2024 International MV TSBs

exhibit a no-start condition, low power under increased fuel demand, an illuminated check engine light, or Cummins Fault Code 559. The condition may be caused by an excessively long fuel pickup tube contacting the bottom of the fuel tank and restricting fuel flow.

International vehicles built after 1/8/2018. International's Electrical Engineering Team made this change to improve the longevity of the OEM coatings and to improve applications at the factory.

Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.

Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.

may experience engine stalling, low performance, and/or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.

operator may experience engine stalling, low performance, and or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists all the currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.

To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check

Clean Idle Sticker, Clean Truck Check

LOCATION Mounted Inside Engine Compartment, Right Side

PSI engine.

engines or Cummins ISB engine with Allison transmissions

(Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)

In some cases, cable damage has been seen where the antenna cables pass over the mounting hardware. This cable damage can cause the fault codes listed below, intermittent operation of the predictive cruise control, and issues with OCC report uploading.

Content includes parts list, two new graphics, and 17 additional steps. DEFECT DESCRIPTION: Certain International MVTM Series trucks may have a driveshaft that is too short and may come out of the slip yoke.

fault codes after a vehicle sits for 2 or 3 days.

fault codes after a vehicle sits for 2 or 3 days.

Units built after November of 2024 as well as older units that were updated with DLB between 11/5/2024 and 6/26/2025 with Remote Power Modules (RPM) modules, can experience loss of RPM functionality as well as other electrical system concerns. Kernel 753 was released to DLB on 6/26/2025 to address these concerns.

control module update Sample scenarios Additional information to assist readers in understanding DLB switch pack programming

inputs from the driver or passenger. In some of these situations, it is possible for this symptom to be present without any fault codes becoming active. This article will guide the user through performing a hard reset of a door pod, which can restore the door pod to its operational condition, thereby avoiding the need for replacement. The steps in this article should be performed BEFORE diagnostics are completed for any active faults.

Some of the unused holes during the conversion may have hardware improperly installed.

This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.

This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean. If you are not able to come to a repair direction after completely following the article and filling out the form, please attach the form and requested photos to a case file for further assistance

look down mirrors.

It does not include any diagnostics for body leans, such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean.

The information applies to diesel, gas, and electric vehicles.

windshields using an ultrasonic sound detector.

This can affect all LT, RH, MV, HV models, 2021MY and up HX, 2024MY and up CE Bus with BCM kernel version 752, 753, and 754. Vehicles built or updated with DLB between 6/1/25 and 11/4/25 are suspected of having these kernels installed on the BCM. The most common complaint is that the steering wheel switches do not function, which, depending on the vehicle model and options, can cause the bus door, pupil warning lights, radio controls, marker interrupt, and cruise control to stop working. Other complaints can include short circuit faults from multiple sensor circuits attached to the BCM setting at the same time, the vehicle will not go into gear, the headlights are stuck on, the brake lights are stuck on, or the parking brake alarm is sounding (horn chirping) with the parking brake set. As of 11/4/25, these symptoms can be resolved by updating the BCM to kernel 755 or later with DLB.

16VVA,16VUZ, or 16VVM

It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.