2000 Isuzu Rodeo TSBs

BECAUSE AN ACCELERATOR POSITION SENSOR (APS) DIAGNOSTIC TROUBLE CODE P1271, P1273, P1275, P1280, OR P1285 IS SET. *TT

*TT

*TT

MAY CAUSE THE MALFUNCTION INDICATOR LAMP TO COME ON AND SET THE P0300 ENGINE MISFIRE CODE. *TT

*TT

*TT

WITH DIRECT ATTACK DOHC 3.2L / 3.5L V6 ENGINE. IN THE EVENT THAT CAMSHAFT TIMING HAS BEEN DISRUPTED, DUE TO TIMING BELT BREAKAGE OR CAMSHAFTS / CRANKSHAFT BEING ROTATED WITHOUT A TIMING BELT, THIS IS IMPORTANT PRIOR TO TIMING BELT INSTALLATION. *TT

AMERICAN ISUZU MOTORS DOES NOT SELL REMOTE STARTER KITS AND DOES NOT RECOMMEND ANY PARTICULAR INSTALLATION. *TT

*TT

*TT

*TT

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

*TT

*JG

*TT

THERE ARE NEWLY DESIGNED RUNNING BOARDS FOR MODELYEAR 2000 VEHICLES. *TT

If a Threebond product is unavailable, we recommend that you utilize the chart below to find equivalent of similar products (when available) from Loctite and Permatex.

connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.

*TT

THE MALFUNCTION INDICATOR LIGHT WILL ONLY SET AFTER THE FAULT HAS BEEN DETECTED FOR TWO CONSECUTIVE KEY CYCLES. *TT

*TT

*TT

Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.

parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.

certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.

TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.

*JG

(ICTA) is providing the following procedural recommendations to improve dealer efficiency when submitting Parts Warranty claims. We strongly recommend dealers follow these procedures in order to avoid delays in Parts Warranty claim payments and/or claim chargeback. This bulletin was revised to add a Parts Warranty Form

(ICTA) is providing the following procedural recommendations to improve dealer efficiency when submitting Parts Warranty claims. We strongly recommend dealers follow these procedures in order to avoid delays in Parts Warranty claim payments and/or claim chargeback.

Isuzu dealer technicians repairing Isuzu vehicles in and out of vehicle warranty. A TAC case number will be issued solely for information tracking purposes and future contact reference.

Spin-On Oil Filters.

The Exchange Program must be used when any Alpine radio or other component covered by this bulletin is repaired under warranty and may also be used for radio and component repairs not covered under warranty. Contact Alpine directly for pricing and payment methods applicable to radio and component repairs not covered under warranty.

While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

*JG

*TT

*TT

*TT

Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.

*TT 2002-2004 ISUZU AXIOM (UP), 198-2004 RODEO (UE) AND 1998-2004 RODEO SPORT. UPDATE *SC

*TT

REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. TECHNICIAN WILL NEED TO DETERMINE WHAT TYPE OF CALL THE CUSTOMER IS HAVING THAT IS UNWANTED. THE VEHICLE MAY RECEIVE AN INCOMING CALL JUST LIKE ANY OTHER PHONE. TYPICALLY THE CUSTOMER WILL HEAR THE PHONE RINGING IN THE VEHICLE. THIS SCENARIO ALSO INCLUDES INCOMING BLUETOOTH CALLS. ONE TYPE OF UNWANTED CALL CAN BE MADE IF THE KEY PAD IS FAULTY THE ONSTAR SYSTEM WILL TRY TO MAKE A BLUE BUTTON CALL FOR SHORTED VOLTAGE IN THE CIRCUITS. THE ONSTAR MODULE COULD HAVE AN INTERNAL FAULT AND PRODUCE A PHONE UNAVAILABLE AUDIO MESSAGE ALSO IT MAY HAVE A DIAGNOSTIC TROUBLE CODE U1500 OR B1000. REFER TO DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODE MAKING SURE TO FOLLOW ANY APPLICABLE BULLETINS OR PRELIMINARY INFORMATION SHEETS. A GREADYH OR GONSTAR READYH AUDIO MESSAGE HEARD WHILE DRIVING. IN SOME CASES IT HAS BEEN FOUND THAT THE CUSTOMER IS INADVERTENTLY PRESSING THE PUSH TO TALK BUTTON ON THE STEERING WHEEL CONTROLS. ON RARE OCCASIONS, OTHER ISSUES IN THE STEERING COLUMN OR STEERING WHEEL CONTROL SYSTEM MAY INDUCE THIS CONCERN.

*TT

*TT

*TT

*TT

For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

using the evaporative emission cart smoke machine and ultrasonic leak detectortools.

*EH

MAY EXHIBIT A STEERING WHEEL VIBRATION / SHIMMY (NIBBLE) OR BODY VIBRATION THROUGH THE STEERING WHEEL OR FLOORBOARD RESPECTIVELY ON SMOOTH ROAD SURFACE. *TT

*TT

*TT

MOUNTING SURFACE ON CERTAIN REAR SUSPENSION COMPONENTS MAY CAUSE CERTAIN BOLTS AND NUTS TO LOOSEN. *TT

Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.