2010 Infiniti G37 TSBs

(LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.

- Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.

As with previous BCM replacements, when a blank unit is installed, the configuration process must be performed. See this bulletin for further detail.

Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.

position other than fully closed or fully retracted, the retractable hard top control may stop operating and the following DTCs will be stored: B1707 and B1708. Other retractable hard top related DTCs may also be found stored. To restore operation: (1) close the roof fully manually; (2) erase the DTC(s); and (3) perform hard top control unit initialization. This bulletin provides the procedures to restore retractable hard top control operation. See this bulletin for further detail.

- When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.

This bulletin gives an outline of the retailer technician?s responsibilities in assisting the retailer claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.

"RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.

The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulletin for further details.

following issue may occur - When the driver door is opened, the convertible top opens. When replacing a BCM, make sure to - Follow information in the appropriate Service Manual - Use CONSULT-III plus to perform configuration - Select the correct vehicle in CONSULT-III plus - Confirm the VIN is correct (matches the vehicle) in CONSULT-III plus - Select/install the correct configuration

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Please discard previous versions of ITB15-024.

Discard previous versions of ITB15-019.

tool to the Service > Campaign screen: Retailed Vehicle Open Campaign Report on July 9, 2018, which identifies owner contact information for specific campaigns. Currently, only Takata campaign owner lists are available. The following personnel will have access to this tool: - Retailer: Dealer Principal, Executive Managers, General Managers, Parts/Service Managers, and/or Parts/Service Directors - Regions: Regional Aftersales Manager (RAM), Regional Operations Managers (ROM), Fixed Operations Manager (FOM), Dealer Operation Managers (DOM), Regional Service Operation Managers (RSOM), and Client Experience Managers (CEM) The report can be viewed on screen or exported to Microsoft Excel and identifies the following: - VIN - Campaign ID & Campaign Description - Model & Model Year - Data Source o Up to three data sources can be provided for each VIN - RO Info: If this VIN has visited an Infiniti retailer anywhere in the U.S. within the last twelve months, the RO information will be displayed. - Campaign Mailing List: This is DMV data for the VIN listed - Marketing List: If an owner is on your marketing list, their contact information from that list will be displayed here. DMV data is not used for marketing list owner information. - Contact Name - Last Name/First Name & Address (City, State, Zip) - Phone (1-3) & Email (1-3) - Remove Flag o This defaults to ?N? unless the retailer or INFINITI USA flags this VIN for removal. o The removed information will still show on the DBS screen and exported report, but can be filtered on the exported file to only display the records with ?N? in this column.

to the Service > Campaign screen: Custom VIN Campaign Report. The tool identifies open campaigns on a customized VIN list loaded into DBS for INFINITI and Nissan vehicles. The following personnel will have access to this tool: - Retailer: Executive Managers, Service Managers, and/or Service Directors - Regions: Regional Aftersales Manager (RAM), Area General Manager (AGM), Fixed Operations Manager (FOM), Regional Service Operation Managers (RSOM), and Retailer Technical Specialist (DTS) The VINS can be loaded individually or up to 10,000 VINs at a time. If you have more than 10,000 VINs, each incremental VIN file of 10,000 or less VINs will need to be loaded prior to selecting the Check For Open Campaigns option. The report can be viewed on screen or exported to Microsoft Excel and will identify the following for each VIN loaded into the tool: - Open Campaigns (ID and description) - Model Code, Model, and Model Year - Current Repair Status Blank: Repair order (RO) has not been opened yet Unrepaired: RO has been opened for the campaign, but not closed or submitted o Repaired: RO for the campaign has been closed and a warranty claim has been submitted - Current Claim Status o Blank: RO still open o Unsubmitted: A warranty claim for the campaign repair has not been submitted o Submitted: A RO has been closed and a campaign warranty claim has been submitted for payment o Suspended: The campaign warranty claim has suspended for one or more errors o Rejected: The campaign warranty claim has been denied for some reason (by retailer or NNA) o Paid: A campaign warranty claim has been submitted and paid by NNA, but the vehicle has not yet been removed from the NNA open campaign vehicle table - Stop Sale Applicability - Parts Restriction Applicability (If restricted, SVC order must be used to acquire parts)

Please discard all previous versions of this bulletin.

