2017 International Transtar TSBs
176 Technical Service Bulletins across 15 categories
Categories
Engine
45 bulletinsThis article only applies to Models w/ 0016UZL Built Between 06/23/2014 05/11/2020 OR Models w/ 0016UZL w/ Safety...
Read full bulletin
Recall 14516 Completed Reference the appropriate Technician Manual for models outside of this population. Safety Recall 14516 has been issued for units built before June 23, 2014. For LT and 2018+ LoneStar: If there is a complaint of the bunk blower turning off after an auto start event, the BCM needs to be updated to Data Version 323 or higher. The bunk blower turning off was only present in BCM Data Version 309 to Data Version 322 To properly diagnose the system, you must ensure the recall has been performed. Only the "Cold Loop" sealed refrigerant core PN # 2614669C1 is to be replaced when the refrigerant circuit fails. DO NOT REPLACE THE COMPLETE UNIT IF THE A/C IS NOT FUNCTIONING. Complete unit is not Warrantable Refer to the BASIC TROUBLESHOOTING below before replacing any components. This will help you identify which component is at fault or any electrical issues. Refer to PARTS INFORMATION to properly identify the parts that may require replacement The A/C portion of the system is listed below in the parts section. The 16UZL No-Idle HVAC system is designed to disengage when the engine is started, and can be turned on with the key in any position. This battery-powered no-idle HVAC system provides heating and cooling of the sleeper area without use of the vehicle engine. The system is comprised of the no-idle HVAC components located in the sleeper HVAC module, a separate fuel-operated coolant heater mounted under the sleeper, and four additional batteries housed in a second battery box. The no-idle HVAC system shares the air handling assembly and several major components with the truck's standard HVAC system. Most importantly, the shared evaporator core contains refrigerant circuits for both the no idle system and the truck's standard A/C system. With this configuration, some procedures required to service the no idle A/C system will require opening the refrigerant circuit of the truck's standard A/C system. Trucks equipped with the 16UZL No-Idle HVAC system have two separate HVAC systems (Standard Truck A/C and the MaxxPower unit); it is important to identify each clearly, so you are troubleshooting the correct system. Per the Operator's Manual page 10: Run the heater at least once a month during the year (for a minimum of 15 minutes).
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature.
Read full bulletin
Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
New CARB Idle Reduction Change Request
Engine replacements for all International engines will need to follow this procedure.
In some geographic areas, ambient temperatures reaching below 15F (-10 C), including high levels of humidity, an...
Read full bulletin
operator may experience engine stalling, low performance, and or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists all the currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure Applies...
Read full bulletin
To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or...
Read full bulletin
Clean Idle Sticker, Clean Truck Check
Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or...
Read full bulletin
PSI engine.
Rebuilding Cylinder Heads on Certain MaxxForce 11/13, N13, and A26 engines; 2010 to present.
How to request a horsepower quote; all International and Cummins engines
Certain International N13 engines may be noncompliant to the required On Board Diagnostics (OBD) Monitor, Manufacturers...
Read full bulletin
Self-Test (MST) for over-boost, Exhaust Gas Recirculation (EGR) low flow, and EGR high flow monitors. Under certain conditions, this noncompliance may result in the failure to detect an increase in regulated air pollutants.
Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines
New air compressor incorporates an oil feed dowel O-ring.
Read full bulletin
Only models equipped with 2010 and newer MaxxForce 11/13 engines, all N13, and A26 engines
New Air compressor Incorporates an oil feed dowel O-ring; only models built with MaxxForce 11/13, N13, or A26 Engines
Rebuilding cylinder heads on certain EPA 2010 MaxxForce 11/13, N13, and A26 Engines
Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI...
Read full bulletin
engines or Cummins ISB engine with Allison transmissions
Rebuilding Cylinder Heads on Certain International MaxxForce 11/13 engines and all International N13 and A26 engines
QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
QLS Emergency Calibration.
Read full bulletin
applies to 2016 and newer Cummins B6.6, X15, and L9 engines and all A26 engines
High Pressure Fuel Pump external leaks from weep hole.
Read full bulletin
only trucks with 2010 MaxxForce 11/13L, all N13, or A26 engines
QLS Emergency Calibration; Models with 2016 Cummins ISX, A26 and EPA 2017 and newer Cummins X15, L9, or B6.7 engines
Oil leaks at the Bottom of the Oil Filter Module; Only International A26, N13, or 2010 and newer 11 and 13 engines
Engine Oil Capacities.
Read full bulletin
All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
QLS Emergency Calibration.
Read full bulletin
Only models with EPA 2017 and newer Cummins X15, L9, or B6.7 engines
A26, N13, and 2010 EPA MaxxForce 11 and 13 engine Auxiliary Programable Parameters
7095496C3 EGR Bellows Heat Shield ID; only models equipped with A26 Engine
Fuel Filters, Winter Additives, and Blending Fuels for Cummins Engines
Oil Capacities; All Electronic International Engines 1994 - Present.
Read full bulletin
Cummins ISB, ISM & ISX
Wabco OnGuard Software Update; Only 500k baud rate Units with Wabco OnGuard with Cummins Engines built before 9-24-2018.
