2005 Jeep Grand Cherokee TSBs

software on about 295,600 of the above vehicles may cause the ?Service 4WD? light to come on and an inability to switch 4WD mode when trying to shift out of the current selected mode. The Final Drive Control Module (FDCM) must be reprogrammed with new software.

bulletin involves verifying FDCM software level and then flash reprogramming of the FDCM with new software. Customers may indicate that the ?Service 4WD? indicator in the instrument cluster is illuminated. They may also indicate that the transfer case will not shift from 4WD High, 4WD Low, and/or Neutral once the lamp is illuminated. Further investigation identifies that a Diagnostic Trouble Code C140F is stored or active in the Final Drive Control Modules (FDCM) Memory

bulletin involves verifying FDCM software level and then flash reprogramming of the FDCM with new software. Customers may indicate that the ?Service 4WD? indicator in the instrument cluster is illuminated. They may also indicate that the transfer case will not shift from 4WD High, 4WD Low, and/or Neutral once the lamp is illuminated. Further investigation identifies that a Diagnostic Trouble Code C140F is stored or active in the Final Drive Control Modules (FDCM) Memory

2005 - 2010 model year (WK) Jeep Grand Cherokee and (XK) Jeep Commander vehicles equipped with a Quadra-Drive II or Quadra-Trac II four wheel drive system. Some of the above vehicles may experience a transfer case actuator encoder electrical failure that results in unintentional transfer case shifting into or through the neutral position. NOTE: These vehicles are equipped with a NV245 transfer case that is part of the automatic four wheel drive system. The transfer case shifts into and out of four wheel drive modes and ranges automatically or based on driver inputs. Chrysler will conduct a voluntary safety recall on all affected vehicles to reprogram the Final Drive Controller Module (FDCM) with new software. The four wheel drive system will then be function tested. Vehicles found with an inoperative transfer case actuator will also have the actuator replaced. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

2005 - 2010 model year (WK) Jeep Grand Cherokee and (XK) Jeep Commander vehicles equipped with a Quadra-Drive II or Quadra-Trac II four wheel drive system. Some of the above vehicles may experience a transfer case actuator encoder electrical failure that results in unintentional transfer case shifting into or through the neutral position. NOTE: These vehicles are equipped with a NV245 transfer case that is part of the automatic four wheel drive system. The transfer case shifts into and out of four wheel drive modes and ranges automatically or based on driver inputs. Chrysler will conduct a voluntary safety recall on all affected vehicles to reprogram the Final Drive Controller Module (FDCM) with new software. The four wheel drive system will then be function tested. Vehicles found with an inoperative transfer case actuator will also have the actuator replaced. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

software on about 295,600 of the above vehicles may cause the service 4WD light to come on and an inability to switch 4WD mode when trying to shift out of the current selected mode. The Final Drive Control Module (FDCM) must be reprogrammed with new software.

bulletin involves verifying FDCM software level and then flash reprogramming of the FDCM with new software. Customers may indicate that the ?Service 4WD? indicator in the instrument cluster is illuminated. They may also indicate that the transfer case will not shift from 4WD High, 4WD Low, and/or Neutral once the lamp is illuminated.Further investigation identifies that a Diagnostic Trouble Code C140F is stored or active in the Final Drive Control Modules (FDCM) Memory

bulletin involves verifying FDCM software level and then flash reprogramming of the FDCM with new software. Customers may indicate that the ?Service 4WD? indicator in the instrument cluster is illuminated. They may also indicate that the transfer case will not shift from 4WD High, 4WD Low, and/or Neutral once the lamp is illuminated. Further investigation identifies that a Diagnostic Trouble Code C140F is stored or active in the Final Drive Control Modules (FDCM) Memory

2005 - 2010 model year (WK) Jeep Grand Cherokee and (XK) Jeep Commander vehicles equipped with a Quadra-Drive II or Quadra-Trac II four wheel drive system. Some of the above vehicles may experience a transfer case actuator encoder electrical failure that results in unintentional transfer case shifting into or through the neutral position. NOTE: These vehicles are equipped with a NV245 transfer case that is part of the automatic four wheel drive system. The transfer case shifts into and out of four wheel drive modes and ranges automatically or based on driver inputs. Chrysler will conduct a voluntary safety recall on all affected vehicles to reprogram the Final Drive Controller Module (FDCM) with new software. The four wheel drive system will then be function tested. Vehicles found with an inoperative transfer case actuator will also have the actuator replaced. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

