2020 Jeep Gladiator TSBs

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Bluetooth Speaker Does Not Charge

DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE

Tire Pressure Sensors Values Are Not Displayed

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

notification on customers mobile application."

for any physical issue (Button stuck, broke). If not, physical issue is found move to next step 2.- Make sure all the switches harness are properly connected, disconnect the switch and reconnect it, and reverify the issue. If after performing these steps the switch remains faulty, please replace the switch

U0131 Lost Communication With Electro Hydraulic Power Steering Control Module (EHPS)."

The parts kit (SENSOR KIT, Axle: 68544629A$) must be used to repair the Axle Locker Sensor on JL/JT equipped with the M210 and M220 Tru-Lok axles (DSE). Internal axle components are serviceable. Complete axle assemblies should not be replaced unless necessary due to damaged housing. Over repairs may be subject to chargeback."

Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: ? C1451-11 - Service Axle Locker System** Customers may also comment on a Service Axle Locker message displayed in the Electronic Vehicle Information Center (EVIC) for this condition.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Service Electric Power Steering Message On Cluster.

please contact FCA redacted content. If no response in 15 minutes, proceed with repair.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

The customer may notice one or more of the following:Intermittent change of smell or humidity level in vehicle. An intermittent blast of warm air when A/C is on. Intermittent increase of outside air through the HVAC system. In addition, the following software enhancement is also available:Improvements for customer concerns of 'cabin too warm', specifically in the mid ambient temperature range 4.5-15.5 C (40-60 F).

Assistance System Module) Does Not Calibrate

Upon further inspection, there is a Diagnostic Trouble Code (DTC) P0128 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) set in the PCM.

equipped with the M210 and M220 Tru-Lok axles (DSE). This parts kit must be used when only the Axle Locker Sensor fails. Do not replace the axle for sensor failure.

EPS Light On.

equipped with the M210 and M220 Tru-Lok axles (DSE). This parts kit must be used when only the Axle Locker Sensor fails. Do not replace the axle for sensor failure.

equipped with the M210 and M220 Tru-Lok axles (DSE). This parts kit must be used when only the Axle Locker Sensor fails. Do not replace the axle for sensor failure.

fuel tank and O-ringdue to a P0461 Diagnostic Trouble Code (DTC). Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the followingDiagnostic Trouble Code (DTC) has been set:P0461 - Fuel Level Sensor 1 Performance. In addition, the customer may notice one or more of the following:The fuel gauge is not accurate. The fuel gauge is stuck.

Tire Pressure Sensors Values Are Not Displayed

The customer may notice one or more of the following:Intermittent change of smell or humidity level in vehicle. An intermittent blast of warm air when A/C is on. Intermittent increase of outside air through the HVAC system. In addition, the following software enhancement is also available:Improvements for customer concerns of 'cabin too warm', specifically in the mid ambient temperature range 4.5-15.5 C (40-60 F).

Assistance System Module) Does Not Calibrate

Upon further inspection, there is a Diagnostic Trouble Code (DTC) P0128 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) set in the PCM.

The customer may notice one or more of the following:Intermittent change of smell or humidity level in vehicle. An intermittent blast of warm air when A/C is on. Intermittent increase of outside air through the HVAC system. In addition, the following software enhancement is also available:Improvements for customer concerns of 'cabin too warm', specifically in the mid ambient temperature range 4.5-15.5 C (40-60 F).

Assistance System Module) Does Not Calibrate

Upon further inspection, there is a Diagnostic Trouble Code (DTC) P0128 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) set in the PCM.

2018 - 2022 JL/JT equipped with the M210 and M220 Tru-Lok axles (DSE). This new parts kit must be used when only the Axle Locker Sensor fails.

replacing this part, please perform the following checks: - Check speaker on/off function. Press and HOLD power button for at least 4 seconds. If speaker powers up you will hear the "wake up" sound. Confer with customer to see if issue is resolved. - If speaker does not power up, this may be due to a low/dead internal battery. This could be due to improper docking/charging within dock located in rear compartment of vehicle. Check for dent/damage on back of speaker (sign of improper docking). Install speaker into docking station - turn up radio and ensure audio is passing through the speaker (this confirms that the dock is plugged into vehicle harness). When docked, the speaker is quieter than the other speakers so you will need to get close to hear the radio sounds coming out of the wireless speaker in the dock. (It takes a few seconds after docking for the speaker to come on) Speaker needs to be in dock for at least 20 minutes with vehicle ON to bring internal battery up to charge. Once this is done, check again for on/off function - If speaker still does not power up after proper charging, speaker can be replaced under warranty. ***please reference the wireless speaker owner's manual for further details***

Upon further investigation, one or more of the following fault codes may be set in the PCM:

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

After update, system requires three sleep cycles to function properly. Please verify camera LVDS- Low-Voltage Differential Signaling cable connection at camera and radio head unit. Also verify harness connection between high mounted stop lamp and body harness for bent pins or loose connection at XY310A, XY485A inlines. Please create and send a copy of the vehicle scan report and specify radio SW version and radio head unit ID toFCA Redacted Content or call FCA Redacted Content for any additional questions or assistance needed. If no response in 15 minutes, proceed with repair. Please be sure to attach a copy of the Vehicle Scan Report on the repair order.

