2019 Indian Chief Vintage TSBs

Motorcycles, resulting in the unexpected loss of forward lighting. This defect may also cause heat damage to the Vehicle Control Module (VCM) and Pin 11 of the center VCM connector. Indian Motorcycle has released this bulletin with instructions to inspect the VCM connector for damage, update the VCM software, and replace the VCM and pin 11 connector if damaged.

or the vehicle harness if the battery ground cable and ground joint is not connected properly. Damage can occur during procedures that require the battery cable to be disconnected or during battery removal and installation.

/ 116 c.i.) and 2020 Challenger models sold in Japan show compliance concerns due to operating range frequency of key fob, Vehicle Control Module (VCM) or Wireless Control Module (WCM), and Tire Pressure Monitor System (TPMS). Mentioned devices operate in restricted in Japan frequency of 433Hhz.

/ 116 c.i.) and 2020 Challenger models sold in Japan show compliance concerns due to operating range frequency of key fob, Vehicle Control Module (VCM) or Wireless Control Module (WCM), and Tire Pressure Monitor System (TPMS). Mentioned devices operate in restricted in Japan frequency of 433Hhz.

concerns about correct odometer value.

motorcycles. In some instances, the throttle twist grip and Electronic Throttle Control (ETC) position signals do not align with the predicted position within the ECM and set a P1530 fault (throttle plausibility). When active, the P1530 fault causes the motorcycle to operate in a reduced power (limp) mode.

Through product design, dedicated safety engineering, and increased consumer awareness, Polaris continues to work toward a safe riding experience and proper operation of our products. The following information can be used to help identify and report Product Safety Concerns.

inaccurate signal, which can lead to an incorrect gear being displayed. Oxidation on the contacts of the gear position switch may cause a change in resistance values resulting in the rider display indicating an incorrect gear. Incorrect gear indication during start-up can increase the risk of a crash.

inaccurate signal, which can lead to an incorrect gear being displayed. Oxidation on the contacts of the gear position switch may cause a change in resistance values resulting in the rider display indicating an incorrect gear. Incorrect gear indication during start-up can increase the risk of a crash.

inaccurate signal, which can lead to an incorrect gear being displayed. Oxidation on the contacts of the gear position switch may cause a change in resistance values resulting in the rider display indicating an incorrect gear. Incorrect gear indication during start-up can increase the risk of a crash.

from 7/18/2016 through 11/27/2018. The chrome trim strips applied to the front and rear fenders may exhibit a wrinkling finish shortly after installation.

It is critical for expedient and accurate diagnosis of a motorcycle, to identify and disclose all existing modifications to Indian Technical Service. Use of aftermarket components can create operating characteristics and sensor feedback that do not align with factory parameters. These cases can send our technicians down the wrong path and result in longer diagnostic time and a poor customer experience.

i.) models. Updated information has been added to the Service Manual to provide dealers with clear direction on how to properly maintain and service gear position switches. We have also updated the maintenance interval chart to include the inspection and cleaning of the gear position switch at 10,000 mile intervals.

The version has been translated into French.

later requires dealers to enter a valid 10-digit Digital Wrench serial number to operate the app. The serial number requirement has been added to improve visibility to app downloads and usage.

times in the ownership experience. To ensure that all Polaris dealers are equipped to deliver a world-class experience that matches the high quality and excitement of the products, PCDX was developed to create a mobile streamlined dealership delivery experience. PCDX combines the setup, registration, and delivery process into one easy to use application.

PCDX training.

Updating to version 4.0 is required to update the base Digital Wrench software version from 3.9 to 4.0 to allow for future MY19 vehicle support.

The interface walks the dealer and the customer through a standardized online form that includes the PDI (pre-delivery inspection), general warnings, assembly and inspection, safety bulletins, test ride, customer information, customer walkaround and discussion, and customer acceptance. This application has been proven in dealerships to automate document retention, streamline vehicle setup, and provide a consistent, professional customer experience. Vehicles shipped after 11/1/2015 no longer include a paper PDI form with the vehicle setup material; instead dealers should complete the vehicle setup and PDI using the PCDX application, which can be located on the Dealer Website under Service and Warranty PCDX.