CAUSES THE RAIN SENSOR, WHEN WIPER LEVER IS PUSHED DOWN, TO EITHER MAKE A SINGLE STROKE OR OPERATE UNEXPECTEDLY. NO MODELS OR MODEL YEARS LISTED. *PE

NO MODELS LISTED. MODEL YEARS 1998-2013. *PE

*JS

CHECK THE BATTERY STATE OF CHARGE (SOC) AND RECHARGE IF NECESSARY AND REPROGRAM THE BCM. ALSO INCLUDED MODELS FX35/50 MODEL YEARS 2011-2012. *JS

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

- See page 2 and 3 for specific locations and types of noises. ACTION: Refer to the Repair Overview on page 2 and 3. See this bulletin for further detail.

breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.

off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulleitn for further details.

In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Infiniti vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain,iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.

occur when using a cleaner with too high of an alkaline concentration. - Always refer to the Appearance and care section of the related owner?s manual. - Not all cleaners are created equal. - Many cleaners come in concentrated form. - Alkaline cleaners (cleaners with a high pH value) can cause spots on paint and trim when not used as directed. - Some commercial car washes use cleaners with a high pH value. - When using cleaners that meet the conditions defined in the Appearance and care section, be sure to carefully follow the cleaner?s directions. - When finished cleaning/washing, rinse thoroughly with clean water. IMPORTANT: Damage to paint, glass, bright metal, or any other exterior surface caused by using improper cleaning products is not covered under warranty. Always refer to the Paint Incident Identification Manual (PIIM) and Assurance Products Reference Manual (APRM). Follow the guidelines in the PIIM and APRM for non-warrantable exterior body, glass, or painted surface quality issues. To access the PIIM and APRM, login to nnanet.com: - For the PIIM, select: MY LINKS > Warranty > Paint Incident Identification Manual - For the APRM, select: MY DOCUMENTS > Warranty > APRM See further information in this bulletin.

This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.

warranty information on page 2 has been updated. No other changes have been made. Please discard previous versions of this bulletin.

Also, warranty information on pages 1 and 8 has been updated. No other changes have been made. Please discard previous versions of this bulletin.

weather-strip self-adhesive has detached from the center roof panel. ACTION - Reattach the affected seal with the Service Procedure starting on the page 3.

*PE

THE REAR VIEW MIRROR VIBRATES. THERE IS A BOOMING NOISE HEARD. THE SYMPTOMS GET WORSE AS SPEED INCREASES. 2009-2011 G37. *RM

WATER IN THE EXTERIOR LAMPS. THIS IS GENERALLY NOT DUE TO A DEFECT. ALL CURRENT EXTERIOR LAMP ASSEMBLIES ARE VENTED TO THE ATMOSPHERE (NOT SEALED). MOISTURE IN THE AIR SOMETIMES TRAVELS INTO AND OUT OF THE LAMP ASSEMBLY THROUGH THESE VENTS. NECESSARY TO ALLOW FOR EXPANSION AND CONTRACTION OF AIR FROM TEMPERATURE VARIATIONS (WARMER OR COLDER) WITHOUT DAMAGE TO THE LAMP. CERTAIN ENVIRONMENTAL CONDITIONS MAY CAUSE MOISTURE TO CONDENSE. FOGGING/CLOUDINESS SHOULD DISAPPEAR OVER TIME WHEN THE LAMP IS IN A DRY ENVIRONMENT. *PE UPDATED 7/28/10. *PE UPDATED 12/9/13. *PE

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.

DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.

attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.

Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.

- The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.

* Hesitation/lag when accelerating after coasting. * Hesitation/lag or harsher than expected down shifts when coming to a stop and accelerating again (rolling stop). * Engine rev matching during moderate to heavy braking. ACTION 1. Referto step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM and TCM. See this bulletin for further detail.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

See Amendment History on the last page. Please discard previous versions of this bulletin.

diagnosis and to promote Fixed-Right-First-Time ? Infiniti may review CONSULT-III plus (CIII plus) data relating to vehicle operation and function to help with vehicle diagnosis and diagnostic validation. IMPORTANT: For transmission/engine repair or replacement, retailers are required to connect C-III plus and perform ?Diagnosis (All Systems)?. Performing C-III plus ?Diagnosis (All Systems)? is also required prior to contacting any Infiniti call center (i.e. TECH-LINE, PCC, or WCC) for diagnostic support or claim preauthorization. NOTE: For additional information regarding Automated Vehicle Data Collection, refer to IWBI/18-019. To support Automated Vehicle Data Collection, your C-III plus must have the Diagnosis result reporting function-Setting turned ON. If Diagnosis result reporting function-Setting is OFF: - It may cause dealer consideration for Audit or the Anomalous Repair Control (ARC) program, where applicable. - It may result in a repair being non-warrantable. Refer to the Service Procedure on the next page to confirm your C-III plus ?Diagnosis result reporting function-Setting? is turned ON.

