2023 Jeep Grand Cherokee 4xe TSBs

have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

P0A0A-00 High Voltage System Interlock Circuit A Is Active

Flash: Power Inverter Module (PIM) Flash Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation SYMPTOM: the technician must find the following Diagnostic Trouble Code (DTC) has been set: B3A11-00 - A/C Refrigerant Expansion Valve Actuator Control Circuit Performance. Customers may experience the following: Low/weak 12V battery or a no start condition. Vehicle unable to charge while key off. This bulletin involves reprogramming the Auxiliary Hybrid Control Processor (AHCP) also known as Power Inverter Module (PIM), with the latest available software. NOTE: This new software level includes the remedy software for safety campaign 95B. If the vehicle

R1H Radio U40.20 USB Software Update - Korea Customers may experience one or more of the following: T-maps navigation feature is intermittently not available due to map loading. When the navigation speed alarm margin is set and the while driving the vehicle between the speed limit and the set margin, the navigation speed alarm will sound off continuously and the user is unable to control the volume. After setting a navigation destination and then the customer is following the navigation route, the navigation system will stop operating. Navigation touch screen menu is inoperable after setting a navigation destination. The home screen widget will be black and the navigation display map will no longer show the navigation route. WI-FI software update pop up is being triggered in non connected vehicles. Vehicle Forward Collision Warning must have two options: OFF / Warning + Active Braking. Temperature shows at upper left and right of center display highlights opposite side of what temperature hard switch is pressed. Affects Right Hand Drive RHD only. With ignition on and radio on, the radio display freezes then restarts (Rearview Camera (RVC) functions normally). Radio is taking more than one minute to start after starting the engine (RVC functions normally). System displays a blank screen in E-Hybrid tab when user switches into dark-theme mode (RVC functions normally). This bulletin involves inspecting and if required, updating the radio software level to U40.20. Depending on the radio's current software level the radio may need a one or two USB update. M08 FSAR-RSU-6722 -2-

Confirm if coolant is visibly dripping from the weeper chamber. 2.Root Cause identification The weeper chamber is designed to collect small amounts of coolant (< 3 ml/h) that pass through the dynamic seal. Red traces or shadows around the chamber may appear during initial operation due to seal adaptation or vapor condensation. These traces are not necessarily signs of a leak. Continuous dripping of coolant, however, indicates a malfunction. 3.Service Repair Procedure Lift the vehicle using an elevator. Verify if coolant is actively dripping from the weeper chamber. Run the engine at idle, alternating speed between 2000 4000 rpm for 15 minutes. Observe the weeper chamber during this test: If coolant continues to drip: Replace the water pump (possible permanent damage to the dynamic seal). If dripping stops: No further action is needed; the vehicle can be returned to the customer. 4.Clarify Leak Sources Do not confuse leaks from: The Press-In-Place rubber gasket (between water pump and engine block), or The inlet pipe nipples with leaks from the weeper chamber.

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P226D - Particulate Filter Deteriorated/Missing Substrate Bank 1. P2453 - Particulate Filter Pressure Sensor "A" Circuit Range/Performance. Customers may experience the following: Check Engine warning lamp on in the Instrument Panel Cluster (IPC) This bulletin involves inspecting and possibly rerouting the gasoline particulate sensor lines.

Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set in the Hybrid Control Processor (HCP) module: P16F0-00 - SPI Comm Hardware Fault. Customers may also comment on one or more of the following: **Low/weak 12V battery or a no start condition due to voltage being under 10.5V. Unable to charge vehicle while key is off.** Shifts rough occasionally when coming down to a stop. Shifts rough occasionally when accelerating. Shifts rough when transitioning from EV to Hybrid operation on low SoC. Shifts rough when engines starts. On part throttle accelerations with little to no battery available the transition from battery power to engine on is harsh and abrupt. The engine oil life on dashboard drops down too fast when the engine oil dilution reaches high level without the ability to recover.

