2018 Infiniti Q50 TSBs

Therefore, INFINITI is conducting a warranty extension to Full Useful Life (FUL) of 10 years or 120,000 miles, whichever occurs first, if white smoke or oil leak occurs with MIL-On condition that requires replacement of the turbocharger assembly on model year 2016-2018 Q50 and model year 2017-2018 Q60. All other warranty terms, limitations, and conditions remain unchanged. On some model year 2016-2018 INFINITI Q50 and 2017-2018 Q60 vehicles there is a possibility that the turbocharger bearing may leak engine oil internally due to premature wear. The internal turbocharger oil leak may cause one or more of the following: Excessive smoke from the exhaust, Service Engine Soon (MIL) light and in severe cases, lack of engine power or damage to the internal components of the turbocharger. During the limited emission warranty extension period, owners are eligible for free replacement of the Turbocharger if it is determined to be required by an INFINITI trained technician. Owners of eligible vehicles will receive notification of this limited emission warranty extension during February 2025. ***** What Retailers Should Do ***** 1. Verify if vehicles are eligible for this Warranty Extension using the warranty extension page of Service Comm. Then, proceed with the instructions in item (2) below. 2. If a client contacts the retailer with a Turbocharger concern in an owned or leased vehicle, retailers should use the Electronic Service Manual (ESM) and appropriate Technical Service Bulletins (TSB) to diagnose the root cause of the customer concern and identify the correct repair to resolve the customer concerns. NOTE: Retailers will need to follow the warranty process and obtain pre-approval when the repair cost exceeds a Retailers Claims Administration/Authorization Limits (DCAL). CONFIRM: With the vehicle at operating temperature excessive smoke from exhaust, the Service Engine Soon (MIL) light on (with DTC P0106) due to excessive oil in the intake system from a turbocharger, or other damage to the turbocharger due to unusual bearing P4A05/P4A06 | Original Document wear and oil leakage. Proceed to replace the affected turbocharger(s) and update the vehicle to the latest engine software.

ACTION 1. Replace the affected turbocharger(s). Refer to the SERVICE PROCEDURE in this bulletin for the updated procedure. IMPORTANT: You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. 2. Refer to step 212 in the SERVICE PROCEDURE to confirm if the ECM needs to be reprogrammed. 2016-2024 Q50 and 2017-2021 Q60 will require ECM reprogramming at the end of this SERVICE PROCEDURE. 3. If the ECM part number is in Table A (page 61 and 63), reprogram the ECM. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

ACTION Replace the engine room sub-harness. Refer to the SERVICE PROCEDURE in this bulletin. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Voluntary Emissions Recall Campaign on certain MY2016-2019 INFINITI Q50 and MY2017-2019 INFINITI Q60 vehicles to reprogram the Engine Control Module (ECM). The ECM reprogram is intended to improve the Idle Stop/Start functionality after 250,000 starter operations. Affected vehicles are subject to stop sale. ***** What Retailers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Recall Campaign using Service Comm or DBS National Service History Open Campaign I.D. R22D1 Refer to IPSB15-286 for additional information. 2. Retailers must not sell, lease, trade, rent or loan any vehicles in retailer inventory affected by this recall campaign until after the vehicle has been remedied. 3. Retailers should use ITB23-017 to remedy any vehicles subject to this campaign. 4. Once remedied, retailers should submit the claim using the claims coding provided and release the vehicle.

this voluntary emissions recall campaign on certain specific model year 2016-2019 Q50 and 2017-2019 Q60 vehicles. The Engine Control Module (ECM) will be inspected, and if necessary, reprogrammed and configured. This service will be performed at no charge to the client for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification number R22D1 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. RETAILER RESPONSIBILITY It is the retailers responsibility to check Service COMM or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) clients and vehicles in a retailers inventory. Federal law requires that new vehicles in retailer inventory which are the subject of an emissions recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration. While federal law applies only to new vehicles, Infiniti strongly encourages retailers to correct any used vehicles in their inventory before they are retailed.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

refer to the SERVICE PROCEDURE in this bulletin for the updated procedure. IMPORTANT: You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. 2016-2017 Q50 and 2017 Q60 will require an ECM reprogramming at the end of this SERVICE PROCEDURE for Turbocharger Exhaust Gas Temperature Sensor deletion. Refer to ITB17-050.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

No other changes were made. Please discard previous versions of this bulletin.