EPS Light On.

sales code is present to restore rear defrost function. The switch is not provided in this kit and a service replacement part must be ordered. See service information procedure for switch replacement and below chart for replacement part numbers. vehicle has GTP+BNH+HAA replace HVAC control with pn 6BE36TRMAC vehicle has GTP+BNH-HAA replace HVAC control with pn 6BE37TRMAC vehicle has GTP+HAA-BNH replace HVAC control with pn 6BE40TRMAC vehicle has GTP-HAA-BNH replace HVAC control with pn 6BE41TRMAC Please ensure that the proper color code is used in place of the part TRM designation. For any questions call John Altsman at (248) 512-9361.

following: http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE If a connector repair kit is not available on the website contact FCA Redacted Content to see if an alternative repair kit is available for your application prior to ordering the harness. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Upon further investigation, one or more of the following fault codes may be set in the PCM:

The customer may notice one or more of the following:Intermittent change of smell or humidity level in vehicle. An intermittent blast of warm air when A/C is on. Intermittent increase of outside air through the HVAC system. In addition, the following software enhancement is also available:Improvements for customer concerns of 'cabin too warm', specifically in the mid ambient temperature range 4.5-15.5 C (40-60 F).

Assistance System Module) Does Not Calibrate

Upon further inspection, there is a Diagnostic Trouble Code (DTC) P0128 Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) set in the PCM.

After update, system requires three sleep cycles to function properly. Please verify camera LVDS- Low-Voltage Differential Signaling cable connection at camera and radio head unit. Also verify harness connection between high mounted stop lamp and body harness for bent pins or loose connection at XY310A, XY485A inlines. Please create and send a copy of the vehicle scan report and specify radio SW version and radio head unit ID toFCA Redacted Content or call FCA Redacted Content for any additional questions or assistance needed. If no response in 15 minutes, proceed with repair. Please be sure to attach a copy of the Vehicle Scan Report on the repair order.

EPS Light On.

fuel tank and O-ringdue to a P0461 Diagnostic Trouble Code (DTC). Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P0461 - Fuel Level Sensor 1 Performance. In addition, the customer may notice one or more of the following:The fuel gauge is not accurate. The fuel gauge is stuck.

replacing this part, please perform the following checks: - Check speaker on/off function. Press and HOLD power button for at least 4 seconds. If speaker powers up you will hear the "wake up" sound. Confer with customer to see if issue is resolved. - If speaker does not power up, this may be due to a low/dead internal battery. This could be due to improper docking/charging within dock located in rear compartment of vehicle. Check for dent/damage on back of speaker (sign of improper docking). Install speaker into docking station - turn up radio and ensure audio is passing through the speaker (this confirms that the dock is plugged into vehicle harness). When docked, the speaker is quieter than the other speakers so you will need to get close to hear the radio sounds coming out of the wireless speaker in the dock. (It takes a few seconds after docking for the speaker to come on) Speaker needs to be in dock for at least 20 minutes with vehicle ON to bring internal battery up to charge. Once this is done, check again for on/off function - If speaker still does not power up after proper charging, speaker can be replaced under warranty. ***please reference the wireless speaker owner's manual for further details***

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Customers may notice the following condition:Two zoom buttonsFig.1appear on the Rear View Camera (RVC) screen.

Technician observes DTC P0456 EVAP System Small Leak or P0455 EVAP System Large Leak detected set in PCM.

Customer does not have Selectable Tire Fill Alert due to a late feature availability.Selectable Tire Fill Alert (STFA) Function: (https://www.youtube.com/watch?v=znqYo86deCg)

involves reconfiguring the BCM to enable the STFA settings.This re-configuration will enable the STFA (sales code LA5). Customer does not have Selectable Tire Fill Alert due to a late feature availability.Selectable Tire Fill Alert (STFA) Function: (https://www.youtube.com/watch?v=znqYo86deCg)

Customer does not have Selectable Tire Fill Alert due to a late feature availability.Selectable Tire Fill Alert (STFA) Function: (https://www.youtube.com/watch?v=znqYo86deCg)

involves reconfiguring the BCM to enable the STFA settings.This re-configuration will enable the STFA (sales code LA5). Customer does not have Selectable Tire Fill Alert due to a late feature availability.Selectable Tire Fill Alert (STFA) Function: (https://www.youtube.com/watch?v=znqYo86deCg)

