2009 Jaguar XF TSBs

13MY onwards.

Please destroy all previous versions.

ISSUE: JLR WOULD ADVISE ALL DEALERS THAT JTB00280 HAS BEEN TEMPORARILY REMOVED FROM TOPIX DUE TO AN UNAVOIDABLE PARTS SUPPLY ISSUE REFERENCE THE OVERHEAD CONSOLE REPAIR KIT C2Z25623. CAUSE: JLR ARE WORKING TO RELEASE A NEW FIX FOR THIS ISSUE ON XF AND THE TSB WILL BE RE-RELEASED ONCE PARTS ARE AVAILABLE TO MEET DEMAND."

CAUSE: THE DESIGN OF THE STUB PIPE WAS NOT ADEQUATE AND COULD RESULT IN THE PIPE SPLITTING."

ISSUE: SEAT MOVEMENT MAYBE RESTRICTED ON SOME VEHICLES THAT HAS THE SEAT MEMORY FUNCTION. CAUSE: IF AN OBSTRUCTION IS ENCOUNTERED WHILE THE SEAT IS IN MOTION, THE SEAT WILL STOP MOVING AND FURTHER MOVEMENT WILL BE RESTRICTED UNTIL THE SEAT HAS BEEN RESET."

ISSUE: SEAT MOVEMENT MAYBE RESTRICTED ON SOME VEHICLES THAT HAS THE SEAT MEMORY FUNCTION. CAUSE: IF AN OBSTRUCTION IS ENCOUNTERED WHILE THE SEAT IS IN MOTION, THE SEAT WILL STOP MOVING AND FURTHER MOVEMENT WILL BE RESTRICTED UNTIL THE SEAT HAS BEEN RESET."

THE IPOD/IPHONE USB CABLE ONLY, THE PLAYBACK SOUND MAY BE DISTORTED OR JUMPS/SKIPS. CAUSE: UNKNOWN, CURRENTLY UNDER INVESTIGATION."

CAUSE: DAMAGE/MARKING CAUSED BY OBJECT IMPACT AGAINST THE LENS. STAINING/DISCOLORATION CONTAMINATION CAUSED BY USING ANY TYPE OF CLEANING PRODUCT ON LENS."

ISSUE: JLR WOULD ADVISE ALL DEALERS THAT JTB00280 HAS BEEN TEMPORARILY REMOVED FROM TOPIX DUE TO AN UNAVOIDABLE PARTS SUPPLY ISSUE REFERENCE THE OVERHEAD CONSOLE REPAIR KIT C2Z25623. CAUSE: JLR ARE WORKING TO RELEASE A NEW FIX FOR THIS ISSUE ON XF AND THE TSB WILL BE RE-RELEASED ONCE PARTS ARE AVAILABLE TO MEET DEMAND."

MODELS XF AND XK 2009. *PE

*PE

IT MIGHT BE CAUSED BY A SEPARATION OF THE HEAT DEFLECTOR SHIELD. *RM

SUPPLIED WITH EXCESSIVE SILICON CARBIDE LEFT IN THE UNITS. THIS CAN CAUSE PREMATURE WEAR ON THE DIFFERENTIAL PINION HEAD AND TAIL CARRIER BEARINGS, RESULTING IN UNACCEPTABLE DIFFERENTIAL NOISE AND DRIVELINE VIBRATION. *PE

Any of the following DTCs (indicating an air intake system leak) could be stored in the Powertrain Control Module (PCM) ? P2187, P2189, P0505, P0507.

Diagnostic Trouble Code (DTC) B1B87-31, stored in Driver Seat Module (DSM) or Passenger Seat Module (PSM) Note: that the seat height motor is supplied as part of the cushion sub-assembly or motor sub-assembly (depending on model)

housing seam.

OR STALL FOLLOWING A HOT SOAK OF 15-20 MINUTES. CAUSE: THIS MAY BE CAUSED BY THE FUELING CALIBRATION NOT BEING ROBUST FOR WINTER BLEND 10% ETHANOL FUEL."

CAUSE: CYLINDER COVER MAY HAVE BEEN INCORRECTLY FITTED AT PDI OR AFTER EMERGENCY VEHICLE ENTRY."

CAUSE: UNKNOWN ENGINEERING INVESTIGATION ON-GOING."

POWER TRAIN CONTROL MODULE (PCM) CAUSE: THERE IS A CPU RESPONSE TIME ERROR DURING THE VEHICLE SHUTDOWN PROCEDURE, THIS IS A PROBLEM WITH THE POWER TRAIN CONTROL MODULE (PCM)"

THEREFORE WOULD APPRECIATE MORE INFORMATION TO AID INVESTIGATIONS."

CAUSE: POOR FUEL QUALITY OR FUEL CONTAMINANTS BLOCKING THE HOLES IN THE FUEL INJECTOR."

THEREFORE WOULD APPRECIATE MORE INFORMATION TO AID INVESTIGATIONS. KNOWN ISSUES HAVE BEEN RESOLVED AND ASSURED VINS FOR EFFECTED MODELS ARE: JAGUAR XF (X250) - U46731 JAGUAR XF (X250) - PUNE - T02417 JAGUAR XK (X150) - B56550"

THEREFORE WOULD APPRECIATE MORE INFORMATION TO AID INVESTIGATIONS. KNOWN ISSUES HAVE BEEN RESOLVED AND ASSURED VINS FOR EFFECTED MODELS ARE: JAGUAR XF (X250) - U46731 JAGUAR XK (X150) - B56550"

ACTION: PLEASE REFER TO THE PROCEDURE BELOW FOR INFORMATION ON HOW TO ACCESS THE NEW INFORMATION THROUGH SDD."

