2021 Jeep Grand Cherokee 4XE TSBs

Mirror Contacts Door Window Glass In The Folded Position.

Mirror Contacts Door Window Glass In The Folded Position.

Mirror Contacts Door Window Glass In The Folded Position.

Mirror Contacts Door Window Glass In The Folded Position.

After Pushed.

Service Blind Spot Message In Cluster.

Service Blind Spot Message In Cluster.

observe that the interior door panel is not properly seated or attached. Panel(s) may appear warped or out of position in some areas. No signs of damage should be expected. How to diagnose: Visually inspect the door panel(s) for proper installation and check for the presence of broken or loose clips. Remove the panel and inspect clips and clip towers. Next step would be reinstalling the panel if visual inspection does not find any issues. Repair Procedure: Require a picture of the door panel(s) in the 'as found' condition so we can understand what warped means in the claims that are being created. After, check the door panel for proper installation and for the presence of broken or loose clips. Remove the panel, following normal servicing procedure, and inspect clips and clip towers. If any clips are broken or missing, replace prior to reinstalling original door. After confirmation that no loose/broken/damaged clips and/or clip towers, and reinstalling door panels does not correct issue, then a 'front door trim panel' kit / claim would be acceptable. In this case, Stellantis would like to request the panel back. How to validate fix: Verify that door has no loose/broken/damaged clips and/or clip towers. Replace any broken/missing clips where possible. Then validate that reinstalling the interior door panel addresses initial issue made within the claim.

observe that the interior door panel is not properly seated or attached. Panel(s) may appear warped or out of position in some areas. No signs of damage should be expected. How to diagnose: Visually inspect the door panel(s) for proper installation and check for the presence of broken or loose clips. Remove the panel and inspect clips and clip towers. Next step would be reinstalling the panel if visual inspection does not find any issues. Repair Procedure: Require a picture of the door panel(s) in the 'as found' condition so we can understand what warped means in the claims that are being created. After, check the door panel for proper installation and for the presence of broken or loose clips. Remove the panel, following normal servicing procedure, and inspect clips and clip towers. If any clips are broken or missing, replace prior to reinstalling original door. After confirmation that no loose/broken/damaged clips and/or clip towers, and reinstalling door panels does not correct issue, then a 'front door trim panel' kit / claim would be acceptable. In this case, Stellantis would like to request the panel back. How to validate fix: Verify that door has no loose/broken/damaged clips and/or clip towers. Replace any broken/missing clips where possible. Then validate that reinstalling the interior door panel addresses initial issue made within the claim.

Diagnostic Trouble Code (DTC) B285F-11 And Or B285F-15 Set.

returning to position, heated steering wheel not working and/or steering controls inop, Electronic Stability Control (ESC) light on, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced. Note: WL / WS SCCMs do not contain a Steering Angle Sensor (SAS) The Steering Angle is computed within the Electronic Power Steering (EPS) module. See Electronic Power Steering (EPS) module for diagnosis and repair procedures.

and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: **Oil Level High Warning in the Instrument Panel Cluster (IPC).** Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. Vehicle is not heating up fast enough at freezi

845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

R1H Radio U40.20 USB Software Update - Korea Customers may experience one or more of the following: T-maps navigation feature is intermittently not available due to map loading. When the navigation speed alarm margin is set and the while driving the vehicle between the speed limit and the set margin, the navigation speed alarm will sound off continuously and the user is unable to control the volume. After setting a navigation destination and then the customer is following the navigation route, the navigation system will stop operating. Navigation touch screen menu is inoperable after setting a navigation destination. The home screen widget will be black and the navigation display map will no longer show the navigation route. WI-FI software update pop up is being triggered in non connected vehicles. Vehicle Forward Collision Warning must have two options: OFF / Warning + Active Braking. Temperature shows at upper left and right of center display highlights opposite side of what temperature hard switch is pressed. Affects Right Hand Drive RHD only. With ignition on and radio on, the radio display freezes then restarts (Rearview Camera (RVC) functions normally). Radio is taking more than one minute to start after starting the engine (RVC functions normally). System displays a blank screen in E-Hybrid tab when user switches into dark-theme mode (RVC functions normally). This bulletin involves inspecting and if required, updating the radio software level to U40.20. Depending on the radio's current software level the radio may need a one or two USB update. M08 FSAR-RSU-6722 -2-

