2022 Hyundai Tucson TSBs

have DTC U028700 (Lost Communication With Trans Fluid Pump Module) set by the transmission Electric Oil Pump (EOP). This DTC can cause the Idle Stop & Go (ISG) system to become inoperative. Follow the procedure in this bulletin to replace the Electric Oil Pump on affected vehicles.

Electronic Control Unit (ECU), resulting in an illuminated Check Engine warning lamp. This TSB provides instructions to replace the Integrated Thermal Management (ITM) module and update both the Engine Control Module (ECM) and Transmission Control Module (TCM), if applicable. Follow the flowchart in this bulletin to update the appropriate modules.

fuel injectors leaking internally. This may be caused by internal filter breakage in the injector. Follow the procedure in this TSB to replace all 4 injectors on affected vehicles, using the kit in the Parts Information section.

installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).

ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.

anti-theft decals on the front windows.

available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, weve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (Subject Vehicle) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed if you request it at no cost to you through an authorized Hyundai dealership.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

This may be caused by internal filter breakage in the injector. Follow the procedure in this TSB to replace all 4 injectors on affected vehicles, using the kit in the Parts Information section.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

vehicles and the Engine Control Module (ECM) for the 2022-24MY Tucson vehicles to improve operation of the Idle Stop and Go (ISG) system. Under certain circumstances the vehicle may not restart after ISG system has engaged and require a manual restart due to the lack of intake manifold pressure recovery.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

or symptoms listed below, refer to the Service Procedure to diagnose the condition. DIAGNOSTIC TROUBLE CODES: P070500 - Transmission range sensor circuit malfunction P070512 - Transmission range sensor circuit malfunction P070514 - Transmission range sensor circuit malfunction P07051C - Transmission range sensor circuit malfunction P070600 - Transmission range sensor circuit range/performance P070661 - Transmission range sensor circuit range/performance P070696 - Transmission range sensor circuit range/performance SYMPTOMS: Malfunction Indicator Light (MIL) illuminated 5th gear fail-safe Intermittently wont shift into D or R Intermittently wont shift out of Park Intermittent ly no engine cr ank/n o start in P or N with or without MIL or DTC.

service procedure and replace the related solenoid and harness.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32).

certain 22MY Santa Cruz, and certain 21-23MY Tucson equipped with 2.5L GDI engines with one or more misfire DTC(s) due to internally leaking GDI injector(s)

in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.

service procedure and replace the related solenoid and harness.

certain 22MY Santa Cruz, and certain MY21-23 Tucson equipped with 2.5L GDI engines with one or more misfire DTC(s) due to internally leaking GDI injector(s).

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

22MY Santa Cruz, and Tucson equipped with 2.5L GDI engines with one or more misfire DTC(s) due to internally leaking GDI injector(s).

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

the repair procedure and replace the related input/output speed sensor and harness.

nor radial force variation (RFV). This bulletin describes the procedure to update the anti-shimmy logic in the Motor Driven Power Steering (MDPS) ECU.

the repair procedure and replace the related solenoid and valve body harness.

engine may exhibit a MIL with DTC(s): P2074: Mass Airflow Sensor Plausibility P2074F0: Manifold Absolute Pressure/Mass Air Flow - Throttle Position Correlation at Lower Load P2074F1: Manifold Absolute Pressure/Mass Air Flow - Throttle Position Correlation at Medium or High Load Secondary DTC(s) below may also be stored: C136081: ESP Irreversible Error C161308: CAN Signal Error EMS C161386: CAN Signal Error EMS C169381: Blind-Spot Collision Warning CAN signal failure - ESC C174181: ESC Not Available VSM (Check ESC) C183586: CAN Message Failure ESC/IEB Vehicles diagnosed with DTC(s) may also experience reduced engine performance and limited power reduction mode. The ECM software revises the logic to accurately detect the amount of air the engine is receiving.

