2017 Indian Chieftain Dark Horse TSBs

2014+ Indian Chieftain motorcycles.

Motorcycles, resulting in the unexpected loss of forward lighting. This defect may also cause heat damage to the Vehicle Control Module (VCM) and Pin 11 of the center VCM connector. Indian Motorcycle has released this bulletin with instructions to inspect the VCM connector for damage, update the VCM software, and replace the VCM and pin 11 connector if damaged.

or the vehicle harness if the battery ground cable and ground joint is not connected properly. Damage can occur during procedures that require the battery cable to be disconnected or during battery removal and installation.

/ 116 c.i.) and 2020 Challenger models sold in Japan show compliance concerns due to operating range frequency of key fob, Vehicle Control Module (VCM) or Wireless Control Module (WCM), and Tire Pressure Monitor System (TPMS). Mentioned devices operate in restricted in Japan frequency of 433Hhz.

/ 116 c.i.) and 2020 Challenger models sold in Japan show compliance concerns due to operating range frequency of key fob, Vehicle Control Module (VCM) or Wireless Control Module (WCM), and Tire Pressure Monitor System (TPMS). Mentioned devices operate in restricted in Japan frequency of 433Hhz.

motorcycles. When active, the P1530 fault causes the motorcycle to operate in a reduced power (limp) mode.

concerns about correct odometer value.

Through product design, dedicated safety engineering, and increased consumer awareness, Polaris continues to work toward a safe riding experience and proper operation of our products. The following information can be used to help identify and report Product Safety Concerns.

inaccurate signal, which can lead to an incorrect gear being displayed. Oxidation on the contacts of the gear position switch may cause a change in resistance values resulting in the rider display indicating an incorrect gear. Incorrect gear indication during start-up can increase the risk of a crash.

inaccurate signal, which can lead to an incorrect gear being displayed. Oxidation on the contacts of the gear position switch may cause a change in resistance values resulting in the rider display indicating an incorrect gear. Incorrect gear indication during start-up can increase the risk of a crash.

inaccurate signal, which can lead to an incorrect gear being displayed. Oxidation on the contacts of the gear position switch may cause a change in resistance values resulting in the rider display indicating an incorrect gear. Incorrect gear indication during start-up can increase the risk of a crash.

the Thunder Stroke 116 ci Stage 3 Big Bore accessory kit. Investigation is currently planned to conclude by 5/7/18, and at that time this communication will be re-issued with additional information. In the interim, Big Bore Kits and vehicles equipped with kits should not be sold.

The Indian Motorcycle engineering team has released updated ECM and cluster calibrations to correct these concerns. Gear Position Fault, Coil Driver Fault, and Battery Drain issues will all be resolved with this reflash. Refer to Team Tip I-17-11-01 for more details.

The Indian Motorcycle engineering team has released updated ECM and cluster calibrations to correct these concerns. Gear Position Fault, Coil Driver Fault, and Battery Drain issues will all be resolved with this reflash. Refer to Team Tip I-17-11-01 for more details.

may experience functional issues with the Ride Command navigation system and compass feature. When using navigation on affected bikes, the heading will always show the vehicle traveling North, causing turn-by-turn to continuously reroute. Additionally, the compass image on the Ride Data screen will not be shown.

It is critical for expedient and accurate diagnosis of a motorcycle, to identify and disclose all existing modifications to Indian Technical Service. Use of aftermarket components can create operating characteristics and sensor feedback that do not align with factory parameters. These cases can send our technicians down the wrong path and result in longer diagnostic time and a poor customer experience.

i.) models. Updated information has been added to the Service Manual to provide dealers with clear direction on how to properly maintain and service gear position switches. We have also updated the maintenance interval chart to include the inspection and cleaning of the gear position switch at 10,000 mile intervals.

Dealers should encourage Indian Motorcycle riders using Ride Command to bring their bikes in to receive the software update. At this time, dealers should also verify the map version and update as necessary. The software update takes approximately 5 minutes to complete, while updating the map files may take up to 2 hours depending on PC configuration and internet speed. Ensure the staff is aware of, and has practiced both update processes so they can provide a positive customer experience.

Dealers should encourage Indian Motorcycle riders using Ride Command to bring their bikes in to receive the software update. At this time, dealers should also verify the map version and update as necessary. The software update takes approximately 5 minutes to complete, while updating the map files may take up to 2 hours depending on PC configuration and internet speed. Ensure the staff is aware of, and has practiced both update processes so they can provide a positive customer experience.

vibration resistance, weight savings, and high output. This Team Tip is being released to provide the Indian dealer network with specific recommendations to help maintain and restore the AGM type batteries used in Indian Motorcycles.

The Indian Motorcycle engineering team is working quickly to develop and release updated ECM and cluster calibrations to correct these concerns, but during the interim, the strategies outlined below can reduce customer frustration and unnecessary diagnostic time.

to answer a few questions about basic troubleshooting and system operation. It is important to understand how Ride Command operates and what to expect during normal operation. When delivering an Indian Motorcycle equipped with Ride Command, make sure the customer understands each of the points outlined in this communication. Additional Ride Command information can be found under Training and Resources under News, Forms & Links on your dealer homepage and also at https://my.indianmotorcycle.com/ridecommand/tutorials

Be sure to reference the applicable Service Manual for the most accurate information.

engine production, and introduces a new service crankcase for 2014-2020 models.

The version has been translated into French.

later requires dealers to enter a valid 10-digit Digital Wrench serial number to operate the app. The serial number requirement has been added to improve visibility to app downloads and usage.

times in the ownership experience. To ensure that all Polaris dealers are equipped to deliver a world-class experience that matches the high quality and excitement of the products, PCDX was developed to create a mobile streamlined dealership delivery experience. PCDX combines the setup, registration, and delivery process into one easy to use application.

PCDX training.

The interface walks the dealer and the customer through a standardized online form that includes the PDI (pre-delivery inspection), general warnings, assembly and inspection, safety bulletins, test ride, customer information, customer walkaround and discussion, and customer acceptance. This application has been proven in dealerships to automate document retention, streamline vehicle setup, and provide a consistent, professional customer experience. Vehicles shipped after 11/1/2015 no longer include a paper PDI form with the vehicle setup material; instead dealers should complete the vehicle setup and PDI using the PCDX application, which can be located on the Dealer Website under Service and Warranty PCDX.

the continuous improvements being made.