A COOLANT LEAK IS FOUND FROM THE SEAM ON COOLANT PIPE (AJ8 9664). SEE THE ATTACHED FILE FOR AN EXAMPLE OF THE LEAK LOCATION. CAUSE: A PROCESS ISSUE AT COMPONENT SUPPLIER"

ISSUE: ON INVESTIGATION OF WARRANTY RETURNS IT HAS BEEN NOTED THAT THE ENGINE-COMPARTMENT LID LATCH HAS BEEN LUBRICATED. CAUSE: LUBRICANT APPLIED TO THE ENGINE-COMPARTMENT LID LATCH DURING ROUTINE SERVICING OR FOR ANY OTHER REASON WILL, OVER TIME, MIGRATE INTO THE AJAR SWITCH AND CAUSE DAMAGE TO THE SWITCH."

CHECK ENGINE LIGHT BEING DISPLAYED, OR A COMBINATION OF THESE SYMPTOMS. CAUSE: DTC'S CAPTURED BY THE VEHICLE ELECTRONIC MODULES SHOULD BE USED TO AID INVESTIGATION OF A VEHICLE WITH THIS ISSUE TO HELP IDENTIFY ROOT CAUSE. IN SOME CASES, THE FUEL PUMP DRIVER MODULE - C2C35672, THE IN TANK FUEL PUMP - C2D28002 OR THE CONNECTIONS TO THESE PARTS MAY BE AT FAULT."

ISSUE: ON INVESTIGATION OF WARRANTY RETURNS IT HAS BEEN NOTED THAT THE ENGINE-COMPARTMENT LID LATCH HAS BEEN LUBRICATED. CAUSE: LUBRICANT APPLIED TO THE ENGINE-COMPARTMENT LID LATCH DURING ROUTINE SERVICING OR FOR ANY OTHER REASON WILL, OVER TIME, MIGRATE INTO THE AJAR SWITCH AND CAUSE DAMAGE TO THE SWITCH."

XJ AND XF ALL WHEEL DRIVE VEHICLES ONLY CAUSE: ENGINEERING ARE INVESTIGATING THE CAUSE OF THIS ISSUE AND REQUIRE THE FLOWING ACTION."

CAUSE: CYLINDER COVER MAY BE DAMAGED OR HAVE BEEN INCORRECTLY FITTED AT PDI OR AFTER EMERGENCY VEHICLE ENTRY."

CAUSE: CYLINDER COVER MAY HAVE BEEN INCORRECTLY FITTED AT PDI OR AFTER EMERGENCY VEHICLE ENTRY."

HIGHER TIME IN SERVICE VEHICLES, WHERE INSUFFICIENT PERFORMANCE OF THE AIR CONDITIONING COMPRESSOR HAS BEEN FOUND TO BE THE ROOT CAUSE OF THE ISSUE. COMPRESSOR PART NO. C2D2790 & C2Z4345 ACTION: THE COMPRESSOR SUPPLIER IN CONJUNCTION WITH JAGUAR ENGINEERING HAVE MADE IMPROVEMENTS TO THE COMPRESSORS TO IMPROVE THEIR SERVICE LIFE AND RELIABILITY, AND TWO IMPROVED COMPRESSORS HAVE BEEN SUPPLIED TO PARTS OPERATIONS"

HIGHER TIME IN SERVICE VEHICLES, WHERE INSUFFICIENT PERFORMANCE OF THE AIR CONDITIONING COMPRESSOR HAS BEEN FOUND TO BE THE ROOT CAUSE OF THE ISSUE. COMPRESSOR PART NO. C2D2790 & C2Z4345 ACTION: THE COMPRESSOR SUPPLIER IN CONJUNCTION WITH JAGUAR ENGINEERING HAVE MADE IMPROVEMENTS TO THE COMPRESSORS TO IMPROVE THEIR SERVICE LIFE AND RELIABILITY, AND TWO IMPROVED COMPRESSORS HAVE BEEN SUPPLIED TO PARTS OPERATIONS C2D2790 SUPERSEDES TO C2D38105 C2Z4345 SUPERSEDES TO C2D38106 PLEASE ENSURE THAT THE LATER PART NUMBER IS FITTED TO ANY VEHICLE THAT IS SUFFERING FROM LACK OF COMPRESSOR PERFORMANCE."

HIGHER TIME IN SERVICE VEHICLES, WHERE INSUFFICIENT PERFORMANCE OF THE AIR CONDITIONING COMPRESSOR HAS BEEN FOUND TO BE THE ROOT CAUSE OF THE ISSUE. COMPRESSOR PART NO. C2D2790 & C2Z4345 ACTION: THE COMPRESSOR SUPPLIER IN CONJUNCTION WITH JAGUAR ENGINEERING HAVE MADE IMPROVEMENTS TO THE COMPRESSORS TO IMPROVE THEIR SERVICE LIFE AND RELIABILITY, AND TWO IMPROVED COMPRESSORS HAVE BEEN SUPPLIED TO PARTS OPERATIONS C2D2790 SUPERSEDES TO C2D38105 C2Z4345 SUPERSEDES TO C2D38106. PLEASE ENSURE THAT THE LATER PART NUMBER IS FITTED TO ANY VEHICLE THAT IS SUFFERING FROM LACK OF COMPRESSOR PERFORMANCE."

ISSUE: FUEL INJECTOR CONCERNS, (APPLICABLE TO 5.0 AJ133 GASOLINE ENGINES), LEADING TO POTENTIAL PROBLEMS SUCH AS POOR RUNNING, POOR FUEL ECONOMY, HARD STARTING, ROUGH IDLE, MISFIRES AND ENGINE DETONATION. CUSTOMER SYMPTOMS MAY INCLUDE THE ENGINE CHECK LAMP ILLUMINATED WHICH MAYBE ACCOMPANIED WITH A MISFIRE/ENGINE VIBRATION AT IDLE. MISFIRE CODES (P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0316) ARE STORED IN THE PCM DEPENDENT ON THE AFFECTED CYLINDER(S). CAUSE: POOR FUEL QUALITY OR FUEL CONTAMINANTS RESTRICTING THE FUEL INJECTOR FLOW RATE."

