2018 International Workstar TSBs
190 Technical Service Bulletins across 16 categories
Categories
Engine
59 bulletinsThis document aims to enable technicians to: 1.
Read full bulletin
Accurately identify third generation MaxxForce medium duty engine control systems. 2. Understand the programming intricacies related to these systems. 3. Autonomously execute programming tasks without needing technical support.
This article only applies to Models w/ 0016UZL Built Between 06/23/2014 05/11/2020 OR Models w/ 0016UZL w/ Safety...
Read full bulletin
Recall 14516 Completed Reference the appropriate Technician Manual for models outside of this population. Safety Recall 14516 has been issued for units built before June 23, 2014. For LT and 2018+ LoneStar: If there is a complaint of the bunk blower turning off after an auto start event, the BCM needs to be updated to Data Version 323 or higher. The bunk blower turning off was only present in BCM Data Version 309 to Data Version 322 To properly diagnose the system, you must ensure the recall has been performed. Only the "Cold Loop" sealed refrigerant core PN # 2614669C1 is to be replaced when the refrigerant circuit fails. DO NOT REPLACE THE COMPLETE UNIT IF THE A/C IS NOT FUNCTIONING. Complete unit is not Warrantable Refer to the BASIC TROUBLESHOOTING below before replacing any components. This will help you identify which component is at fault or any electrical issues. Refer to PARTS INFORMATION to properly identify the parts that may require replacement The A/C portion of the system is listed below in the parts section. The 16UZL No-Idle HVAC system is designed to disengage when the engine is started, and can be turned on with the key in any position. This battery-powered no-idle HVAC system provides heating and cooling of the sleeper area without use of the vehicle engine. The system is comprised of the no-idle HVAC components located in the sleeper HVAC module, a separate fuel-operated coolant heater mounted under the sleeper, and four additional batteries housed in a second battery box. The no-idle HVAC system shares the air handling assembly and several major components with the truck's standard HVAC system. Most importantly, the shared evaporator core contains refrigerant circuits for both the no idle system and the truck's standard A/C system. With this configuration, some procedures required to service the no idle A/C system will require opening the refrigerant circuit of the truck's standard A/C system. Trucks equipped with the 16UZL No-Idle HVAC system have two separate HVAC systems (Standard Truck A/C and the MaxxPower unit); it is important to identify each clearly, so you are troubleshooting the correct system. Per the Operator's Manual page 10: Run the heater at least once a month during the year (for a minimum of 15 minutes).
This article is intended to provide information for how to program International Engines that have been sold to another...
Read full bulletin
company and installed in a chassis that does NOT have an International VIN Number. This may include Detroit Series 40 engines, Perkins, Street Sweepers, Cranes, Fire Trucks, Generators, Blower motors, and more.
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature.
Read full bulletin
Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
New CARB Idle Reduction Change Request
Engine replacements for all International engines will need to follow this procedure.
In some geographic areas, ambient temperatures reaching below 15F (-10 C), including high levels of humidity, an...
Read full bulletin
operator may experience engine stalling, low performance, and or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists all the currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure Applies...
Read full bulletin
To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or...
Read full bulletin
Clean Idle Sticker, Clean Truck Check
Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or...
Read full bulletin
PSI engine.
Rebuilding Cylinder Heads on Certain MaxxForce 11/13, N13, and A26 engines; 2010 to present.
How to request a horsepower quote; all International and Cummins engines
Certain International N13 engines may be noncompliant to the required On Board Diagnostics (OBD) Monitor, Manufacturers...
Read full bulletin
Self-Test (MST) for over-boost, Exhaust Gas Recirculation (EGR) low flow, and EGR high flow monitors. Under certain conditions, this noncompliance may result in the failure to detect an increase in regulated air pollutants.
Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines
New air compressor incorporates an oil feed dowel O-ring.
Read full bulletin
Only models equipped with 2010 and newer MaxxForce 11/13 engines, all N13, and A26 engines
Per agreement with EPA and CARB, Cummins, Inc.
Read full bulletin
provided an emergency calibration for Cummins ISB, B6.7, ISL9, L9, and X15 engines when a DEF Quality Sensor (DQS) was not available. This action addressed the Diesel Exhaust Fluid (DEF) Quality Sensor failures in the field and the unavailability of parts due to the worldwide chip shortage. This recall is step two of this program designed to revert all affected vehicles back to the certified calibration and to provide them with the latest improved DQS and Coolant Control Valve (CCV) designs. Additionally, the emergency calibration and the restoration to the certified calibration with the latest improved DQS and Coolant Control Valve (CCV) designs have no effect on vehicle Emissions.