follwoing DTC: - U11E3 - TCM Lost communication with ESM on D-PT CAN - U0103 - Lost communication with Electric Gear Shift Module - U0101- Lost communication with DTCM - U0418 - Implausible Data Received From Brake System Control Module - U0402 - Implausible data received from TCM **NOTE: Prior any shifter replacement Refer to TSB-21-016-25 2024-2025 WS - Valve Body Replacement. Recommended Diagnosis procedure: 1. Confirm if U0101 -Lost Communication with TCM or U0418 -Implausible Data Received From Brake System Control Module are present, if so check the Valve Body CAN Terminals any corrosion. 2. Check the wiring connectors between the ESM and the TCM and check voltage. 3. Check the pin header for the ESM for any bent pins. 4. If wiring and voltage are good and the DTCs (U11E3 - TCM Lost communication with ESM on D-PT CAN & U0103 - Lost communication with Electric Gear Shift Module) are still present, erase them with the scan tool. Reset ECU. 5. if DTCs for loss communication are still active at the ESM and you are still unable to shift then replace the Shifter module.

Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.

Gasoline Particulate Sensor Lines Incorrect Routing Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P226D - Particulate Filter Deteriorated/Missing Substrate Bank 1. P2453 - Particulate Filter Pressure Sensor "A" Circuit Range/Performance. Customers may experience the following: Check Engine warning lamp on in the Instrument Panel Cluster (IPC). This bulletin involves inspecting and possibly rerouting the gasoline particulate sensor lines.

R1H Radio U40.20 USB Software Update - Korea Customers may experience one or more of the following: **T-maps navigation feature is intermittently not available due to map loading. When the navigation speed alarm margin is set and the while driving the vehicle between the speed limit and the set margin, the navigation speed alarm will sound off continuously and the user is unable to control the volume. After setting a navigation destination and then the customer is following the navigation route, the navigation system will stop operating. Navigation touch screen menu is inoperable after setting a navigation destination. The home screen widget will be black and the navigation display map will no longer show the navigation route.** WI-FI Software update pop up is being triggered in non connected vehicles. Vehicle Forward Collision Warning must have two options: OFF/ Warning + Active Braking. Temperature shows at upper left and right of center display highlights opposite side of what temperature hard switch is pressed. Affects RHD only. With key on and radio on, The radio display freezes then restarts (Rearview Camera (RVC) functions normally). Radio is taking more than one minute to start after starting the engine (RVC functions normally). System displays a blank screen in E-Hybrid tab when user switches into dark-theme mode (RVC functions normally). This bulletin involves inspecting and if required, updating the radio software level to **U40.20**. Depending on the radio's current software level the radio may need a one or two USB update

R1H Radio U40.20 USB Software Update Customers may experience one or more of the following: **Temperature displayed in the radio display and rear HVAC are mismatched.** Wi-fi Software update pop-up is being triggered in non connected vehicles. Radio freezes and then restarts. Head Unit (HU) freezes and then restarts. HU is taking more than one minute to start after starting the engine. System displays blank screen in E-Hybrid tab when user switched to dark theme mode. Rearview Camera (RVC) functions normally. This bulletin involves inspecting and if required, updating the radio software level to **U40.20**. Depending on the radios current software level the radio may need a one or two step USB update

the vehicle must exhibit/set the following Diagnostic Trouble Code (DTC): P0B0D-00 - Electric/Auxiliary Transmission Fluid Pump Motor Control Module. Customers may also comment on the following: Vehicle is in limp mode This bulletin involves replacing the transmission oil pump.

R1H Radio U33.43 USB Software Update Customers may comment on one or more of the following: WI-FI Software update pop up is being triggered in non connected vehicles. Vehicle Forward Collision Warning must have two options: OFF/ Warning + Active Braking. Temperature shows at upper left and right of center display highlights opposite side of what temperature hard switch is pressed. Affects RHD only. With key on and radio on, The radio display freezes then restarts. Radio is taking more than one minute to start after starting the engine. System displays a blank screen in E-Hybrid tab when user switches into dark-theme mode This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radios current software level the radio may need a one or two step USB update

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): U0101 - Lost Communication With The Transmission Control Module (TCM). U0402 - Implausible Data Received From TCM. U0418 - Implausible Data Received From Brake System Control Module 1. Customers may also comment on the following: Vehicle will go in limp-in mode. After the vehicle enters limp-in mode and has been shifted into Park, the vehicle will not shift into a forward or reverse gear This bulletin involves replacing the transmission valve body assembly.

