2012 Jeep Grand Cherokee TSBs

this is normal and not a defect.

this is normal and not a defect.

semi and full synthetic oils.

bracket (68100737AA).~ Replace old shield (1UP58TRMAA) with new shield (1XN08TRMAA) and bracket (68100737AA).~ Replace old shield (1UQ14TRMAA) with new shield (1XN96TRMAA) and bracket (68100737AA).~ The new bracket (68100737AA) is only needed if the vehicle doesn't already have it (check PN on phyical part)

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

bracket (68100737AA).~ Replace old shield (1UP58TRMAA) with new shield (1XN08TRMAA) and bracket (68100737AA).~ Replace old shield (1UQ14TRMAA) with new shield (1XN96TRMAA) and bracket (68100737AA).~ The new bracket (68100737AA) is only needed if the vehicle doesn't already have it (check PN on phyical part)

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Also Includes Powertrain System Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience the following condition: Engine is difficult to start in extreme cold ambient temps when using the block heater. This release improves the spark and fueling strategy used under these conditions.The following system improvements have also been included in this software release: Improved Electronic Voltage Regulator control to more precisely maintain system voltage.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

and if necessary replacing the hinge pivot bolt. The customer may experience a knocking sound from the instrument panel area near the A-pillar.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

air spring bellows and piston area at the lower control arm pocket in the rear of the vehicle. Rear suspension air springs may become damaged due to abrasion from road debris or the air spring can become punctured due to ice/snow build-up at bottom of piston at lower control arm.

Door Modules (DMFL/DMFR) with new software. The power folding mirrors may unfold while cranking the engine.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.

A small number of customers may report the MIL light is on. On further inspection Diagnostic Trouble Code (DTC), P0405 - EGR POSITION SENSOR CIRCUIT LOW and/or P0406 - EGR POSITION SENSOR CIRCUIT HIGH may be found.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

Also Includes Powertrain System Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience the following condition: Engine is difficult to start in extreme cold ambient temps when using the block heater. This release improves the spark and fueling strategy used under these conditions.The following system improvements have also been included in this software release: Improved Electronic Voltage Regulator control to more precisely maintain system voltage.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

reprogramming the Transmission Control Module (TCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find that Diagnostic Trouble Code (DTC) P0730 Incorrect Gear Ratio is setting erroneously. In addition to correcting the DTC, the following Transmission Control Module (TCM) calibration improvements are now available. These updates are broken down by vehicle line and engine category.WK, WD, JK and LC Vehicles equipped with a 3.6L engine (Sales Code ERB) Hanging in gear during HOT ambient temperature conditions while vehicle is loaded or towing. Delayed downshift during acceleration at speeds above 48 kph. (Taiwan, Japan, and China market only). Delayed downshift when driving at altitudes higher than 2500 feet. Inconsistent shifting when towing or while driving up or down steep hills. Delayed upshift while driving in 4 low Intermittent delayed shift. Delayed engagement when shifting from drive to reverse while in 4 low. (JK Rubicon only) Delayed shift from second gear while towing or driving on steep grades. (JK Rubicon only) Intermittent delayed engagement from reverse to drive. Less than desired shift quality in AutoStick mode. (LC vehicles only) Fuel economy improvements. (LC vehicles only)LC Vehicles equipped with a 5.7L engine (Sales Codes EZH or EZC) Hanging in gear during HOT ambient temperature conditions while vehicle is loaded or towing. Bump sensation felt during deceleration or braking. Fuel economy improvements.LC and WK Vehicles equipped with a 6.4L engine (Sales Codes ESH or ESG) Bump sensation felt during deceleration or braking. (LC only) Inconsistent downshift during Wide Open Throttle (WOT) accelerations at highway speeds (i.e. passing). Transmission enhancements to improve acceleration while in reverse going uphill on steep

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements.

