2016 Infiniti Qx80 TSBs

2015-2018 Q50 Hybrid (HV37) 2017-2022 Q60 (CV37) 2015-2019 Q70 (Y51) 2015-2018 Q70 Hybrid (HY51) 2019-2024 QX50 (J55) 2022-2024 QX55 (FJ55) 2015-2021 QX60 (L50) 2022-2024 QX60 (L51) 2015-2019 QX60 Hybrid (L50H) 2015-2024 QX80 (Z62) SERVICE INFORMATION The AEB system is designed to turn itself OFF during driving conditions (e.g., rain, snow, fog, etc.) that obstruct its sensors. This behavior is normal, and no repairs should be performed. When the AEB system performs an intentional shutdown, the customer may state the following: The ICC stopped working while driving, The AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), The message Unavailable Front Radar Obstruction or Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owners Manual

cannot be performed, (continued on the next page)D

has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly (fuel pump assembly). The fuel level sensor can be replaced separately. P0460 (FUEL LEV SEN SLOSH) P0461 (FUEL LEVEL SENSOR) P0462 (FUEL LEVL SEN/CIRC) P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

quick charge function, the ignition should never be ON, or turned ON, while charging. Attempting to start the vehicle, or turning the ignition ON, while using the high amperage quick charge could potentially damage the fuel pump control module. Only turn the ignition ON when either the ESM or a technical service bulletin service procedure states to do so, and only while using a battery maintainer or smart charger set to reflash mode, or a similar setting. Battery voltage should not exceed 16V during a reprograming operation.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

sonar activates with no obstacle ahead), inspect the front license plate, front license plate frame and if equipped, the front license plate bracket. See page 2 for example photos. The front sonar parking sensor may activate if: The front license plate is bent outward from its bracket (there is a gap between the license plate and the bracket) OR the front license plate frame is bent or loose and is hanging outward, away from the license plate and/or bracket (there is a gap between the license plate frame and the license plate and/or bracket) OR the bracket is loose and is hanging outward, away from the bumper (there is a gap between the bracket and the bumper). If any of these conditions are found, correct it by removing the gap (straighten the license plate, straighten and/or secure the license plate frame, or secure the bracket, as it applies). - Retest the operation of the front sonar parking sensor. If the issue is not resolved, go to ASIST and the related Electronic Service Manual (ESM) for further diagnosis. See this bulletin for further detail.

Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.

This bulletin gives an outline of the retailer technician?s responsibilities in assisting the retailer claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ACTION 1. Confirm the current ECM part number. 2. Reprogram the ECM, if applicable.

reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. Refer to SERVICE PROCEDURE on the next page. HINT: OCS may also be referred to as ODS. 2. Perform 75-zero RESET.

RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.

flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.

tool to the Service > Campaign screen: Retailed Vehicle Open Campaign Report on July 9, 2018, which identifies owner contact information for specific campaigns. Currently, only Takata campaign owner lists are available. The following personnel will have access to this tool: - Retailer: Dealer Principal, Executive Managers, General Managers, Parts/Service Managers, and/or Parts/Service Directors - Regions: Regional Aftersales Manager (RAM), Regional Operations Managers (ROM), Fixed Operations Manager (FOM), Dealer Operation Managers (DOM), Regional Service Operation Managers (RSOM), and Client Experience Managers (CEM) The report can be viewed on screen or exported to Microsoft Excel and identifies the following: - VIN - Campaign ID & Campaign Description - Model & Model Year - Data Source o Up to three data sources can be provided for each VIN - RO Info: If this VIN has visited an Infiniti retailer anywhere in the U.S. within the last twelve months, the RO information will be displayed. - Campaign Mailing List: This is DMV data for the VIN listed - Marketing List: If an owner is on your marketing list, their contact information from that list will be displayed here. DMV data is not used for marketing list owner information. - Contact Name - Last Name/First Name & Address (City, State, Zip) - Phone (1-3) & Email (1-3) - Remove Flag o This defaults to ?N? unless the retailer or INFINITI USA flags this VIN for removal. o The removed information will still show on the DBS screen and exported report, but can be filtered on the exported file to only display the records with ?N? in this column.