UP/CIRCUIT) is stored, And The customer stated the vehicle was recently started after sitting for an extended period of time (i.e., the battery voltage was low while attempting to start the engine). ACTION 1. Test the vehicles 12 volt battery using the Midtronics DSS-5000. Recharge or replace the battery if necessary. 2. Erase all DTCs.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

water pump and on the water pump pulley AND Coolant DOES NOT leak out when connected to a cooling system pressure tester. HINT: The customer may state there is a coolant smell. ACTION Install an EPT sealer to the face of the water pump pulley. For EPT sealer installation, see SERVICE PROCEDURE on the next page. For EPT sealer information, see PARTS INFORMATION on the last page of this bulletin.

Please see AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

wheels and TPMS sensors (tire pressure sensors) installed. AND The owner states that one or more tires has a continuous air leak or looses air pressure multiple times over a 30 day period (approximatively 1 psi every 3 days). NOTE: The TPMS warning lamp may be ON (not flashing) with one or more of the following DTCs stored: - C1704, C1705, C1706, C1707, C1730, C1731, C1732, C1733 - If the TPMS warning lamp is flashing for more than one (1) minute this bulletin does not apply. Refer to the Electronic Service Manual (ESM) for further diagnostic information. ACTION 1. Confirm that air is leaking between the tire pressure sensors valve stem and valve nut of the affected wheel/tire. 2. Replace the valve stem washer/seal and the valve nut and then torque to the new specification.

VR30DDTT engine has increased by 0.5 quarts (0.5 liters). When replacing a VR30DDTT short block or long block in an applied vehicle for any reason, replace the dipstick with the part listed in PARTS INFORMATION on the next page. The length of the new dipstick is shorter so that it can accurately measure the new oil fill volume. - If the overall length of the dipstick is approximately 25 inches (63.5 cm), replace the dipstick with the one listed in PARTS INFORMATION on the next page. - The overall length of the new dipstick is approximately 24 inches (62 cm). - The new dipstick reflects an increase in oil fill volume by 0.5 quarts (0.5 liters).

INFINITI is conducting a Voluntary Emissions Service Campaign on approximately 49,497 specific INFINITI vehicles identified in Service Comm and currently registered to owners in the state of California to reprogram the Engine Control Module (ECM) in the event that a permanent diagnostic trouble code (P-DTC) for P0448, P0101, P2008, or P0087 is recorded in the ECM. Due to calibration errors on the affected vehicles, the ECM may improperly store a permanent diagnostic trouble code (P-DTC) even though the emissions on-board diagnostic system is functioning properly. As of July 1, 2019 the State of California has implemented a revised Inspection Maintenance (I/M) or Smog Check test program. Without the software update, the subject vehicles may not pass this Smog Check test in those areas of California where such testing is required under state law. This incident has no effect on the safety, performance, drivability, or fuel consumption of the applicable vehicles. ***** What Retailers Should Do ***** 1. Verify if vehicles are affected by this Voluntary Emissions Service Campaign using Service Comm or DBS National Service History Open Campaign I.D. P9329 Affected Model Year 2015 P9344 Affected Model Year 2016 P9346 Affected Model Year 2017 P9348 Affected Model Year 2018 P9350 Affected Model Year 2019 2. Retailers are requested to repair any affected vehicles in retailer new or pre-owned inventory to ensure client satisfaction. - New vehicles in retailer inventory can also be identified DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to IPSB 15-286 for additional information 3. Retailers should use ITB19-043 to correct any vehicles subject to this campaign.

is conducting this voluntary emissions service campaign on certain specific model year Infiniti vehicles (see APPLIED VEHICLES) registered in the state of California. The engine control module (ECM) will be inspected, and reprogrammed if it applies. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification numbers P9329, P9344, P9346, P9348, and P9350 to this campaign. The correct number must appear on all communication and documentation of any nature dealing with this campaign. RETAILER RESPONSIBILITY Retailers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a retailers inventory.

installing an engine oil drain plug on an APPLIED VEHICLE with a VR30DDTT (V6) engine, NEVER tighten the drain plug greater than its specified torque. Over-tightening may loosen the threaded insert in the oil pan (lower), causing an oil leak. ALWAYS replace the drain plug gasket after removing the drain plug, and then tighten the drain plug to the specified torque. VR30DDTT (V6) engine oil drain plug torque (with new gasket): 2WD and AWD: 33.5 Nm (3.4 kg-m, 25 ft-lbs) Avoid contact with the engine oil as it may be hot and cause burns. Avoid prolonged or repeated contact with used engine oil as it may cause skin cancer. Try to avoid direct skin contact with used engine oil. If skin contact is made, wash with a suitable hand cleaner or soap as soon as possible.