Procedure to diagnose the condition. DIAGNOSTIC TROUBLE CODES: P070500 - Transmission range sensor circuit malfunction P070512 - Transmission range sensor circuit malfunction P070514 - Transmission range sensor circuit malfunction P07051C - Transmission range sensor circuit malfunction P070600 - Transmission range sensor circuit range/performance P070661 - Transmission range sensor circuit range/performance P070696 - Transmission range sensor circuit range/performance SYMPTOMS: Malfunction Indicator Light (MIL) illuminated 5th gear fail-safe No gear indication in cluster Intermittently wont shift into D or R Intermittently wont shift out of Park Intermittent ly no engine cr ank/no start in P or N with or without MIL or DTC.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

system.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB. The NAU website is https://update.hyundai.com/US/EN/navigationUpdate. For certain models equipped with a relevant Bluelink package, the software may be downloaded and applied via OTA update.

system.

system.

when entering radio mode and/or displays a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

system.

when entering radio mode and/or displays a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

unavailability.

of no audio or intermittent sound from the vehicle's speakers.

vehicles equipped with an external amplifier.

unavailability.

caused by other wireless noise from unknown sources which could make wireless communication unstable between D-Audio and mobile phone.

improve shift quality, judder and hesitation when accelerating.

(transmission clutch slip in gear above limit) listed on Page 2.

improve shift quality, judder with ISG enabled and hesitation when accelerating.

If replacement of the SBW button is required due to one or more button plating peeling, replace the button(s) with a new one. Do not replace the complete SBW lever.

If you are servicing a vehicle with any symptoms listed below or DTCs (listed on Page 2) , follow the Service Procedure on Page 3. SYMPTOMS: Shifter System Malfunction displayed in the cluster Wont shift into or out of gear or wont shift out of Park Incorrect gear display in cluster and/or wont start

or symptoms listed below, refer to the Service Procedure to diagnose the condition.

accelerating.

This type of leak is caused by a porous casting on the rear cover of the transmission.

accelerating.

If you are servicing a vehicle with any symptoms or DTC listed below, follow the Service Procedure, Page 2.

accelerating.

illumination for a diagnostic trouble code P2181 that is related to the Integrated Thermal Management Module (ITM). Follow the service procedure outlined in this bulletin to replace the ITM.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This battery diagnosis function displays the various battery-related faults such as: Internal short circuit Battery deterioration Malfunction of electronic parts Insufficient battery charge Normal battery Charging defect Battery diagnosis uses the battery sensor history saved for the last 30 days and ICU diagnostic communication to track battery state of charge (SOC) and current parasitic draw history.

remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 2 P0456 - Evaporative System

Hyundai is extending the warranty coverage for the horn replacement to 10 years/120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. If a horn needs to be replaced, follow the instructions within Technical Service Bulletin (TSB) 26-BE-004H to replace both low pitch and high pitch horns. Please note that any vehicles under 10 years/120,000 miles are covered by this TSB, even if vehicle is within original warranty of 5 years/60,000 miles.

Hyundai is extending the warranty coverage for the horn replacement to 10 years/120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. This bulletin provides instructions on how to replace both inoperative horns. Please note that any vehicles under 10 years/120,000 miles are covered by this TSB, even if vehicle is within original warranty of 5 years/60,000 miles.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

C272246 fault code for the front camera. In the following cases, the front camera auto-calibration range may be exceeded while driving: If the front camera is not properly installed and is completely or partially detached. In case of excessive changes affecting the vehicle's balance (e.g., loading excessively heavy cargo in a specific location of the vehicle, or significant under-inflation of the tires). Specific road conditions affecting the vehicle's balance (e.g., excessive road crown) This TSB provides instructions on how to service the vehicle when the front camera related warning light(s) are triggered due to system out of calibration (DTC_C272246).

license plate lamps, caused by out of specification lamp housings. This bulletin provides the procedures to repair the condition by replacing the affected license plate lamps.

This bulletin describes the procedure to inspect the rear center combination lamp and repair or replace it if necessary.

After a new vehicle launch, Hyundai uses the LQMP to monitor all customer and dealer activities at a minimum of 100 days. The Tucson LQMP helps improve model vehicle quality, and allows Hyundai to proactively respond to the Voice of the Customer (VOC).

closing condition due to an inoperative fuel filler door release actuator. This bulletin provides instructions to replace the fuel filler door release actuator.

2022MY Tucson (NX4/NX4a) vehicles.

This bulletin describes the procedure to inspect the brakes, resurface or replace and perform a brake burnishing procedure.

This bulletin outlines the procedures to inspect and replace the assembly if necessary.

2022 2023MY Tucson (NX4A) and Santa Cruz (NXT) vehicles. If a vehicle exhibits this paint peeling condition, replace the front door trim panel assembly.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

NX4A, NX4 HEV, NX4 PHEV) vehicles. Update will reduce sensitivity of LKA warning and misrecognition of missing lanes when entering the interstate.