Customer does not have Selectable Tire Fill Alert due to a late feature availability.Selectable Tire Fill Alert (STFA) Function: (https://www.youtube.com/watch?v=znqYo86deCg)

involves reconfiguring the BCM to enable the STFA settings.This re-configuration will enable the STFA (sales code LA5). Customer does not have Selectable Tire Fill Alert due to a late feature availability.Selectable Tire Fill Alert (STFA) Function: (https://www.youtube.com/watch?v=znqYo86deCg)

Customer does not have Selectable Tire Fill Alert due to a late feature availability.Selectable Tire Fill Alert (STFA) Function: (https://www.youtube.com/watch?v=znqYo86deCg)

involves reconfiguring the BCM to enable the STFA settings.This re-configuration will enable the STFA (sales code LA5). Customer does not have Selectable Tire Fill Alert due to a late feature availability.Selectable Tire Fill Alert (STFA) Function: (https://www.youtube.com/watch?v=znqYo86deCg)

Customer does not have Selectable Tire Fill Alert due to a late feature availability.Selectable Tire Fill Alert (STFA) Function: (https://www.youtube.com/watch?v=znqYo86deCg)

Customers may experience the following:A loud scraping, bump or clunking noise from the front suspension when going over bumps.

Stop Start Equipped Vehicles

DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE

Refer to Service Library and parts catalog for details.

sales code is present to restore rear defrost function. The switch is not provided in this kit and a service replacement part must be ordered. See service information procedure for switch replacement and below chart for replacement part numbers. vehicle has GTP+BNH+HAA replace HVAC control with pn 6BE36TRMAC vehicle has GTP+BNH-HAA replace HVAC control with pn 6BE37TRMAC vehicle has GTP+HAA-BNH replace HVAC control with pn 6BE40TRMAC vehicle has GTP-HAA-BNH replace HVAC control with pn 6BE41TRMAC Please ensure that the proper color code is used in place of the part TRM designation. For any questions call John Altsman at (248) 512-9361.

accompanied with a complaint of the fuel level gauge stuck at 7/8 of a tank, and the vehicle was built prior to 5/17/2019, please confirm electrical function of fuel level sensor call Anthony Reyes at (248) 462-4388. If no response in 15 minutes, proceed with repair. If vehicle was built on or after 5/17/2019, disregard this message and continue with normal repair.

Vehicles

Vehicles

This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.

This bulletin involves removing corrosion and refinishing the hem area on the vehicle door.

Vehicles

Vehicles

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

Simplification

Simplification

Terminal Detached From The Glass.

H 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification

G 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification

G 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 (Current) Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification

F 2018 - 2024 Jeep Wrangler (JL) and 2020 - 2024 Jeep Gladiator (JT) - Corrosion Warranty Claim Simplification

Gladiator (JT) - Corrosion Warranty Claim Simplification

Corrosion Warranty Claim Simplification

Corrosion Warranty Claim Simplification (Rev. D)

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

Water On Front Floor.

Window Stops Part Way Down.

switch 2) Please check the continuity on each pin of the switch based on the table found in the service Procedures. If after testing switch is still faulty, please call FCA Redacted Content. If no response after 15 minutes, proceeds with switch replacement.

This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim (Fig. 1) .Zinc Shim

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim. (Fig. 1) .Zinc Shim

Gladiator (JT) - Corrosion Warranty Claim Simplification (Rev. A)

Corrosion Warranty Claim Simplification (Rev. A)

Corrosion Warranty Claim Simplification

If no response in 15 minutes, proceed with repair. Please take pictures of the broken part and email the pictures to FCA Redacted Content.

Window Stops Part Way Down.

switch 2) Please check the continuity on each pin of the switch based on the table found in the service Procedures. If after testing switch is still faulty, please call FCA Redacted Content. If no response after 15 minutes, proceeds with switch replacement.

Corrosion Warranty Claim Simplification (Rev. B)

This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim (Fig. 1) .Zinc Shim

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

This bulletin involves inspecting and replacing any hinge exhibiting corrosion. The replacement hinge is equipped with a Zinc shim. (Fig. 1) .Zinc Shim

Gladiator (JT) - Corrosion Warranty Claim Simplification (Rev. A)

Corrosion Warranty Claim Simplification (Rev. A)

Corrosion Warranty Claim Simplification

Terminal Detached From The Glass.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Call FCA Redacted Content to confirm if T-case should be sent back to QEC.

B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)

When customer comes in for a cracked windshield, please note the location of crack and take pictures before repair. Please send pictures to FCA Redacted Content or load to the warranty claims system.

B Mopar Windshield Made With Corning Gorilla Glass (Rev. B)

When customer comes in for a cracked windshield, please note the location of crack and take pictures before repair. Please send pictures to FCA Redacted Content or load to the warranty claims system.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

If no response in 15 minutes, proceed with repair.

Call FCA Redacted Content to confirm if T-case should be sent back to QEC.

Prior to ordering a replacement tonneau cover, please call FCA Redacted Content.

A)

Customers may comment on the following:Front seat back panel is loose. Front seat back panel fell off. Gap between the seat back and seat assembly,Fig.1. Gap Between Seat Back and Panel

- All Dealers

If you have any questions call Asim @ (248) 296-1629.