or more of the following DTCs stored: C1708 [NO DATA] FL C1709 [NO DATA] FR C1710 [NO DATA] RR C1711 [NO DATA] RL ACTION 1. Verify that the TPMS sensor associated with the stored DTC(s) is transmitting a signal with the Signal Tech II. 2. If transmitting, clear TPMS DTCs, turn the HVAC to maximum cool, and then road test the vehicle (see the specific conditions under steps 20 and 21 on page 6). 3. If a DTC is stored during the road test, replace the HVAC blower motor.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

stored: - C1BA0-00 - (CHASSIS CONTROL BRAKE SYSTEM) - C1B90-00 - (DIRECT ADAPTIVE STEERING SYSTEM) - C1B92-00 - (BRAKE CONTROL SYSTEM) - C1B93-00 - (ENGINE/HEV SYSTEM) - C1B94-00 - (TRANSMISSION SYSTEM) And One or more additional DTCs, other than those above, are also stored in a control unit other than the Chassis Control Module. - Perform the diagnostic/repair procedures for the additional DTCs of the other control unit FIRST. - Refer to the Electronic Service Manual (ESM) for DTC specific diagnostic information. Do not replace the CHASSIS CONTROL MODULE (CONTROLLER ASSY-IDM) if additional DTCs are present.

See Amendment History on the last page. Please discard previous versions of this bulletin.

diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.

vehicles equipped with a 2.0L Turbo Gasoline Engine. INTRODUCTION Infiniti is conducting this voluntary service campaign on certain specific model year 2016-2018 Q50 and 2017-2018 Q60 vehicles equipped with the 2.0L turbo gasoline engine to replace the low pressure fuel line. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification number P8314 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This include vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer?s inventory.

***** Retailer Announcement ***** INFINITI is conducting a Voluntary Service Campaign to replace the low-pressure fuel hose on 15,617 specific MY2016-18 INFINITI Q50 (V37) and MY2017-18 INFINITI Q60 (CV37) vehicles equipped with M274 2.0L engines. The low-pressure fuel hose connected to the fuel pump may not meet INFINITI design specifications. As a result, a small amount of fuel may seep out at the clamped portion under cold temperature and cold engine conditions leading to a detectable fuel smell. ***** What Retailers Should Do ***** 1. Verify if vehicles are affected by this service action using Service Comm or DBS National Service History ? Open Campaign I.D. P8314 - New vehicles in retailer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). - Refer to IPSB 15-286 for additional information - Please continue to check newly arriving inventory for service action applicability. 2. Retailers should use campaign bulletin ITB18-024 to replace the low-pressure fuel hose on affected vehicles. 3. The service department should submit the applicable warranty claim for the action performed so it can be closed on Service Comm and release the vehicle.

No other changes were made. Please discard previous versions of this bulletin.

SERVICE INFORMATION Diagnostic information in the Electronic Service Manuals (ESM) for the following DTCs may be missing or incorrect: -B2EF0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD) -B130C ? TCU (Telematics Control Unit) PAIRING ERROR If one of these DTCs is stored, follow the steps listed below along with the Electronic Service Manual (ESM) to compete the required repairs. DTC B2FE0 ? INTERNAL BATTERY (CIRC VOLT BELOW THRESHOLD): 1. Start the engine and let it idle for 30 minutes (to allow charging of the TCU internal battery). 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. DTC B130C: 1. Collect all keys, and then re-register them to the vehicle. 2. Verify the DTC can be erased. 3. If the DTC will not erase, replace the TCU. NOTE: The related Electronic Service Manuals (ESM) will be updated at a later date. CLAIMS INFORMATION Refer to the current Infiniti Warranty Flat Rate Manual and submit a claim for the repairs performed.