Slip Differential (ELSD) with new software. If any of the following DTC?s are either Active or Stored in the ELSD module?s memory, the ELSD motor will need to be replaced as well. C1490-00-REAR DIFFERENTIAL ACTUATOR INITIALIZATION FAILURE C148F-1D-REAR DIFFERENTIAL MEASURED MOTOR - CIRCUIT OUT OF RANGE C1489-96-REAR DIFFERENTIAL MOTOR BRAKE - COMPONENT INTERNAL FAILURE The customer may indicate that their 4X4 lamp may be flashing (indicating a malfunction of the 4X4 system).In addition, one or more of the following Diagnostic Trouble Codes (DTC) are Active or Stored in the ELSD control module?s memory. C1490-00-REAR DIFFERENTIAL ACTUATOR INITIALIZATION FAILURE C148F-1D-REAR DIFFERENTIAL MEASURED MOTOR - CIRCUIT OUT OF RANGE C1489-96-REAR DIFFERENTIAL MOTOR BRAKE - COMPONENT INTERNAL FAILURE

air spring bellows and piston area at the lower control arm pocket in the rear of the vehicle. Rear suspension air springs may become damaged due to abrasion from road debris or the air spring can become punctured due to ice/snow build-up at bottom of piston at lower control arm.

Door Modules (DMFL/DMFR) with new software. The power folding mirrors may unfold while cranking the engine.

and if necessary replacing the hinge pivot bolt. The customer may experience a knocking sound from the instrument panel area near the A-pillar.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.

air spring bellows and piston area at the lower control arm pocket in the rear of the vehicle. Rear suspension air springs may become damaged due to abrasion from road debris or the air spring can become punctured due to ice/snow build-up at bottom of piston at lower control arm.

Door Modules (DMFL/DMFR) with new software. The power folding mirrors may unfold while cranking the engine.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

and if necessary replacing the hinge pivot bolt. The customer may experience a knocking sound from the instrument panel area near the A-pillar.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

IN MANUAL (USER GUIDE), STATED INCORRECTLY ENGINE OIL (SAE 5W-40), INSTEAD OF CORRECTLY ENGINE OIL (SAE 0W-40 FULL SYNTHETIC ENGINE OIL. *PE

*PE

Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.

If there is no Broken Pieces or Electrical failure, Direction to follow the RESET Procedure in service Library to RESET the AHR

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Customers may describe an unpleasant odor in the vehicle after driving from highway speed limits back down to city speed limits.Updating the HVAC software will correct these conditions.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Powertrain Control Module (PCM) with new software.This is an optional software update that should only be used in situations where the customer is specifically complaining of the condition described below. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 40-80 mph (64-129 km/h). Some customers may also describe the sensation similar to that of a fish biting on a fishing line.This is an optional software update that should only be used in situations where the customer is specifically complaining of the above condition. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this SB contains the verbiage ?REFERENCE SB 18-035-14. THIS FLASH TO BE USED ONLY FOR SHUDDER COMPLAINTS?. The other file is the standard software that does not contain improvements for this complaint. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version.If the customer complains of the above condition, perform the Repair Procedure.

The customer satisfaction enhancements are included with this software release:After the HFM has been updated it will receive these enhancements. Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / Dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via MAP protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected.USB mode resume will no longer 'resume' after ignition OFF

software and adding double sided tape to secure the module. The customer may experience the theft alarm siren turning on for no reason.This could be caused by the overhead console not retaining the intrusion module in place as well as it should. With the module not properly secured and with temperature changes, the wiring stiffens and relaxes moving the module. This set?s off the alarm. Reprogramming the module is to improve sensor stability that makes it less sensitive to movement. Adding tape to the module prevents movement.

The customer may experience the Power Lift Gate not opening and closing under power. Upon further investigation the Technician may find that B1882 Power Liftgate Position Sensor 1 Circuit set.Updating the software will correct the conditions listed above.

repair to the sun visor, headliner or while gaining access above the headliner. This may result in an inoperative vanity lamp and/or an electrical fire.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Powertrain Control Module (PCM) with new software.This is an optional software update that should only be used in situations where the customer is specifically complaining of the condition described below. A small number of customers may experience a surge, shudder or pulsation type sensation when driving on smooth road surfaces at highway speeds of 40-80 mph (64-129 km/h). Some customers may also describe the sensation similar to that of a fish biting on a fishing line.This is an optional software update that should only be used in situations where the customer is specifically complaining of the above condition. There will be two separate software options displayed on the wiTECH flash tab. The software file released for this SB contains the verbiage ?REFERENCE SB 18-035-14. THIS FLASH TO BE USED ONLY FOR SHUDDER COMPLAINTS?. The other file is the standard software that does not contain improvements for this complaint. If for some reason the customer finds this shudder improvement objectionable, the PCM software may be returned/reflashed to the standard version.If the customer complains of the above condition, perform the Repair Procedure.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

The customer may experience the Power Lift Gate not opening and closing under power. Upon further investigation the Technician may find that B1882 Power Liftgate Position Sensor 1 Circuit set.Updating the software will correct the conditions listed above.