to the Service > Campaign screen: Custom VIN Campaign Report. The tool identifies open campaigns on a customized VIN list loaded into DBS for INFINITI and Nissan vehicles. The following personnel will have access to this tool: - Retailer: Executive Managers, Service Managers, and/or Service Directors - Regions: Regional Aftersales Manager (RAM), Area General Manager (AGM), Fixed Operations Manager (FOM), Regional Service Operation Managers (RSOM), and Retailer Technical Specialist (DTS) The VINS can be loaded individually or up to 10,000 VINs at a time. If you have more than 10,000 VINs, each incremental VIN file of 10,000 or less VINs will need to be loaded prior to selecting the Check For Open Campaigns option. The report can be viewed on screen or exported to Microsoft Excel and will identify the following for each VIN loaded into the tool: - Open Campaigns (ID and description) - Model Code, Model, and Model Year - Current Repair Status Blank: Repair order (RO) has not been opened yet Unrepaired: RO has been opened for the campaign, but not closed or submitted o Repaired: RO for the campaign has been closed and a warranty claim has been submitted - Current Claim Status o Blank: RO still open o Unsubmitted: A warranty claim for the campaign repair has not been submitted o Submitted: A RO has been closed and a campaign warranty claim has been submitted for payment o Suspended: The campaign warranty claim has suspended for one or more errors o Rejected: The campaign warranty claim has been denied for some reason (by retailer or NNA) o Paid: A campaign warranty claim has been submitted and paid by NNA, but the vehicle has not yet been removed from the NNA open campaign vehicle table - Stop Sale Applicability - Parts Restriction Applicability (If restricted, SVC order must be used to acquire parts)

within 15 feet of the vehicle, the BCM may continue to ?ping? the Intelligent Key keeping it awake. Keeping the Intelligent Key awake may result in discharging its battery in a much shorter period of time than normal (premature battery discharge). Example: The Intelligent Key should not be stored in a lock box or other storage container attached to the outside of the vehicle. To prevent premature Intelligent Key battery discharge, store the Intelligent Key more than 15 feet from the vehicle. If unable to store the Intelligent Key more than 15 feet from the vehicle (for example, when a vehicle is on display in the showroom); the following steps will prevent the BCM from continuing to ?ping? the Intelligent Key: - Disable the welcome light function using the on-board methods outlined in this bulletin, or - Disable the welcome light function using the CONSULT-III plus methods outlined in this bulletin. NOTE: If an Intelligent key is routinely stored within 15 feet of a vehicle while it is in dealer inventory, the Intelligent Key battery should be replaced before the vehicle is delivered to the customer. This will ensure the customer receives Intelligent Keys without premature discharge. Intelligent Key batteries replaced for this reason are not covered under warranty.

Service Campaign to disable (turn off) the 2G Telematics Control Unit (?2G TCU?). The subject QX56/QX80, JX35/QX60, M37/M56/Q70, and 2014-15 Q50 vehicles are equipped with Continental GEN1 TCU devices transmitting at 2/2.5G (GSM/GPRS/UMTS) frequencies and are designed to work with 2G cellular service. The 2G cellular service is no longer active in the United States. The subject 2G TCUs are no longer connected to telematics services and no longer perform any function in the affected vehicles. This campaign is being performed out of an abundance of caution to help safeguard against potential cybersecurity issues. - All eligible vehicles that enter the service department for any reason should have the subject 2G TCU deactivated. This campaign will be performed at no charge to the client for parts and labor. - Vehicles that have been upgraded to 3G TCUs are not subject to this campaign. - For clients interested in the 3G TCU upgrade as opposed to deactivation, please refer to ITB17-007 (PC451, PC452, or PC454)

Voluntary Service Campaign (in the U.S. ONLY) on certain specific 2013-2016 Infiniti vehicles equipped with 2G Telematics Hardware to disable the 2G Telematics Control Unit (TCU). The 2G cellular service is no longer active in the United States and the subject TCUs are no longer connected to telematics services (Infiniti ConnectTM) and no longer perform any function in the affected vehicles. This campaign is being performed out of abundance of caution to help prevent potential cybersecurity issues. - Applied vehicles equipped with the 2G Telematics Control Unit (TCU) that enter the service department for any reason should have the subject TCU deactivated. This campaign will be performed at no charge to the customer for parts or labor. - For customers interested in the TCU update as opposed to deactivation, please refer to ITB17-007. IDENTIFICATION NUMBER Infiniti has assigned identification number P7331 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a retailer?s inventory.