vehicles equipped with VR30DDTT V6 engine. SERVICE INFORMATION Whenever either or both charge air coolers (intercooler) on an applied vehicle?s VR30DDTT V6 engine is removed and reinstalled/replaced for any reason, make sure to properly bleed the charge air cooler (intercooler) cooling system. Use the SERVICE PROCEDURE in this bulletin for the proper intercooler cooling system bleeding. - The procedure in this bulletin is different than what is currently in the Electronic Service Manuals (ESMs). - The ESMs will be updated at a later date. CAUTION: If the intercooler cooling system bleeding procedure in this bulletin is not used: - Damage may occur to the intercooler electric water pump(s), AND/OR - One or more of the following DTCs may set: - P14A2, P14A3, P14A4, P14A5, P14A6, P14A7, P14A8, P14A9 - P14AA, P14AC P14AD, P14AE, P14AF - P14B0, P14B1, P14B2, P14B3, P14B5

The Engine Control Module (ECM) will be reprogrammed so that in the event of an automatic transmission diagnostic issue, the diagnosis signals will be communicated properly and a Malfunction Indicator Light (MIL) will be properly illuminated to notify the driver. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Infiniti has assigned identification number R1726 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY It is the dealer?s responsibility to check Service Comm or Dealer Business Systems (DBS) National Service History for the campaign status on each vehicle falling within the range of this voluntary emissions recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer?s inventory.

The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

2015-2018 Q50 Hybrid (HV37) 2017-2022 Q60 (CV37) 2015-2019 Q70 (Y51) 2015-2018 Q70 Hybrid (HY51) 2019-2024 QX50 (J55) 2022-2024 QX55 (FJ55) 2015-2021 QX60 (L50) 2022-2024 QX60 (L51) 2015-2019 QX60 Hybrid (L50H) 2015-2024 QX80 (Z62) SERVICE INFORMATION The AEB system is designed to turn itself OFF during driving conditions (e.g., rain, snow, fog, etc.) that obstruct its sensors. This behavior is normal, and no repairs should be performed. When the AEB system performs an intentional shutdown, the customer may state the following: The ICC stopped working while driving, The AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), The message Unavailable Front Radar Obstruction or Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owners Manual

Please discard previous versions of ITB17-050.

cannot be performed, (continued on the next page)D

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

SEN/CIRCUIT-B1) and/or DTC P010B (MAF SEN/CIRCUIT-B2) is stored in the ECM on an APPLIED VEHICLE, follow the information in this bulletin along with the ESM to complete the required repairs.

has been diagnosed as sending an incorrect level signal, and one or more of the following DTCs are stored in the ECM, do not replace the entire Fuel Level Sensor Unit, Fuel Filter and Fuel Pump Assembly (fuel pump assembly). The fuel level sensor can be replaced separately. P0460 (FUEL LEV SEN SLOSH) P0461 (FUEL LEVEL SENSOR) P0462 (FUEL LEVL SEN/CIRC) P0463 (FUEL LEVL SEN/CIRC) NOTE: Warranty claims referring to fuel level issues that result in the replacement of the entire fuel pump assembly will be charged back.

quick charge function, the ignition should never be ON, or turned ON, while charging. Attempting to start the vehicle, or turning the ignition ON, while using the high amperage quick charge could potentially damage the fuel pump control module. Only turn the ignition ON when either the ESM or a technical service bulletin service procedure states to do so, and only while using a battery maintainer or smart charger set to reflash mode, or a similar setting. Battery voltage should not exceed 16V during a reprograming operation.

safety, security and satisfaction of our clients and is conducting a quality review of specific repairs for a previously completed campaign (R1912). If the VIN displays QA campaign ID PC838, retailers should perform the procedure attached to this communication even if the National Service History indicates the remedy action was previously performed for the vehicle. VINs identified with this QA campaign ID are being inspected to ensure the recall remedy was performed and documented in accordance with INFINITIs quality standards. ***** What Retailers Should Do ***** PLEASE FOLLOW THE ATTACHED PROCEDURE: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History Open Campaigns I.D. PC838. 2. Retailers should complete this action on both retailed vehicles and previously owned vehicles within retailer inventory. Retailers should follow all stop sale and do not drive, loan, sell, or trade instructions for campaigns. 3. Retailers will need to file the appropriate claim using applicable Op Code information in the repair procedure attached to this announcement to close the campaign. NOTE: Parts replaced under this activity will be placed on parts return. Monitor the Warranty Parts Return Website located at NNAnet.com for notifications.