R1H Radio U40.20 USB Software Update - Korea Customers may experience one or more of the following: **T-maps navigation feature is intermittently not available due to map loading. When the navigation speed alarm margin is set and the while driving the vehicle between the speed limit and the set margin, the navigation speed alarm will sound off continuously and the user is unable to control the volume. After setting a navigation destination and then the customer is following the navigation route, the navigation system will stop operating. Navigation touch screen menu is inoperable after setting a navigation destination. The home screen widget will be black and the navigation display map will no longer show the navigation route.** WI-FI Software update pop up is being triggered in non connected vehicles. Vehicle Forward Collision Warning must have two options: OFF/ Warning + Active Braking. Temperature shows at upper left and right of center display highlights opposite side of what temperature hard switch is pressed. Affects RHD only. With key on and radio on, The radio display freezes then restarts (Rearview Camera (RVC) functions normally). Radio is taking more than one minute to start after starting the engine (RVC functions normally). System displays a blank screen in E-Hybrid tab when user switches into dark-theme mode (RVC functions normally). This bulletin involves inspecting and if required, updating the radio software level to **U40.20**. Depending on the radio's current software level the radio may need a one or two USB update

R1H Radio U40.20 USB Software Update Customers may experience one or more of the following: **Temperature displayed in the radio display and rear HVAC are mismatched.** Wi-fi Software update pop-up is being triggered in non connected vehicles. Radio freezes and then restarts. Head Unit (HU) freezes and then restarts. HU is taking more than one minute to start after starting the engine. System displays blank screen in E-Hybrid tab when user switched to dark theme mode. Rearview Camera (RVC) functions normally. This bulletin involves inspecting and if required, updating the radio software level to **U40.20**. Depending on the radios current software level the radio may need a one or two step USB update

R1H Radio U33.43 USB Software Update Customers may comment on one or more of the following: WI-FI Software update pop up is being triggered in non connected vehicles. Vehicle Forward Collision Warning must have two options: OFF/ Warning + Active Braking. Temperature shows at upper left and right of center display highlights opposite side of what temperature hard switch is pressed. Affects RHD only. With key on and radio on, The radio display freezes then restarts. Radio is taking more than one minute to start after starting the engine. System displays a blank screen in E-Hybrid tab when user switches into dark-theme mode This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radios current software level the radio may need a one or two step USB update

R1H Radio U33.43 USB Software Update Customers may experience one or more of the following: Wi-fi Software update pop-up is being triggered in non connected vehicles. Radio freezes and then restarts. Head Unit (HU) freezes and then restarts. HU is taking more than one minute to start after starting the engine. System displays blank screen in E-Hybrid tab when user switched to dark theme mode. This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radios current software level the radio may need a one or two step USB update.

engine idle when cold starting the engine. Low coolant level in coolant recovery bottle.

Warning Messages in the Cluster. U0131 Lost Communication with Power Steering Control Module Set.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

This bulletin involves replacing the Audio Amplifier."

Diagnostic Trouble Code (DTC) P1D73 And Or P05AE For Active Grill Shutter (AGS)."

turning off, wipers not returning to position, heated steering wheel not working and/or steering controls inop, please follow these steps: 1.- Review if there is any active DTC. Refer to service library procedure and follow diagnosis steps. 2.- If failure still present, make sure all the switches', horn's, heated steering wheel, airbag's harness are properly connected and there is no corrosion or pinching, disconnect the switches & reconnect them, and reverify the issue. 3.- Verify if failure is still present, review if there is lack of communication between SCCM and BCM. For example, activate turn signals or wipers. 4.- Read at the BCM diagnosis session if BCM is receiving information from SCCM. Through diagnosis review if activation from horn, wipers or turn signal is requested and are working. 5.- Disconnect the SCCM fuse for around 30s,and repeat the previous steps to see if failure still present. 6.- Do a hard reset to BCM and evaluate if any DTC is set. Retest if failure still present. Review the active DTCs. 7.- Before replacing the SCCM disconnect it and reconnect it again. Note: Wipers position is not controlled by SCCM, verify motor wiper status if issue continues. If request from SCCM is sent to BCM, then verify if the communication to wipers is not working properly. If there are no DTC's active, physical defects, steering controls inop, wipers inop, heated steering wheel inop, then SCCM does not need to be replaced."

