2019 International MV TSBs
186 Technical Service Bulletins across 15 categories
Categories
Engine
40 bulletinsThis article only applies to Models w/ 0016UZL Built Between 06/23/2014 05/11/2020 OR Models w/ 0016UZL w/ Safety...
Read full bulletin
Recall 14516 Completed Reference the appropriate Technician Manual for models outside of this population. Safety Recall 14516 has been issued for units built before June 23, 2014. For LT and 2018+ LoneStar: If there is a complaint of the bunk blower turning off after an auto start event, the BCM needs to be updated to Data Version 323 or higher. The bunk blower turning off was only present in BCM Data Version 309 to Data Version 322 To properly diagnose the system, you must ensure the recall has been performed. Only the "Cold Loop" sealed refrigerant core PN # 2614669C1 is to be replaced when the refrigerant circuit fails. DO NOT REPLACE THE COMPLETE UNIT IF THE A/C IS NOT FUNCTIONING. Complete unit is not Warrantable Refer to the BASIC TROUBLESHOOTING below before replacing any components. This will help you identify which component is at fault or any electrical issues. Refer to PARTS INFORMATION to properly identify the parts that may require replacement The A/C portion of the system is listed below in the parts section. The 16UZL No-Idle HVAC system is designed to disengage when the engine is started, and can be turned on with the key in any position. This battery-powered no-idle HVAC system provides heating and cooling of the sleeper area without use of the vehicle engine. The system is comprised of the no-idle HVAC components located in the sleeper HVAC module, a separate fuel-operated coolant heater mounted under the sleeper, and four additional batteries housed in a second battery box. The no-idle HVAC system shares the air handling assembly and several major components with the truck's standard HVAC system. Most importantly, the shared evaporator core contains refrigerant circuits for both the no idle system and the truck's standard A/C system. With this configuration, some procedures required to service the no idle A/C system will require opening the refrigerant circuit of the truck's standard A/C system. Trucks equipped with the 16UZL No-Idle HVAC system have two separate HVAC systems (Standard Truck A/C and the MaxxPower unit); it is important to identify each clearly, so you are troubleshooting the correct system. Per the Operator's Manual page 10: Run the heater at least once a month during the year (for a minimum of 15 minutes).
This document will guide the user through the changes of the dielectric grease/coatings used in certain areas on all...
Read full bulletin
International vehicles built after 1/8/2018. International's Electrical Engineering Team made this change to improve the longevity of the OEM coatings and to improve applications at the factory.
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature.
Read full bulletin
Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
New CARB Idle Reduction Change Request
Engine replacements for all International engines will need to follow this procedure.
In some geographic areas, ambient temperatures reaching below 40F (4C), including high levels of humidity, an operator...
Read full bulletin
may experience engine stalling, low performance, and/or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
In some geographic areas, ambient temperatures reaching below 15F (-10 C), including high levels of humidity, an...
Read full bulletin
operator may experience engine stalling, low performance, and or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists all the currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
Title: Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure Applies...
Read full bulletin
To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or Clean Idle Sticker, Clean Truck Check
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
Applies To: All Navistar Powered Trucks Requesting Engine Emission Label Replacement, Certificate of Conformance and/or...
Read full bulletin
Clean Idle Sticker, Clean Truck Check
This document will guide a user to replace and reroute Charge Air Cooler (CAC) for vehicles built with the Cummins ISB...
Read full bulletin
and B6.7 engines.
The purpose of this document is to guide a user to resolve fault code 285 & 286 for Cummins engines.
Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or...
Read full bulletin
PSI engine.
How to request a horsepower quote; all International and Cummins engines
Starter kicks out after 1 second on MV and HV with Cummins L9 Engines
Cummins B6.7 and L9 engines with codes 285 and 286
Per agreement with EPA and CARB, Cummins, Inc.
Read full bulletin
provided an emergency calibration for Cummins ISB, B6.7, ISL9, L9, and X15 engines when a DEF Quality Sensor (DQS) was not available. This action addressed the Diesel Exhaust Fluid (DEF) Quality Sensor failures in the field and the unavailability of parts due to the worldwide chip shortage. This recall is step two of this program designed to revert all affected vehicles back to the certified calibration and to provide them with the latest improved DQS and Coolant Control Valve (CCV) designs. Additionally, the emergency calibration and the restoration to the certified calibration with the latest improved DQS and Coolant Control Valve (CCV) designs have no effect on vehicle Emissions.
Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI...
Read full bulletin
engines or Cummins ISB engine with Allison transmissions
QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
QLS Emergency Calibration.
Read full bulletin
applies to 2016 and newer Cummins B6.6, X15, and L9 engines and all A26 engines
QLS Emergency Calibration; Models equipped with 2016 and newer Cummins B6.7, X15 and L9 engines or International A26...
Read full bulletin
engine.
QLS Emergency Calibration; Models with 2016 Cummins ISX, A26 and EPA 2017 and newer Cummins X15, L9, or B6.7 engines
Engine Oil Capacities.
Read full bulletin
All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
QLS Emergency Calibration.
Read full bulletin
Only models with EPA 2017 and newer Cummins X15, L9, or B6.7 engines
The grid heater relay may stick closed resulting in a battery draw.
Read full bulletin
Only equipped with Cummins ISB engines.
On certain trucks equipped with an automatic transmission, if the automatic transmission is still in drive or reverse...
Read full bulletin
position and the stationary PTO switch is engaged, the engine RPM will ramp up and may overcome parking brake hold capability resulting in possible vehicle movement.
Fuel Filters, Winter Additives, and Blending Fuels for Cummins Engines
Reduced ISB Engine Exhaust Brake Efficiency; Only vehicles with Allison 1000/2000 series transmissions
On certain trucks equipped with an automatic transmission, if the automatic transmission is still in drive or reverse...
Read full bulletin
position and the stationary PTO switch is engaged, the engine rpm could ramp up and may overcome parking brake hold capability resulting in possible vehicle movement.
Auxiliary Engine Speed Control Cannot Hold Engine Speed When Using Steering Wheel Switches
Identifying the Source of Oil Seen at the Lower Flywheel Housing Area.
Read full bulletin
Only models equipped with Allison Transmission and International A26 or Cummins L9 engines
Oil Capacities; All Electronic International Engines 1994 - Present.
Read full bulletin
Cummins ISB, ISM & ISX
Wabco OnGuard Software Update; Only 500k baud rate Units with Wabco OnGuard with Cummins Engines built before 9-24-2018.
Voltage gauge drops on cold engine start-up; Only models built with Cummins ISB, B6.7, ISL, or L9 engines
Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
ISB Starting System Diagnostics; Only models built with cummins ISB engines
After ignition key off, the Transmission Control Module (TCM) may experience memory loss and may not allow engine...
Read full bulletin
restart.
Certain HV & MV trucks may have been built with an Instrument Panel (IP) harness without the Auto Neutral return wire to...
Read full bulletin
the interconnection to the engine harness.
Engine Oil Capacities All Electronic International Engines 1994 - Present.
Read full bulletin
Cummins ISB, ISM & ISX
Other
36 bulletinsThis document will guide the user through troubleshooting steps to submitting a case file for a horsepower request.
This document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes.
Read full bulletin
(Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
MODELS INVOLVED: International MV Series trucks
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
Switch Pack Programming Troubleshooting Information
This document will provide the user with cleaning options and procedures for aluminum bright work parts that become...
Read full bulletin
stained or tarnished.
Cummins ISB Starting system diagnostics.
J1939 Data Link Source Address Information
Diagnosis of chassis wander complaints.
J1939 Data Link Source Address Information
J1939 Data Link Troubleshooting
Telematics installation guidelines - Only units with 500K data link
J1939 Data link source address information
Pico Scope CCOS (Crankcase Separator Test)
PicoScope Test One Channel RCT
PicoScope Test Resistance and Ohmmeter
PicoScope Test for Datalink (CAN) Health Shorts & opens
J1939 Data Link Source Address Information
J1939 Data Link Troubleshooting
How to obtain As built parameter list
Bendix Stability control - customer satisfaction performance improvement; Specific Emergency / Tanker applications only.