Please discard all previous versions of this bulletin.

manually folded/unfolded or bumped, the mirror body can become loose at the pivot point. If this occurs, the mirrors should be adjusted again electrically before driving. To readjust the mirrors, press the "CLOSE" switch (see Figure 1) until the mirrors are fully folded in, then press the "OPEN" switch until the mirrors are fully open. This mirror readjustment procedure is included in section 3 - Pre-driving checks and adjustments of the vehicle Owner?s Manual.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ACTION 1. Confirm that the battery voltage is 11 volts, or more, with the ignition ON (engine OFF, not running). 2. Erase DTC 3. Perform DTC confirmation steps in the Service Procedure. 4. Confirm 1st trip DTC P0603 is not stored. NOTE: P0603 is often the result of low battery voltage, discharged battery or battery terminal disconnections. Please see this bulletin for furtner details.

No other changes were made. Please discard previous versions of this bulletin.

UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicles 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.

The APPLIED VEHICLES section has been updated. No other changes have been made. Please discard all previous versions of this bulletin.

No other changes were made. Please discard previous versions of this bulletin.

An additional model year has been added to the Applied Vehicles and to Table A. Please discard all previous versions of this bulletin.

noise is coming from the engine fan coupling when the vehicle is operated at or below 32F (0C). ACTION 1. Confirm this bulletin applies. 2. Check and compare your Current ECM Part Number to Table A on page 4. 3. If the part number does not match one in Table A, this bulletin does not apply. Go back to ASIST for further diagnostic and repair information. 4. If this bulletin applies, reprogram the ECM.

and make changes to the body of the bulletin. Please discard previous versions.

The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

CHANGES HAVE BEEN MADE TO ITEMS 4 AND 13 IN THE SUPPLEMENTAL DIAGNOSIS TABLE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. SERVICE INFORMATION IF A CUSTOMER STATES THE REMOTE ENGINE START (RES) FEATURE OF AN APPLIED VEHICLE IS NOT WORKING, MAKE SURE THE SYSTEM IS PROPERLY SET TO OPERATE: -THE IGNITION IS TURNED OFF -THE SHIFT SELECTOR IS IN PARK (P) -THE HOOD/DOORS/TRUNK LID/LIFT GATE ARE COMPLETELY CLOSED -NO OTHER OF THE VEHICLES INTELLIGENT KEYS (I-KEYS) ARE INSIDE, OR WITHIN STARTING RANGE OF, THE VEHICLE -THE I-KEY/KEY FOB (KEY FOB) IS WITHIN THE OPERATING RANGE OF 197 FT OR 60 M IF THE ABOVE CONDITIONS ARE MET, RES SHOULD WORK. 1. POINT THE KEY FOB AT THE VEHICLE. 2. PRESS THE LOCK BUTTON. 3. PRESS AND HOLD THE RES BUTTON WITHIN FIVE (5) SECONDS OF PRESSING THE LOCK BUTTON UNTIL THE TURN SIGNAL LIGHTS TURN ON. WHENEVER AN APPLIED VEHICLE HAS A CONCERN WITH THE REMOTE ENGINE START (RES) FEATURE NOT WORKING PROPERLY, MAKE SURE TO VERIFY THE INCIDENT BEFORE STARTING ANY DIAGNOSIS AND/OR REPLACING PARTS. FOR A BETTER UNDERSTANDING OF THE RES SYSTEM, REFER TO SECTION 3: ""PRE-DRIVING CHECKS AND ADJUSTMENTS > REMOTE ENGINE START OF THE APPLIED VEHICLES OWNERS MANUAL. WHEN DIAGNOSING RES OPERATION, USE THE SUPPLEMENTAL RES SERVICE INFORMATION AND SUPPLEMENTAL DIAGNOSIS TABLE (STARTING ON PAGE 2) IN ADDITION TO THE ESM."

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Infiniti?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.

breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.

off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulleitn for further details.

The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further detail.

DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.

occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

A model year has been added to APPLIED VEHICLES. Discard all previous versions of this bulletin.

warranty information on page 2 has been updated. No other changes have been made. Please discard previous versions of this bulletin.

Also, warranty information on pages 1 and 8 has been updated. No other changes have been made. Please discard previous versions of this bulletin.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of ITB23-010.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of ITB23-010.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and bug fixes. IMPORTANT: If the client is experiencing a software related concern, refer to ITB21-011 to verify if the client concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.

This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.

No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard all previous versions of this bulletin.

SERVICE INFORMATION On February 26, 2016 Infiniti announced that it was sending a reminder notification to clients affected by AT&T?s planned discontinuation of the 2G cellular network. In June 2016, Infiniti communicated instructions to retailers to update new vehicles in their inventory with 3G compatible telematics control units. At this time, Infiniti is beginning the process of making 3G compatible hardware available to owners of affected vehicles as identified above. This upgrade may require an owner to make a co-payment in order to receive the 3G hardware update. Please refer to the Claims Information below to determine if an owner co-pay is required. This client satisfaction initiative includes both the hardware upgrade and a complimentary one-year subscription to Infiniti Connection Plus telematics service; this does not apply to PC454 (see page 2 for details). You MUST use Service Comm to confirm bulletin Applicability. NOTE: - Vehicle eligibility will be viewed on the second page of Service Comm. This activity is not displayed on the main page of Service Comm because it is optional for customers to participate. - Vehicles without Navigation are ineligible as they are not equipped with TCUs. Retailer?s Responsibility It is the retailer?s responsibility to check SERVICE COMM using the appropriate Service Comm I.D. for the status on each vehicle falling within the range of this client satisfaction initiative which for any reason enters the service department. If a vehicle subject to this client satisfaction activity was part of a retailer trade, the letter associated with that vehicle should be forwarded to the appropriate retailer for upgrade completion.

revised to include: - The telematics upgrade for 2014-15 Q50 is now available. The procedure and part information has been added to this announcement.. - Second page of Service Comm is not VIN specific, service personnel should check vehicle repair history prior to offering clients an opportunity to upgrade - In lieu of repair history, TCU version can be checked on the information screen (see page 2) Please discard previous versions of this announcement.

This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard all previous versions of this bulletin.

reboots when SXM Traffic is enabled. NOTE: Perform the steps in this bulletin ONLY if the above condition occurs while the vehicle is in the state of Oregon. ACTION Update the Navigation system software using the DVD shown on page 2.

MODIFICATIONS HAVE BEEN MADE TO INCLUDE QX30. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN."

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.

See Amendment History on the last page. Please discard previous versions of this bulletin.

We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.

We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.

The announcement from March 21, 2017 has been revised to include: - Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps - Customer expense may be applicable if the vehicle is out of warranty

announcement from March 21, 2017 has been revised to include: o Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps o Client expense may be applicable if the vehicle is out of warranty

Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

fueling the vehicle at different fuel stations (filling nozzle shuts off every few seconds while filling at multiple stations and using multiple filling pumps). IMPORTANT: - If the customer does not report the above symptoms, this bulletin does not apply. - If the customer reports intermittent (but not consistent difficulty re-fueling), this bulletin does not apply. ACTION: Perform the Inspection Procedure in this bulletin, starting on page 4, only if the customer reports symptoms as described above. NOTE: Refer to the Repair Overview on page 2.

The publication date has been revised to include the latest models and model years, and the Service Procedure has been updated. Please discard previous versions of this bulletin.

nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.

revised to include: - 283B0-3JA6A is the part number being used for all vehicles, except Q50 o This part supersedes the previous part (283B0-3JA5A). Retailers may continue to use the previous part until existing stock is exhausted. - 283B0-3JA7A is used for Q50 - These parts are not restricted and can be ordered through normal process Please discard previous versions of this announcement.

STATES THAT WHEN THE DISTANCE TO EMPTY INDICATOR DISPLAYS - - - AND THE LOW FUEL WARNING INDICATOR IS ON, THE FOLLOWING OCCURS WHEN ADDING FUEL TO THE FUEL TANK: - THE FUEL PUMP NOZZLE WILL SHUT OFF AUTOMATICALLY AFTER 18-20 GALLONS OF FUEL HAS BEEN ADDED TO THE VEHICLE."