Warning Messages In The Cluster. U0131 Lost Communication With Power Steering Control Module Set.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

Inaccurate status or information displayed during phone calls- Voice Recognition performance- Carplay connectivity issues- Black / blank screens for Navigation or Media apps not affecting rearview camera funtionality- Visual glitch on Front passenger Display- Unresponsive widgets- Light & Dark mode discrepancy between screen views- Unresponsive hard button to turn screen off- Incomplete or innacurate pop-up notifications- Radio stuck in Valet Mode- Phantom / Ghost touch on Media screens- Incorrect menu displayed

Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed.

Blank Performance Pages (Rearview Camera (RVC) Functions Normally). Android Auto Voice Recognition (VR) inoperative. Media tuner delayed. Charge Schedule not accepting updates via phone (RVC Functions Normally). Ambient light inoperative. Map in Instrument Panel Cluster (IPC) inoperative. Media Widget blank. Navigation map black. Off-Road Pages inoperative (RVC Functions Normally). VR inoperative. Incorrect song title displayed (Carplay only). Radio display switches from Media Page to Home Page (RVC Functions Normally). Ghost touch on Navigation screen (RVC Functions Normally). Widgets missing. New User Profile does not load. Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally) This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radio's current software level the radio may need a one or two USB update

Blank Performance Pages (Rearview Camera (RVC) Functions Normally). Android Auto Voice Recognition (VR) inoperative. Media tuner delayed. Charge Schedule not accepting updates via phone (RVC Functions Normally). Ambient light inoperative. Map in Instrument Panel Cluster (IPC) inoperative. Media Widget blank. Navigation map black. Off-Road Pages inoperative (RVC Functions Normally). VR inoperative. Incorrect song title displayed (Carplay only). Radio display switches from Media Page to Home Page (RVC Functions Normally). Ghost touch on Navigation screen (RVC Functions Normally). Widgets missing. New User Profile does not load. Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally). REPAIR SUMMARY: This bulletin involves inspecting and if required, updating the radio software level to U33.43. Depending on the radios current software level the radio may need a one or two USB update."

Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process

B1552-2A Code Set.

Battery or Open Before replacing DDM/PDM. Inspect connection on Mirror connector end. Perform electrical continuity test. After succesful continuity test. Via Witech perform hard reset and clear DTC.

Required Is Set

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

components need to be replaced as a pair.

Sensor(s) Not Reading And Or Showing Dashes.

Tire Pressure Sensors Values Are Not Displayed

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

swapping the old AGS for a new one, and test if the error code returns. Very often the wiring harness presents corrosion, so make sure to check it for any damage BEFORE swapping the AGS. Corrosion in the harness disrupts communication with the AGS, which sets up the DTCs for AGS performance and lights the CEL. If the AGS is inop and it will be replaced and sent back to Stellantis also send back the wiring harness with it. Make sure to fully perform the PRE-DIAGNOSTIC TROUBLESHOOTING PROCEDURE as indicated in the service library.

During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.

During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.

During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.

During diagnosis dealers may find rubber separating from the bushing on the tension link. This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.

Power surge on USB hub detected Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.

Power surge on USB hub detected Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle

Power surge on USB hub detected Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle

B1A17-00 in The Radio Frequency Hub (RFH)

"

Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only.

AM level is not available to order at this time. AJ or AK level is recommended to verify proper connected services at this time.

Order a "Z" part number for all Exchange Orders, Warranty, Mopar, Customer Pay and Service Contract. Order "68" part number for New, Unsold units only.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order "68" part number for New unsold units only.

and/or C1463-92 Front Axle Disconnect-Performance or Incorrect Operation, Set."

driving.

and bearing area during turns while driving.

and Service Electric Power Steering Messages.

Tie Rod And Or Electric Power Steering (EPS) Units.

and Service Electric Power Steering Messages.