Cab Lean Concern
Driveline Information Center and Troubleshooting Procedures
Dielectric Grease Change
Cleaning and Disinfecting Trucks and Buses
J1939 Data Link Troubleshooting
LT RH HV MV Wire Terminal Information
Cummins ISB Fan Drive Belt Chirp; Cummins ISB and Cummins B6.7
J1939 Data Link Source Address Information
SCR Vehicles Setting DEF Quality Faults due to Crossed DEF Tank Coolant Lines or Inverted DEFTHV
City Horn Difficult to Active
Wire Terminal Information
Driveline Information Center and Troubleshooting Procedures
Wire Terminal Information
Telematics Installation Guidelines; only Units with 500K Data Link
Electrical
27 bulletinsCertain International trucks and IC BusTM CE Series buses may have out of date BCM programing that may cause erroneous...
Read full bulletin
fault codes after a vehicle sits for 2 or 3 days.
Certain International trucks and IC BusTM CE Series buses may have out of date BCM programing that may cause erroneous...
Read full bulletin
fault codes after a vehicle sits for 2 or 3 days.
This document is to inform dealers, customers, and body builders/TEMs of a known BCM software issue with kernels 747 through 752.
Read full bulletin
Units built after November of 2024 as well as older units that were updated with DLB between 11/5/2024 and 6/26/2025 with Remote Power Modules (RPM) modules, can experience loss of RPM functionality as well as other electrical system concerns. Kernel 753 was released to DLB on 6/26/2025 to address these concerns.
This document is to inform dealers, customers, and body builders/TEMs of a known BCM software issue with kernels 747 through 752.
Read full bulletin
Units built after November of 2024 as well as older units that were updated with DLB between 11/5/2024 and 6/26/2025 with Remote Power Modules (RPM) modules, can experience loss of RPM functionality as well as other electrical system concerns. Kernel 753 was released to DLB on 6/26/2025 to address these concerns.
This document provides: Steps to take when switch pack programming fails, or when switch pack disappears after body...
Read full bulletin
control module update Sample scenarios Additional information to assist readers in understanding DLB switch pack programming
Title: Erratic BCM and RPM Behavior with Kernel 747-752 Applies To: All MV, HV, HX with RPM modules
Title: Battery Disconnect Switch Replacement - Best Practices Applies To: All Models with Battery Disconnect Switch
This document details the procedure that must be followed to ensure proper alternator troubleshooting.
This document covers battery diagnostics, maintenance and storage requirement.
Cummins B6.7 Grid Heater Relay
General Wheel Speed Sensor Troubleshooting
N2 telematics module not communicating with OCC systems.
Read full bulletin
Only models built with feature codes 10ADT, 10AEY, 10AEU, 10AEZ, 10AGB, or 10AGC built from 04/04/2019 through 11/01/2022.
PicoScope Wheel Speed Sensor Test
PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
New or replacement body control Module (BC,BCM) not detected; Gen 4 BCM
General wheel speed sensor troubleshooting
Cummins B6.7 Grid Heater Relay
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
Multi Module Programming Information for In-Cab Modules
Multi Module Programming Information for In-Cab Modules
Ambient Air Temperature (AAT) Sensor Faults/Location/Diagnostics
Multi Module Programming Information for In-Cab Modules
Multi Module Programming Information for In-Cab Modules
Tool Instruction - BCM Programming Harness
Body Builder Accessories Backfeeding Ignition Voltage
Multi Module Programming Information for In-Cab Modules
Body & Paint
26 bulletinsIn some instances, the driver's or passenger's door pod may become unresponsive, where it will not respond to any manual...
Read full bulletin
inputs from the driver or passenger. In some of these situations, it is possible for this symptom to be present without any fault codes becoming active. This article will guide the user through performing a hard reset of a door pod, which can restore the door pod to its operational condition, thereby avoiding the need for replacement. The steps in this article should be performed BEFORE diagnostics are completed for any active faults.
This article addresses chassis lean conditions on all chassis.
Read full bulletin
This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
Cab water leak trouble shooting tips
Water leaks past plastic vapor barrier sheet in the inner cavity of the cab entry door
Cab water leak troubleshooting tips; HX with steel cab only
Cab water leak troubleshooting tips
Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
Day cab roof air deflector causing loud vibration noise at highway speed
Programming Procedure for Center Panel Switch Packs
Programming Procedure for Center Panel Switch Packs
Programming Procedure for Center Panel Switch Packs
Programming procedures for the center panel switch packs has changed.