SELECT DOCUMENT SEARCH BUTTON BELOW. WHEN SHIFTING OUT OF CURRENT SELECTED MODE, FINAL DRIVE CONTROL MODULE (FDCM) SOFTWARE CAUSES SERVICE 4WD LIGHT TO ILLUMINATE AND SWITCHING OUT OF 4WD FAILS AND NEEDS REPROGRAMMING. MODEL 2005-2010 JEEP GRAND CHEROKEE, JEEP COMMANDER. *PE

CONVERTER LOCK AND UNLOCK WHEN IN LOCK-UP MODE. *TT

*AK

*TT

*SC

*SC

*TT

*TT

*TT

*TT

*SC

*TT

*EH

WARRANTY PLANNING & ADMINISTRATION. *TT

*TT

VARIOUS MODELS INCLUDING THE 2004 RAM TRUCK, DURANGO, SEBRING CONVERTIBLE, CHEROKEE, VISION, NEON, AND VOYAGER. *TT *SC

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

If the pins are missing request to add the dowel pin first and then install the transmission

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

If the pins are missing request to add the dowel pin first and then install the transmission

unintended change in ignition switch position while driving which may result in loss of engine power, power steering, and braking assist increasing the risk of a crash and disabling one or more of the vehicle?s safety features including the frontal airbags. Chrysler intends to repair the vehicle free of charge (parts and labor). However, the part required to provide a permanent remedy for this condition is currently not available.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

*NJ

*NJ

SOME VEHICLES MAY EXHIBIT SLIGHT IDLE FLARE AT LAUNCH. THIS MAY OCCUR DURING COLD 25 DEGREES TO 43 DEGREES TEMPERATURES AND IS MOST NOTICEABLE AFTER EXTENDED IDLING. ONCE THE TRANSMISSION WARMS, THE CONDITION WILL NO LONGER BE EXPERIENCED. *KB

ADVANCED SERVICE INFORMATION #05-002. *TT

GPOP - ISSUE REVIEW SYSTEM. *TT

*SC

*TT

*TT

*TT

*TT

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

The HFM fails to operate causing the UConnect Hands Free Communications system to not respond when system activation is attempted by the customer. Further diagnosis may reveal that when the wiTECH scan tool is used to read Diagnostic Trouble Codes (DTCs) the tool indicates that the module is not responding. Other modules on the bus may display loss of communication with the HFM. If the Hands Free Communication system is unresponsive then the HFM may require electronic reset.To perform a electronic reset, turn off the vehicle and pull the Ignition Off Drain (IOD) fuse. Wait a few minutes before reinstalling the IOD fuse and checking if the HFM is communicating. If the HFM still will not communicate, then normal No Response diagnostic should be performed. If the HFM is working properly, the module should be replaced to prevent this condition from happening again.

TO DIAGNOSTIC TROUBLE CODE P0340, P0344 OR P0116. THIS INVOLVES SELECTIVELY ERASING AND REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH NEW SOFTWARE. *PE UPDATED 5/24/10. *PE

*KB

*AK

*SC

REAR AXLE FLUID MAY CONTAMINATE THE DIFFERENTIAL MOUNTED REAR WHEEL SPEED SENSOR. *SC UPDATED 3/17/09. CSC LETTER WAS RECEIVED. *PE

*TT

TO INCLUDE 2006 CHRYSLER TOWN AND COUNTRY AND 300/TOURING. *TT

*TT

*SC

*TT

THIS CONDITION MAY BE INTERMITTENT AND COULD RESULT IN A RUN-DOWN BATTERY. CUSTOMER SATISFACTION NOTIFICATION E03. REPROGRAM FMC/FOG LAMPS. *TT

*EH

*EH

THIS BULLETIN SUPERSEDES BULLETIN 18-009-04 DATED 03/02/2004. *TT

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Please return core with original damper intact.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Please return core with original damper intact.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

*NJ

*TT

*AK

*TT

*TT

*TT

*EH

*TT

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

*TT

*TT

*TT

2004-2005 JEEP CHEROKEE AND 2005 CHRYSLER 300/MAGNUM *SC

*TT

RAPID RESPONSE TRANSMITTAL. *TT

*TT

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

WARRANTY PLANNING & ADMINISTRATION (WPA). *TT

*KB

*TT

*TT

*AK

*AK

*SC

*TT

*TT

To install, connect the electrial connector (if equipped) and snap the glass onto the mirror housing.

*KB

*TT

*NJ

*TT

*TT

*KB

*TT

*KB

OPERATOR MAY EXPERIENCE COMFORT SETTING DRIFT; COMFORT SETTING SLOW TO CHANGE WHEN ADJUSTED AND/OR COMFORT SETTING INCREMENTS TOO SMALL. *TT

*TT