2015 Jeep Compass TSBs

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Control Module (WCM) with new software. A small number of customers may experience a no crank, no start or Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs): B1A25 - INVALID KEY. B1A29 - SKIM Basestation Mismatch.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

reprogramming the Powertrain Control Module (PCM) with new software. Some customers may see erroneous illuminated malfunction indicator lamps (MIL) and have a hard start cold condition. ? P219A Bank 1 Air Fuel Ratio Imbalance ? P050B Cold Start Ignition Timing Performance

battery; If the battery is dead due to radiator cooling fan stuck on (Fan runs during battery charging with key off). Before replacing the TIPM for this issue please contact Saji John at cell (248) 890-0324, or Rob Samko at cell (248) 379-4093. If response is not received within 15 minutes, continue with normal repair procedure.

Gurdial Dhami at cell (226) 346-7919. If you do not receive a return call after 15 minutes, please proceed with repair.

Gurdial Dhami at cell (226) 346-7919. If you do not receive a return call after 15 minutes, please proceed with repair.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

Gurdial Dhami at cell (226) 346-7919. If you do not receive a return call after 15 minutes, please proceed with repair.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

reprogramming the Powertrain Control Module (PCM) with new software. Some customers may see erroneous illuminated malfunction indicator lamps (MIL) and have a hard start cold condition. * P219A Bank 1 Air Fuel Ratio Imbalance * P050B Cold Start Ignition Timing Performance

Control Module (WCM) with new software. A small number of customers may experience a no crank, no start or Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs): B1A25 - INVALID KEY. B1A29 - SKIM Basestation Mismatch.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

battery; If the battery is dead due to radiator cooling fan stuck on (Fan runs during battery charging with key off). Before replacing the TIPM for this issue please contact Saji John at cell (248) 890- 0324, or Rob Samko at cell (248) 379-4093. If response is not received within 15 minutes, continue with normal repair procedure.

battery; If the battery is dead due to radiator cooling fan stuck on (Fan runs during battery charging with key off). Before replacing the TIPM for this issue please contact Saji John at cell (248) 890- 0324, or Rob Samko at cell (248) 379-4093. If response is not received within 15 minutes, continue with normal repair procedure.

Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE

For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

this is normal and not a defect.

semi and full synthetic oils.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair

If no response is received within 15 minutes, then proceed with required repair.~

Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair

If no response is received within 15 minutes, then proceed with required repair.~

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Dennis Gauthier at cell (248) 613-9756. If no response is received within 15 minutes, then proceed with required repair

If no response is received within 15 minutes, then proceed with required repair.~

Coolant bottle recovery hose may not be properly attached.

The key codes were not recorded during manufacturing.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

installed in the vehicle.

The customer may describe the engine is consuming oil.

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

(248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P0335 - Crankshaft Position Sensor Circuit. P0456 - Evap System Small Leak.** P219A - Bank 1 Air Fuel Ratio Imbalance. P050B - Cold Start Ignition Timing Performance. Other software enhancements included that will address some customers concerns: **Cruise control acceleration rate may be considered objectionable to some customers if the accel button is held down. Engine is hard to start at temperatures -29C (-20F) for vehicles utilizing E15 fuel only.**

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

The customer may describe the engine is consuming oil.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination and/or any of the following: ? Cruise Control acceleration feels to fast at low speeds (35 mph / 56 kph). ? Engine is hard to start when cold Upon further investigation, the technician may find Diagnostic Trouble Codes (DTCs): P219A - Bank 1 Air Fuel Ratio Imbalance. P050B - Cold Start Ignition Timing Performance.

The customer may describe the engine is consuming oil.

would like to have the bulb and the entire lamp assembly replaced and returned for analysis. If you have any questions, please contact Brigitte Wicks at cell (248) 202-9869. Also please make sure to send the part to Brigitte's attention when it is returned. Thank you.

Vijay Thiruvenkatachary at cell (906) 281-8495.~ Before replacing the Left Downstream (2/2) O2 Sensor on a 3.6L JK due to a P0157 fault code, please call Jerry Tomlin at cell (248) 202-5329. ~ Engineering would like determine whether the sensor has been contaminated with oil.~ If no response is received within 15 minutes, then continue with repair. For all other fault codes, please perform the applicable diagnostic routine.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: **P0335 - Crankshaft Position Sensor Circuit. P0456 - Evap System Small Leak.** P219A - Bank 1 Air Fuel Ratio Imbalance. P050B - Cold Start Ignition Timing Performance. Other software enhancements included that will address some customers concerns: **Cruise control acceleration rate may be considered objectionable to some customers if the accel button is held down. Engine is hard to start at temperatures -29C (-20F) for vehicles utilizing E15 fuel only.**

(248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: P0335 - Crankshaft Position Sensor Circuit. P0456 - Evap System Small Leak. P219A - Bank 1 Air Fuel Ratio Imbalance. P050B - Cold Start Ignition Timing Performance.The following software enhancement is also available: Engine is hard to start at temperatures -29C (-20F) for vehicles utilizing E15 fuel only (Sales Code ECN). Cruise control acceleration rate may be considered objectionable to some customers if the accel button is held down.