CUSTOMER EXPERIENCES THE ENGINE OVERHEATING. CAUSE: THE REFILL PROCEDURE HAS NOT BEEN COMPLETED CORRECTLY, RESULTING IN INSUFFICIENT COOLANT IN THE ENGINE."

CAUSE: WHEN CHARGING A BATTERY (BOTH PRIMARY AND SECONDARY) WITH A BMS (BATTERY MONITORING SYSTEM) FITTED, THE EARTH FROM THE CHARGER MUST BE CONNECTED TO A SUITABLE CHASSIS OR ENGINE EARTH (CHECK TOPIX FOR APPROPRIATE LOCATION). THIS ALLOWS THE BMS TO SEE THE CURRENT GOING INTO THE BATTERY. HOWEVER WHEN USING A DIAGNOSTIC CHARGER FROM MIDTRONICS SUCH AS GR1, GRX OR GR8(110 VOLTS) THIS CONNECTION PROCESS CAN CAUSE AN INCORRECT BATTERY ANALYSIS DUE TO THE EXTRA RESISTANCE IN THE WIRING WHEN CONNECTED TO A CHASSIS OR ENGINE EARTH."

CAUSE: CYLINDER COVER MAY HAVE BEEN INCORRECTLY FITTED AT PDI OR AFTER EMERGENCY VEHICLE ENTRY."

CAUSE: UNKNOWN ENGINEERING INVESTIGATION ON-GOING."

STALL FOLLOWING A HOT SOAK OF 15-20 MINUTES. CAUSE: THIS MAY BE CAUSED BY THE FUELING CALIBRATION NOT BEING ROBUST FOR WINTER BLEND 10% ETHANOL FUEL."

*LJ

HARD STARTING, ROUGH IDLE, MISFIRES AND ENGINE DETONATION. *JS

*PE

ON VEHICLES FITTED WITH TIRE PRESSURE MONITORING SYSTEM (TPMS) ONLY, THE FOLLOWING ISSUES HAVE BEEN IDENTIFIED-VALVE STEM MAY BE DAMAGED DURING MANUAL TIRE PRESSURE CHECKING WHEN EITHER THE VALVE CAP IS REMOVED OR WHEN AN AIRLINE IS ATTACHED; THE LOW TIRE PRESSURE WARNING WILL BE ILLUMINATED AND ASSOCIATED INSTRUMENT PACK MESSAGES DISPLAYED. MODELS XF, XJ, XK. *PE

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

If blockage occurs while ACC is being used, ?Driver Intervene? and/or "Radar sensor blocked" message will appear on the cluster and DTC C1A67-97 is also set. Blockage can also occur when ACC is not being used.

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

an audible warning to indicate that the hood is not latched correctly. Upon further inspection, the hood is correctly latched.

Retailers are testing the primary battery using the Midtronics EXP-1080 tester which is reporting the battery is serviceable. The vehicle then returns with the same Customer concern of ECO Stop/Start inoperative. If a Midtronics GRX-3080 is used, the primary battery fails the test. Replacement of the primary battery resolves the concern.

JLR are currrently investigating a hand held battery tester to replace the Midtronics EXP-1080. The Midtronics EXP-1080 can be used for PD1 and battery checks.

indicator gives an audible warning to indicate that the hood is not latched correctly when the hood has been correctly latched.

LEVEL DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY FROM SDD RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD."

AVAILABLE, IS NOT SHOWING AS PAIRED BUT IS AVAILABLE, IS DIFFICULT TO PAIR, AUDIO FRAGMENTS WHEN STREAMING MUSIC AND/OR OTHER UNEXPECTED BEHAVIOR. CAUSE: THIS CAN BE A RESULT OF REDUCED PHONE POWER DUE TO THE FOLLOWING:- BATTERY LIFE SOFTWARE UPDATE ON THE CUSTOMERS DEVICE, OTHER APPLICATIONS RUNNING IN THE BACKGROUND ON THE CUSTOMERS DEVICE (SUCH AS GAMES, SOCIAL MEDIA APPS, SEARCHING FOR NUMEROUS PAIRED DEVICES). A BREAK IN THE LINE OF SIGHT FROM THE IAM TO THE CUSTOMER DEVICE (E.G. DEVICE IN POCKET CAUSING ATTENUATION BY THE HUMAN BODY). ANOMALIES INTRODUCED WITH SOFTWARE UPDATES OF DEVICE THAT MAY REDUCE THE EFFECTIVENESS OF AUTHENTICATION BETWEEN THE CUSTOMER DEVICE AND THE VEHICLE. NOTE: THESE ISSUES ARE WELL DOCUMENTED ON OFFICIAL PHONE MANUFACTURERS SUPPORT WEB SITES."

CAUSE: THIS MAY BE CAUSED BY ELECTRICAL INPUTS FROM THE VEHICLE SYSTEM."

CAUSE THE BATTERY STORAGE PROCESS HAS NOT BEEN CORRECTLY FOLLOWED UPON VEHICLE DELIVERY AND FOLLOWING A PDI."

CONTROL MODULES CAUSE: INCORRECT DIAGNOSIS. "

LEVEL DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY FROM SDD RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD."

FOR FAULT CODES LOGGED IN THE KVM (KEYLESS VEHICLE MODULE) ALSO KNOWN AS THE RFA (REMOTE FUNCTION ACTUATOR) F000- 63/U3000-63, CONTROL MODULE - CIRCUIT/ COMPONENT PROTECTION TIME-OUT IS LOGGED. CAUSE THIS DTC IS SET WHEN THE KVM HAS GONE THROUGH A SELF RESET"

CAUSE: THIS MAY BE CAUSED BY A CORRODED WIRING HARNESS AT THE FRONT AND/OR REAR BUMPER HARNESSES."