New Air compressor Incorporates an oil feed dowel O-ring; only models built with MaxxForce 11/13, N13, or A26 Engines
Rebuilding cylinder heads on certain EPA 2010 MaxxForce 11/13, N13, and A26 Engines
Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI...
Read full bulletin
engines or Cummins ISB engine with Allison transmissions
Rebuilding Cylinder Heads on Certain International MaxxForce 11/13 engines and all International N13 and A26 engines
QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
QLS Emergency Calibration.
Read full bulletin
applies to 2016 and newer Cummins B6.6, X15, and L9 engines and all A26 engines
High Pressure Fuel Pump external leaks from weep hole.
Read full bulletin
only trucks with 2010 MaxxForce 11/13L, all N13, or A26 engines
QLS Emergency Calibration; Models equipped with 2016 and newer Cummins B6.7, X15 and L9 engines or International A26...
Read full bulletin
engine.
QLS Emergency Calibration; Models with 2016 Cummins ISX, A26 and EPA 2017 and newer Cummins X15, L9, or B6.7 engines
Oil leaks at the Bottom of the Oil Filter Module; Only International A26, N13, or 2010 and newer 11 and 13 engines
Engine Oil Capacities.
Read full bulletin
All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
QLS Emergency Calibration.
Read full bulletin
Only models with EPA 2017 and newer Cummins X15, L9, or B6.7 engines
Snap-On torque wrench requirement for all big bore engine connecting rod bolt(s).
A26, N13, and 2010 EPA MaxxForce 11 and 13 engine Auxiliary Programable Parameters
On certain trucks equipped with an automatic transmission, if the automatic transmission is still in drive or reverse...
Read full bulletin
position and the stationary PTO switch is engaged, the engine RPM will ramp up and may overcome parking brake hold capability resulting in possible vehicle movement.
7095496C3 EGR Bellows Heat Shield ID; only models equipped with A26 Engine
Fuel Filters, Winter Additives, and Blending Fuels for Cummins Engines
This document will guide the user through the proper use of the A26 Misfire Detection Session to determine cylinder...
Read full bulletin
misfire count releted to the specific misfire DTCs.
WorkStar Hybrid Mount to Pad Mount A/C Compressor Retrofit; only models with Cummins ISB 6.7 engine.
On certain trucks equipped with an automatic transmission, if the automatic transmission is still in drive or reverse...
Read full bulletin
position and the stationary PTO switch is engaged, the engine rpm could ramp up and may overcome parking brake hold capability resulting in possible vehicle movement.
WorkStar Hybrid Mount to Pad Mount A/C Compressor Retrofit; only models with Cummins ISB 6.7 engine
Oil Capacities; All Electronic International Engines 1994 - Present.
Read full bulletin
Cummins ISB, ISM & ISX
Wabco OnGuard Software Update; Only 500k baud rate Units with Wabco OnGuard with Cummins Engines built before 9-24-2018.
Voltage gauge drops on cold engine start-up; Only models built with Cummins ISB, B6.7, ISL, or L9 engines
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction identification and proper diagnosis.
Read full bulletin
In addition, Diesel Exhaust Fluid (DEF) quality sensor monitors will be corrected to proper operating function.
ISB Starting System Diagnostics; Only models built with cummins ISB engines
A/C Compressor Radial mount failure; only models with Cummins ISB engine
Engine Oil Capacities All Electronic International Engines 1994 - Present.
Read full bulletin
Cummins ISB, ISM & ISX
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure; only Navistar...
Read full bulletin
Powered Trucks
Cummins Programming Guide and Cummins 285 Fault Code; Only pre-2007 models built with Cummins ISM Engine
The two-piece engine cover used on some WorkStar models is susceptible to road debris and moisture intrusion at the...
Read full bulletin
floorboard
AC Compressor Radial mount failure; Only models equipped with Cummins ISB engine
The recalibration will remove engine aftertreatment system faults during reset while ensuring required driver warning...
Read full bulletin
remains.
Urea Quality Sensor (UQS) Supplemental Diagnostic and Service Information; only models with SCR Aftertreatment system...
Read full bulletin
and N9, N10, N13, A26 or Cummins ISB, ISL, ISX engines built from January 2016
Loose or Missing Charge Air Cooler Clamps and Possible DPF Plugging; only models Equipped with Cummins B6.7 engine
Supplemental Fuel System Diagnostics - Racor Chassis Mounted Fuel Filter; only with Cummins L9 EPA 17 engine
Engine Oil Capacities
Engine software update to improve engine and aftertreatment warm up strategies.
Cummins Engine Remote Engine Speed Control; only with feature code12XAT or 12XBM
Certain DuraStar and WorkStar model trucks built with Cummins ISL engines and intended for stationary applications may...