Gaurav Saxena at cell (248) 260-0583 or Tim Kraft at cell (248) 766-5826 ~ IMPORTANT - do not reset the HFM, clear codes or perform a battery reset before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. Seeking vehicles with HFM in a locked state, inoperative, or offline. If unable to reach this person within 15 minutes, then proceed with the necessary repair.

If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.

Manverter changed to Maniverter. Alternate Transportation section wording revised. Customer Satisfaction Notification S18 - Engine Oil Consumption The engine on about 480 of the above vehicles may experience low oil pressure originating from an oil consumption issue. This may result in oil starvation and possible engine failure. The engine long block assembly must be replaced on the involved vehicles.

experience low oil pressure originating from an oil consumption issue. This may result in oil starvation and possible engine failure. The engine long block assembly must be replaced on the involved vehicles.

ALSO CUSTOMERS MAY EXPERIENCE CRUISE CONTROL ACCELERATION FEELS TO FAST AT LOW SPEEDS AND WHEN ITS COLD ENGINE IS HARD TO START *CN

catalytic converter efficiency

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.

Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Remote Start will all function as expected but the Remote Start Cancel button requires a double (2x) button press versus the original single (1x) button press to cancel the remote start function and turn the vehicle off.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.

A small number of customers may experience slight reduction in transmission performance after a recent repair. This may be due to an overfill condition after incorrect fill procedures being followed at the time of the repair.

A small number of customers may experience slight reduction in transmission performance after a recent repair. This may be due to an overfill condition after incorrect fill procedures being followed at the time of the repair.

with new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever

new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever

A small number of customers may experience slight reduction in transmission performance after a recent repair. This may be due to an overfill condition after incorrect fill procedures being followed at the time of the repair.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

with new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever

new Hydraulic Clutch Tube 05273429A$ to avoid interference with shift lever

Module (TCM) with the latest available software. Customers may experience one of the following: ? Calibration will prevent unintentional engagement of AutoStick (Manual Mode) when shifter is bumped or tapped. ? Poor shift quality or a delayed shifts.

A small number of customers may experience slight reduction in transmission performance after a recent repair. This may be due to an overfill condition after incorrect fill procedures being followed at the time of the repair.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

A)

(PM)

bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.

B)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

A)

(PM)

bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

A)

(PM)

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

A low frequency moan noise is heard during the first brake apply when in reverse, while the vehicle is cold or has been parked for several hours.An audio sound file of the moan noise can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing.If the low frequency moan noise can be verified, the addition of the anti-vibration bracket may correct the condition.

A low frequency moan is heard during the first brake apply when in reverse while the vehicle is cold or has been parked for several hours. An audio sound file of the moan can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing. If the low frequency moan can be verified, the addition of the anti-vibration bracket may correct the condition.

A low frequency moan noise is heard during the first brake apply when in reverse, while the vehicle is cold or has been parked for several hours.An audio sound file of the moan noise can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing.If the low frequency moan noise can be verified, the addition of the anti-vibration bracket may correct the condition.

A low frequency moan noise is heard during the first brake apply when in reverse, while the vehicle is cold or has been parked for several hours. An audio sound file of the moan noise can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing. If the low frequency moan noise can be verified, the addition of the anti-vibration bracket may correct the condition.

A low frequency moan noise is heard during the first brake apply when in reverse, while the vehicle is cold or has been parked for several hours. An audio sound file of the moan noise can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing. If the low frequency moan noise can be verified, the addition of the anti-vibration bracket may correct the condition.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

A low frequency moan noise is heard during the first brake apply when in reverse, while the vehicle is cold or has been parked for several hours.An audio sound file of the moan noise can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing.If the low frequency moan noise can be verified, the addition of the anti-vibration bracket may correct the condition.

A low frequency moan is heard during the first brake apply when in reverse while the vehicle is cold or has been parked for several hours. An audio sound file of the moan can be found in DealerCONNECT> TechCONNECT under: Service Info> 05 - Brakes> 05 - Brakes, Base> Diagnosis and Testing. If the low frequency moan can be verified, the addition of the anti-vibration bracket may correct the condition.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

The customer may describe a water leak at the rear of the sunroof when using a high pressure touchless car wash.

The customer may notice that the power door lock will not auto lock when the vehicle starts moving forward.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

B)

Look for folded hose at the clamped end of the hose 2) Part Number 4596198. If leak is coming from the cap, change only the cap and retest.~ For any questions about this TechTip call Sergio Santi. cell phone: (248) 613-1978 If no response in 15 minutes, please continue with repair.~

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

If no response in 15 minutes, continue with repair.

The steering wheel is off center.

The steering wheel is off center.

Incorrect wheel rim size printed on certification label.