The height control valve lower bracket may fail due to fatigue and may result in incorrect ride height and possible...
Read full bulletin
driveline vibration.
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
ISB Starting System Diagnostics; Only models built with cummins ISB engines
Engine Oil Capacities All Electronic International Engines 1994 - Present.
Read full bulletin
Cummins ISB, ISM & ISX
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure; only Navistar...
Read full bulletin
Powered Trucks
Cummins Programming Guide and Cummins 285 Fault Code; Only pre-2007 models built with Cummins ISM Engine
Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction identification...
Read full bulletin
and proper diagnosis.
Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction identification...
Read full bulletin
and proper diagnosis.
Urea Quality Sensor (UQS) Supplemental Diagnostic and Service Information; only models with SCR Aftertreatment system...
Read full bulletin
and N9, N10, N13, A26 or Cummins ISB, ISL, ISX engines built from January 2016
The fire extinguishers may become clogged or require excessive force to activate.
Read full bulletin
In certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. Only equipped with Kidde model FC5 and FC10 fire extinguishers identified by International part numbers 1696423C2 and 1696423C3 and installed post production at Navistar?s Truck Sales Processing Center (TSPC).
Engine software On Board Diagnostic (OBD) issues will be corrected which will aid in engine malfunction identification...
Read full bulletin
and proper diagnosis; only with 2016 compliant N13 engines and 500K baud communications network.
Engine Oil Capacities
CPA Injector Misfire Detection; Only models with 2004 thru 2017 International engines.
Cylinder Performance Analyzer (CPA) Resource Center; Only models with 2004 thru 2017 International engines.
Other
45 bulletinsThis document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes.
Read full bulletin
(Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
J1939 Data Link Source Address Information
Diagnosis of chassis wander complaints.
J1939 Data Link Source Address Information
J1939 Data Link Troubleshooting
Telematics installation guidelines - Only units with 500K data link
J1939 Data link source address information
Pico Scope CCOS (Crankcase Separator Test)
PicoScope Test One Channel RCT
PicoScope Test Resistance and Ohmmeter
PicoScope Test for Datalink (CAN) Health Shorts & opens
J1939 Data Link Source Address Information
J1939 Data Link Troubleshooting
How to obtain As built parameter list
Cab Lean Concern
Driveline Information Center and Troubleshooting Procedures
Cleaning and Disinfecting Trucks and Buses
J1939 Data Link Troubleshooting
J1939 Data Link Source Address Information
SCR Vehicles Setting DEF Quality Faults due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
Only models built with Cummins X15; Fault Code 7125
Child Checkmate is not functioning correctly; Only buses with features 47EXC, 47EXD, 47EXE built from 4/18/16 to 5/15/17
Driveline Information Center and Troubleshooting Procedures
Child Checkmate is not functioning correctly; Only buses with features 47EXC, 47EXD, 47EXE built from 4/18/16 to 5/15/17
Hendrickson Assembly Instructions; Transverse Torque Rods
Programing New Key Fobs
Telematics Installation Guidelines; only Units with 500K Data Link
Telematics Installation Guidelines; Only units built with 500K baud rate data link
NEW Ultrasonic DEF Tank Sending Unit; only models with SCR Aftertreatment system.
J1939 Data Link Troubleshooting
SCR Vehicles Setting 3363-16 (FC1713) due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
Cooling System Flush Procedure
J1939 Data Link Source Address Information
J1939 Data Link Troubleshooting
Updating OnCommand Link with Accelerator
OnCommand EZ-Tech
Winter Front Usage
ISX, N13, and N9 / N10 Aftertreatment Private Data Link Troubleshooting
J1939 Data Link Troubleshooting
Telematic Installation Guidelines; only Units with 500K Data Link
OnCommand EZTech
OnCommand EZ-Tech Download Center
RADIATOR INTERNAL RESTRICTION AND FLUSH PROCEDURE
Body & Paint
17 bulletinsThis article addresses chassis lean conditions on all chassis.
Read full bulletin
This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
Cab water leak trouble shooting tips
Cab water leak troubleshooting tips; HX with steel cab only
Cab water leak troubleshooting tips
Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
Day cab roof air deflector causing loud vibration noise at highway speed
Wind noise at upper side of cab door due to door out of alignment
8600/TranStar Hood Latches Do Not Fit Correctly.
Read full bulletin
Only models that have had or will have the hood latches and/or the fender extensions replaced.
Body Controller Updates for 500k Baud Data link
Cab Water Leak Troubleshooting Tips; Excluding 9000i, PayStar(HX), CityStar, or LoadStar
The First Check to make when Troubleshooting any Body Controller or ESC Issue
Wind noise at upper side of cab door
Body Controller Updates for 500k Baud data link
Hood Latches Do Not Fit Correctly
MIRROR REPAIR PROCEDURES AND REPLACEMENT PARTS AVAILABILITY
BODY CONTROLLER UPDATES FOR ALL VEHICLES WITH 500K BAUD DATA LINK
BODY CONTROLLER UPDATES; ONLY WHEN EQUIPPED WITH 500K BAUD COMMUNICATION NETWORK
Electrical
17 bulletinsThis document covers battery diagnostics, maintenance and storage requirement.
