2019 Infiniti Qx80 TSBs

2015-2018 Q50 Hybrid (HV37) 2017-2022 Q60 (CV37) 2015-2019 Q70 (Y51) 2015-2018 Q70 Hybrid (HY51) 2019-2024 QX50 (J55) 2022-2024 QX55 (FJ55) 2015-2021 QX60 (L50) 2022-2024 QX60 (L51) 2015-2019 QX60 Hybrid (L50H) 2015-2024 QX80 (Z62) SERVICE INFORMATION The AEB system is designed to turn itself OFF during driving conditions (e.g., rain, snow, fog, etc.) that obstruct its sensors. This behavior is normal, and no repairs should be performed. When the AEB system performs an intentional shutdown, the customer may state the following: The ICC stopped working while driving, The AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), The message Unavailable Front Radar Obstruction or Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owners Manual

cannot be performed, (continued on the next page)D

has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly (fuel pump assembly). The fuel level sensor can be replaced separately. P0460 (FUEL LEV SEN SLOSH) P0461 (FUEL LEVEL SENSOR) P0462 (FUEL LEVL SEN/CIRC) P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

quick charge function, the ignition should never be ON, or turned ON, while charging. Attempting to start the vehicle, or turning the ignition ON, while using the high amperage quick charge could potentially damage the fuel pump control module. Only turn the ignition ON when either the ESM or a technical service bulletin service procedure states to do so, and only while using a battery maintainer or smart charger set to reflash mode, or a similar setting. Battery voltage should not exceed 16V during a reprograming operation.

safety, security and satisfaction of our clients and is conducting a quality review of specific repairs for a previously completed campaign (R1912). If the VIN displays QA campaign ID PC838, retailers should perform the procedure attached to this communication even if the National Service History indicates the remedy action was previously performed for the vehicle. VINs identified with this QA campaign ID are being inspected to ensure the recall remedy was performed and documented in accordance with INFINITIs quality standards. ***** What Retailers Should Do ***** PLEASE FOLLOW THE ATTACHED PROCEDURE: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History Open Campaigns I.D. PC838. 2. Retailers should complete this action on both retailed vehicles and previously owned vehicles within retailer inventory. Retailers should follow all stop sale and do not drive, loan, sell, or trade instructions for campaigns. 3. Retailers will need to file the appropriate claim using applicable Op Code information in the repair procedure attached to this announcement to close the campaign. NOTE: Parts replaced under this activity will be placed on parts return. Monitor the Warranty Parts Return Website located at NNAnet.com for notifications.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

values in Table A on page 4 must be used. For all other models, consult the Electronic Service Manual (ESM). The following CONSULT-III plus (C-III plus) figures and steps are only provided to indicate where the VEHICLE REFERENCE VALUE from Table A is to be entered. The entire camera aiming procedure must be followed to complete the aiming procedure. Refer to the Electronic ESM section: CRUISE CONTROL & DRIVER ASSISTANCE > DRIVER ASSISTANCE SYSTEM > DRIVER ASSISTANCE SYSTEM > BASIC INSPECTION > LANE CAMERA UNIT > CAMERA AIMING ADJUSTMENT. 1. Turn the ignition ON. 2. From the C-III plus home screen, select Diagnosis (One System).

ACTION 1. Perform the appropriate diagnostic and repair procedure according to the ESM. 2. Reprogram the ECM, if applicable. The ECM reprogram in this Service Procedure is not a repair for the DTC, but instead updates the way the permanent DTC is stored and allowed to be erased. The DTC must be properly diagnosed and repaired before the reprogram is applied.

ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

OR The customer commented that the vehicle would not start. ACTION A. Test the vehicles 12 volt battery using the Midtronics DSS-5000. B. Refer to step 2 on page 2 to confirm this bulletin applies to the vehicle you are working on. C. If this bulletin applies, reprogram the ECM.

reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. Refer to SERVICE PROCEDURE on the next page. HINT: OCS may also be referred to as ODS. 2. Perform 75-zero RESET.

RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.

flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.

See Amendment History on the last page. Please discard previous versions of this bulletin.

to the Service > Campaign screen: Custom VIN Campaign Report. The tool identifies open campaigns on a customized VIN list loaded into DBS for INFINITI and Nissan vehicles. The following personnel will have access to this tool: - Retailer: Executive Managers, Service Managers, and/or Service Directors - Regions: Regional Aftersales Manager (RAM), Area General Manager (AGM), Fixed Operations Manager (FOM), Regional Service Operation Managers (RSOM), and Retailer Technical Specialist (DTS) The VINS can be loaded individually or up to 10,000 VINs at a time. If you have more than 10,000 VINs, each incremental VIN file of 10,000 or less VINs will need to be loaded prior to selecting the Check For Open Campaigns option. The report can be viewed on screen or exported to Microsoft Excel and will identify the following for each VIN loaded into the tool: - Open Campaigns (ID and description) - Model Code, Model, and Model Year - Current Repair Status Blank: Repair order (RO) has not been opened yet Unrepaired: RO has been opened for the campaign, but not closed or submitted o Repaired: RO for the campaign has been closed and a warranty claim has been submitted - Current Claim Status o Blank: RO still open o Unsubmitted: A warranty claim for the campaign repair has not been submitted o Submitted: A RO has been closed and a campaign warranty claim has been submitted for payment o Suspended: The campaign warranty claim has suspended for one or more errors o Rejected: The campaign warranty claim has been denied for some reason (by retailer or NNA) o Paid: A campaign warranty claim has been submitted and paid by NNA, but the vehicle has not yet been removed from the NNA open campaign vehicle table - Stop Sale Applicability - Parts Restriction Applicability (If restricted, SVC order must be used to acquire parts)

Please discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

an applied vehicle, follow the SERVICE PROCEDURE in this bulletin to determine if the origin of the leak is at the rear extension seal, or at the pressed-in plug of the propeller shaft sleeve yoke (Figure 1).

UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicles 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

engine is running, when turning the steering wheel, or when driving at parking lot speeds. ACTION Adjust the clearance between the heat shield above the exhaust front tube (RH) and the frame to 10 mm, AND Adjust the clearance between the rear cooler and heater pipe assembly and the heat shield above the exhaust front tube (RH) to 6 mm.

voluntary service campaign on certain specific model year 2019 Q70 and 2019 QX80 vehicles. The Engine Control Module (ECM) will be inspected, and reprogrammed if it applies. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification number P0A06 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. RETAILER RESPONSIBILITY Retailers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a retailers inventory.

INFINITI InTouch Services App to start the vehicle (Remote Engine Start), the windshield wipers are activated regardless of rain. ACTION 1. Replace the Body Control Module (BCM) with one listed in the PARTS INFORMATION on page 3. 2. Configure the BCM. 3. Perform the initialization procedure for NATS to relearn all of the customers Intelligent Keys. 4. Erase any stored DTCs.

conducting a Voluntary Service Campaign to reprogram the engine control module (ECM) with countermeasure software in certain INFINITI 2019 model year Q70 and QX80 vehicles. The current software installed may allow the Variable Valve Timing (VVT) solenoid valve diagnosis to continue to draw current when the engine is off. This condition may result in a reduction of the battery life. ***** What Retailers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Service Campaign using Service Comm or DBS National Service History Open Campaign I.D. P0A06 - New vehicles in retailer inventory can also be identified through the attached VIN list or by using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to IPSB 15-286 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Retailers are requested to repair any affected vehicles in retailer new or pre-owned inventory to ensure client satisfaction. 3. Retailers should use ITB20-013 to correct any vehicles subject to this campaign. 4. Once repaired, retailers should submit the claim, using the claims coding provided, and release the vehicle.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.

occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of ITB23-010.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of ITB23-010.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and bug fixes. IMPORTANT: If the client is experiencing a software related concern, refer to ITB21-011 to verify if the client concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Unit (DCU) needs to be replaced on an APPLIED VEHICLE for any reason, follow the steps in the Service Procedure to: - Confirm proper diagnosis and repair with TECH LINE to obtain DCU order approval, then place the order with DENSO. NOTE: The DCU order approval process does not apply to 2017 model year and earlier models. TECH LINE authorization is not needed for 2017 model year and earlier models. - Configure the Multi AV system. - 2018-2019 QX30 vehicles only: Register the replacement DCU. DCU registration is necessary whether or not the vehicle has an active Infiniti InTouch Apps subscription. NOTE: The original DCU must be installed in the vehicle while performing part of this procedure. DO NOT remove the original DCU until instructed.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.

This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The new service part (B in Figure 1) is visually different, but is a direct replacement for the original equipment part. IMPORTANT: See page 2 for the procedure to inspect the cap bolt service part for excessive stretch. If replacement of a single connecting rod cap bolt is indicated for any given connecting rod, both connecting rod cap bolts of the affected connecting rod must be replaced as a set.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (cv Joint Boot Kit) availability. If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the retailer. If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to ITB21-002 to prevent Drive Shaft thread damage.

between 20 40 mph, OR RPM flare / slip feeling / vibration during or immediately after a 2 3 upshift or 3 4 upshift with light or moderate throttle input. ACTION Replace the Torque Converter.

conducting a retailer inventory quality action on to inspect 6 specific 2019 INFINITI Q50 and 43 specific INFINITI QX80 vehicles identified in Service Comm, to inspect the transmission torque converter. Affected vehicles are subject to a stop sale and are either currently in retailer inventory or assigned and in transit to the retailer. ***** What Retailers Should Do ***** PLEASE FOLLOW THE ATTACHED INSPECTION INSTRUCTIONS 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History Open Campaign I.D. P9331. - New vehicles in retailer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). o Refer to IPSB 15-286 for additional information - Please continue to check newly arriving inventory for campaign applicability. 2. Please do not drive, sell, loan or trade the specific vehicles in Retailer Inventory subject to this Quality Action. 3. Use the attached procedure to inspect the vehicle: - If the data shows the Torque Converter Clutch Solenoid Monitor (TCC SOL MON) increases to 0.4A during steady cruise at or above 25MPH, no further action is necessary - File a claim for the inspection, and release the vehicle for sale

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.

See Amendment History on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

equipped with INFINITI InTouch (Intelligent Key). SERVICE INFORMATION An Intelligent Key, for the applied vehicles with INFINITI InTouch?, has the abillity to trigger specific customized settings for the radio, clock, heating and air conditioning (HVAC) and navigation that are unique to that key, and each Intelligent Key for a specific vehicle may have different settings stored. EXAMPLE: The vehicle may be driven by more than one person, and each driver has a personal Intelligent Key. Each driver may adjust their preferred vehicle settings differently. If two or more Intelligent Keys with different stored settings are unintentionally interchanged, one or more of the following perceived issues might be reported by the customer(s). - Radio ? Presets are lost or change - Clock ? Settings are not showing the correct time due to day-light savings or the selected region (time zone) - HVAC ? Controls are set differently - Navigation ? Settings suddenly altered If any of these perceived issues are present: - Confirm if there are multiple Intelligent Keys being used by the customer(s) interchangeably, and if so, verify that each key?s settings are different. NOTE: Customer may not recognize that different Intelligent Keys are linked differently.

steering wheel while turning and only at speeds between 1-9 MPH. ACTION Replace the power steering high pressure piping with the part listed in the Parts Information on page 6. IMPORTANT: Inform the customer that this repair will reduce, but does not eliminate the amount of judder felt in the steering wheel during low speed parking lot maneuvers.

trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.