2022 Ic Bus Resb TSBs
50 Technical Service Bulletins across 13 categories
Categories
Other
15 bulletinsIC Bus Operator's Manuals
This document will guide the user through understanding Prop Shaft Codes and understanding the variations of prop codes.
Read full bulletin
(Metric Prop codes start with the number a 4 and Non metric Prop codes start with a 2.)
Title: Driveline Information Center and Troubleshooting Procedures Applies To: All Vehicles
Title: Fan belt replacement guidelines for frayed edges Applies To: All Models
J1939 Data Link Source Address Information
Diagnosis of chassis wander complaints.
Luggage rack upholstery repair; only busses equipped with luggage rack.
J1939 Data Link Source Address Information
J1939 Data Link Troubleshooting
J1939 Data link source address information
Pico Scope CCOS (Crankcase Separator Test)
PicoScope Test One Channel RCT
PicoScope Test Resistance and Ohmmeter
PicoScope Test for Datalink (CAN) Health Shorts & opens
Certain 2022 and 2023 CE and RE school buses built with feature code 0008TXK or 0008TXM (Bendix Wingman Prewire option)...
Read full bulletin
may have been built without the warning label to notify the driver that the collision mitigation system is not operational, as
Engine
13 bulletinsThis document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature.
Read full bulletin
Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
This document provides guidance for assessing the feasibility of implementing a customer-requested change to an engine or vehicle parameter/feature.
Read full bulletin
Customer requested changes will be approved in accordance with the requirements specified in 40 CFR Part 1037 to ensure continued compliance with greenhouse gas (GHG) regulations.
New CARB Idle Reduction Change Request
Engine replacements for all International engines will need to follow this procedure.
In some geographic areas, ambient temperatures reaching below 15F (-10 C), including high levels of humidity, an...
Read full bulletin
operator may experience engine stalling, low performance, and or poor aftertreatment performance. This is caused by condensation accumulating and freezing within the Charge Air Cooler (CAC); affecting air flow into the engine. This article lists all the currently available winter front covers that can be installed on the front grille and bumper to reduce cold air flow to the engine compartment.
Title: How to Request a Horsepower Quote Applies To: All International and Cummins Electronic engines
Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or...
Read full bulletin
PSI engine.
How to request a horsepower quote; all International and Cummins engines
Per agreement with EPA and CARB, Cummins, Inc.
Read full bulletin
provided an emergency calibration for Cummins ISB, B6.7, ISL9, L9, and X15 engines when a DEF Quality Sensor (DQS) was not available. This action addressed the Diesel Exhaust Fluid (DEF) Quality Sensor failures in the field and the unavailability of parts due to the worldwide chip shortage. This recall is step two of this program designed to revert all affected vehicles back to the certified calibration and to provide them with the latest improved DQS and Coolant Control Valve (CCV) designs. Additionally, the emergency calibration and the restoration to the certified calibration with the latest improved DQS and Coolant Control Valve (CCV) designs have no effect on vehicle Emissions.
Cummins Programming guide and fault codes285 & 265; only vehicles built with Cummins B6.7, X15, or L9 engines
Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI...
Read full bulletin
engines or Cummins ISB engine with Allison transmissions
QLS Emergency ECM Calibration; only models equipped with Cummins B6.7, X15, L9, or International A26 engines
QLS Emergency Calibration.
Read full bulletin
applies to 2016 and newer Cummins B6.6, X15, and L9 engines and all A26 engines
Brakes
4 bulletinsThis document will guide the user through a step-by-step procedure for detecting water leaks in vehicle cabs and...
Read full bulletin
windshields using an ultrasonic sound detector.
Certain IC RE school buses may have the ABS indicator light circuit incorrectly pinned at the relay and may have an...
Read full bulletin
outdated BCM calibration that could result in the ABS indicator light to stay on at all times
Certain IC RE school and commercial buses may have outdated BCM calibration that could result in the ABS indicator light...
Read full bulletin
illuminating at all times
The rear axle brake chambers may be installed in the incorrect mounting slot which could lead to long term durability...
Read full bulletin
issues.
HVAC & Climate
3 bulletinsTitle: A/C Refrigerant and Oil Capacities Applies To: All current models
Title: Factory Installed Air Conditioning, EC4.0 System BE, CE, FE, RE Bus Models
Air Compressor Inlet Hose Chaffing / Leaking
Body & Paint
3 bulletinsThis article addresses chassis lean conditions on all chassis.
Read full bulletin
This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
These certain buses may have roof water leaks resulting from incorrect assembly described in Roof Joint Recalls 23501...
Read full bulletin
and 23502.
Bus roof leaks
Electrical
3 bulletinsCummins B6.7 Grid Heater Relay
General Wheel Speed Sensor Troubleshooting
PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
Pre-Delivery & Maintenance
2 bulletinsTitle: Service Portal iKNow Feedback Case Types Applies To: All
Bus seat back foam inspection guidelines
Software & Calibration
2 bulletinsQLS Emergency Calibration Revert Process
QLS Emergency Calibration Revert Process
Infotainment
1 bulletinThis tool is designed to compare Diamond Logic feature data across multiple vehicle configuration files.
Read full bulletin
It allows users to quickly load files either manually or directly from the Diamond Logic Builder Vehicles folder using VIN-based selection. As files are added or removed, the comparison runs automatically with no manual action required. The program presents results in an interactive table that shows feature codes, descriptions, access levels, and whether each feature is present in each selected file. Built-in search, filtering, and sorting make it easy to locate specific features or focus only on differences between files. Column visibility can be customized to show or hide descriptions and access information as needed. Users can remove files individually or clear all files at once, with results updating instantly. The tool also includes reporting and export options that reflect exactly what is visible on screen, allowing results to be printed, copied, saved as text, or exported to CSV for use in Excel or other spreadsheet tools. Overall, the program streamlines the process of comparing vehicle feature configurations, helping users quickly identify differences, validate setups, and document results without manual comparison or external tools.
Transmission
1 bulletinTitle: Steering Gear Seal Repair Guidelines Applies To: Steering gears
Tires & Wheels
1 bulletinSuggested alignment target values when performing a vehicle axle alignment.
Fuel System
1 bulletinBus Diesel fuel Cap Leaks; only models built 11/30/2020 through 05/18/2023
Steering
1 bulletinThe steering wheel retaining nut may not have been torqued properly during assembly and may allow the steering wheel to...
Read full bulletin
loosen, and possibly separate from the steering column shaft.