IF BLOCKAGE OCCURS WHILE ACC IS BEING USED, DRIVER INTERVENE AND/OR ""RADAR SENSOR BLOCKED"" MESSAGE WILL APPEAR ON THE CLUSTER AND DTC C1A67-97 IS ALSO SET. BLOCKAGE CAN ALSO OCCUR WHEN ACC IS NOT BEING USED. CAUSE ""RADAR SENSOR BLOCKED"" INDICATES THAT THE ADAPTIVE SPEED CONTROL SYSTEM'S VISIBILITY HAS BEEN REDUCED DUE TO AN OBSTRUCTION. ACC CONTINUALLY SCANS FOR OBJECTS AHEAD AND, IF IT SEES NO OBJECTS I.E. VEHICLES, ROAD SIGNS, LAMPPOSTS, GUARD RAILS ETC, IT WILL INDICATE A BLOCKAGE EVEN IF THE ACC IS NOT USED. THE C1A67-97 DTC FLAGS A RADAR BLOCKAGE SITUATION AND NOT A SYSTEM FAULT."

TO SECURE OUR HEADLINERS ON X250 ARE ONE USE ONLY. (PLEASE VIEW ATTACHMENT). WHEN REMOVING THE HEADLINER THE CLIP MECHANISM WILL BECOME DAMAGED AND THE HEADLINER WILL NOT WILL NOT BE SECURE."

CAUSE: FSJB / RSJBS ARE RETURNED BACK TO THE SUPPLIER FOR TESTING WITH NO FAULTS EVIDENT. THE SYSTEM COMPLEXITY REQUIRES ALL MODULES TO BE RESTORED TO A DEFAULT STATE WITH REGARDS TO SHORT TERM MEMORY RETENTION OF SETTINGS AND DATA."

CAUSE: FSJB / RSJBS ARE RETURNED BACK TO THE SUPPLIER FOR TESTING WITH NO FAULTS EVIDENT. THE SYSTEM COMPLEXITY REQUIRES ALL MODULES TO BE RESTORED TO A DEFAULT STATE WITH REGARDS TO SHORT TERM MEMORY RETENTION OF SETTINGS AND DATA."

CAUSE THE FRONT CONTROL DISPLAY INTERFACE MODULE (TOUCHSCREEN) HAS NO EFFECT ON BLUETOOTH CONNECTIVITY IN THE CAR AND AS SUCH MAY BE INCORRECTLY DIAGNOSED AND REPLACED AS THE SOURCE OF THE ISSUE."

THE FUEL SENDERS ARE OPEN CIRCUIT. THIS DIAGNOSIS MAY BE INCORRECT DEPENDING ON THE MULTIMETER SETTINGS SELECTED BY THE TECHNICIAN DURING MEASUREMENT. CAUSE: THE MULTI METER RANGE MAYBE SET AT 'AUTO' AND DURING A SWEEP OF THE SENDER FROM 50OHMS TO 998OHMS THE MULTI METER HAS TO CHANGE ITS MEASUREMENT RANGE. FOR APPROXIMATELY 1 SECOND, DURING THE RANGE SWITCH OVER POINT, THE MULTI METER DISPLAY INDICATES AN OPEN CIRCUIT. THIS IS INCORRECTLY BEING DIAGNOSED AS A SENDER FAULT"

CAUSE: THIS MAY BE CAUSED BY ELECTRICAL INPUTS FROM THE VEHICLE SYSTEM."

THE INSTRUMENT PACK WILL SHOW A YELLOW WARNING TRIANGLE AND THE MESSAGE ""RADAR SENSOR BLOCKED ALSO ON INTERROGATION OF THE MODULE THE FOLLOWING CODE WOULD BE LOGGED C1A67-97, FORWARD LOOKING SENSOR OBSTRUCTED OR BLOCKED. CAUSE THE RADAR IS LOCATED BELOW THE FRONT NUMBER PLATE PLINTH ON THIS MODEL. IF THE INCORRECT SIZE NUMBER PLATE OR MULTIPLE NUMBER PLATES ARE FITTED THIS CAN OBSTRUCT THE RADAR."

DISPLAY FRONT (HLDF) ON OCCASIONS MAY FAIL TO DOWNLOAD SOFTWARE CORRECTLY FROM SDD RESULTING IN NO COMMUNICATIONS WITH THE MODULE AND BLANK SCREEN. CAUSE THIS MAY BE AS A RESULT OF LOW BATTERY VOLTAGE OR A BREAK IN CONTINUITY OF DIAGNOSTIC CONNECTION DURING THE DOWNLOAD."

CAUSE: THIS MAY BE CAUSED BY ELECTRICAL INPUTS FROM THE VEHICLE SYSTEM."

EARTH CABLE FROM THE VEHICLE BATTERY TO THE BODY AT LOCATION G4D178 CAN WORK LOOSE DUE TO THE FITTING AND REMOVAL OF THE NEGATIVE BATTERY CLAMP.."

CAUSE ALTERNATORS ARE BEING DAMAGED DUE TO CROSS POLARITY WHEN THE VEHICLE IS JUMP STARTED."

CAUSE:- THE DRIVERS AIRBAG CIRCUIT HAS BEEN INCORRECTLY DIAGNOSED AS BEING AT FAULT OR HAS MORE THAN ONE FAULT PRESENT."