General Wheel Speed Sensor Troubleshooting
PicoScope Wheel Speed Sensor Test
PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
PicoScope Test 12V Electrical Noise Detection
PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
New or replacement body control Module (BC,BCM) not detected; Gen 4 BCM
General wheel speed sensor troubleshooting
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
Tool Instruction - BCM Programming Harness
DM harness inspection; Only with Steering Column feature code 05710
HVAC fault 2609-19 with 4th Gen BCM; Only models equipped with 4th generation BCM
Urea Quality Sensor (UQS) Boot Order
The metallic battery box cover latch, when unlatched from its anchor may articulate and potentially contact the battery...
Read full bulletin
jump start stud and if the protective cover of the jump start stud is not in place resulting in an electrical short to ground.
Urea Quality Sensor (UQS) Boot Order
Air Conditioning Electrical Diagnostics
HVAC & Climate
10 bulletinsTitle: A/C Refrigerant and Oil Capacities Applies To: All current models
A/C Refrigerant and Oil Capacities
Air Pressure Gauges and A/C Pressure Transducer Troubleshooting
Air Pressure Gauges and A/C Pressure Transducer Troubleshooting
A/C Refrigerant and Oil Capacities
A/C Refrigerant and Oil Capacities
2010 and Newer Vehicle Air Conditioning Diagnostics (Start Here)
Air Conditioning Control Head Diagnostics
Air Conditioning Mechanical Pressures Diagnostics
2010 AND NEWER VEHICLE AIR CONDITIONING DIAGNOSTICS (START HERE)
Infotainment
8 bulletinsThis tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files.
Read full bulletin
It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
Radio Diagnostics and Information
NEW Ultrasonic DEF Head Unit; All SCR vehicles
NEW Ultrasonic DEF Head Unit available; Only models equipped with SCR Aftertreatment.
NEW Ultrasonic DEF Head Unit; Only vehicles Equipped with SCR
NEW Ultrasonic DEF Head Unit; only models equipped with SCR Aftertreatment
NEW Ultrasonic DEF Head Unit
Radio Diagnostics and Information
Tires & Wheels
7 bulletinsSuggested alignment target values when performing a vehicle axle alignment.
Suggested alignment target values when performing a vehicle axle alignment
Suggested alignment target values when performing a vehicle axle alignment
Bendix SmartWave SmarTire Pressure Maintenance System TPMS
FLR-10 Bendix Wingman Misalignment Issues; only models with Feature Code 08TKY Wingman FLR-10 Radars
FLR-10 Bendix Wingman Misalignment Issues; only models with Feature Code 08TKY Wingman FLR-10 Radars
Fifth Wheel Jaw Unlock; only models with Feature 595BAW or 597017 - electronic Jaw release
Lighting
6 bulletinsRepair Procedures for Vehicles Struck by Lightning
Repair Information for Damaged Headlight Connector
Repair Information for Damaged Headlight Connector
Repair Information for Damaged Headlight Connector
Repair Information for Damaged Headlight Connector
Trailer Auxiliary Switch Lamp Burning Out; Only Vehicles Equipped with Feature Code 0008TTH or 0008THG
Brakes
5 bulletinsThis document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and...
Read full bulletin
windshields using an ultrasonic sound detector.
Bendix EC80 Blank Module Replacement Program; This document will guide the user through selecting the correct ABS module...
Read full bulletin
when it has been determined a replacement is needed. Only Models with EC-80 ABS Controller
Brake pedal not returning and sticking slightly in the applied position
Brake pedal not returning and sticking slightly in the applied position
Brake Lights Staying On
Software & Calibration
4 bulletinsQLS Emergency Calibration Revert Process
Controller Updates for 500k Baud; only vehicles with 500k baud data link
Using Supplier Software to Check DTCs
Dealer EZ-Tech and Diagnostic Software Support Resource Center
Transmission
3 bulletinsTitle: Steering Gear Seal Repair Guidelines Applies To: Steering gears
Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
Tech Tip to aid technicians in the efficient removal and installation of a TC10 transmission
Suspension
3 bulletinsThis document reminds technicians of the critical relationship between the truck's suspension and the driveline operating angles.
Read full bulletin
The information applies to diesel, gas, and electric vehicles.
Suspension Lean Diagnostics; All models
Improved Bushings for Hendrickson Torque Rods
Pre-Delivery & Maintenance
2 bulletinsTitle: Service Portal iKNow Feedback Case Types Applies To: All
Frame Rail Straightness Inspection Procedure
Fuel System
2 bulletinsCummins L9 EPA 17 Supplemental Fuel System Diagnostics - Racor Chassis Mounted Fuel Filter / Cummins fault 559
Certain vehicles with Exempt Emissions Label.
Steering
2 bulletinsSteering Fluids
Steering Shake, Shimmy, Shudder, or Steering Vibration; only with 14k front weight rated axles and below