2008 Hyundai Veracruz TSBs

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

*RM

SOME 2.7L, 3.3L OR 3.8L ENGINES IN MODELS IDENTIFIED IN THE APPLICABILITY LIST MAY EXPERIENCE ONE OR MORE OF THE CONDITIONS LISTED. *PE

SOME VEHICLES MAY EXPERIENCE EITHER SLIGHT ENGINE RPM FLUCTUATION AT COLD WARM UP OR MALFUNCTION INDICATOR LAMP ILLUMINATED WITH THE ETC (ELECTRONIC THROTTLE CONTROL) SYSTEM. *PE

State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

(AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.

(AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.

TOOL TO COMMUNICATE WITH AN ECU OR TCU. *PE

VEHICLES MAY EXPERIENCE A COMMUNICATION FAILURE CODE WHEN USING GENERIC SCAN TOOL. *PE

*NJ

*NJ

CONTROL) SYSTEM RELATED DTC P2135 ( FORCED LIMITED POWER) OR DTC P0638 (POWER MANAGEMENT). *PE

CONTROL) SYSTEM RELATED DTC P2135 OR DTC P0638. *PE

LABEL REQUIREMENTS FOR VEHICLE LOADING TO COMPLY WITH FMVSS 110. *PE

*NJ

*NJ

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

diagnosing and conducting alignment-related repairs for all models and model years.

EFFECTIVE 6/2/08, FMVSS 110 (FMVSS 110) SETS A THRESHOLD FOR CORRECTING LOAD CAPACITY INFORMATION INDICATED ON TIRE PLACARDS WHEN VEHICLE WEIGHT HAS BEEN INCREASED BEFORE RETAIL SALE. ALL MODELS INCLUDED AFTER 6/2/08. *PE

recommended safe chemical products.

chemical products.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.

*PE

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.

IF A NAVIGATION SYSTEM EXPERIENCES LOCK UP DURING OPERATION, THIS BULLETIN DESCRIBES THE REPAIR PROCEDURE NECESSARY TO REPROGRAM THE NAVIGATION SOFTWARE. *PE

IF A NAVIGATION SYSTEM EXPERIENCES LOCK UP DURING OPERATION, THIS BULLETIN DESCRIBES THE REPAIR PROCEDURE NECESSARY TO REPROGRAM THE NAVIGATION SOFTWARE. *PE

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

original retail delivery or date of first use, whichever occurs first. This warranty coverage applies to both the original and subsequent owners. Refer to the warranty and service parts information outlined in this bulletin whenever clock spring replacement is required.

OEM (new) and remanufactured automatic transmissions:

THIS BULLETIN PROVIDES THE PROCEDURES NECESSARY TO RESET (ERASE) AND RELEARN THE PCM/TCM ADAPTIVE VALUES. AFTER THE FOLLOWING REPAIRS HAVE BEEN COMPLETED, THE PCM/TCM ADAPTIVE VALUES MUST BE RESET IN ORDER TO PROVIDE OPTIMUM SHIFT QUALITY. IF THE PROCEDURE IS NOT PERFORMED, THE TRANSMISSION MAY EXPERIENCE A SHIFT FLARE OR HARSH SHIFT. H REPLACE AUTOMATIC TRANSAXLE OR PCM/TCM H REPROGRAM OR EXCHANGE A PCM/TCM FROM ANOTHER VEHICLE"

*RM

THE SERVICE PROCEDURE TO REPLACE BOTH THE TILT LIMIT SWITCH AND THE TELESCOPE LIMIT SWITCH WITH REPLACEMENT SERVICE PARTS. *PE