CARRYING OUT PDIS AND THEN RETURNING THE VEHICLE TO A STORAGE COMPOUND WITHOUT REFITTING THE TRANSIT RELAY OR RETURNING THE VEHICLE TO TRANSIT MODE. TRANSIT MODE / TRANSIT RELAY ARE DESIGNED TO PROTECT THE CUSTOMERS BATTERY UP TO THE POINT OF DELIVERY. ALL VEHICLES IN STORAGE MUST HAVE THE TRANSIT RELAY IN PLACE OR BE IN TRANSIT MODE. ACTION: VEHICLES FITTED WITH A TRANSIT RELAY IF A NEW VEHICLE IS RETURNED TO A STORAGE COMPOUND FOLLOWING PDI THE TRANSIT RELAY MUST BE REFITTED TO THE VEHICLE. THE DEVICE MUST REMAIN ON THE VEHICLE UNTIL 72 HOURS PRIOR TO CUSTOMER DELIVERY. VEHICLES EQUIPPED WITH TRANSIT MODE. IF A NEW VEHICLE IS RETURNED TO A STORAGE COMPOUND FOLLOWING A PDI IT MUST BE RETURNED TO TRANSIT MODE. THE VEHICLE MUST REMAIN IN TRANSIT MODE UNTIL 72 HOURS PRIOR TO CUSTOMER DELIVERY."

HANDLE MAY 'STICK' IN THE OPEN POSITION; THE DOOR MAY NOT LATCH, AND; WITH THE IGNITION 'ON', THE 'DOOR OPEN' WARNING WILL BE ACTIVATED. CAUSE: THIS MAY BE CAUSED BY THE HANDLE BINDING BETWEEN THE BODY PANEL AND THE LOCK BARREL."

(TUNER IS STUCK IN AM BAND WHILE TOUCH SCREEN DISPLAYS FM1) CAUSE: NO ERROR HANDLING OF FREQUENCY BEING STORED IN HD RADIO MODULE."

AVAILABLE, IS NOT SHOWING AS PAIRED BUT IS AVAILABLE, IS DIFFICULT TO PAIR, AUDIO FRAGMENTS WHEN STREAMING MUSIC AND/OR OTHER UNEXPECTED BEHAVIOR. CAUSE: THIS CAN BE A RESULT OF REDUCED PHONE POWER DUE TO THE FOLLOWING:- BATTERY LIFE SOFTWARE UPDATE ON THE CUSTOMERS DEVICE, OTHER APPLICATIONS RUNNING IN THE BACKGROUND ON THE CUSTOMERS DEVICE (SUCH AS GAMES, SOCIAL MEDIA APPS, SEARCHING FOR NUMEROUS PAIRED DEVICES). A BREAK IN THE LINE OF SIGHT FROM THE IAM TO THE CUSTOMER DEVICE (E.G. DEVICE IN POCKET CAUSING ATTENUATION BY THE HUMAN BODY). ANOMALIES INTRODUCED WITH SOFTWARE UPDATES OF DEVICE THAT MAY REDUCE THE EFFECTIVENESS OF AUTHENTICATION BETWEEN THE CUSTOMER DEVICE AND THE VEHICLE. NOTE: THESE ISSUES ARE WELL DOCUMENTED ON OFFICIAL PHONE MANUFACTURERS SUPPORT WEB SITES."

IF BLOCKAGE OCCURS WHILE ACC IS BEING USED, DRIVER INTERVENE AND/OR ""RADAR SENSOR BLOCKED"" MESSAGE WILL APPEAR ON THE CLUSTER AND DTC C1A67-97 IS ALSO SET. BLOCKAGE CAN ALSO OCCUR WHEN ACC IS NOT BEING USED. CAUSE ""RADAR SENSOR BLOCKED"" INDICATES THAT THE ADAPTIVE SPEED CONTROL SYSTEM'S VISIBILITY HAS BEEN REDUCED DUE TO AN OBSTRUCTION. ACC CONTINUALLY SCANS FOR OBJECTS AHEAD AND, IF IT SEES NO OBJECTS I.E. VEHICLES, ROAD SIGNS, LAMPPOSTS, GUARD RAILS ETC, IT WILL INDICATE A BLOCKAGE EVEN IF THE ACC IS NOT USED. THE C1A67-97 DTC FLAGS A RADAR BLOCKAGE SITUATION AND NOT A SYSTEM FAULT."

CAUSE: THIS MAY BE CAUSED BY ELECTRICAL INPUTS FROM THE VEHICLE SYSTEM."

AFTER OPENING, EITHER FRONT DOOR, WITH THE EXTERIOR HANDLE, THE FOLLOWING MAY OCCUR: THE EXTERIOR DOOR HANDLE MAY STICK IN THE OPEN POSITION; DOOR MAY NOT LATCH, AND; WITH IGNITION ON, THE DOOR OPEN WARNING MAY BE ACTIVATED. *JS UPDATED 11/21/14. *PE

*RM

WIPER OPERATION MAY ALSO BE LOST FROM A BLOWN FUSE DUE TO A HEAVY LOAD SUCH AS SNOW. *RM

WIPER CAN NOT BE TURNED OFF WHILE THE IGNITION IS ON. A 20 AMP FUSE HAS BEEN FITTED INSTEAD OF A 30 AMP FUSE IN THE WINDSHIELD WIPER CIRCUIT. *PE

CAUSE: THIS MAY BE CAUSED BY THE ALUMINUM SURFACE BEING AFFECTED BY CLIMATIC CONDITIONS. ACTION: SHOULD A CUSTOMER EXPRESS THIS CONCERN, FOLLOW THE SERVICE INSTRUCTION OUTLINED BELOW."

THIS IS SEEN AS A LARGE GAP BETWEEN BUMPER AND HEADLAMP. CAUSE: PRODUCTION STANDARDS INADEQUATE."

CAUSE: THIS MAY BE CAUSED BY THE FRONT DOOR FINISHER MOVING REARWARDS ON THE DOOR."

CAUSE: THIS MAY BE CAUSED BY THE ALUMINUM SURFACE BEING AFFECTED BY CLIMATIC CONDITIONS."