Chrome Plated C-Loop Mirror Flat Glass Cracks
Windshield Replacement on trucks equipped with Lane Departure Cameras; Only RH, LT, and Medium duty with feature codes...
Read full bulletin
008TTG, 0008TPU, 0008TTT, 0008TTU
Day Cab Roof Air Deflector Vibrates against Cab Roof; only models with P/N 4067947C92 Roof Air Deflector
Water Leaks Past Plastic Vapor Barrier Sheet in the Inner Cavity of the Cab Entry Door
Wind noise at upper side of cab door due to door out of alignment
Cab Door Latch Stuck, Door will not open
Body Controller Updates for 500k Baud Data link
Cab Door Latch Stuck, Door will not open
Cab Water Leak Troubleshooting Tips; Excluding 9000i, PayStar(HX), CityStar, or LoadStar
The First Check to make when Troubleshooting any Body Controller or ESC Issue
Hood Gap and Alignment Tolerances
Heated Mirror Timer Programmable Parameter; only models with feature code 0597006 and built prior to January 23, 2019
Vehicle Speed ( VSS ) Output for Bodybuilders
Hood Gap and Alignment Tolerances
Transmission
16 bulletinsThis document is to notify the field of an issue with BCM that causes various electrical system concerns after the vehicle sits for 2-3 days.
Read full bulletin
This can affect all LT, RH, MV, HV models, 2021MY and up HX, 2024MY and up CE Bus with BCM kernel version 752, 753, and 754. Vehicles built or updated with DLB between 6/1/25 and 11/4/25 are suspected of having these kernels installed on the BCM. The most common complaint is that the steering wheel switches do not function, which, depending on the vehicle model and options, can cause the bus door, pupil warning lights, radio controls, marker interrupt, and cruise control to stop working. Other complaints can include short circuit faults from multiple sensor circuits attached to the BCM setting at the same time, the vehicle will not go into gear, the headlights are stuck on, the brake lights are stuck on, or the parking brake alarm is sounding (horn chirping) with the parking brake set. As of 11/4/25, these symptoms can be resolved by updating the BCM to kernel 755 or later with DLB.
Title: Steering Gear Seal Repair Guidelines Applies To: Steering gears
Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
This document will guide the user through repair direction to configure Transmission Control Module (TCM) to provide the...
Read full bulletin
correct transmission gear range monitor value to the Premium or Base Electronic Gauge Cluster (EGC).
Procision Transmission No Start, stuck in gear, and service lamp; only models with Trans Feature codes 13GBX, 13GBY,...
Read full bulletin
13GBZ, 13GCA, 13GYU, 13GYV, 13GYW, 13GYX and software level 5567510.
International; HV, HX, LT, MV, RH, LS, ProStar, TranStar, WorkStar; It is possible for an internal clutch finger to fail...
Read full bulletin
after Safety Recall 18518 was completed. This campaign is only for this failure mode and these conditions. Clutches that are replaced under this field campaign but do not exhibit this type of failure will have the warranty claim charged back to the servicing location.
Power Take Off (PTO) Programming on Models with the Eaton Procision Transmission; Only with feature codes 13GBX, 13GBY,...
Read full bulletin
13GYU, 13GYW, or 13WEP
The upper shift lever may contact floor park brake shroud when in reverse gear.
Power Take Off (PTO) Programming on Models with the Eaton Procision Transmission; Only with feature code 0013GBX,...
Read full bulletin
0013GBY, 0013GYU, 0013GYW, or 0013WEP
Required Procedures for Procision Transmission Replacement; only models built with feature code13GBX, 13GBY, 13GBZ,...
Read full bulletin
13GCA, 13GYU, 13GYV, 13GYW, or 13GYX
Heavy Duty Clutch May Not Acheive Full Departure
ECA Clutch Departure
Eaton Bulletin for their ECA Clutch issue referenced from IK1100033 and IK1100034
An internal component within the clutch assembly may fail, which in special circumstances could inhibit clutch...
Read full bulletin
disengagement resulting in the transmission to not achieve neutral when commanded by the driver.
EATON ECA Clutches - Refer to CLIB0034
EATON ECA Clutches - EATON document referenced from IK1300170
Infotainment
9 bulletinsThis tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files.