security and satisfaction of our clients and is conducting a quality review of specific repairs for a previously completed campaign (R1717). If the VIN displays QA campaign ID PC836, retailers should perform the procedure attached to this communication even if the National Service History indicates the remedy action was previously performed for the vehicle. VINs identified with this QA campaign ID are being inspected to ensure the recall remedy was performed and documented in accordance with INFINITIs quality standards. ***** What Retailers Should Do ***** PLEASE FOLLOW THE ATTACHED PROCEDURE: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History Open Campaigns I.D. PC836. 2. Retailers should complete this action on both retailed vehicles and previously owned vehicles within retailer inventory. Retailers should follow all stop sale and do not drive, loan, sell, or trade instructions for campaigns. 3. Retailers will need to file the appropriate claim using applicable Op Code information in the repair procedure attached to this announcement to close the campaign. NOTE: Parts replaced under this activity will be placed on parts return. Monitor the Warranty Parts Return Website located at NNAnet.com for notifications.

security and satisfaction of our clients and is conducting a quality review of specific repairs for a previously completed campaign (P8314). If the VIN displays QA campaign ID PC832, retailers should perform the procedure attached to this communication even if the National Service History indicates the remedy action was previously performed for the vehicle. VINs identified with this QA campaign ID are being inspected to ensure the service campaign remedy was performed and documented in accordance with INFINITIs quality standards. ***** What Retailers Should Do ***** PLEASE FOLLOW THE ATTACHED PROCEDURE: 1. Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History Open Campaigns I.D. PC832. 2. Retailers should complete this action on both retailed vehicles and previously owned vehicles within retailer inventory. 3. Retailers will need to file the appropriate claim using applicable Op Code information in the repair procedure attached to this announcement to close the campaign. NOTE: Parts replaced under this activity will be placed on parts return. Monitor the Warranty Parts Return Website located at NNAnet.com for notifications. ***** Retailer Responsibility ***** It is the retailers responsibility to check Service Comm or DBS National Service History - Open Campaign using the appropriate campaign I.D. for the status of each vehicle currently in retailer inventory or entering the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners. If a VIN subject to this quality action was traded to another retailer, please notify the affected retailer to have this quality action and associated campaign(s) completed.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

sensitive AND There are no EPS DTCs stored. ACTION 1. Confirm the current power steering control module part number. 2. Reprogram the power steering control module, if applicable.

values in Table A on page 4 must be used. For all other models, consult the Electronic Service Manual (ESM). The following CONSULT-III plus (C-III plus) figures and steps are only provided to indicate where the VEHICLE REFERENCE VALUE from Table A is to be entered. The entire camera aiming procedure must be followed to complete the aiming procedure. Refer to the Electronic ESM section: CRUISE CONTROL & DRIVER ASSISTANCE > DRIVER ASSISTANCE SYSTEM > DRIVER ASSISTANCE SYSTEM > BASIC INSPECTION > LANE CAMERA UNIT > CAMERA AIMING ADJUSTMENT. 1. Turn the ignition ON. 2. From the C-III plus home screen, select Diagnosis (One System).

in Table A on page 2, AND The ECM part number is shown in Table B, starting on page 3. ACTION 1. First perform the appropriate diagnostic procedure for the stored DTC to repair the vehicle according to the Electronic Service Manual (ESM). 2. Reprogram the ECM after performing the diagnosis and repair. -The ECM reprogram in this Service Procedure is not a repair for the DTC, but instead updates the way the permanent DTC is stored and allowed to be erased. The DTC must be properly diagnosed and repaired before the reprogram is applied.

reset cannot be performed And The following screen will display: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. Refer to SERVICE PROCEDURE on the next page. HINT: OCS may also be referred to as ODS. 2. Perform 75-zero RESET.

RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.

flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.

See Amendment History on the last page. Please discard previous versions of this bulletin.

tool to the Service > Campaign screen: Retailed Vehicle Open Campaign Report on July 9, 2018, which identifies owner contact information for specific campaigns. Currently, only Takata campaign owner lists are available. The following personnel will have access to this tool: - Retailer: Dealer Principal, Executive Managers, General Managers, Parts/Service Managers, and/or Parts/Service Directors - Regions: Regional Aftersales Manager (RAM), Regional Operations Managers (ROM), Fixed Operations Manager (FOM), Dealer Operation Managers (DOM), Regional Service Operation Managers (RSOM), and Client Experience Managers (CEM) The report can be viewed on screen or exported to Microsoft Excel and identifies the following: - VIN - Campaign ID & Campaign Description - Model & Model Year - Data Source o Up to three data sources can be provided for each VIN - RO Info: If this VIN has visited an Infiniti retailer anywhere in the U.S. within the last twelve months, the RO information will be displayed. - Campaign Mailing List: This is DMV data for the VIN listed - Marketing List: If an owner is on your marketing list, their contact information from that list will be displayed here. DMV data is not used for marketing list owner information. - Contact Name - Last Name/First Name & Address (City, State, Zip) - Phone (1-3) & Email (1-3) - Remove Flag o This defaults to ?N? unless the retailer or INFINITI USA flags this VIN for removal. o The removed information will still show on the DBS screen and exported report, but can be filtered on the exported file to only display the records with ?N? in this column.