The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.

A SLIGHT VEHICLE VIBRATION/SHUTTER WITH LIGHT ACCELERATION AT LOW SPEEDS; AT TIMES ENGINE RPM GOES UP (ABOUT 200-250 RPM) DURING THE 3RD>4TH UP SHIFT, OR THE 4TH>5TH UP SHIFT; ENGINE BRAKING FEEL IS MORE THAN EXPECTED WITH DECELERATION; THE 2ND>1ST DOWN SHIFT IS HARSHER THAN EXPECTED. *PE UPDATED ON 6/15/2011. *KB

MODELS COUPE, SEDANS AND CONVERTIBLES (G37). *PE

NO APPLIED VEHICLES AFFECTED: ALL MODELS; NO MODEL YEARS LISTED. *PE

Repair orders opened after this bulletins published date are no longer eligible for reimbursement under Campaign ID # P1235. Discard all previous versions of ITB11-046.

Repair orders opened after this bulletins published date are no longer eligible for reimbursement under Campaign ID # P0308. Discard all previous versions of ITB10-015.

The customer goes to www.infinitinavigation.com and is mailed update disc(s) or SD card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.

Control Unit on an Applied Vehicle. Previously, TECH LINE would need to be contacted to confirm (or assist with) diagnosis and the proper repair prior to ordering an A/V control unit. This process has been suspended.

Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.

To remedy this potential condition, Infiniti is conducting this voluntary service campaign to update the navigation software at no charge for parts or labor. In addition, as part of this navigation software update, a call waiting function will be added to the hands-free phone system. See this bulletin for further detail. Campaign ID # P1235

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Discard previous versions of ITB11-066.

for each retailer?s Retailed Vehicle Open Campaign Report has been updated today in DBS. We made our best effort to reassign vehicles to retailers based on the most recent owner information we received. The complexity of filtering out brokers (banks, salvage yards, and insurance companies) and reassigning VINs based on updated owner information affected over 123K records between INFINITI and Nissan, so we are unable to summarize the changes at a regional or retailer level. We suggest the retailers download their lists and have their outbound call centers compare information if necessary. If you have questions, please let us know. Additionally, we will have some enhancements coming in DBS effective November 17, 2018: Owner Data Updates (NNA side): 1. VIN, Campaign Code, and Source are the unique fields 2. Compare all fields except Remove Flag and Comments to see if there is a difference. a. If there is same VIN, Camp ID, and Source and all other fields are also the same then the record will be updated without changing Remove Flag and Comment field b. If there is same VIN, Camp ID, and Source and any other field is different, then the record will be inserted, in this case Remove Flag and Comment field will be blank as this is new record. The remove flag is being removed so the retailer will understand the information they previously flagged for removal has been updated and should be tried again before reapplying the removal flag. c. The retailer benefit of A & B above is duplicate records for the same VIN, Camp ID, and information source with the same customer contact information will no longer display in DBS on the Retailed Vehicle Open Campaign Report.

No other changes have been made. Please discard previous versions of this bulletin.

reboots when SXM Traffic is enabled. NOTE: Perform the steps in this bulletin ONLY if the above condition occurs while the vehicle is in the state of Oregon. ACTION Update the Navigation system software using the DVD shown on page 2.

LOCK/UNLOCK REQUEST BUTTON LOCATED ON OUTSIDE DOOR HANDLES OF VEHICLES CAN BE DISABLED (OR ENABLED) THROUGH EITHER THE "COMFORT & CONV" SETTINGS OF THE AUDIO/VISUAL/NAVIGATION SYSTEM OR THROUGH THE "COMBINATION METER SETTINGS" DEPENDING ON THE VEHICLE MODEL, YEAR, AND TRIM LEVEL. *JS

*PE SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. MODEL 2010-2011 G37, QX56, FX35, FX30, EX35, M37, M56, M35H HYBRID. *PE

2010 INFINITI G37. REPROGRAMMING OF THE NAVIGATION UNIT TO CORRECT THE OPERATION OF THE RADIO SEEK FUNCTION. *RM

A SOFTWARE PROBLEM IS CAUSING THE NAVIGATION, IPOD, AND MOBILE PHONE FUNCTIONS TO BE INOPERATIVE. *RM

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

THE TITLE AND IF YOU CONFIRM SECTION HAVE BEEN REVISED. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN.

longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.