Customer Complaint/Technician Observation: Customer may state the vehicle drives straight but the steering wheel is off center. They may also describe the condition as a pull or a lead due to them trying to keep the steering wheel centered. Discussion: Drive on both highway and city roads if possible. If equipped with air suspension, place the vehicle in normal ride height (NRH). Refer to Service Library 02 - Front Suspension / Wheel Alignment / Diagnosis and Testing for a list of conditions, possible causes and corrections.

Customer Complaint/Technician Observation: Customer may state the vehicle drives straight but the steering wheel is off center. They may also describe the condition as a pull or a lead due to them trying to keep the steering wheel centered. Discussion: Drive on both highway and city roads if possible. If equipped with air suspension, place the vehicle in normal ride height (NRH). Refer to Service Library 02 - Front Suspension / Wheel Alignment / Diagnosis and Testing for a list of conditions, possible causes and corrections.

Lack Of Precise Steering.

layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

C14A1-74 DTC will be present (Active or Stored).

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

TPM Lamp On.

layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.

Diagnostic Trouble Codes (DTCs) B166E-13 B17AD-13 May Be Set.

assemblies are fogged with a light layer of condensation on the inside of the lenses. "

Blank screen and then reboot every 2 minutes and 40 seconds. (Rearview Camera Functions Normally). Paddle shifters not working/no longer a setting. Autolocks not working. Auto headlights not working. AM station not working (Appears some of the vehicles PROXI defaults to "1" which is absent for AM). Album Art flickering issue. Blank screen and then reboot every 2 minutes and 40 seconds. CarPlay icon disappears from main screen while still active, leaving no navigation path back. Light/dark theme mismatch between Radio and temperature screens at key-on Radio experiences lockups, resets, blank screens, and language issues after FOTA. Valet mode sends duplicate requests causing HU and vehicle state misalignment. Rear seat media page intermittently shows a blank screen. Unable to select or drag 'Pitch and Roll' widget on home screen. USB playback resumes incorrectly, skipping to next track after reconnect. Album art not displayed on HMI despite availability in media. Incorrect call timer displayed for conference calls. Call status remains 'active' on widget after call ends. Second call status not updated on home screen widget. Rear entertainment tab intermittently blank when switching apps. System crashes for 20 to 30 seconds after voice reply action. Media progress bar continues incorrectly after second call acceptance. CarPlay device fails to reconnect automatically or manually. Rear HVAC lock/unlock text missing while icon is present. Visual glitch observed on Front Passenger Display Module (FPDM) display. Surround view camera accessible while driving across apps (unexpected behavior). IPC navigation map fails to load despite radio showing navigation. Head Up Display (HUD) layout resets after overnight sleep cycle. ParkSense triggers unintended surround camera activation. HUD settings not retained after ignition cycle. Audio focus stuck on VR; selected message not read. Preset bar appears blank after overnight sleep cycle. FM channel switches unexpectedly and reverts after delay. Massage activation causes HU black screen/media disruption. Non-applicable ambient lighting setting visible in vehicle menu. Navigation screen appears black after system startup. Track name flickers on status bar during CarPlay playback. HU toggles between Home and Media screens without user input. Phantom touch causes navigation to switch from full screen to split view. HU redirects to CarPlay tab when exiting camera unexpectedly. Unable to select the Turn by Turn Navigation. Blank Performance Pages (Rearview Camera Functions Normally). Android Auto Voice Recognition (VR) inoperative. Media tuner delayed. Charge Schedule not accepting updates via phone (Rearview Camera Functions Normally). Ambient light inoperative. Map in Instrument Panel Cluster (IPC) inoperative. Media Widget blank. Navigation map black. Off-Road Pages inoperative (Rearview Camera Functions Normally). VR inoperative. Incorrect song title displayed (Carplay only). Radio display switches from Media Page to Home Page (Rearview Camera Functions Normally). Ghost touch on Navigation screen (Rearview Camera Functions Normally). Widgets missing. New User Profile does not load. Returns to wrong page after view camera event selected by customer in the Camera View Pages (Rearview Camera Functions Normally). This bulletin involves inspecting and if required, updating the radio software level to U41.10. Depending on the radio's current software level the radio may need a one or two USB update.