Read full bulletin
not be equipped with the necessary fuel cooler.
Other
41 bulletinsThis document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes.
Read full bulletin
(Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
J1939 Data Link Source Address Information
Diagnosis of chassis wander complaints.
J1939 Data Link Source Address Information
J1939 Data Link Troubleshooting
Telematics installation guidelines - Only units with 500K data link
J1939 Data link source address information
Pico Scope CCOS (Crankcase Separator Test)
PicoScope Test One Channel RCT
PicoScope Test Resistance and Ohmmeter
PicoScope Test for Datalink (CAN) Health Shorts & opens
J1939 Data Link Source Address Information
J1939 Data Link Troubleshooting
How to obtain As built parameter list
Bendix Stability control - customer satisfaction performance improvement; Specific Emergency / Tanker applications only.
Cab Lean Concern
Driveline Information Center and Troubleshooting Procedures
Cleaning and Disinfecting Trucks and Buses
J1939 Data Link Troubleshooting
J1939 Data Link Source Address Information
SCR Vehicles Setting DEF Quality Faults due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
Only models built with Cummins X15; Fault Code 7125
Driveline Information Center and Troubleshooting Procedures
Programing New Key Fobs
The suspect population may have been built with a left-side radiator stay rod of insufficient length, resulting in...
Read full bulletin
reduced radiator to fan clearance.
Telematics Installation Guidelines; only Units with 500K Data Link
Trucks may have been built with incorrect huck bolt washers for the lift axle huck bolts resulting in loosened huck bolt...
Read full bulletin
fasteners
Telematics Installation Guidelines; Only units built with 500K baud rate data link
NEW Ultrasonic DEF Tank Sending Unit; only models with SCR Aftertreatment system.
J1939 Data Link Troubleshooting
SCR Vehicles Setting 3363-16 (FC1713) due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
Cooling System Flush Procedure
J1939 Data Link Source Address Information
J1939 Data Link Troubleshooting
Updating OnCommand Link with Accelerator
OnCommand EZ-Tech
Winter Front Usage
ISX, N13, and N9 / N10 Aftertreatment Private Data Link Troubleshooting
J1939 Data Link Troubleshooting
Electrical
19 bulletinsThis document provides: Steps to take when switch pack programming fails, or when switch pack disappears after body...
Read full bulletin
control module update Sample scenarios Additional information to assist readers in understanding DLB switch pack programming
This document details the procedure that must be followed to ensure proper alternator troubleshooting.
Cummins B6.7 Grid Heater Relay
General Wheel Speed Sensor Troubleshooting
PicoScope Wheel Speed Sensor Test
PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
PicoScope Test 12V Electrical Noise Detection
PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
Dual Drive Cab Throttle Position Harness for APS/IVS throttle pedals; only models with both left hand and right hand...
Read full bulletin
drive.
New or replacement body control Module (BC,BCM) not detected; Gen 4 BCM
General wheel speed sensor troubleshooting
Cummins B6.7 Grid Heater Relay
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
Tool Instruction - BCM Programming Harness
Body Builder Accessories Backfeeding Ignition Voltage
HVAC fault 2609-19 with 4th Gen BCM; Only models equipped with 4th generation BCM
Urea Quality Sensor (UQS) Boot Order
Urea Quality Sensor (UQS) Boot Order
Body & Paint
16 bulletinsThis article addresses chassis lean conditions on all chassis.
Read full bulletin
This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
Cab water leak trouble shooting tips
Cab water leak troubleshooting tips; HX with steel cab only
Cab water leak troubleshooting tips
Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
Day cab roof air deflector causing loud vibration noise at highway speed
Day Cab Roof Air Deflector Vibrates against Cab Roof; only models with P/N 4067947C92 Roof Air Deflector
Wind noise at upper side of cab door due to door out of alignment
Body Controller Updates for 500k Baud Data link
Cab Water Leak Troubleshooting Tips; Excluding 9000i, PayStar(HX), CityStar, or LoadStar
The First Check to make when Troubleshooting any Body Controller or ESC Issue
Wind noise at upper side of cab door
Body Controller Updates for 500k Baud data link
Vehicle Speed ( VSS ) Output for Bodybuilders
Hood Gap and Alignment Tolerances
Windshield Replacement on trucks equipped with Lane Departure Cameras; Only models with one of the following feature...
Read full bulletin
codes 008TTG, 0008TPU, 0008TTT, 0008TTU
Transmission
13 bulletinsTitle: Steering Gear Seal Repair Guidelines Applies To: Steering gears
Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
Power Distribution Center (PDC) Replacement; 7000 (Workstar) Model Series with Allison or Manual Transmissions
The vehicles in this FSC were involved in Safety Recall 18518 which has been completed on these vehicles.