Infiniti vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.

We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.

We are re-circulating this update to make regional and retailer personnel aware that we are re-notifying clients at this time.

The announcement from March 21, 2017 has been revised to include: - Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps - Customer expense may be applicable if the vehicle is out of warranty

announcement from March 21, 2017 has been revised to include: o Clarification that the refueling concern is extremely hard to fill, not intermittent, and occurs at multiple fueling stations and fuel pumps o Client expense may be applicable if the vehicle is out of warranty

Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.

fueling the vehicle at different fuel stations (filling nozzle shuts off every few seconds while filling at multiple stations and using multiple filling pumps). IMPORTANT: - If the customer does not report the above symptoms, this bulletin does not apply. - If the customer reports intermittent (but not consistent difficulty re-fueling), this bulletin does not apply. ACTION: Perform the Inspection Procedure in this bulletin, starting on page 4, only if the customer reports symptoms as described above. NOTE: Refer to the Repair Overview on page 2.

nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.

MODEL YEARS 2007-2011. NO MODELS LISTED. *PE

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM with CONSULT-III plus ONLY. See this bulletin for further detail.

of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Infiniti STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.

provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. See this bulletin for further details.

ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see ITB00-024). See this bulletin for further detail.

Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.

qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.

Also, tips for using the ProCut? brake lathe were added on page 8, and a Brake Noise Diagnostic Worksheet was added on page 10. Please discard previous versions of this bulletin.

MODELS 2007-2013 INFINITI. *PE

These items may be available from Infiniti by request if certain criteria are met. This bulletinlists the criteria and provides an application form for such replacements. See this bulletin for further detail.

See this bulletin for further detail.

All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.

If any of these parts are needed for any reason, order the part(s) using the order form in this bulletin. See this bulletin for further detail.

top should not sink or drop further than 250 mm (9.84 inches) within one (1) minute or less when opened as shown in Figure 1. - If the convertible top sinks further than 250 mm (9.84 inches) within one (1) minute or less - the pump assembly needs to be replaced. - If the convertible top does not sink further than 250 mm (9.84 inches) within one (1) minute or less - the pump assembly is OK. NOTE: This instruction supersedes the previous 15 mm measurement threshold specified in SIR video # 165. CAUTION: The convertible top should only be partially opened for service and should not be left in this position as damage may result. See this bulletin for further detail.

See AMENDMENT HISTORY on this page. Discard all previous versions of this bulletin.

steps in the Service Procedure to configure the Multi AV system. NOTE - The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control Unit until instructed. See this bulletin for further detail.

Customer report may include: Voice is choppy or cuts-out, voice sounds distant, voice sounds as if speaking through a tunnel, and/or voice sounds like it's under water. ACTION 1. Reprogram (reconfigure) the Multi AV. 2. Replace the microphone and the map lamp finisher. See this bulletin for further detail.

Customer report may include: Voice is choppy or cuts-out, voice sounds distant, voice sounds as if speaking through a tunnel, and/or voice sounds like it's under water. ACTION 1. Replace the TEL Adaptor Unit. 2. Replace the microphone and the map lamp finisher. See this bulletin for further detail.

installed or VPC installed accessories. SERVICE INFORMATION The National Highway Traffic Safety Administration (NHTSA) requires that any automobile dealer that installs accessories on a vehicle prior to first retail sale must install a special label (?reduced capacity label?) on that vehicle if the total weight of all accessories on that vehicle exceeds 1.5 percent of the vehicle?s gross vehicle weight rating (GVWR) or 100 pounds, whichever is less. This includes accessories that the dealer installs (dealer installed factory accessories and dealer installed aftermarket accessories), and accessories installed at the Vehicle Processing Center (VPC) prior to the vehicle being delivered to the dealer. IMPORTANT: Failure to comply with this requirement may result in penalties imposed by NHTSA. Follow the instructions in this bulletin to help meet these requirements.