to the Service > Campaign screen: Custom VIN Campaign Report. The tool identifies open campaigns on a customized VIN list loaded into DBS for INFINITI and Nissan vehicles. The following personnel will have access to this tool: - Retailer: Executive Managers, Service Managers, and/or Service Directors - Regions: Regional Aftersales Manager (RAM), Area General Manager (AGM), Fixed Operations Manager (FOM), Regional Service Operation Managers (RSOM), and Retailer Technical Specialist (DTS) The VINS can be loaded individually or up to 10,000 VINs at a time. If you have more than 10,000 VINs, each incremental VIN file of 10,000 or less VINs will need to be loaded prior to selecting the Check For Open Campaigns option. The report can be viewed on screen or exported to Microsoft Excel and will identify the following for each VIN loaded into the tool: - Open Campaigns (ID and description) - Model Code, Model, and Model Year - Current Repair Status Blank: Repair order (RO) has not been opened yet Unrepaired: RO has been opened for the campaign, but not closed or submitted o Repaired: RO for the campaign has been closed and a warranty claim has been submitted - Current Claim Status o Blank: RO still open o Unsubmitted: A warranty claim for the campaign repair has not been submitted o Submitted: A RO has been closed and a campaign warranty claim has been submitted for payment o Suspended: The campaign warranty claim has suspended for one or more errors o Rejected: The campaign warranty claim has been denied for some reason (by retailer or NNA) o Paid: A campaign warranty claim has been submitted and paid by NNA, but the vehicle has not yet been removed from the NNA open campaign vehicle table - Stop Sale Applicability - Parts Restriction Applicability (If restricted, SVC order must be used to acquire parts)

Please discard all previous versions of this bulletin.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. Please discard previous versions of ITB23-010.

To access infotainment software updates via the Infotainment Software Update Utility: Select SPECIALTY TOOLS, and then select Infotainment Software Updates on the left side of ASIST. HINT: Initially, the Infotainment Software Update Utility will be available only on the CONSULT PC version of ASIST. The Utility will be added to ASIST WEB at a later date. Please discard previous versions of ITB23-010.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

replacement of the AV Control Unit, it is necessary to verify the current software version of the AV Control Unit to determine if a software version update is required. Use the vehicle tables in this bulletin to determine the current software version, if the AV Control Unit requires a software version update, and which procedure to use to update the AV Control Unit. The software updates in this bulletin are to address stability improvements and bug fixes. IMPORTANT: If the client is experiencing a software related concern, refer to ITB21-011 to verify if the client concern is a hardware or software related issue. If the concern is a software related issue, review the information in this bulletin to update the AV Control Unit as needed.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Please see Amendment History on the last page. Please discard previous versions of this bulletin.

Please see Amendment History on the last page. Please discard previous versions of this bulletin.

Unit (DCU) needs to be replaced on an APPLIED VEHICLE for any reason, follow the steps in the Service Procedure to: - Confirm proper diagnosis and repair with TECH LINE to obtain DCU order approval, then place the order with DENSO. NOTE: The DCU order approval process does not apply to 2017 model year and earlier models. TECH LINE authorization is not needed for 2017 model year and earlier models. - Configure the Multi AV system. - 2018-2019 QX30 vehicles only: Register the replacement DCU. DCU registration is necessary whether or not the vehicle has an active Infiniti InTouch Apps subscription. NOTE: The original DCU must be installed in the vehicle while performing part of this procedure. DO NOT remove the original DCU until instructed.

This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.

This bulletin has been amended to add a Required Actions by Model and Year table on page 2, a Check OFF Sheet on page 21 and to reorganize the information throughout. It is necessary for you to read this revised procedure to properly perform this Service Information. Please discard previous versions of this bulletin.

Services Voice Menu, Destination Assistance does not download Point Of Interest (POI) successfully. NOTE: The lower screen will then display the error message in Figure 1. ACTION Manually configure MULTI AV using CONSULT-III plus (C-III plus).