Blank screen and then reboot every 2 minutes and 40 seconds. (Rearview Camera (RVC) Functions Normally). Paddle shifters not working/No longer a setting. Autolocks not working. Auto headlights not working. AM station not working (Appears some of the vehicles PROXI defaults to "1" which is absent for AM). Album Art flickering issue. Blank screen and then reboot every 2 minutes and 40 seconds. CarPlay icon disappears from main screen while still active, leaving no navigation path back. Light/dark theme mismatch between Radio and temperature screens at key-on Radio experiences lockups, resets, blank screens, and language issues after FOTA. Valet mode sends duplicate requests causing HU and vehicle state misalignment. Rear seat media page intermittently shows a blank screen. Unable to select or drag 'Pitch and Roll' widget on home screen. USB playback resumes incorrectly, skipping to next track after reconnect. Album art not displayed on HMI despite availability in media. Incorrect call timer displayed for conference calls. Call status remains 'active' on widget after call ends. Second call status not updated on home screen widget. Rear entertainment tab intermittently blank when switching apps. System crashes for 20 to 30 seconds after voice reply action. Media progress bar continues incorrectly after second call acceptance. CarPlay device fails to reconnect automatically or manually. Rear HVAC lock/unlock text missing while icon is present. Visual glitch observed on FPDM display. Surround view camera accessible while driving across apps (unexpected behavior). IPC navigation map fails to load despite HU showing navigation. HUD layout resets after overnight sleep cycle. ParkSense triggers unintended surround camera activation. HUD settings not retained after ignition cycle. Audio focus stuck on VR; selected message not read. Preset bar appears blank after overnight sleep cycle. FM channel switches unexpectedly and reverts after delay. Massage activation causes HU black screen/media disruption. Non-applicable ambient lighting setting visible in vehicle menu. Navigation screen appears black after system startup. Track name flickers on status bar during CarPlay playback. HU toggles between Home and Media screens without user input. Phantom touch causes navigation to switch from full screen to split view. HU redirects to CarPlay tab when exiting camera unexpectedly.** Unable to select the Turn by Turn Navigation. Blank Performance Pages (Rearview Camera (RVC) Functions Normally). Android Auto Voice Recognition (VR) inoperative. Media tuner delayed. Charge Schedule not accepting updates via phone (RVC Functions Normally). Ambient light inoperative. Map in Instrument Panel Cluster (IPC) inoperative. Media Widget blank. Navigation map black. Off-Road Pages inoperative (RVC Functions Normally). VR inoperative. Incorrect song title displayed (Carplay only). Radio display switches from Media Page to Home Page (RVC Functions Normally). Ghost touch on Navigation screen (RVC Functions Normally). Widgets missing. New User Profile does not load. Returns to wrong page after View Camera Event selected by customer in the Camera View Pages (RVC Functions Normally) This bulletin involves inspecting and if required, updating the radio software level to **U41.10.** Depending on the radio's current software level the radio may need a one or two USB update.

Shifter.

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.

used as the reason for unit replacement. Visible ""glitter"" or debris in the pan does not justify complete unit replacements."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."

transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

output, the front center console's surfaces, first row and second row cup holders and storage bins are getting warm to the touch. This bulletin involves removing the front center console and installing an insulator foam pad on top of the Center Console air duct.

Vehicle sets wheel speed BSCM/ABS fault codes.

traveling at less than 5 kph (3 mph) and the brake pedal is pressed, then both turn lights will flash for two milliseconds. If the vehicle is traveling at less than 5 kph (3 mph) and one turn light is activated, then the opposite turn light will flash for 20 milliseconds. NOTE: This issue only effects the trailer lighting This bulletin involves updating the TTM with the latest available software."

traveling at less than 5 kph (3 mph) and the brake pedal is pressed, then both turn lights will flash for two milliseconds. If the vehicle is traveling at less than 5 kph (3 mph) and one turn light is activated, then the opposite turn light will flash for 20 milliseconds This bulletin involves updating the TTM with the latest available software."

Radio USB Update to U40.20 Customers may experience one or more of the following: Temperature displayed in the radio display screen and rear HVAC are mismatched. Auto door locks are inoperable. This bulletin involves inspecting and if required, updating the radio software level to U40.20. Depending on the radios current software level the radio may need a one or two USB update.

Diagnostic Trouble Code (DTC) B1D9B-54- Seat Horizontal Front Stop Not Learned-Missing Calibration