Auto? does not work or is intermittently working when their device is plugged into the center console bin USB port. This replacing the center console USB cable.

? Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 34.4 to 34.42.

? WiFi hotspot gives ?No Internet? connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.41F to JR34.42F. NOTE: The National campaign for this FOTA update launched July 5, 2023.

? Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 34.4 to 34.42.

Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.

Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.

Blind Spot Alert Temporarily Unavailable Is Displayed On The EVIC

Customers may experience one or more of the following:Radio display screen flickers. Clock loses 6 seconds per day (JL with 5 inch screen). Ghost Touch issue, features, modes and App?s change without drivers input (does not affect rearview camera). Wireless connectivity pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.

Blind Spot Alert Temporarily Unavailable Is Displayed On The EVIC

published document)

published document)

Customers may experience one or more of the following:Radio screen goes black. Voice Recognition (VR) call contact name not recognized. In addition, the following software enhancements are also available:Bluetooth improvements. Navigation improvements.

Blind Spot Alert Temporarily Unavailable Is Displayed On The EVIC

Power Mirrors And/Or Power Door Locks Do Not Function

Customers may experience one or more of the following: Ghost Touch, features, modes and App?s changing without drivers input. Bluetooth pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.

Customers may experience one or more of the following: Can pair the wireless Bluetooth speaker the first time without issue when the automatic pair feature starts, while pressing the power button for first time. However, they are unable to pair any additional devices using the speaker?s Bluetooth pairing button. Unable to pair any devices.

Order the "R" part number for all orders:

Add felt shim 68736674AA - 43MM OD x 10mm ID x 1mm thick. "

this is normal and not a defect.

Low Washer Indicator May Be Illuminated.

If no response in 15 minutes, proceed with repair.

semi and full synthetic oils.

Low Washer Indicator May Be Illuminated.

If no response in 15 minutes, proceed with repair.

If no response in 15 minutes, proceed with repair.

bolster and installing a strap and push pin to help prevent this concern from happening again. Customers may comment on the following: The front passenger outer seat bolster cushion is missing

Detected Message

Therefore, a customer ordering a solid sunbonnet top received a mesh sunbonnet top, and vice versa. This can lead to customer dissatisfaction.

bolster and installing a strap and push pin to help prevent this concern from happening again. Customers may comment on the following: The front passenger outer seat bolster cushion is missing

If no response in 15 minutes, proceed with repair.

Detected Message

Please contact FCA Redacted Content prior to repair. If no response within 15 minutes, proceed with repair.

tightening the sun visor bracket attachment screws to specification. Customers may comment on the following:One or both of the sun visors squeak or rattle(metal to metal noise)when moved into desired position(s).

center console) side hinge, please call Ajay Sharma at (646) 236-2413 prior to any repairs. If no response in 15 mins,proceed with repairs.

Customers may experience the following:While driving a squeak can be heard coming from one or both rear seat latches.

have fault codes P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.

There may also be associated driveability issues. Upon further investigation, the following fault codes may be found in the PCM:

that were not used in this application. To simplify the design, the connector has been optimized and updated to a 10-pin configuration.

roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

This bulletin involves cleaning the piston heads and cylinder head combustion chambers to resolve a spark knock condition being caused by oil intrusion through the PCV system."

Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: Rough idle. Valvetrain noise. "

Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs.P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will now be P025A - Fuel Pump Module Control Circuit Open after the softwareupdate.In addition the customer may notice one or more of the following: The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within thisbulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replacedthe DTC P0300 may reoccur.If DTC P0300 is not present but other DTCs on this list below are present, performjust the software update. P0441 - EVAP Purge System Performance. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following: The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

DTC?s P00FD, P0562, P26F3

resolve a spark knock condition being caused by oil intrusion through the PCV system. The customer may describe a knocking or pinging noise coming from the engine upon acceleration.

Out (TPO) Of The XY230A Inline Connector

If no response within 15 minutes, proceed with repair. Engineering is investigating to determine root cause as warranty return keyfobs are determined trouble not found.

(ETL, ETM, ETN Engines)

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within thisbulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replacedthe DTC P0300 may reoccur.If DTC P0300 is not present but other DTCs on this list below are present, performjust the software update. P0441 - EVAP Purge System Performance. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following: The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

DTC?s P00FD, P0562, P26F3

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs.P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will now be P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following:The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafe speed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs.P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will now be P025A - Fuel Pump Module Control Circuit Open after the softwareupdate.In addition the customer may notice one or more of the following: The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

installed in the vehicle.