The Applied Vehicles section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. Changes have been made throughout. You must read the entire bulletin to understand all the changed information. Please discard all previous versions of this bulletin.

The Applied Vehicles section and Part 1 of the Service Procedure have been revised. No other changes have been made. Please discard previous versions of this bulletin.

This bulletin has been amended. Information for several 2018 models has been added. No other changes have been made. Please discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

SERVICE INFORMATION If the AEB warning light is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: - When contamination or foreign material adhere to the lane camera viewing window on the windshield - When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield - When the lane camera viewing window on the windshield is temporarily fogged up NOTE: - If DTCs are present in any of the following related systems: - Laser/Radar, - ICC/ADAS, or - Lane Camera, Refer to the related Electronic Service Manual (ESM) for diagnosis. - Refer to the following pages for further information.

occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.

This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

warranty information on page 2 has been updated. No other changes have been made. Please discard previous versions of this bulletin.

Also, warranty information on pages 1 and 8 has been updated. No other changes have been made. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

installed SOS switch, located near the overhead map lamp, also come equipped with a wireless communication device called a Telematics Communication Unit (TCU). AT&T discontinued its U.S. 3G network coverage on February 22, 2022. As a result, automakers that utilize AT&Ts 3G network connection, including Nissan Group, have had connectivity services affected. INFINITI Connection with InTouch Services are no longer available on the APPLIED VEHICLES listed above.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

installed or VPC installed accessories. SERVICE INFORMATION The National Highway Traffic Safety Administration (NHTSA) requires that any automobile dealer that installs accessories on a vehicle prior to first retail sale must install a special label (?reduced capacity label?) on that vehicle if the total weight of all accessories on that vehicle exceeds 1.5 percent of the vehicle?s gross vehicle weight rating (GVWR) or 100 pounds, whichever is less. This includes accessories that the dealer installs (dealer installed factory accessories and dealer installed aftermarket accessories), and accessories installed at the Vehicle Processing Center (VPC) prior to the vehicle being delivered to the dealer. IMPORTANT: Failure to comply with this requirement may result in penalties imposed by NHTSA. Follow the instructions in this bulletin to help meet these requirements.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Please see AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

This bulletin has been amended to correct a DTC listed in the SERVICE INFORMATION. No other changes have been made. Discard all previous versions of this bulletin.

The Applied Vehicles section has been revised. No other changes have been made. Please discard previous versions of this bulletin.

A correction was made to the Service Procedure on page 15. No other changes were made. Please discard previous versions of this bulletin.

SERVICE INFORMATION When replacing or adding an Intelligent Key, it is very important to make sure the correct Intelligent Key is selected from the parts department. - A running change was made that will help identify the correct Intelligent Key. - Beginning in late 2017 and early 2018 the last five digits of the Intelligent Key part number is marked on the Intelligent Key under the mechanical key. - See page 2 for location images of this part number addition. NOTE: - A correct Intelligent Key may or may not have the last five digits of the part number as shown on page 2. - The above running change was applied as a ?help? to identify the correct Intelligent Key for a given vehicle, but the actual part number listed in the parts catalog did not change. - Make sure to use the electronic parts catalog (FAST) or equivalent to confirm the correct Intelligent Key for a given vehicle.

The announcement from June 10, 2023 has been revised to include the following: INFINITI has expanded the investigation of a potential issue with the repair remedy to include model years 2018-2019 Q50 and Q60 vehicles. Repairs on all vehicles are temporarily suspended while INFINITI investigates the remedy. As a result, all vehicles affected by this campaign will be temporarily deactivated in Service Comm and National Service History. An update will be provided at a later date If there are claim processing concerns, email the FQA mailbox: FQA_Inspection_Support@nissan-usa.com

The announcement from May 5, 2023 has been revised to include the following: INFINITI is investigating a potential issue with the repair remedy for model years 2016-2017 Q50 and Q60 vehicles. As a result, these affected vehicles will be temporarily deactivated in Service Comm and National Service History. Repairs on these vehicles are temporarily suspended while INFINITI investigates the remedy. An update will be provided at a later date If there are claim processing concerns, email the FQA mailbox: FQA_Inspection_Support@nissan-usa.com

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

P0174 (FUEL SYS LEAN B2) have been revised for the APPLIED VEHICLES listed above. When performing diagnosis for either of these DTCs, start by using the SERVICE PROCEDURE section of this bulletin. NOTE: The related Electronic Service Manuals (ESM) will be revised in the future to include these diagnostic steps.