This bulletin involves selectively replacing the solar sensor. Customers may experience the following condition: When using the Automatic Temperature Control ?SYNC? mode, left and right outlet temperatures do not match regardless of the desired temperature setting is the same. Occupants will experience being cold (winter time), on either passenger or driver side, even though the temperature setting is the same. Headlamps are always staying on, when they are set to Auto mode.

The customer may experience the Power Lift Gate not opening and closing under power. Upon further investigation the Technician may find that B1882 Power Liftgate Position Sensor 1 Circuit set.Updating the software will correct the conditions listed above.

USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.

The customer satisfaction enhancements are included with this software release:After the HFM has been updated it will receive these enhancements. Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / Dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via MAP protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected.USB mode resume will no longer 'resume' after ignition OFF

software and adding double sided tape to secure the module. The customer may experience the theft alarm siren turning on for no reason.This could be caused by the overhead console not retaining the intrusion module in place as well as it should. With the module not properly secured and with temperature changes, the wiring stiffens and relaxes moving the module. This set?s off the alarm. Reprogramming the module is to improve sensor stability that makes it less sensitive to movement. Adding tape to the module prevents movement.

The customer satisfaction enhancements are included with this software release:After the HFM has been updated it will receive these enhancements. Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / Dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via MAP protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected.USB mode resume will no longer 'resume' after ignition OFF

software and adding double sided tape to secure the module. The customer may experience the theft alarm siren turning on for no reason.This could be caused by the overhead console not retaining the intrusion module in place as well as it should. With the module not properly secured and with temperature changes, the wiring stiffens and relaxes moving the module. This set?s off the alarm. Reprogramming the module is to improve sensor stability that makes it less sensitive to movement. Adding tape to the module prevents movement.

The customer may experience the Power Lift Gate not opening and closing under power. Upon further investigation the Technician may find that B1882 Power Liftgate Position Sensor 1 Circuit set.Updating the software will correct the conditions listed above.

*PE

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

mechanism and seat back panel crossmember. Customers may describe a chirping or squeaking coming from the rear second row seat headrest(s) while driving.

leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.

leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

creak, click or rattle and if necessary, replacing the dual pane sunroof frame assembly. The customer may experience a creak, click or rattle from the dual pane sunroof.

Sunroof Drain Tube Inspection.

and if necessary adding grease and, depending on build range, RTV to both rear jounce bumpers. Squeak and/or creak sound coming from rear of vehicle when driving over rough roads.

leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.

leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.

leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.

leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.

leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.

leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

trim appliques that have suffered delamination issues. Some customers may comment on one of the following: The carbon fiber inner doors and instrument panel appliques are delaminating. The outer layer of a carbon fiber applique is separating from the inner layer.

mechanism and seat back panel crossmember. Customers may describe a chirping or squeaking coming from the rear second row seat headrest(s) while driving.

creak, click or rattle and if necessary, replacing the dual pane sunroof frame assembly. The customer may experience a creak, click or rattle from the dual pane sunroof.

creak, click or rattle and if necessary, replacing the dual pane sunroof frame assembly. The customer may experience a creak, click or rattle from the dual pane sunroof.

INFORMATION BEING PROVIDED REGARDING DELAMINATION OF INSTRUMENT AND DOOR PANEL CARBON FIBER BEZEL APPLIQUES FROM BEZEL AND MUST BE INSPECTED AND REPLACED, IF NECESSARY. MODELS 2012 GRAND CHEROKEE. *PE

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

necessary replace the front brake pads. Squeal noise from front of vehicle when braking.