Please review the valve cover for a white paint dot/mark directly between the 2 cam actuators on the front of the valve cover. If found, please contact the following engineers for further information FCA Redacted Content, or FCA Redacted Content If no response in 15 minutes, proceed with repair.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within this bulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replaced the DTC P0300 may reoccur.If DTC P0300 is not present but other DTCs on this list below are present, perform just the software update. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will now be P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following:The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafe speed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within thisbulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replacedthe DTC P0300 may reoccur.If DTC P0300 is not present but other DTCs on this list below are present, performjust the software update. P0441 - EVAP Purge System Performance. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following: The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

DTC?s P00FD, P0562, P26F3

PCM: P0133, P0137, P0171, P0300, P2096. The root cause could be due to oil leaking from Bank 1 valve cover seal on to the 1/2 (Bank 1 downstream) O2 sensor. This can adversely affect the 1/2 O2 sensor signal reading and lead to listed DTCs. Before performing normal diagnostic routines for the above codes, check for the condition listed above.

the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.

PCM: P0133, P0137, P0171, P0300, P2096. The root cause could be due to oil leaking from Bank 1 valve cover seal on to the 1/2 (Bank 1 downstream) O2 sensor. This can adversely affect the 1/2 O2 sensor signal reading and lead to listed DTCs. Before performing normal diagnostic routines for the above codes, check for the condition listed above.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire. If DTC P0300 is present either alone or along with other DTCs listed within thisbulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right.If just the software flash was done without the right intake camshaft being replacedthe DTC P0300 may reoccur. If DTC P0300 is not present but other DTCs on this list below are present, performjust the software update. P0441 - EVAP Purge System Performance. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following: Pinging/detonation sound from the engine after warm up at 1000-1500 RPM at low speed. The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs: P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within this bulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replacedthe DTC P0300 may reoccur.If DTC P0300 is not present but other DTCs on this list below are present, performjust the software update. P0441 - EVAP Purge System Performance. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following: The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

DTC?s P00FD, P0562, P26F3

Please review the valve cover for a white paint dot/mark directly between the 2 cam actuators on the front of the valve cover. If found, please contact the following engineers for further information FCA Redacted Content, or FCA Redacted Content If no response in 15 minutes, proceed with repair.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs).P0300 - Multiple Cylinder Misfire.If DTC P0300 is present either alone or along with other DTCs listed within this bulletin the right intake camshaft MUST be replaced along with this software update (only if DTC P0300 is present). Refer to the detailedservice procedures available in DealerConnect>Service Library under: Service Info>09 - Engine, 3.6L / Cylinder Head / Camshaft, Engine / Removal and Installation>Right. If just the software flash was done without the right intake camshaft being replaced the DTC P0300 may reoccur.If DTC P0300 is not present but other DTCs on this list below are present, perform just the software update. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will now be P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following:The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafe speed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Out (TPO) Of The XY230A Inline Connector

If no response within 15 minutes, proceed with repair. Engineering is investigating to determine root cause as warranty return keyfobs are determined trouble not found.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following Diagnostic Trouble Codes (DTCs).P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following: The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

Desired Gear, D on PRNDL Flashing

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs.P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will now be P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following:The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafe speed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs.P0300 - Multiple Cylinder Misfire. P258B - Electronic Vacuum Pump Performance. C1252-92 - Vacuum Pump Control Circuit - Performance Or Incorrect Operation. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will now be P025A - Fuel Pump Module Control Circuit Open after the softwareupdate.In addition the customer may notice one or more of the following: The Anti-Lock Brake System (ABS) light illuminates. The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

be advised that the engine oil capacity is 5 quarts of oil.

Customers may experience the following condition:A loud whistle noise upon engine start up.

Upon further inspection, fault codes will be found in the powertrain control module (PCM) for P0441, P0443 or P0449. Fault codes may be either active or stored.

Upon further inspection, fault codes will be found in the powertrain control module (PCM) for P0441, P0443 or P0449. Fault codes may be either active or stored.

Upon further inspection, fault codes will be found in the powertrain control module (PCM) for P0441, P0443 or P0449. Fault codes may be either active or stored.

Chrysler, Jeep, Dodge & Ram vehicles and has provided direction on usage. BBAUA180AA CAN BE USED in the following vehicles equipped with stop/start technology: ?MP ? Jeep Compass ?JL ? Jeep Wrangler ?JT ? Jeep Gladiator ?RU ? Chrysler Pacifica RU NOTE: Modify the BBAUA180AA battery positive mold cover by trimming 3mm of rubber on left side & bottom. ?WK ? Jeep Grand Cherokee ?WD ? Dodge Durango WK/WD NOTE:A vent kit is being created now and will replace the existing tube with a longer one and add an elbow to it for routing (availability is TBD).

None of the seals from the PTU side will need to be replaced whenever the ATX stubshaftis replaced, even though V-seal (68408748A$) is in direct contact with the stubshaft,it will not avoid grease/oil leakage from transmission side. PTU V-seals are intended to act as a dust cover for stubshaft-PTU input shaft spline interface. PTU Input shaft seal (68408749A$) is intended to hold PTU oil and debris ingress; it should be replaced only if the fluid leakage is confirmed to be PTU oil and not ATX trans. fluid.

the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.

used as the reason for unit replacement. Visible ""glitter"" or debris in the pan does not justify complete unit replacements."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, visible ""glitter"" or debris in the pan and fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."

transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

Diagnostic Trouble Code (DTC) P08A6 Gear Lever Position Sensor System Multiple Sensor Correlation, Set Only In 4Low.