applied vehicle: - Reverse camera is blank (vehicles manufactured before May 1, 2018) - Reverse camera remains ON when in Drive (vehicles manufactured before May 1, 2018) - Average fuel economy displays 99.9 MPG - Display screen flickers at higher ambient interior temperatures - SXM Info Apps (Weather, Stocks, Fuel Prices) inoperative ACTION 1. Refer to page 4, step 8 in the SERVICE PROCEDURE to confirm an update applies to the Display Control Unit (DCU) of the vehicle being worked on. - Confirmation is determined by comparing the DCU part number with those listed in Table on page 5. 2. If this bulletin applies, update the DCU software. - See REQUIRED SPECIAL TOOL on page 2. NOTE: The updated software resolves the items above along with improving software stability.

See Amendment History on the last page. Please discard previous versions of this bulletin.

The publication date has been revised to include the latest models and model years, and the Service Procedure has been updated. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

are stored, make sure to follow the diagnostic procedures in the Electronic Service Manual (ESM) before replacing any parts. C1A03 ? VEHICLE SPEED SENSOR -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1A04 ? ABS/TCS/VDC SYSTEM -The diagnostic procedure in the ESM includes check and, if needed, repair for ABS DTCs before replacing ADAS components. -If repairs are performed for the ABS system; when compete, perform DTC Confirmation Procedure again before doing any additional repairs. C1B01 CAM AIMING INCMP -The diagnostic procedure in the ESM includes check and, if needed, repair for LANE CAMERA DTCs before replacing ADAS components. -LANE CAMERA DTC may require adjustment of the lane camera. -If repairs/adjustments are performed for the Lane Camera; when compete, perform DTC Confirmation Procedure again before doing any additional repairs.

Also, tips for using the ProCut? brake lathe were added on page 8, and a Brake Noise Diagnostic Worksheet was added on page 10. Please discard previous versions of this bulletin.

The APPLIED VEHICLES were updated with new models and model years. No other changes have been made. Discard previous versions of this bulletin.

Changes have been made throughout. It is necessary to read the revised procedure(s) in entirety to properly perform the action(s). Please discard previous versions of this bulletin.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

ACTION Follow the SERVICE PROCEDURE in this bulletin to reprogram the TCM.

found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (cv Joint Boot Kit) availability. If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the retailer. If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to ITB21-002 to prevent Drive Shaft thread damage.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

equipped with INFINITI InTouch (Intelligent Key). SERVICE INFORMATION An Intelligent Key, for the applied vehicles with INFINITI InTouch?, has the abillity to trigger specific customized settings for the radio, clock, heating and air conditioning (HVAC) and navigation that are unique to that key, and each Intelligent Key for a specific vehicle may have different settings stored. EXAMPLE: The vehicle may be driven by more than one person, and each driver has a personal Intelligent Key. Each driver may adjust their preferred vehicle settings differently. If two or more Intelligent Keys with different stored settings are unintentionally interchanged, one or more of the following perceived issues might be reported by the customer(s). - Radio ? Presets are lost or change - Clock ? Settings are not showing the correct time due to day-light savings or the selected region (time zone) - HVAC ? Controls are set differently - Navigation ? Settings suddenly altered If any of these perceived issues are present: - Confirm if there are multiple Intelligent Keys being used by the customer(s) interchangeably, and if so, verify that each key?s settings are different. NOTE: Customer may not recognize that different Intelligent Keys are linked differently.

trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.

equipped with Direct Adaptive Steering (DAST). SERVICE INFORMATION This bulletin has information for two services for which a technician may need additional help: - While performing DAST CALIBRATION (MODE1), the calibration may stop or will not start. - DTC C13E9-00 (BOOTING ANGLE PROCESSING) and C13EB-00 (BOOTING ANGLE PROCESSING) are stored and cannot be erased. The above conditions may indicate that DAST CALIBRATION (MODE1) was not performed correctly or was not completed correctly. Use the SERVICE PROCEDURE in this bulletin as an aid to correctly perform and complete DAST CALIBRATION MODE 1. NOTE: - The SERVICE PROCEDURE in this bulletin does not contain all of the required steps. - The Electronic Service Manual (ESM) must be used together with this bulletin. - This bulletin contains additional clarification as an aid to perform DAST CALIBRATION MODE 1.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.