OPERATION HAS BEEN OMITTED WHICH MAY RESULT IN WATER INGRESS ON SOME VEHICLES, HOWEVER THE PRIMARY DESIGN INTENT PREVENTION IS 100% ROBUST."

PARTIAL DELAMINATION AT THE BASE OF THE REAR DOOR 'B' POST. (PLEASE VIEW ATTACHMENT EXAMPLE) CAUSE:- EXCESS APPLIED TORQUE DURING PROFILING CAN CAUSE THE FIXING SCREW TO PROTRUDE THROUGH THE MOULDING INTO THE ADHESIVE STRIP. OVER TIME, THIS CAN WEAKEN THE ADHESIVE CREATING THE PARTIAL DELAMINATION."

ISSUE: RUST SPOTS MAY BE NOTICED ON THE REAR BUMPER. CAUSE: PARTICLES OF METAL REMAINING FROM BOOT SEAL MANUFACTURING PROCESS, EXITING THE BOOT APERTURE SEAL."

ISSUE: RUST SPOTS MAY BE NOTICED ON THE REAR BUMPER. CAUSE: PARTICLES OF METAL REMAINING FROM BOOT SEAL MANUFACTURING PROCESS, EXITING THE BOOT APERTURE SEAL."

COMPARISON WITH A VEHICLE IN SHOWROOM / WORKSHOP CONDITIONS STORED AT HIGHER TEMPERATURES WILL ALSO INDICATE THIS. CAUSE: THE XF VEHICLE HAS A 'LIFT ASSIST' SYSTEM, AND ITS OPERATION IS DEPENDENT ON TEMPERATURE,THE LOWER THE TEMPERATURE THE MORE LIKELY THE BOOT / TRUNK LID WILL NOT SELF-OPEN. THE SYSTEM WILL ALWAYS HAVE ENOUGH PRESSURE TO SUPPORT THE BOOT / TRUNK LID, ONCE FULLY OPENED."

CAUSE: THIS MAY BE CAUSED BY TORQUE RELAXATION OF THE ROOF OPENING PANEL FIXING SCREWS.

CAUSE: INCORRECT DRUM WHEEL RADIUS"

CAUSE: A LOWER-LEVEL SERVICE REPAIR PART TO BE USED IN THE EVENT A FRONT SUN VISOR VANITY MIRROR REQUIRES REPLACEMENT."

CAUSE: THIS MAY BE CAUSED BY THE MARGIN SEAL MOVING ON THE EXTRUSION AND TACKING AGAINST THE DOOR APERTURE."

THIS IS SEEN AS A LARGE GAP BETWEEN BUMPER AND HEADLAMP. CAUSE: PRODUCTION STANDARDS INADEQUATE."

CAUSE: THIS MAY BE CAUSED BY THE FRONT DOOR FINISHER MOVING REARWARDS ON THE DOOR."

*PE

*PE

*PE

THE EMITTING DIODE (LED) WITHIN THE LEFT-HAND (LH) AND RIGHT-HAND (RH) REAR LAMP ASSEMBLES MAY FAIL DUE TO CORROSION OF THE SILVER LEAD FRAME. *JS

THE LIGHT EMITTING DIODE (LED) WITHIN THE LEFT-HAND (LH) REAR LAMP ASSEMBLY MAY FAIL DUE TO CORROSION OF THE SILVER LEAD FRAME. *JS UPDATED 10/3/12. MODELS 2009-10 XF (X250). *PE

THE LIGHT EMITTING DIODE (LED) WITHIN THE RIGHT-HAND (RH) REAR LAMP ASSEMBLY MAY FAIL DUE TO CORROSION OF THE SILVER LEAD FRAME. *JS

BUBBLING ALONG THE TOP OR SIDE EDGES. THIS MAY BE CAUSED BY POOR ADHESION OF THE GLASS LAMINATES. *JS

*PE

*RM

designed.

to respond or no functionality at all.

CAUSE: INCORRECT DIAGNOSIS."

(SEE ATTACHED FILES FOR CLARIFICATION OF WHICH WARNING SYMBOL IS MEANT) CAUSE: THIS IS INTENTIONAL AND IS TO INFORM THE DRIVER THAT THERE IS A WARNING MESSAGE FOR THEIR ATTENTION AND THE MESSAGE IS DISPLAYED IN THE CLUSTER."

NIGHT TIME MODE SWITCHING OF SATELLITE NAVIGATION DOES NOT FUNCTION CORRECTLY. CAUSE:- THE FUNCTIONALITY OF THE INSTRUMENT ILLUMINATION SYSTEM AND DAY NIGHT MODE SWITCHING IS NOT FULLY UNDERSTOOD."

THE CUSTOMER MAY REPORT A RANGE OF PROBLEMS WITH THEIR PHONE CONNECTION, AUDIO QUALITY OR PHONEBOOK WHICH HAVE STARTED TO HAPPEN AFTER THE PHONE WAS MANUALLY OR AUTOMATICALLY SOFTWARE UPDATED. THE CUSTOMER MAY NOT BE AWARE OF AN AUTOMATIC UPDATE SO THIS SSM IS RECOMMENDED ON ANY BLUETOOTH PHONE ISSUES EXPERIENCED. CAUSE: PHONE SOFTWARE IS BEYOND THE CONTROL OF JAGUAR LAND ROVER AND ITS COMPATIBILITY WITH OUR SYSTEMS CAN ONLY BE TESTED AND APPROVED / DISAPPROVED ONCE RELEASED BY THE PHONE COMPANY. PHONES CAN SWITCH FROM WORKING WELL TO EXTREMELY POOR PERFORMANCE OR VICE VERSA AFTER AN UPDATE."

CAUSE: INCORRECT DIAGNOSIS."