Read full bulletin
It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
Radio Diagnostics and Information
NEW Ultrasonic DEF Head Unit; All SCR vehicles
NEW Ultrasonic DEF Head Unit available; Only models equipped with SCR Aftertreatment.
NEW Ultrasonic DEF Head Unit; Only vehicles Equipped with SCR
NEW Ultrasonic DEF Head Unit; only models equipped with SCR Aftertreatment
NEW Ultrasonic DEF Head Unit
Radio Diagnostics and Information
Trucks equipped with a sound package that has Bluetooth capability may have been built without front speakers.
Suspension
6 bulletinsThis article addresses chassis lean conditions on MV with IROS suspension.
Read full bulletin
It does not include any diagnostics for body leans, such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean.
This document reminds technicians of the critical relationship between the truck's suspension and the driveline operating angles.
Read full bulletin
The information applies to diesel, gas, and electric vehicles.
Front cab mount bushings/insulators MV, HV, DuraStar, and WorkStar vehicles used in severe vocations
Certain MV Series trucks built with Feature codes 14GVJ, 14GVX, or 14GVY (Axle rear tandem, Meritor MT 40 series) and...
Read full bulletin
with 14UNU (Suspension, rear air tandem 6X4 IROS) may have less than optimal driveline operating angles and this procedure is intended to improve inter axle differential reliability.
Suspension Lean Diagnostics; All models
Certain MV Series and DuraStar models may have been built with an incorrect spacer for the left-side front axle spring...
Read full bulletin
resulting in a lean condition.
Brakes
6 bulletinsThis document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and...
Read full bulletin
windshields using an ultrasonic sound detector.
This document is to guide users to eliminate brake pedal rattle noise.
Horizon Cab Door Field Replacement and the Side Window Air Deflectors.
Read full bulletin
NOTE: This article will only be applicable to cabs with the deflector mounted on the door pillar. If the cab has the deflector at the windshield, this article does not apply.
Air Powered (SAAR) Park Brake Troubleshooting (Service "P" Light Coming on).
Read full bulletin
Only models with hydraulic brakes
If a truck is operating with a trailer attached and the electrical connection is made between the truck and the trailer,...
Read full bulletin
the trailer brake lights in the combined stop/turn lamps may not illuminate when the truck service brakes are applied.
The spring actuated parking brake chamber may have been improperly crimped to the service brake chamber section of the...
Read full bulletin
brake chamber assembly resulting in an air leak in the service brake and possible separation of the spring brake chamber.
HVAC & Climate
6 bulletinsTitle: A/C Refrigerant and Oil Capacities Applies To: All current models
Air Compressor Inlet Hose Chaffing / Leaking
A/C Refrigerant and Oil Capacities
Air Pressure Gauges and A/C Pressure Transducer Troubleshooting
Air Pressure Gauges and A/C Pressure Transducer Troubleshooting
A/C Refrigerant and Oil Capacities
Tires & Wheels
4 bulletinsTire Pressure Monitoring system; Feature Codes 16VLS, 16VUY, 16VVA, 16VVM, or 16VUZ
Tire Pressure Monitoring systems (TPMS); Only LT, RH, HV, HX, or MV series trucks with feature code 16VLS, 16VUY,...
Read full bulletin
16VVA,16VUZ, or 16VVM
16VLS, 16VUY, 16VVA, and 16VUZ Tire Pressure Monitoring System (TPMS).
Suggested alignment target values when performing a vehicle axle alignment
Lighting
3 bulletinsLane Departure Warning Alert Active with Turn Signals On; Only models equipped with Lane Departure Warning
Repair Procedures for Vehicles Struck by Lightning
Incorrect Turn Signal Cancellation Feature
Pre-Delivery & Maintenance
2 bulletinsTitle: Service Portal iKNow Feedback Case Types Applies To: All
Frame Rail Straightness Inspection Procedure
Software & Calibration
2 bulletinsQLS Emergency Calibration Revert Process
QLS Emergency Calibration Revert Process
Fuel System
2 bulletinsWinter Fuel Or Additive Use Required Pop-Up Message
Identifying customer HVAC performance concerns / Evaporator Freeze up
Hybrid & EV
1 bulletinISB 6.7 Frequent Regeneration