THE PARTS INFORMATION SECTION HAS BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. IF YOU CONFIRM AFTER FILLING UP THE FUEL TANK TO FULL, THE FUEL GAUGE WILL DROP DOWN TO ABOUT 7/8 (SEE FIGURE 1) QUICKLY AFTER A SHORT DRIVE. ACTION REPLACE THE COMBINATION METER. -LOOK UP THE COMBINATION METER PART NUMBER USING THE VIN WITH WIN/FAST OR EQUIVALENT, AND THEN ORDER THE CORRESPONDING NEW PART NUMBER LISTED IN THE PARTS INFORMATION ON NEXT PAGE THROUGH MODEL ELECTRONICS. -REFER TO THE ELECTRONIC SERVICE MANUAL (ESM), SECTION MWI METER, WARNING LAMP & INDICATOR FOR REMOVAL AND REASSEMBLY."

CHANGES HAVE BEEN MADE THROUGHOUT THIS BULLETIN. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. IF YOU CONFIRM AFTER FILLING UP THE FUEL TANK TO FULL, THE FUEL GAUGE WILL DROP DOWN TO ABOUT 7/8 (SEE FIGURE 1) QUICKLY AFTER A SHORT DRIVE. ACTION REPLACE THE COMBINATION METER. -LOOK UP THE COMBINATION METER PART NUMBER USING THE VIN WITH WIN/FAST OR EQUIVALENT, AND THEN ORDER THE CORRESPONDING NEW PART NUMBER LISTED IN THE PARTS INFORMATION ON NEXT PAGE THROUGH MODEL ELECTRONICS. -REFER TO THE ELECTRONIC SERVICE MANUAL (ESM), SECTION MWI METER, WARNING LAMP & INDICATOR FOR REMOVAL AND REASSEMBLY."

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

receive a letter notification explaining how their vehicle?s Infiniti Connection features will be affected by AT&T?s planned discontinuation of the 2G cellular network.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

These items may be available from Infiniti by request if certain criteria are met. This bulletinlists the criteria and provides an application form for such replacements. See this bulletin for further detail.

See this bulletin for further detail.

when installing a new carpeted floor mat in an Applied Vehicle. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

and PC454 are no longer active. Repair orders opened after this bulletins published date are no longer eligible for reimbursement under Campaign ID # PC451, PC452 or PC454. Please discard all previous versions of ITB17-007.

The new service part (B in Figure 1) is visually different, but is a direct replacement for the original equipment part. IMPORTANT: See page 2 for the procedure to inspect the cap bolt service part for excessive stretch. If replacement of a single connecting rod cap bolt is indicated for any given connecting rod, both connecting rod cap bolts of the affected connecting rod must be replaced as a set.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

A correction was made to the Service Procedure on page 15. No other changes were made. Please discard previous versions of this bulletin.

Modifications have been made to include 2017 Q50, Q60, Q70, QX60, and QX80 vehicles. No other changes have been made. Please discard all previous versions of this bulletin.

stored: - P0090 (FRP CONTROL SYSTEM) And U1000 and/or U1001 DTCs are stored in one or more other control units. NOTE: If P0090 is set and U1000 and/or U1001 DTCs are not set, this Bulletin does not apply. Refer to the Electronic Service Manual (ESM) for further diagnostic information. ACTION Replace the IPDM with one listed in the Parts Information.

revised to include: - Campaign repair bulletin, ITB17-007 has been developed and is now available on NNAnet, and ASIST. Please discard earlier versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Ts 3G network connection, including Nissan Group, have had connectivity services affected. INFINITI Connection with InTouch Services are no longer available on the APPLIED VEHICLES listed above.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. The CLAIMS INFORMATION section has been corrected. No other change have been made. Please discard previous versions of this bulletin.

installed or VPC installed accessories. SERVICE INFORMATION The National Highway Traffic Safety Administration (NHTSA) requires that any automobile dealer that installs accessories on a vehicle prior to first retail sale must install a special label (?reduced capacity label?) on that vehicle if the total weight of all accessories on that vehicle exceeds 1.5 percent of the vehicle?s gross vehicle weight rating (GVWR) or 100 pounds, whichever is less. This includes accessories that the dealer installs (dealer installed factory accessories and dealer installed aftermarket accessories), and accessories installed at the Vehicle Processing Center (VPC) prior to the vehicle being delivered to the dealer. IMPORTANT: Failure to comply with this requirement may result in penalties imposed by NHTSA. Follow the instructions in this bulletin to help meet these requirements.