R1H Radio U33.43 USB Software Update Customers may experience one or more of the following: Wi-fi Software update pop-up is being triggered in non connected vehicles. Radio freezes and then restarts. Head Unit (HU) freezes and then restarts. HU is taking more than one minute to start after starting the engine. System displays blank screen in E-Hybrid tab when user switched to dark theme mode. This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radios current software level the radio may need a one or two step USB update.

engine idle when cold starting the engine. Low coolant level in coolant recovery bottle.

roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.

Warning Messages in the Cluster. U0131 Lost Communication with Power Steering Control Module Set.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

This bulletin involves replacing the Audio Amplifier."

Upon further investigation the technician **must** find the following Diagnostic Trouble Code (DTC) has been set: P1B0F-00 - Drive Motor A Position Sensor Offset Incorrect. Customers may also experience one or more of the following: Vehicle goes into limp home mode. Vehicle does not start. This bulletin involves inspecting the MGU serial number and possibly replacing the MGU as needed."

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0629 - Fuel Pump Control Circuit High. P0171 - Fuel system Lean. P0087 - Fuel Rail Pressure Too Low Bank 1. P16F0-00 - SPI Comm Hardware Fault. Customers may also experience one or more of the following: **Engine No Start.** The rear shafts can be damaged from pressing the accelerator while in gear with the Electronic Parking Brake (EPB) applied. Oxygen sensors can give wrong values entering EV mode. False fault detection is possible. The Instrument Panel Cluster (IPC) is unable to calculate the instantaneous fuel economy when under heavy acceleration. Variable Speed Fuel Pump doesnt operate after refuel **This bulletin involves inspecting and possibly updating the PCM with the latest available software.**"

Diagnostic Trouble Code (DTC) P1D73 And Or P05AE For Active Grill Shutter (AGS)."

the following Diagnostic Trouble Code (DTC): B3A11 - A/C Refrigerant Expansion Valve Actuator Control Circuit Performance. Customer may also comment on the following: A/C system blowing warm air. This bulletin involves replacing the battery chiller."

the following Diagnostic Trouble Code (DTC): B3A11 - A/C Refrigerant Expansion Valve Actuator Control Circuit Performance. Customer may also comment on the following: A/C system blowing warm air. This bulletin involves replacing the battery chiller."

PERFORMANCE

turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced."

Warning Messages In The Cluster. U0131 Lost Communication With Power Steering Control Module Set.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

B) FFB Program Engine, Trans, Axle Assemblies/ Prop Shafts, Exhaust, Cooling, A/C, Brakes- 2022-2024 Jeep Grand Cherokee (WL) PHEV

Grand Cherokee (WL)

Grand Cherokee (WL)

(MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0DAB-00 - Hybrid/EV Cell Balancing Performance. P0BBE-00 - Hybrid Battery Pack Voltage Variation. P1C5E-00 - Battery State Of Health Failed. P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. P0B28-00 - Hybrid/EV Battery "B" Voltage Unstable. NOTE: Any warranty qualifying issues outside of these specific DTCs will continue to be covered per the HV battery standard warranty coverage. Battery packs may contain cells with separator damage. Customers may comment on the following: Service Charging System message displayed in the Instrument Panel Cluster (IPC) and charging is inhibited. This bulletin involves replacing the high voltage battery pack.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0607-00 - ECU Internal Performance. P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. P0CA6-00 - Hybrid/EV Battery Charging Current High.** P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. P1C5E-00 - Hybrid/EV Battery State Of Health Failed. P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. P0DAB-00 - Hybrid/EV Cell Balancing Performance. P0D0F-00 - Hybrid/ EV Battery Negative Contactor A Stuck Closed. P0AA1-00 - Hybrid/EV Battery Positive Contactor A Stuck Closed. P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. Customers may also experience one or more of the following: **Vehicle does not start.** NOTE: **The no start condition is accompanied with one or more of the following DTCs: P0DAB-00, P0607-00, P0AA1-00, P0AA4-00, P0C78-00, P0CA6-00, P0B24-00, P1C5E-00 and/or P0BBE-00. P0BBE-00 and P0B28-00 will result in a MIL for 49 days. After 49 days of the MIL, the vehicle will no longer be allowed to start.** Low 12V battery causing vehicle not to start. This bulletin involves reprogramming the BPCM with the latest available software.

illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0607-00 - ECU Internal Performance. P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. P0CA6-00 - Hybrid/EV Battery Charging Current High.** P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable. P1C5E-00 - Hybrid/EV Battery State Of Health Failed. P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. P0DAB-00 - Hybrid/EV Cell Balancing Performance. P0D0F-00 - Hybrid/ EV Battery Negative Contactor A Stuck Closed. P0AA1-00 - Hybrid/EV Battery Positive Contactor A Stuck Closed. P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. Customers may also experience one or more of the following: **Vehicle does not start.** NOTE: **The no start condition is accompanied with one or more of the following DTCs: P0DAB-00, P0607-00, P0AA1-00, P0AA4-00, P0C78-00, P0CA6-00, P0B24-00, P1C5E-00 and/or P0BBE-00. P0BBE-00 and P0B28-00 will result in a MIL for 49 days. After 49 days of the MIL, the vehicle will no longer be allowed to start.** Low 12V battery causing vehicle not to start. This bulletin involves updating the BPCM with the latest available software.

Rear Power Distribution Center (PDC) Connector Pin Misaligned Customers may experience the following: SYMPTOM: Vehicle no start due to a depleted 12V battery. This bulletin involves inspecting the PDC C3 connector for improperly installed pins and correcting the connector pins if found to be installed backwards.

illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **B22A9-42 - ECU Internal Performance-general Memory Failure.** B22A9-16 - ECU Internal Performance-Circuit Voltage Below Threshold. B22A9-17 - ECU Internal Performance-Circuit Voltage Above Threshold. B22A9-19 - ECU Internal Performance-Overcurrent. B22A9-64 - ECU Internal Performance-Signal Plausibility Failure. Customers may also comment on the following: Vehicle will not charge. This bulletin involves reprogramming the IDCM with the latest available software.

Rain Sensor Internal Failure.

Rain Sensor Internal Failure.

Power Distribution Center (PDC) Connector Pin Misaligned Customers may experience the following: Vehicle no start due to a depleted 12V battery This bulletin involves inspecting the PDC C3 connector for improperly installed pins and correcting the connector pins if found to be installed backwards

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

Sensor(s) Not Reading And Or Showing Dashes.

Flash: Global Telematics Box Module (TBM) Updates The customer may experience the following: Live Traffic Updates are delayed. This bulletin involves reprogramming the TBM with the latest available software

Tire Pressure Sensors Values Are Not Displayed

Flash: Body Control Module (BCM) Updates Customers may experience one or more of the following: Battery drained. Ignition off draw. Instrument Panel Cluster (IPC) goes off and on when the vehicle goes into sleep mode. Door lock indicator lamps stay illuminated. This bulletin involves updating the BCM with the latest available software.

Ignition off draw. Instrument Panel Cluster (IPC) goes off and on when the vehicle goes into sleep mode. Door lock indicator lamps stay illuminated. This bulletin involves updating the BCM with the latest available software."

Ignition off draw. Instrument Panel Cluster (IPC) goes off and on when the vehicle goes into sleep mode. Door lock indicator lamps stay illuminated. This bulletin involves updating the BCM with the latest available software."

Order a Z part number for all Exchange Orders: Warranty, Mopar, customer pay and service contract. Order regular part number for New, Unsold units only. Please review the latest version of SOL S2208000030 regarding DVD/blue ray issues. After updating software perform resets on both display or concern may still appear. After Battery Drainage VRM do not work. Please follow the following steps. 1. Check VRM proxi, if the VRM is not aligned, perform proxi alignment, reset module. 2. If proxi is correct, reset module 3. Check for DTCs, and check wiring and components related to those DTCs and clear them."