REFER TO THE APPROPRIATE SERVICE MANUAL, FOLLOW THE DIAGNOSTIC AND REPAIR INFORMATION FOR XENON HEADLAMPS. *PE

NO MODELS OR MODEL YEARS LISTED. *PE UPDATED ON 08-11-2011. *KB

depressed to the floor OR the customer states the clutch pedal on an applied vehicle does not return to its normal (rested) position after being depressed to the floor AND there are no leaks in the clutch hydraulic system. ACTION: Flush (remove) ALL existing clutch hydraulic system fluid, and refill with GT-R R35 Special Brake Fluid (see PARTS INFORMATION). - Use the SERVICE PROCEDURE in this bulletin for proper flush and refill procedure. See this bulletin for further detail.

rack, or steering rack) leak issues, in some cases it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. - Go to Power Steering Gear Inspection starting on page 2. See this bulletin for further detail.

ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. >Please see Service procedure for 2007-2011 Versa torque specifications on page 5. See this bulletin for further detail.

*KB

REPROGRAM ECM AND TCM. *JS UPDATED 7/26/12. *PE UPDATED 8/28/12. *PE UPDATED 11/5/12. *PE

APPLIES TO RE 5R05A ONLY TRANSMISSIONS (5 SPEED A/T). IF ONE OR MORE DTCS LISTED ARE FOUND STORED IN SELF DIAGNOSIS, USE THE REPAIR FLOW CHART TO ASSIST IN DIAGNOSIS. *PE

Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90 (see Figure 1). Moving vehicles as shown in this bulletin will prevent tire Flat Spotting. See this bulletin for further detail.

etc.), are specifically developed to achieve Infiniti design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Infiniti's standards. Infiniti Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Infiniti most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletin for further details.

AND ARE SERIOUSLY DAMAGED AND NOT GUARANTEE OR WARRANTY THE MODIFIED WHEELS OR PERFORMANCE. MODELS ALL. NO YEARS LISTED. *PE

*JS

ask its retailers to urgently help increase customer participation in the Takata recalls to help it achieve 100% customer recall participation for the following vehicles: ? 2001 I30 ? 2002-04 I35 ? 2003-08 FX ? 2002-03 QX4 ? 2006-10 M Sedan INFINITI expects to upload the next refreshed owner list to DBS within the next week. We will also be reassigning VINs to retailers based on information changes. We didn?t reassign any VINs in Q2 to avoid any mid-quarter objective impact. If VINs were repaired out of network, the retailer/region with the original assignment received credit for the repair. This is an extremely serious safety issue and INFINITI is taking significant and unprecedented steps to increase client recall participation but it needs retailer help to achieve its remedy goals. A separate communication will be released later this month informing regional personnel of the requirements for bonus payout in Q3 and Q2 results. The Q3 objective is based on the average number of repairs in Q2 multiplied by the number of service days in Q3 (Mon-Sat minus any holidays). Retailer engagement is critical with this effort. It is a company-wide responsibility to make it a priority to replace these dangerous airbag inflators in affected vehicles. Further, increasing recall participation represents significant gross profit opportunity for our retailers.

INFORMATION ON SERVICING THE PRE-TENSIONER SEAT BELT RETRACTOR. *RM

INCLUDED IN THE RESTRAINTS SECTION OF THE ELECTRONIC SERVICE MANUAL (ESM) FOR EACH VEHICLE IS INFORMATION NECESSARY TO SERVICE THE SUPPLEMENTAL RESTRAINT SYSTEM (SRS) SAFELY. IMPROPER MAINTENANCE, INCLUDING INCORRECT REMOVAL AND INSTALLATION OF THE SRS, CAN LEAD TO A SERIOUS INJURY OR DEATH CAUSED BY UNINTENTIONAL ACTIVATION OF THE SRS. NO MODEL OR MODEL YEARS LISTED. *PE UPDATED 2/21/14. *PE

See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

service information in this bulletin along with the Electronic Service Manual (ESM). The updated information in this bulletin is a correction and a supplement to the ESM.

This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.

IF A MALFUNCTION IN THE ASCD SYSTEM IS DETECTED, THE CRUISE INDICATOR MAY STAY ON AND THE SET INDICATOR MAY FLASH. *JS

Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.

trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.