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

The rear shocks may produce a rattle chuckle noise while driving over bumps at low speed. The noise is more prevalent at higher shock temperatures.

Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.

Rattle and/or clunk noise from the rear of the vehicle equipped with load leveling suspension.

necessary replace the front brake pads. Squeal noise from front of vehicle when braking.

Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.

Rattle and/or clunk noise from the rear of the vehicle equipped with load leveling suspension.

The customer may describe a front brake squeak/squeal noise at cold temperatures or with cold brakes after sitting. Noise is most prevalent during a low-speed stop with light brake pedal effort.

The customer may describe a high frequency front brake squeal or squeak, at approximately 8.4kHz. Noise may be intermittent, so not always possible to duplicate.

The rear shocks may produce a rattle chuckle noise while driving over bumps at low speed. The noise is more prevalent at higher shock temperatures.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

involves road testing and if necessary replacing the intermediate shaft. Clunk and/or bump felt through the steering wheel under moderate braking or driving over rough roads. This can be caused by spline stick/slip from the intermediate shaft.

2011 through 2014 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. Some Jeep Grand Cherokee and Dodge Durango vehicles may have a brake booster that could prematurely corrode. If perforation of the brake booster shell (due to corrosion) occurs, the brake booster may ingest water during vehicle operation during wet weather conditions. A brake booster that has experienced water ingestion may have the brake function compromised if the water inside the brake booster freezes. The driver may be required to apply additional application force to apply the brakes during sub-freezing driving conditions. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to inspect the brake booster for corrosion. Brake boosters found with excessive corrosion will be replaced. All boosters will be equipped with a shield to protect the brake booster crimp joints from water exposure. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

2012 and 2013 model year (WD) Dodge Durango and (WK) Jeep Grand Cherokee vehicles. The brake pedal may require additional application force to apply the brakes during certain braking events. An unexpected additional brake pedal application force requirement could slow the driver?s brake application reaction time and cause a crash without warning. Chrysler will conduct a voluntary safety recall on all involved vehicles to reprogram the Antilock Brake System (ABS) module. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. Chrysler anticipates the launch of this safety recall in March 2014. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

necessary replace the front brake pads. Squeal noise from front of vehicle when braking.

SQUEAK *CN

Customers may experience a condition were new roads and new point of interests are not accurately shown on their navigation system.Updating the navigation software will help address most of the map inaccurate results.

The customer may experience one or more of the following conditions. Digital photos loaded onto the hard drive intermittently get lost (RBZ & RHB). CD/DVD will not play (RHB only). Navigation accept screen will not clear (RHB only). Navigation shows ?acquiring signal? for an extended period of time (RHB only). New navigation graphics (RHB only).

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. SYMPTOM/CONDITION FOR RHB RADIOS ONLY: ? Trip planner does not save a route after is was created. ? Route guidance does not activate after the vehicle shuts down. ? Longitude entry does not allow enough digits. ? CD/DVD will not play. ? Navigation accept screen will not clear. ? Navigation shows ?acquiring signal? for an extended period of time. ? New navigation graphics.

The customer may experience one or more of the following. When changing the language on the radio, the navigation may still display English. Help prevent navigation lockup. Ghost image of the vehicle?s brand logo on the display screen. Digital photos loaded onto the hard drive intermittently get lost. Sirius audio pop on power up. HFM audio pop on power up. HFM Mode resume with no information.SYMPTOM/CONDITION FOR RHB RADIOS ONLY: Trip planner does not save a route after is was created. Route guidance does not activate after the vehicle shuts down. Longitude entry does not allow enough digits. CD/DVD will not play. Navigation accept screen will not clear. Navigation shows ?acquiring signal? for an extended period of time. New navigation graphics.

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? CD/DVD will not play (RHB only). ? Navigation accept screen will not clear (RHB only). ? Navigation shows ?acquiring signal? for an extended period of time (RHB only). ? New navigation graphics (RHB only). ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. ? Trip planner does not save a route after is was created (RHB only). ? Route guidance does not activate after the vehicle shuts down (RHB only). ? Longitude entry does not allow enough digits (RHB only).

The customer may experience one or more of the following conditions. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

Customers may experience a condition were new roads and new point of interests are not accurately shown on their navigation system.Updating the navigation software will help address most of the map inaccurate results.