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

swapping the old AGS for a new one, and test if the error code returns. Very often the wiring harness presents corrosion, so make sure to check it for any damage BEFORE swapping the AGS. Corrosion in the harness disrupts communication with the AGS, which sets up the DTCs for AGS performance and lights the CEL. If the AGS is inop and it will be replaced and sent back to Stellantis also send back the wiring harness with it. Make sure to fully perform the PRE-DIAGNOSTIC TROUBLESHOOTING PROCEDURE as indicated in the service library.

(MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** B22A9-64 - ECU Internal Performance-Signal Plausibility Failure. B22A9-16 - ECU Internal Performance-Circuit Voltage Below Threshold. B22A9-17 - ECU Internal Performance-Circuit Voltage Above Threshold. B22A9-19 - ECU Internal Performance-Overcurrent. Customers may also experience the following: Vehicle will not charge."

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Upon further investigation the technician must find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:** **P0B24-00 - Hybrid/EV Battery ""A"" Voltage Unstable. P1C5E-00 - Hybrid/EV Battery State Of Health Failed. P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation. P0DAB-00 - Hybrid/EV Cell Balancing Performance.** P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. P0AA1-00 - Hybrid/EV Battery Positive Contactor A Stuck Closed. Customers may also experience the following: Vehicle does not start. This bulletin involves updating the BPCM with the latest available software. "

Please follow the following steps. 1. Check ORC proxi, if the ORC is not aligned, perform proxi alignment, reset module. 2. If proxi is correct, reset module 3. Check for DTCs, and check wiring and components related to those DTCs and clear them."

After Pushed.

Driver Master Switch

chatter/streak/jump/skip/smear or make noise while traveling across the windshield.

Service Blind Spot Message In Cluster.

Service Blind Spot Message In Cluster.

observe that the interior door panel is not properly seated or attached. Panel(s) may appear warped or out of position in some areas. No signs of damage should be expected. How to diagnose: Visually inspect the door panel(s) for proper installation and check for the presence of broken or loose clips. Remove the panel and inspect clips and clip towers. Next step would be reinstalling the panel if visual inspection does not find any issues. Repair Procedure: Require a picture of the door panel(s) in the 'as found' condition so we can understand what warped means in the claims that are being created. After, check the door panel for proper installation and for the presence of broken or loose clips. Remove the panel, following normal servicing procedure, and inspect clips and clip towers. If any clips are broken or missing, replace prior to reinstalling original door. After confirmation that no loose/broken/damaged clips and/or clip towers, and reinstalling door panels does not correct issue, then a 'front door trim panel' kit / claim would be acceptable. In this case, Stellantis would like to request the panel back. How to validate fix: Verify that door has no loose/broken/damaged clips and/or clip towers. Replace any broken/missing clips where possible. Then validate that reinstalling the interior door panel addresses initial issue made within the claim.

observe that the interior door panel is not properly seated or attached. Panel(s) may appear warped or out of position in some areas. No signs of damage should be expected. How to diagnose: Visually inspect the door panel(s) for proper installation and check for the presence of broken or loose clips. Remove the panel and inspect clips and clip towers. Next step would be reinstalling the panel if visual inspection does not find any issues. Repair Procedure: Require a picture of the door panel(s) in the 'as found' condition so we can understand what warped means in the claims that are being created. After, check the door panel for proper installation and for the presence of broken or loose clips. Remove the panel, following normal servicing procedure, and inspect clips and clip towers. If any clips are broken or missing, replace prior to reinstalling original door. After confirmation that no loose/broken/damaged clips and/or clip towers, and reinstalling door panels does not correct issue, then a 'front door trim panel' kit / claim would be acceptable. In this case, Stellantis would like to request the panel back. How to validate fix: Verify that door has no loose/broken/damaged clips and/or clip towers. Replace any broken/missing clips where possible. Then validate that reinstalling the interior door panel addresses initial issue made within the claim.

Diagnostic Trouble Code (DTC) B285F-11 And Or B285F-15 Set.

Rearview Camera (RVC) Functions Normally

Flash: Instrument Panel Cluster (IPC) Updates Customers may experience the following: **The Korea language font size is larger than all other language font sizes which is causing the placeholder text used in the IPC to overlap.** After the CarPlay navigation ends, the road name details stay on the Heads Up Display (HUD) This bulletin involves reprogramming the IPC with the latest available software.