DISCONTINUATION OF THE 2G CELLULAR NETWORK. IN LATE SUMMER 2016, INFINITI PLANS TO PROVIDE FURTHER INFORMATION TO AFFECTED CLIENTS REGARDING OPTIONS TO HAVE THEIR TELEMATICS UNITS UPDATED. AT THIS TIME, INFINITI IS CONDUCTING A RETAILER INVENTORY SERVICE ACTION ON AFFECTED UNITS IN RETAILER INVENTORY TO REPLACE THE 2G-COMPATIBLE TELEMATICS CONTROL UNIT WITH A TELEMATICS CONTROL UNIT DESIGNED TO CONNECT TO THE AT&T 3G CELLULAR NETWORK. THE AFFECTED VEHICLES ARE EITHER CURRENTLY IN RETAILER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE RETAILER. INFINITI REQUESTS THESE VEHICLES BE UPDATED PRIOR TO SALE TO ENABLE CLIENTS TO ACCESS AVAILABLE INFINITI CONNECTION FEATURES, INCLUDING AUTOMATIC COLLISION NOTIFICATION AND EMERGENCY CALLING. THERE ARE APPROXIMATELY 142 Q50 VEHICLES IN RETAILER INVENTORY THAT ARE EQUIPPED WITH TELEMATICS CONTROL UNITS DESIGNED TO CONNECT TO THE 2G CELLULAR NETWORK. HOWEVER, THE HARDWARE UPGRADE SERVICE PROCEDURE IS NOT AVAILABLE AT THIS TIME. PLEASE DO NOT TAKE ANY ACTION AT THIS TIME ON Q50 VEHICLES THAT ARE EQUIPPED WITH A 2G-COMPATIBLE TELEMATICS CONTROL UNIT. FURTHER INSTRUCTIONS WILL BE PROVIDED AT A LATER DATE FOR THE TCU UPGRADE ON AFFECTED Q50 VEHICLES. INFINITI EXPECTS THIS COMMUNICATION TO OCCUR IN LATE SUMMER 2016. IMPORTANT: RETAILERS SHOULD NOT SELL OR TRADE ANY AFFECTED VEHICLES IN RETAILER INVENTORY SUBJECT TO THIS SERVICE ACTION UNTIL THE 3G-COMPATIBLE TELEMATICS CONTROL UNIT HAS BEEN INSTALLED."

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

IF YOU CONFIRM DTC C1116 (STOP LAMP SW) is stored (Past or Current), AND Customer stated VDC warning lamp was illuminated. ACTION Reprogram the ABS control unit (ABS) per the Service Procedure in this bulletin. - Refer to step 20 on page 8 to confirm that reprogramming is needed.

Also, tips for using the ProCut? brake lathe were added on page 8, and a Brake Noise Diagnostic Worksheet was added on page 10. Please discard previous versions of this bulletin.

found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (cv Joint Boot Kit) availability. If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the retailer. If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to ITB21-002 to prevent Drive Shaft thread damage.

You must read the entire bulletin to properly perform the repair. Please discard previous versions of this bulletin.

create a 7th gear to 3rd gear down shift. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm TCM reprogramming applies. 2. If it applies, reprogram the TCM.

Discard previous versions of this bulletin.

AND -APPLYING LIGHT TO MEDIUM THROTTLE (LESS THAN 50% THROTTLE). ACTION 1. REFER TO STEP 6 IN THE SERVICE PROCEDURE TO CONFIRM TCM REPROGRAMMING APPLIES. 2. IF IT APPLIES, REPROGRAM THE TCM."

Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90 (see Figure 1). Moving vehicles as shown in this bulletin will prevent tire Flat Spotting. See this bulletin for further detail.

The APPLIED VEHICLES were updated with new models and model years. No other changes have been made. Discard previous versions of this bulletin.

Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

some front wheel alignment specifications listed in the Electronic Service Manual (ESM), section FSU-Front Suspension, were listed incorrectly and have been corrected. - Updated ESMs will be distributed to the field as quickly as possible. - Until the updated ESMs are made available, please use the corrected specifications listed in this bulletin. - Specification areas that have corrections are outlined with a Red box on the following pages.

service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.

In 2016, INFINITI launched a Client Satisfaction Initiative (CSI) that provided clients with an opportunity to update the Telematics Control Unit (TCU) in vehicles equipped with a TCU designed to connect to the 2G cellular network. AT&T stopped accepting enrollments on the 2G cellular network, and discontinued its 2G cellular network coverage on December 31, 2016. Once the 2G cellular network was discontinued, there was no access to the INFINITI Connection features without a TCU hardware upgrade. Because AT&T will shut down its 3G network on December 31, 2021, INFINITI is discontinuing this Client Satisfaction Initiative to upgrade from 2G to 3G compatible hardware effective immediately. 3G services will continue to be provided until December 31, 2021. Vehicles equipped with a TCU that connects to the 3G cellular network will have no access to the INFINITI Connection features, including Emergency Calling and Automatic Collision Notification after that time. What Retailers Should Do Service Comm will deactivate PC451, PC452 and PC454 on any VINs on December 22, 2020. No further retailer action is required.

RETAILERS MAY SELL VEHICLES THAT HAVE NOT BEEN UPGRADED. PLEASE REFER TO ADDITIONAL Q&A SUPPLIED IN THIS DOCUMENT. PLEASE DISCARD EARLIER VERSIONS OF THIS BULLETIN. ON FEBRUARY 26TH, INFINITI ANNOUNCED THAT IT WAS SENDING A REMINDER NOTIFICATION TO CLIENTS AFFECTED BY AT&TS PLANNED DISCONTINUATION OF THE 2G CELLULAR NETWORK. IN LATE SUMMER 2016, INFINITI PLANS TO PROVIDE FURTHER INFORMATION TO AFFECTED CLIENTS REGARDING OPTIONS TO HAVE THEIR TELEMATICS UNITS UPDATED. AT THIS TIME, INFINITI IS CONDUCTING A RETAILER INVENTORY SERVICE ACTION ON AFFECTED UNITS IN RETAILER INVENTORY TO REPLACE THE 2G-COMPATIBLE TELEMATICS CONTROL UNIT WITH A TELEMATICS CONTROL UNIT DESIGNED TO CONNECT TO THE AT&T 3G CELLULAR NETWORK. THE AFFECTED VEHICLES ARE EITHER CURRENTLY IN RETAILER INVENTORY OR ASSIGNED AND IN TRANSIT TO THE RETAILER. INFINITI REQUESTS THESE VEHICLES BE UPDATED PRIOR TO SALE TO ENABLE CLIENTS TO ACCESS AVAILABLE INFINITI CONNECTION FEATURES, INCLUDING AUTOMATIC COLLISION NOTIFICATION AND EMERGENCY CALLING. THERE ARE APPROXIMATELY 142 Q50 VEHICLES IN RETAILER INVENTORY THAT ARE EQUIPPED WITH TELEMATICS CONTROL UNITS DESIGNED TO CONNECT TO THE 2G CELLULAR NETWORK. HOWEVER, THE HARDWARE UPGRADE SERVICE PROCEDURE IS NOT AVAILABLE AT THIS TIME. PLEASE DO NOT TAKE ANY ACTION AT THIS TIME ON Q50 VEHICLES THAT ARE EQUIPPED WITH A 2G-COMPATIBLE TELEMATICS CONTROL UNIT. FURTHER INSTRUCTIONS WILL BE PROVIDED AT A LATER DATE FOR THE TCU UPGRADE ON AFFECTED Q50 VEHICLES. INFINITI EXPECTS THIS COMMUNICATION TO OCCUR IN LATE SUMMER 2016. IMPORTANT: RETAILERS ARE REQUESTED TO INSTALL A 3G-COMPATIBLE TELEMATICS CONTROL UNIT IN VEHICLES AFFECTED BY THIS SERVICE ACTION PRIOR TO RETAIL TO ENSURE CLIENT SATISFACTION."

Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.

trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.

ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.