The customer may experience one or more of the following conditions. Digital photos loaded onto the hard drive intermittently get lost (RBZ & RHB). CD/DVD will not play (RHB only). Navigation accept screen will not clear (RHB only). Navigation shows ?acquiring signal? for an extended period of time (RHB only). New navigation graphics (RHB only).

Customers may experience a condition were new roads and new point of interests are not accurately shown on their navigation system.Updating the navigation software will help address most of the map inaccurate results.

The customer may experience one or more of the following conditions. Digital photos loaded onto the hard drive intermittently get lost (RBZ & RHB). CD/DVD will not play (RHB only). Navigation accept screen will not clear (RHB only). Navigation shows ?acquiring signal? for an extended period of time (RHB only). New navigation graphics (RHB only).

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.

D)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

C)

B)

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

Customers may indicate that the MIL is illuminated and/or the transmission went into limp-in. Upon further investigation, Diagnostic Trouble Code (DTC) P0730 - Incorrect Gear Ratio is either active or stored in the PCM?s memory.

Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:A driveline bump is felt during acceleration at approximately 10 mph (16 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 - 5 mph (5 - 8 kph).

Customers may indicate that the MIL is illuminated and/or the transmission went into limp-in. Upon further investigation, Diagnostic Trouble Code (DTC) P0730 - Incorrect Gear Ratio is either active or stored in the PCM?s memory.

Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:A driveline bump is felt during acceleration at approximately 10 mph (16 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 - 5 mph (5 - 8 kph).

Customers may indicate that the MIL is illuminated and/or the transmission went into limp-in. Upon further investigation, Diagnostic Trouble Code (DTC) P0730 - Incorrect Gear Ratio is either active or stored in the PCM?s memory.

Drivetrain Control Module (DCTM) Owners may indicate that they have experienced one or more of the following symptoms:A driveline bump is felt during acceleration at approximately 10 mph (16 kph).The SERV 4WD message appears and the vehicle shifts from 4WD to 2WD.Binding of the front driveline while turning on steep grades at speeds around 3 - 5 mph (5 - 8 kph).

updated "Hub & Bearing Noise Diagnostic Procedure", found in STAR News #75 and in Service Manual. See DealerCONNECT>TechCONNECT>Service Info>Rear Susp>Hub and Bearing>Diagnosis and Testing>Diagnosis and Testing - Hub and Bearing - Noise.

updated "Hub & Bearing Noise Diagnostic Procedure", found in STAR News #75 and in Service Manual. See DealerCONNECT>TechCONNECT>Service Info>Rear Susp>Hub and Bearing>Diagnosis and Testing>Diagnosis and Testing - Hub and Bearing - Noise.

updated "Hub & Bearing Noise Diagnostic Procedure", found in STAR News #75 and in Service Manual. See DealerCONNECT>TechCONNECT>Service Info>Rear Susp>Hub and Bearing>Diagnosis and Testing>Diagnosis and Testing - Hub and Bearing - Noise.

The EGR coolant hose may weep coolant.

The EGR coolant hose may weep coolant.

Customer may describe a lead or drift to the right condition at steady state speeds at 35 MPH and above.

Customer may describe a lead or drift to the left condition at steady state speeds of 56 KPH (35 MPH) and above.

Customer may describe a lead or drift to the right condition at steady state speeds at 35 MPH and above.

Customer may describe a lead or drift to the left condition at steady state speeds of 56 KPH (35 MPH) and above.

Customer may describe a lead or drift to the right condition at steady state speeds at 35 MPH and above.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

procedures outlined in CSN P49.

Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.

variation and flat spotting removal SPECIAL TOOLS/EQUIPMENT REQUIRED: (1) Hunter GSP9700 Road Force Diagnostic System

Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.

Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star. UPDATE: 11/9/2016 If the new bearing does not fit through the double dash, you need to replace the lower double dash panel to the latest level. Please see the updated flowchart in StarParts for the correct replacement panel.

WHILE DRIVING OVER ROUGH ROADS , EXPERIENCING BUMPENESS OR CLUNKING UNDER STEERING WHEEL. *LJ

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.