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

Blank Performance Pages (Rearview Camera (RVC) Functions Normally). Android Auto Voice Recognition (VR) inoperative. Media tuner delayed. Charge Schedule not accepting updates via phone (RVC Functions Normally). Ambient light inoperative. Map in Instrument Panel Cluster (IPC) inoperative. Media Widget blank. Navigation map black. Off-Road Pages inoperative (RVC Functions Normally). VR inoperative. Incorrect song title displayed (Carplay only). Radio display switches from Media Page to Home Page (RVC Functions Normally). Ghost touch on Navigation screen (RVC Functions Normally). Widgets missing. New User Profile does not load. Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally) This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radio's current software level the radio may need a one or two USB update

Light Displayed

R1H Radio T27.38 USB Software Update The following software enhancements are available: Virtual wall radio setting is back. Fix for difficulty playing music through QQ Music. Corrected installation error reported in the past for Macintosh App. Improvement in navigation This bulletin involves updating the R1H radio software level to T27.38.

Flash: Instrument Panel Cluster (IPC) Updates Customers may experience the following: After the CarPlay navigation ends, the road name details stay on the Heads Up Display (HUD). This bulletin involves reprogramming the IPC with the latest available software

This bulletin involves reprogramming the IPC with the latest available software."

Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only."

Blank Performance Pages (Rearview Camera (RVC) Functions Normally). Android Auto Voice Recognition (VR) inoperative. Media tuner delayed. Charge Schedule not accepting updates via phone (RVC Functions Normally). Ambient light inoperative. Map in Instrument Panel Cluster (IPC) inoperative. Media Widget blank. Navigation map black. Off-Road Pages inoperative (RVC Functions Normally). VR inoperative. Incorrect song title displayed (Carplay only). Radio display switches from Media Page to Home Page (RVC Functions Normally). Ghost touch on Navigation screen (RVC Functions Normally). Widgets missing. New User Profile does not load. Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally). REPAIR SUMMARY: This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radios current software level the radio may need a one or two USB update."

Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process

Please ensure to order the correct CADM and Long Range Camera Part Number(s) the vehicle was built with. The Root of the Original and Replacement part should be identical, the difference will be in the NIK level. Technician Removal of the Long Range Camera and CADM for Testing Purposes: Please ensure the root of the Original and Replacement part are identical.

Adding Remote Start

B1552-2A Code Set.

driving.

and bearing area during turns while driving.

and Service Electric Power Steering Messages.

Tie Rod And Or Electric Power Steering (EPS) Units.

and Service Electric Power Steering Messages.

Customer Complaint/Technician Observation: Customer may state the vehicle drives straight but the steering wheel is off center. They may also describe the condition as a pull or a lead due to them trying to keep the steering wheel centered. Discussion: Drive on both highway and city roads if possible. If equipped with air suspension, place the vehicle in normal ride height (NRH). Refer to Service Library 02 - Front Suspension / Wheel Alignment / Diagnosis and Testing for a list of conditions, possible causes and corrections.

Customer Complaint/Technician Observation: Customer may state the vehicle drives straight but the steering wheel is off center. They may also describe the condition as a pull or a lead due to them trying to keep the steering wheel centered. Discussion: Drive on both highway and city roads if possible. If equipped with air suspension, place the vehicle in normal ride height (NRH). Refer to Service Library 02 - Front Suspension / Wheel Alignment / Diagnosis and Testing for a list of conditions, possible causes and corrections.

Lack Of Precise Steering.

Shifter.

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.

used as the reason for unit replacement. Visible ""glitter"" or debris in the pan does not justify complete unit replacements."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."

transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

Diagnostic Trouble Code (DTC) C1477-98 Transfer Case Clutch Component Or System Over Temperature, Set.

Noise is not heard when the front axle is disengaged. (The noise can happen more as the ambient temperatures become colder). This bulletin involves reprogramming the DTCM with the latest software available."

A Fast Feedback Program - Auto 8P75PH PHEV Transmission, HV Battery Assembly and HV System Components - 2022 - 2024 Jeep Grand Cherokee (WL) PHEV

Components - 2022 - 2024 Jeep Grand Cherokee (WL) PHEV (Rev. C)"

layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

C14A1-74 DTC will be present (Active or Stored).