Read full bulletin
The ECM needs to be reprogrammed to be compatible with the new transmission calibration that was previously programmed into the TECU.
International; HV, HX, LT, MV, RH, LS, ProStar, TranStar, WorkStar; It is possible for an internal clutch finger to fail...
Read full bulletin
after Safety Recall 18518 was completed. This campaign is only for this failure mode and these conditions. Clutches that are replaced under this field campaign but do not exhibit this type of failure will have the warranty claim charged back to the servicing location.
DUAL STEERING GEAR AIR BLEED PROCEDURE
Heavy Duty Clutch May Not Acheive Full Departure
ECA Clutch Departure
Eaton Bulletin for their ECA Clutch issue referenced from IK1100033 and IK1100034
An internal component within the clutch assembly may fail, which in special circumstances could inhibit clutch...
Read full bulletin
disengagement resulting in the transmission to not achieve neutral when commanded by the driver.
EATON ECA Clutches - Refer to CLIB0034
EATON ECA Clutches - EATON document referenced from IK1300170
Steering Noise in Vehicles Equipped with Dual Steer; Only models equipped with dual steering gear
Infotainment
8 bulletinsThis tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files.
Read full bulletin
It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
Radio Diagnostics and Information
NEW Ultrasonic DEF Head Unit; All SCR vehicles
NEW Ultrasonic DEF Head Unit available; Only models equipped with SCR Aftertreatment.
NEW Ultrasonic DEF Head Unit; Only vehicles Equipped with SCR
NEW Ultrasonic DEF Head Unit; only models equipped with SCR Aftertreatment
NEW Ultrasonic DEF Head Unit
Radio Diagnostics and Information
Brakes
7 bulletinsThis document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and...
Read full bulletin
windshields using an ultrasonic sound detector.
Bendix EC80 Blank Module Replacement Program; This document will guide the user through selecting the correct ABS module...
Read full bulletin
when it has been determined a replacement is needed. Only Models with EC-80 ABS Controller
WorkStar Hybrid Mount to Pad Mount A/C Compressor Retrofit
Brake pedal not returning and sticking slightly in the applied position
Brake pedal not returning and sticking slightly in the applied position
Brake Lights Staying On
Brake Lights Staying On
HVAC & Climate
5 bulletinsTitle: A/C Refrigerant and Oil Capacities Applies To: All current models
A/C Refrigerant and Oil Capacities
Air Pressure Gauges and A/C Pressure Transducer Troubleshooting
Air Pressure Gauges and A/C Pressure Transducer Troubleshooting
A/C Refrigerant and Oil Capacities
Tires & Wheels
5 bulletinsSuggested alignment target values when performing a vehicle axle alignment.
Suggested alignment target values when performing a vehicle axle alignment
Suggested alignment target values when performing a vehicle axle alignment
FLR-10 Bendix Wingman Misalignment Issues; only models with Feature Code 08TKY Wingman FLR-10 Radars
FLR-10 Bendix Wingman Misalignment Issues; only models with Feature Code 08TKY Wingman FLR-10 Radars
Software & Calibration
4 bulletinsQLS Emergency Calibration Revert Process
QLS Emergency Calibration Revert Process
Controller Updates for 500k Baud; only vehicles with 500k baud data link
Using Supplier Software to Check DTCs
Suspension
3 bulletinsThis document reminds technicians of the critical relationship between the truck's suspension and the driveline operating angles.
Read full bulletin
The information applies to diesel, gas, and electric vehicles.
Front cab mount bushings/insulators MV, HV, DuraStar, and WorkStar vehicles used in severe vocations
Suspension Lean Diagnostics; All models
Lighting
3 bulletinsRepair Procedures for Vehicles Struck by Lightning
Repair Information for Damaged Headlight Connector
Repair Information for Damaged Headlight Connector
Steering
3 bulletinsSteering Noise in Vehicles Equipped with Dual Steer
Steering Fluids
Steering Shake, Shimmy, Shudder, or Steering Vibration; only with 14k front weight rated axles and below
Pre-Delivery & Maintenance
2 bulletinsTitle: Service Portal iKNow Feedback Case Types Applies To: All
Frame Rail Straightness Inspection Procedure
Fuel System
1 bulletinCummins L9 EPA 17 Supplemental Fuel System Diagnostics - Racor Chassis Mounted Fuel Filter / Cummins fault 559
Air Bags & Safety
1 bulletinThe seat belt assemblies may not satisfy the requirements of FMVSS 210 / CMVSS 213.
Read full bulletin
In the event of a vehicle accident, there is an increased risk that the shoulder D-ring bolt for the driver and passenger seats may break.