2015 Indian Chieftain TSBs

lever on 2014+ Chieftain motorcycles.

2014+ Chieftain motorcycles.

belt on 2014+ Chieftain motorcycles.

2014+ Indian Chieftain motorcycles.

Motorcycles, resulting in the unexpected loss of forward lighting. This defect may also cause heat damage to the Vehicle Control Module (VCM) and Pin 11 of the center VCM connector. Indian Motorcycle has released this bulletin with instructions to inspect the VCM connector for damage, update the VCM software, and replace the VCM and pin 11 connector if damaged.

or the vehicle harness if the battery ground cable and ground joint is not connected properly. Damage can occur during procedures that require the battery cable to be disconnected or during battery removal and installation.

/ 116 c.i.) and 2020 Challenger models sold in Japan show compliance concerns due to operating range frequency of key fob, Vehicle Control Module (VCM) or Wireless Control Module (WCM), and Tire Pressure Monitor System (TPMS). Mentioned devices operate in restricted in Japan frequency of 433Hhz.

/ 116 c.i.) and 2020 Challenger models sold in Japan show compliance concerns due to operating range frequency of key fob, Vehicle Control Module (VCM) or Wireless Control Module (WCM), and Tire Pressure Monitor System (TPMS). Mentioned devices operate in restricted in Japan frequency of 433Hhz.

motorcycles. When active, the P1530 fault causes the motorcycle to operate in a reduced power (limp) mode.

concerns about correct odometer value.

inaccurate signal, which can lead to an incorrect gear being displayed. Oxidation on the contacts of the gear position switch may cause a change in resistance values resulting in the rider display indicating an incorrect gear. Incorrect gear indication during start-up can increase the risk of a crash.

inaccurate signal, which can lead to an incorrect gear being displayed. Oxidation on the contacts of the gear position switch may cause a change in resistance values resulting in the rider display indicating an incorrect gear. Incorrect gear indication during start-up can increase the risk of a crash.

inaccurate signal, which can lead to an incorrect gear being displayed. Oxidation on the contacts of the gear position switch may cause a change in resistance values resulting in the rider display indicating an incorrect gear. Incorrect gear indication during start-up can increase the risk of a crash.

Number 2881676, may experience intermittent drivability issues.

the Thunder Stroke 116 ci Stage 3 Big Bore accessory kit. Investigation is currently planned to conclude by 5/7/18, and at that time this communication will be re-issued with additional information. In the interim, Big Bore Kits and vehicles equipped with kits should not be sold.

The Indian Motorcycle engineering team has released updated ECM and cluster calibrations to correct these concerns. Gear Position Fault, Coil Driver Fault, and Battery Drain issues will all be resolved with this reflash. Refer to Team Tip I-17-11-01 for more details.

It is critical for expedient and accurate diagnosis of a motorcycle, to identify and disclose all existing modifications to Indian Technical Service. Use of aftermarket components can create operating characteristics and sensor feedback that do not align with factory parameters. These cases can send our technicians down the wrong path and result in longer diagnostic time and a poor customer experience.

i.) models. Updated information has been added to the Service Manual to provide dealers with clear direction on how to properly maintain and service gear position switches. We have also updated the maintenance interval chart to include the inspection and cleaning of the gear position switch at 10,000 mile intervals.

vibration resistance, weight savings, and high output. This Team Tip is being released to provide the Indian dealer network with specific recommendations to help maintain and restore the AGM type batteries used in Indian Motorcycles.

operation, alarm compatibility, battery life expectations and troubleshooting. 2014-2016 Indian Chief, Chieftain and Roadmaster motorcycles utilize a keyless ignition system (Key Fob) for vehicle startup and operation. The Key Fob acts as a two-way transmitter which provides an authentication signal to the Vehicle Control Module (VCM) located on the motorcycle. When the Key Fob is detected, the ignition system is enabled and the motorcycle becomes operational.

to shipping and / or concealed crate damage. In the event that damage occurs during the shipping process, or that damage is concealed under the shipping bag, it is critical to adhere to the claim steps outlined in this communication. Following the guidelines explained below will expedite repairs and allow Indian Motorcycle to seek carrier reimbursement when applicable.

5139174.

device connected to the USB connector. It is important to disconnect all devices from the USB connector prior to performing an ECU, VCM, ABS Controller, Instrument Cluster or Audio System reprogramming (reflash) procedure. A technician should be familiar with Digital Wrench and computer operation in general before attempting any reprogramming (reflash) procedure. Refer to the appropriate Indian Motorcycle Service Manual for additional information.

address customer concerns with Brake-Throttle Override (BTO) functionality. The BTO system will temporarily close the throttle plate and, in some cases, illuminate the Malfunction Indicator Lamp (MIL) if the brakes and throttle are applied at the same time while the vehicle is in motion. While this operation is normal, it is not always compatible with each individual riding style.

Be sure to reference the applicable Service Manual for the most accurate information.

engine production, and introduces a new service crankcase for 2014-2020 models.

The version has been translated into French.

of November 2015