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch"

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch"

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch. "

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits.

the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all steps necessary to complete the Repair Procedure. If any steps are missed this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excessive play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all step necessary to complete the Repair Procedure. If any steps are missed this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excess play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all step necessary to complete the Repair Procedure. If any steps are missed this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excess play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

The power steering pump software must be updated, and vehicle configuration updated to ensure proper steering feel.

Steering (EHPS) software, if required. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excess play.This service bulletin repair will NOT correct a sustain steering shake, shimmy or vibration. If this repair is performed on a vehicle with those symptoms, that will cause a dissatisfied customer and a repeat visit to the dealer.

gasket for a leak in the oil pan area, please contact FCA Redacted Content. The CST will review root causing steps and suggest if the part is required to be returned back to FCA.

The customer may request to have the feature enabled which adds the ability to lock the rear axle differential, while 4-HI Off Road+ mode.

Setting DTC P08A6

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs.P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT)to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following:The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all steps necessary to complete the Repair Procedure. If any steps are missed, this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excessive play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all steps necessary to complete the Repair Procedure. If any steps are missed, this may lead to undesired handling characteristics. The customer may describe one or more of the following: Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excessive play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

The customer may request to have the feature enabled which adds the ability to lock the rear axle differential, while 4-HI Off Road+ mode.

Setting DTC P08A6

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all steps necessary to complete the Repair Procedure. If any steps are missed this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excessive play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all steps necessary to complete the Repair Procedure. If any steps are missed, this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excessive play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all steps necessary to complete the Repair Procedure. If any steps are missed this may lead to undesired handling characteristics. The customer may describe one or more of the following: Steering wander. Vehicle has a lead/pull to the right or left. The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excessive play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering/Linkage/Damper, Steering/Removal and Installation.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all step necessary to complete the Repair Procedure. If any steps are missed this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excess play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all steps necessary to complete the Repair Procedure. If any steps are missed this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excessive play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all step necessary to complete the Repair Procedure. If any steps are missed this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excess play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

Steering (EHPS) software, checking sales codes and performing vehicle reconfig, if required.Review and perform all step necessary to complete the Repair Procedure. If any steps are missed this may lead to undesired handling characteristics. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excess play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

The power steering pump software must be updated, and vehicle configuration updated to ensure proper steering feel.

Steering (EHPS) software, if required. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excess play.This Technical Service Bulletin (TSB) repair will NOT correct a sustained steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

Steering (EHPS) software, if required. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excess play.This Technical Service Bulletin (TSB) repair will NOT correct a sustain steering shake, shimmy or vibration. Video aid has been developed for this issue. Refer to the detailed service procedures available in DealerConnect>Service Library under: Service Info>19 - Steering / Linkage / Damper, Steering /Removal and Installation.

Steering (EHPS) software, if required. The customer may describe one or more of the following:Steering wander. Vehicle has a lead/pull to the right or left.The lead/pull will be more noticeable in hot ambient temperatures. Steering feels like it has excess play.This service bulletin repair will NOT correct a sustain steering shake, shimmy or vibration. If this repair is performed on a vehicle with those symptoms, that will cause a dissatisfied customer and a repeat visit to the dealer.

gasket for a leak in the oil pan area, please contact FCA Redacted Content. The CST will review root causing steps and suggest if the part is required to be returned back to FCA.

Setting DTC P08A6

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more ofthe following DTCs.P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT)to determine if a leak is present in the system. P1404 - EGR Close Position Performance. P1206 - Fuel Pump Control Module Open Circuit To Fuel Pump. Upon diagnosing the vehicle the technician may find DTC P1206 set before flashing the vehicle, the correct DTC will nowbe P025A - Fuel Pump Module Control Circuit Open after the software update.In addition the customer may notice one or more of the following:The customer may notice an ability to shift into 1st gear at an unsafespeed(MTX Only). Cluster displays "Autopark Engaged" even when autopark is no longer active.

A (XF1) Steering Damper Select 2018 - 2020 Jeep Wrangler (JL), 2020 Jeep Gladiator (JT) and 2018 Jeep Wrangler (JK)

A (XF1) Steering Damper Select 2018 - 2020 Jeep Wrangler (JL), 2020 Jeep Gladiator (JT) and 2018 Jeep Wrangler (JK)

the road surface (symptom is more prevalent in cold temperatures). This bulletin involves replacing the steering damper."

the road surface (symptom is more prevalent in cold temperatures). This bulletin involves replacing the steering damper."

the road surface (symptom is more prevalent in cold temperatures). This bulletin involves replacing the steering damper."