MODELS X250/SF. NO MODEL YEARS LISTED. *PE

CONTROL SWITCH UNIT(S) FAILS TO RISE OR INITIALLY RISES BEFORE LOWERING ITSELF BACK TO ITS DEFAULT POSITION FOR AN IGNITION OFF STATE, WHICH IS CONFIRMED BY DTC P176B - 71 (TRANSMISSION RANGE SELECTOR UP AND DOWN POSITION CONTROL ERROR) CAUSE: POTENTIAL OF A MIXED STOCK CONDITION"

CONTROL SWITCH UNIT(S) FAILS TO RISE OR INITIALLY RISES BEFORE LOWERING ITSELF BACK TO ITS DEFAULT POSITION FOR AN IGNITION OFF STATE, WHICH IS CONFIRMED BY DTC P176B - 71 (TRANSMISSION RANGE SELECTOR UP AND DOWN POSITION CONTROL ERROR) CAUSE: POTENTIAL OF A MIXED STOCK CONDITION"

P0729 TO P0735, P0783, AND P2702 TO P2704 ARE STORED IN THE TRANSMISSION CONTROL MODULE (TCM). CAUSE: THIS MAY BE CAUSED BY DEGRADATION AND FAILURE OF THE LEAD-FREE BUSH CAUSING TRANSMISSION DEGRADATION AND FAILURE."

CAUSE: AN ERROR IN THE SOFTWARE FUNCTIONALITY HAS BEEN DISCOVERED WHICH CAN CREATE DTC P0780-94."

MODELS 2009-2013 XF, XJ RANGE, XK RANGE. *PE

CONTROL SWITCH FOR TRANSMISSION STICKS IN GEAR. *PE

*PE

A LIMITED NUMBER OF VEHICLES MAY HAVE BEEN MANUFACTURED AWAY FROM PROCESS AND IN SOME CASES THE DRIVER IS UNABLE TO ROTATE THE TRANSMISSION CONTROL SWITCH (TCS) AND IS UNABLE TO SELECT A DIFFERENT GEAR (PRND). *PE

instrument cluster.

IPK (INSTRUMENT PACK), FOLLOWING INVESTIGATION WI TH SDD THE FOL LOWING DTC P1571-64 (BRAKE SWI TCH - SIGNAL PLAUSIBILITY) IS STORED. CAUSE: A COMMUNICAT IONS ISSUE BETWEEN THE POWER T RAIN CONT ROL MODULE AND THE PARKBRAKE MODULE."

SPECIFICALLY RELATED TO FRONT BRAKE DISC GROOVING CAUSING A NOISE AND /OR JUDDER ISSUE. CAUSE: UNDER INVESTIGATION"

CAUSE: JAGUAR HAS RECEIVED WARRANTY CLAIMS FOR REAR SHOCK ABSORBER REPLACEMENT DUE TO NOISE. INVESTIGATION HAS REVEALED NO FAULT FOUND WITH THE SHOCK ABSORBER, AND MAY BE CAUSED BY OTHER COMPONENTS ON THE VEHICLE."

SPECIFICALLY RELATED TO FRONT BRAKE DISC GROOVING CAUSING A NOISE AND /OR JUDDER ISSUE. CAUSE: UNDER INVESTIGATION"

SPECIFICALLY RELATED TO FRONT BRAKE DISC GROOVING CAUSING A NOISE AND /OR JUDDER ISSUE. CAUSE: UNDER INVESTIGATION"

IPK (INSTRUMENT PACK), FOLLOWING INVESTIGATION WI TH SDD THE FOL LOWING DTC P1571-64 (BRAKE SWI TCH - SIGNAL PLAUSIBILITY) IS STORED. CAUSE: A COMMUNICAT IONS ISSUE BETWEEN THE POWER T RAIN CONT ROL MODULE AND THE PARKBRAKE MODULE."

THIS VERSION HAS BEEN ISSUED TO INCLUDE THE SPORTS BRAKE, AND PART NUMBER CHANGE. CAUSE: MARGIN SEAL MOVING ON THE EXTRUSION AND TACKING AGAINST THE DOOR APERTURE."

MODELS 2009-2010 XF, XK. *PE

MODELS XF/X250, XK/150. NO MODEL YEARS LISTED. *PE

*RM UPDATED 10/17/14. *PE

DUE TO A CHANGE IN DESIGN, THE REAR DIFFERENTIAL HAS A NEW SERVICE PART. AS A RESULT, SHOULD THE REAR DIFFERENTIAL REQUIRE REPLACEMENT IT WILL BE NECESSARY TO CONVERT THE DRIVELINE SYSTEM TO USE THE NEW DIFFERENTIAL. *PE UPDATED 11/7/11. *PE

A NUMBER OF REAR DIFFERENTIALS HAVE BEEN INCORRECTLY SUPPLIED WHICH MAY LEAD TO PREMATURE WEAR OF THE DIFFERENTIAL PINION HEAD AND TAIL CARRIER BEARINGS. *PE

PIPE, PARTIALLY, AFTER FALLING DOWN, AND THIS RESTRICTS FLOW OF FUEL TO TANK. MODEL XF, XJ. NO MODEL YEARS LISTED. *PE

FUEL FILLER DOOR HINGE ARMS MANUFACTURED AWAY FROM PROCESS. *PE

CAUSE: WHEN THE INSTRUMENT PANEL CLUSTER SOFTWARE IS UPDATED, THE STEERING COLUMN CALIBRATION WILL REVERT TO IT'S DEFAULT VALUES. THIS WILL RESULT IN NO STEERING COLUMN MOVEMENT."

SPOTS ON THE ROLLING SURFACE OF THE TIRE. CAUSE: TEMPORARY FLAT SPOTS NATURALLY DEVELOP ON THE ROLLING SURFACE OF A TIRE WHEN THE WHEELS OF THE VEHICLE ARE STATIONARY OVER A PERIOD OF TIME."

