-62 mph (60-100 km/h). Some customers may also describe the sensation similar to that of a fish biting on a fishing line (fishbite) .If the customer complains of the above condition, perform the Repair Procedure.

occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality (examples may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the following:~ 1. Power on radio~2. Press MENU H/K~3. Press System Setup S/K~4. Press Manage HDD S/K~5. Press Display Available Space on HDD S/K~6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes~ Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. ~ Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.

Customer may experience a condition where the clock will lose over one minute a month.

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following DTCs set in the PCM memory: **U0140 - Lost Communication With Body Control Module (BCM) (10-12 MY only). Auto Shutdown (ASD) Relay Enhancements To Improve Fuel Pump Relay Initialization At Key On - (10-12 MY only).** P0401 - EGR System Performance. In addition the customer may notice one of the following conditions: Hard to start, long crank time or even a no start. The customer may describe that If the gas pedal is pushed slightly the vehicle starts as expected (11 MY KA only).

2011 LIBERTY. *RM

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

if necessary, adjusting seals and/or left and/or right front door striker to eliminate high closing effort. The customer may experience high closing efforts on the left and/or right front doors when closing.

and if necessary sealing the right and/or left roof ditch. The customer may notice the headliner is wet in either the right or left rear corners.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

if necessary, adjusting seals and/or left and/or right front door striker to eliminate high closing effort. The customer may experience high closing efforts on the left and/or right front doors when closing.

and if necessary sealing the right and/or left roof ditch. The customer may notice the headliner is wet in either the right or left rear corners.

if necessary, adjusting seals and/or left and/or right front door striker to eliminate high closing effort. The customer may experience high closing efforts on the left and/or right front doors when closing.

and if necessary sealing the right and/or left roof ditch. The customer may notice the headliner is wet in either the right or left rear corners.

if necessary, adjusting seals and/or left and/or right front door striker to eliminate high closing effort. The customer may experience high closing efforts on the left and/or right front doors when closing.

and if necessary sealing the right and/or left roof ditch. The customer may notice the headliner is wet in either the right or left rear corners.

THE RIGHT FRONT AND REAR DOOR LATCH MAY HAVE A RATCHET SOUND WHILE USING THE POWER DOOR LOCKS. *RM

semi and full synthetic oils.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

(KA)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan/Chrysler Town & Country (RT), Dodge Durango (WD), Jeep Grand Cherokee (WK) (Rev. A)

Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan (RT), Dodge Durango (WD), Jeep Grand Cherokee (WK)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

(KA)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

(KA)

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

The customer may experience one or more of the following conditions. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

Library for specifications so a suitable alternative can be used

and Customer Concern (CC) failure codes.