The customer may notice the following: A noise coming from the tailshaft of the steering column while turning.

The customer may notice the following: A noise coming from the tailshaft of the steering column while turning.

The customer may notice the following:A noise coming from the tailshaft of the steering column while turning.

available video instructing the technicians on how to properly diagnosis and repair this issue.

39.6.The repair procedure must be followed step by step. If the radio is not updated with the correct software level at the correct time the radio can be damaged. If the radio was damaged by not following the repairprocedure the radio may need to be replaced. Customers may experience one or more of the following: Lost radio presets. SXM favorite song not displaying/playing. Radio display screen is black, intermittent. Radio freeze intermittent. Incorrect navigation address/location/directions. Bluetooth pair or connection issue. Radio channel change by itself. SXM icon inoperative. Backup camera has black display screen. High pitch chime noise. Contact list not loading. Device not supported message. Remote app inoperative. Travel-Link fuel price incorrect. Backup camera gridlines missing. Unable to adjust volume. In addition the following enhancements are included: Heavy Duty (HD)Truck USB HUB improvements. HD Truck heated steering wheel improvements.

The customer may notice the following:A noise coming from the tailshaft of the steering column while turning.

available video instructing the technicians on how to properly diagnosis and repair this issue.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

The purpose of this informative Technical Service Bulletin (TSB) is to support the Network on the following topics: Discern the different kinds of connected service issues (onboard / offboard). Support the customer in his journey to open a request via Customer Care. Address on the correct actions to properly manage a customer complaining about the received assistance."

Library for specifications so a suitable alternative can be used

Key FOBIKs to service customer vehicles are limited to customer vehicles which are inoperable and a spare FOBIK is not available.

being delivered with only one key FOBIK due to a temporary semi conductor shortage. The customer may notice that they only have one key FOBIK when the vehicle was delivered or need an additional key FOBIK due to a lost or damaged keyFOBIK.Key FOBIKs to service customer vehicles are limited to customer vehicles which are inoperable and a spare FOBIK is not available.

Refer to instructions in service library. The position of the receiver attached to the vehicle header can be adjusted to change the ammount of force required to latch.

Key FOBIKs to service customer vehicles are limited to customer vehicles which are inoperable and a spare FOBIK is not available.

being delivered with only one key FOBIK due to a temporary semi conductor shortage. The customer may notice that they only have one key FOBIK when the vehicle was delivered or need an additional key FOBIK due to a lost or damaged keyFOBIK.Key FOBIKs to service customer vehicles are limited to customer vehicles which are inoperable and a spare FOBIK is not available.

Mopar Components - Warranty Coverage

Refer to instructions in service library. The position of the receiver attached to the vehicle header can be adjusted to change the ammount of force required to latch.

sunvisor body mounts.

The customer may describe one or more of the following:Instrument Panel Cluster (IPC) warnings for the Forward Collision Warning (FCW) informing the driver to apply the brakes. Brakes may intermittently apply unexpectedly together with IPC warnings. The following software enhancements are also available:Allows customers to turn off the FCW indefinitely, rather than resetting to ?ON? at each key cycle(Japan and South Korea only). System improvements to enhance the FCW system hazard detection which may reduce nuisance actions and warnings from incorrectly identified structures and hazards, which can in rare circumstances cause an unwarranted brake event.

Optional harness 82216416A$ referenced in I-sheet is used for Wrangler only without factory trailer tow.

The customer may describe one or more of the following:Instrument Panel Cluster (IPC) warnings for the Forward Collision Warning (FCW) informing the driver to apply the brakes. Brakes may intermittently apply unexpectedly together with IPC warnings. The following software enhancements are also available:Allows customers to turn off the FCW indefinitely, rather than resetting to ?ON? at each key cycle(Japan and South Korea only). System improvements to enhance the FCW system hazard detection which may reduce nuisance actions and warnings from incorrectly identified structures and hazards, which can in rare circumstances cause an unwarranted brake event.

Customers may comment on one or more of the following:Click or clunk from the rear of the vehicle. A missing or loose rear brake caliper adapter boltFig.1.Missing And Loose Caliper Adapter Bolts

The customer may describe one or more of the following:Instrument Panel Cluster (IPC) warnings for the Forward Collision Warning (FCW) informing the driver to apply the brakes. Brakes may intermittently apply unexpectedly together with IPC warnings. The following software enhancements are also available:Allows customers to turn off the FCW indefinitely, rather than resetting to ?ON? at each key cycle(Japan and South Korea only). System improvements to enhance the FCW system hazard detection which may reduce nuisance actions and warnings from incorrectly identified structures and hazards, which can in rare circumstances cause an unwarranted brake event.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one of the following Diagnostic Trouble Code (DTC) has been set: B1783-01 - Stop Lamp Control - General Electrical Failure. The customer may also comment or note that the DTC set after the installation of a Mopar or an aftermarket trailer brake controller.The 12 volt back feed of the aftermarket trailer brake controller into the redundant connection between the Body Control Module (BCM) and the Anti Lock Brake Module (ABS) is causing a design intent diagnostic detection of the stop lamps.Software enhancement includes:Removal of the warning lamp associated with this DTC so an aftermarket trailer brake controller can be used.