ACTION: WHEN DIAGNOSING CUSTOMER CONCERNS RELATING TO THE HYDRAULIC POWER STEERING SYSTEM, REFER TO THE SERVICE INFORMATION BELOW."

CAUSE: UNDER INVESTIGATION"

FLAT SPOTS ON THE ROLLING SURFACE OF THE TIRE. CAUSE: TEMPORARY FLAT SPOTS NATURALLY DEVELOP ON THE ROLLING SURFACE OF A TIRE WHEN THE WHEELS OF THE VEHICLE ARE STATIONARY OVER A PERIOD OF TIME."

FLAT SPOTS ON THE ROLLING SURFACE OF THE TIRE. CAUSE: TEMPORARY FLAT SPOTS NATURALLY DEVELOP ON THE ROLLING SURFACE OF A TIRE WHEN THE WHEELS OF THE VEHICLE ARE STATIONARY OVER A PERIOD OF TIME.

CAUSE: THIS MAY BE CAUSED BY A ROAD WHEEL/TIRE ASSEMBLY IMBALANCE AND/OR TEMPORARY TIRE FLAT-SPOTTING.

*RM

FAILURE SENSING ARE NOT COMPATIBLE WITH TRAILER LIGHT BOARDS THAT HAVE LED BASED ILLUMINATION. AS A RESULT OF THIS THE LED LIGHTING ON THE TRAILER BOARD MAY FLICKER DURING THE SENSING FUNCTION. (THIS ISSUES WILL ALSO PRESENT ITSELF IF FITTING LED REAR LIGHT CLUSTERS AVAILABLE IN THE AFTERMARKET(NON-JAGUAR APPROVED ACCESSORY) BASED UPON THIS WE RECOMMEND THAT TRAILER LIGHT BOARDS WITH STANDARD INCANDESCENT BULBS ONLY ARE FITTED."

CAUSE: CONDENSATION OR 'MISTING' ON THE INSIDE SURFACE OF THE HEADLAMP LENS MAY BE CAUSED BY NATURAL CONDENSATION THAT CAN BE EXPECTED UNDER CERTAIN ATMOSPHERIC CONDITIONS. CERTAIN LEVELS OF CONDENSATION ARE DEEMED ACCEPTABLE BY JAGUAR."

*JS

SEE ATTACHMENT SHOWING SWITCH PACK. CAUSE SWITCH PACKS ARE BEING INCORRECTLY REJECTED FOR STICKING SWITCHES , THE ACTUAL ROOT CAUSE FOR THE DEFECT IS DUE TO A TOLERANCE STACK UP ON THE FASCIA APERTURE RESULTING IN UNDUE PRESSURE BEING APPLIED TO THE SWITCHES."

SEE ATTACHMENT SHOWING SWITCH PACK. CAUSE SWITCH PACKS ARE BEING INCORRECTLY REJECTED FOR STICKING SWITCHES , THE ACTUAL ROOT CAUSE FOR THE DEFECT IS DUE TO A TOLERANCE STACK UP ON THE FASCIA APERTURE RESULTING IN UNDUE PRESSURE BEING APPLIED TO THE SWITCHES. THIS IS RECTIFIED FROM VIN NUMBER S48550."

CAUSE: A LOWER-LEVEL SERVICE REPAIR PART IS NOW AVAILABLE IN THE EVENT DAMAGE OR MARKING IS CAUSED BY AN OBJECT IMPACTING AGAINST THE LENS AND/OR STAINING/DISCOLORATION CONTAMINATION CAUSED BY USING ANY TYPE OF CLEANING PRODUCT ON THE LENS."

CAUSE: JAGUAR ARE RECEIVING A GROWING NUMBER OF REPORTED CONCERNS FROM XF CUSTOMERS RELATING TO THE OPERATION OF FRONT AND REAR SEAT BELTS, MANY OF THESE REPORTED CONCERNS HAVE BEEN INDUCED BY THE CUSTOMER OR SIMPLY BY THE CUSTOMER NOT UNDERSTANDING HOW THE FRONT AND REAR SEAT BELTS OPERATE. THESE CONCERNS REFER TO THE BELTS STICKING OR SEIZING IN OPERATION (ALR SYSTEM ACTIVE) TWISTED WEBBING AND SLOW RETRACTION."

THE CORRECT FUNCTION IS FOR THE TRUNK LID TO BE RELEASED FROM THE LATCH AND NOT TO RISE TO ITS FULLY OPEN POSITION. CAUSE: IN WARM INTERNAL OR EXTERNAL TEMPERATURES EXPANSION OF GAS AND FLUID IN THE STRUT MAY CAUSE THE TRUNK TO OPEN TO ITS FULL EXTENT. THE XF VEHICLE IS DESIGNED WITH A 'LIFT ASSIST' AND POWER CLOSE SYSTEM. THIS IS NOT AN ERROR CONDITION AND IS LESS LIKELY ON VERSIONS WITH A TRUNK SPOILER WHERE ONLY ONE STRUT IS USED. THE SYSTEM WILL ALWAYS HAVE ENOUGH PRESSURE TO SUPPORT THE BOOT / TRUNK LID, ONCE FULLY OPENED."

DA J2534 SOFTWARE DRIVER LEVEL V4.0 (MUST BE UPDATED TO THIS LEVEL ON ALL SDD MACHINES THAT USE THIS DEVICE) DA APP HUB LEVEL V2.4.0 (MUST BE UPDATED TO THIS LEVEL ON ALL SDD MACHINES THAT USE THIS DEVICE) DA FIRMWARE LEVEL V57. (ONLY NEEDS TO BE UPDATED ONCE TO EACH DEVICE, BECAUSE THIS IS HELD ON THE DEVICE ITSELF)"