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

TPM Lamp On.

layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

Diagnostic Trouble Codes (DTCs) B166E-13 B17AD-13 May Be Set.

assemblies are fogged with a light layer of condensation on the inside of the lenses. "

Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order "68" part number for New unsold units only.

and/or C1463-92 Front Axle Disconnect-Performance or Incorrect Operation, Set."

Investigate the disconnecting stabilizer bar for a broken or cacked weld on the upper mount (anti rotation bracket). Instead of the replacing the whole stabilizer bar use Kit #PN#68730602AB. Refer to SOL #S22502000002 for additional information

"

Root cause was identified as anti-rotation bracket (connects the actuator to the stabar) coming loose due to inadequate clamp load at the joint and weld (holds the bolt shaft and bracket flange) was poorly designed. If any vehicle causes BSR because of this Bracket failure (loose joint/ bracket bends) DO NOT replace whole stabar assembly, instead replace with the service kit (PN#68730602AA). Dealer must need to order the parts from part ordering system for this claim. This kit contains 1 bracket (PN 68730603AA), 3 M10 Nut (PN 68730605AA), 2 M8X1.5 Bolt (PN 68730606AA) and 2 M10X1.5 bolt (PN 06513427AA). 1 M10 Bolt (PN 68730607AA). This kit will also contain a new torque instruction for the bolt which holds the clamp bracket to this failed anti-rotation bracket. DO NOT apply the old torque (45+/5Nm Direct torque). The new torque is Angle controlled torque monitor (20Nm Snug torque, 110 deg Angle, monitor torque within 40-70Nm). Please use Service Library for your reference."

Root cause was identified as anti-rotation bracket (connects the actuator to the stabar) coming loose due to inadequate clamp load at the joint and weld (holds the bolt shaft and bracket flange) was poorly designed. If any vehicle causes BSR because of this Bracket failure (loose joint/ bracket bends) DO NOT replace whole stabar assembly, instead replace with the service kit (PN#68730602AA). Dealer must need to order the parts from part ordering system for this claim. This kit contains 1 bracket (PN 68730603AA), 3 M10 Nut (PN 68730605AA), 2 M8X1.5 Bolt (PN 68730606AA) and 2 M10X1.5 bolt (PN 06513427AA). 1 M10 Bolt (PN 68730607AA). This kit will also contain a new torque instruction for the bolt which holds the clamp bracket to this failed anti-rotation bracket. DO NOT apply the old torque (45+/5Nm Direct torque). The new torque is Angle controlled torque monitor (20Nm Snug torque, 110 deg Angle, monitor torque within 40-70Nm). Please use Service Library for your reference."

Vehicle sets wheel speed BSCM/ABS fault codes.

traveling at less than 5 kph (3 mph) and the brake pedal is pressed, then both turn lights will flash for two milliseconds. If the vehicle is traveling at less than 5 kph (3 mph) and one turn light is activated, then the opposite turn light will flash for 20 milliseconds. NOTE: This issue only effects the trailer lighting This bulletin involves updating the TTM with the latest available software."

Unavailable or Service Rear Braking Assist System" with Performance Diagnostic Trouble Codes (DTCs)

traveling at less than 5 kph (3 mph) and the brake pedal is pressed, then both turn lights will flash for two milliseconds. If the vehicle is traveling at less than 5 kph (3 mph) and one turn light is activated, then the opposite turn light will flash for 20 milliseconds This bulletin involves updating the TTM with the latest available software."

Radio USB Update to U40.20 Customers may experience one or more of the following: Temperature displayed in the radio display screen and rear HVAC are mismatched. Auto door locks are inoperable. This bulletin involves inspecting and if required, updating the radio software level to U40.20. Depending on the radios current software level the radio may need a one or two USB update.

Radio USB Update to U40.20 Customers may experience one or more of the following: Temperature displayed in the radio display screen and rear HVAC are mismatched. Auto door locks are inoperable This bulletin involves inspecting and if required, updating the radio software level to U40.20. Depending on the radios current software level the radio may need a one or two USB update.