Optional harness 82216416A$ referenced in I-sheet is used for Wrangler only without factory trailer tow.

Optional harness 82216416A$ referenced in I-sheet is used for Wrangler only without factory trailer tow.

Mounting bracket has grease present which may have damaged plastic part. Please call Adam Rose (586) 804-4315) for cleaning procedure prior to replacing any parts. If no response in 15 minutes, proceed with repair after thoroughly cleaning grease off metal mounting bracket as follows. Clean metal mounting bracket with brake cleaner sprayed onto shop rag, rub on mounting surface until grease is removed. Do not spray brake cleaner directly onto seat. Replacement plastic part may fail in same way if grease is not removed.

TPM Lamp On.

TPM Lamp On.

clearing.

Diagnostic Trouble Codes (DTCs) P20E8 ? Reductant Pressure Too Low and/or P208B ? Reductant Pump 1 Control Performance Set.

If the Filter is restricted or blocked then replace the part.

To maintain production and service requirements, FOBIKs affected by the shortage will be available on an ?as required basis?. This FOBIK should only be ordered in the event the vehicle is inoperable, and there are no other FOBIKs available. It is requested the customer uses their spare FOBIK until supply is once again available.

To maintain production and service requirements, FOBIKs affected by the shortage will be available on an ?as required basis?. This FOBIK should only be ordered in the event the vehicle is inoperable, and there are no other FOBIKs available. It is requested the customer uses their spare FOBIK until supply is once again available. On some 2021 vehicles, they will be sold with only one FOBIK, and will have sales code ?GXZ?. For these vehicles a CSN (Customer Satisfaction Notification) will be released to replace the FOBIK once supply is available. A unique part number will be used for this campaign. For these vehicles, only order a replacement FOBIK in a vehicle down situation. Due to the global shortage, once service inventory of this part is depleted, there may not be any additional parts available for service for an extended period of time. This may cause customer dissatisfaction and extended vehicle down time. We appreciate everyone?s consideration and cooperation to only order this part in a vehicle down situation.

Customers may experience one or more of the following:Radio display screen flickers. Radio resets with RPM less than 1000 RPM (DT and JL with 3.0L Diesel). Clock loses 6 seconds per day (JL with 5 inch screen). Ghost Touch, features, modes and App?s changing without drivers input. Bluetooth pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.

To maintain production and service requirements, FOBIKs affected by the shortage will be available on an ?as required basis?. This FOBIK should only be ordered in the event the vehicle is inoperable, and there are no other FOBIKs available. It is requested the customer uses their spare FOBIK until supply is once again available.

To maintain production and service requirements, FOBIKs affected by the shortage will be available on an ?as required basis?. This FOBIK should only be ordered in the event the vehicle is inoperable, and there are no other FOBIKs available. It is requested the customer uses their spare FOBIK until supply is once again available. On some 2021 vehicles, they will be sold with only one FOBIK, and will have sales code ?GXZ?. For these vehicles a CSN (Customer Satisfaction Notification) will be released to replace the FOBIK once supply is available. A unique part number will be used for this campaign. For these vehicles, only order a replacement FOBIK in a vehicle down situation. Due to the global shortage, once service inventory of this part is depleted, there may not be any additional parts available for service for an extended period of time. This may cause customer dissatisfaction and extended vehicle down time. We appreciate everyone?s consideration and cooperation to only order this part in a vehicle down situation.

Customers may experience one or more of the following:Radio display screen flickers. Radio resets with RPM less than 1000 RPM (DT and JL with 3.0L Diesel). Clock loses 6 seconds per day (JL with 5 inch screen). Ghost Touch, features, modes and App?s changing without drivers input. Bluetooth pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.

Reference Master Tech article released in January 2026 for updated diagnostic and testing procedures. Master Tech link: https: //mastertech.playerlync.net/app/player/p2tQVm

Reference Master Tech article released in December 2025 for updated diagnostic and testing procedures. Master Tech link: https: //mastertech.playerlync.net/app/player/p2tQVm

"

Please contact FCA REDACTED CONTENT. ~ If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Hotline

Required, MVP Hotline

Hotline

Hotline

Customers may experience one or more of the following:One or both of the front splash shields are rubbing on the tires while driving over 88 kph (55 MPH), or with strong cross winds. Rattle noise can be heard from either front wheel area while driving.

Customers may experience one or more of the following: One or both of the front splash shields are rubbing on the tires while driving over 88 kph (55 MPH), or with strong cross winds. Rattle noise can be heard from either front wheel area while driving.

system

E adds 2024 model year vehicles and updates the Collision Service Bulletin number

B)