2025 Hyundai Sonata TSBs

This bulletin outlines the combustion chamber cleaning procedure for vehicles diagnosed with this condition. All internal combustion engines consume some engine oil during normal operation, depending on driving conditions and mileage, and this procedure should only be performed when deemed necessary based on inspection and diagnosis of the vehicle as outlined in TSB 26-EM-015H, Engine Oil Consumption Inspection & Repair Guidelines, or the latest revision.

This bulletin provides the inspection and repair procedures for vehicles exhibiting this condition. All internal combustion engines consume engine oil as part of normal engine operation. Oil consumption rates may vary based on mileage, operating conditions, driving habits, and maintenance history. Hyundai recommends following the prescribed maintenance schedule and periodically checking the engine oil level using the dipstick to maintain proper engine oil level.

oil level plug that could potentially lead to a total failure of the automatic transmission. This bulletin provides instructions to inspect the oil level plug and transmission oil level and, if necessary, replace the automatic transmission.

oil level plug that could potentially lead to a total failure of the automatic transmission. Technical Service Bulletin (TSB) 26-01-060H instructions to inspect the oil level plug and transmission oil level and, if necessary, replace the automatic transmission.

lamp and store Diagnostic Trouble Code (DTC) P2B59F0, which relates to the Integrated Thermal Management Module (ITM) circuit due to a logic error. This bulletin provides instructions to update the Engine Control Module (ECM) logic to correct this condition.

The matter is being investigated. We will provide an update once the issue is resolved and the suspension is lifted.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

Some vehicles are not being able to complete the update after multiple attempts. Technicians may experience consistent cluster speedometer software upgrade failures when attempting to update to the latest version. A revised version of the software is currently in development to address the update failures and recover any failed modules. We will provide an update once the issue is resolved and the suspension is lifted.

may have speedometers that display the incorrect speed and/or an inoperative turbo boost gauge. This bulletin provides instructions to perform a software update to resolve this concern.

Sunday, February 9th , resulting in the potential loss of connectivity or interruptions when attempting to use Bluelink functions. Voice Recognition, Sports Media, and Weather will not be available. Dealer stock and retailed vehicles are both affected. If a customer calls in and their vehicle is experiencing issues related to Bluelink, please have them come into the dealership to assist with resetting the Bluelink Data Communication Unit (DCU) and utilize TSB 25-BE-003H posted on Hyundai Tech Info.

discharge condition due to the air conditioning controller not fully powering down after the vehicle is turned off and parked. Technical Service Bulletins (TSB) 26-01-051H & 26-01-052H provide the procedure to update the ATCU (Air Temperature Control Unit) software; the revised logic improves controller shutdown to prevent battery drain and corrects a condition where the HVAC control display may appear blank when climate remote start is activated via Bluelink. Over-the-Air (OTA): This update can also be conducted via OTA. Customers can complete on their own if they have an active subscription to Hyundai Bluelink. A visit to the dealership is not required. Deployment of the OTA to Bluelink customers is planned to start the week of 07/13/26.

controller not fully powering down after the vehicle is turned off and parked. This bulletin provides the procedure to update the ATCU (Air Temperature Control Unit) software; the revised logic improves controller shutdown to prevent battery drain and corrects a condition where the HVAC control display may appear blank when climate remote start is activated via Bluelink.

controller not shutting down completely while the vehicle is parked and turned off. TSBs 25-01-075H (for Sonata vehicles) & 25-01-076H (Sonata Hybrid vehicles) provides instructions to perform a software update for the ATCU (Air Temperature Control Unit).

completely while the vehicle is parked and turned off. This bulletin provides instructions to perform a software update for the ATCU (Air Temperature Control Unit).

Instrument Cluster Module require software verification PRIOR to odometer mileage writing. If the Cluster Module does not have the latest software, the incorrect mileage may be written to the new module. This bulletin provides information to confirm the Instrument Cluster Module is equipped with the latest software version prior to using the GDS tablet to write the odometer mileage.

the outside temperature input from the ADAS sensor. Follow the procedures in this bulletin to input the external temperature from the cluster and correct the rear corner radar temperature software using GDS.

This may be due to an occasional disconnection on Verizons communication network. Follow the procedures in this bulletin to verify Bluelink Data Communication Unit (DCU) network connection and if needed, reset the DCU in Dealer Mode to resolve the connection.

This may be due to an occasional disconnection on Verizons communication network. Follow the procedures in this bulletin to verify Bluelink Data Communication Unit (DCU) network connection and if needed, reset the DCU in Dealer Mode to resolve the connection.

This may be due to an occasional disconnection on Verizons communication network. Follow the procedures in this bulletin to verify Bluelink Data Communication Unit (DCU) network connection and if needed, reset the DCU in Dealer Mode to resolve the connection.

This may be due to an occasional disconnection on Verizons communication network. Follow the procedures in this bulletin to reset the Connected Car Data Communication Unit (DCU) in Dealer Mode to resolve the connection.

This bulletin provides instructions to reset the network in Dealer Mode to prevent the Data Concentrator Unit (DCU) modem from experiencing a "Blue Link Not Open" error.

Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2026 1st Navigation Map and Software Update Key Improvements and Additional Improvements tables in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB. The NAU website is https://update.hyundai.com/US/EN/navigationUpdate. For certain models equipped with a relevant Bluelink package, the software may be downloaded and applied via OTA update.

drivers-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

counterfeit driverside airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or noncertified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

equipped with an 8-speed wet dual clutch transmission (8WDCT). The software update revises the touch point learning variation, improving drivability and judder symptoms. Some 8WDCTs (indicated by a new part number) received an updated clutch spring. The correct TCU software update must be matched with the correct corresponding 8WDCT hardware, otherwise, drivability concerns may occur. This service procedure should be performed prior to any 8WDCT replacements done for drivability/judder concerns.

C272246 fault code for the front camera. In the following cases, the front camera auto-calibration range may be exceeded while driving: If the front camera is not properly installed and is completely or partially detached. In case of excessive changes affecting the vehicle's balance (e.g., loading excessively heavy cargo in a specific location of the vehicle, or significant under-inflation of the tires). Specific road conditions affecting the vehicle's balance (e.g., excessive road crown) This TSB provides instructions on how to service the vehicle when the front camera related warning light(s) are triggered due to system out of calibration (DTC_C272246).

Technical Service Bulletins (TSBs) 25-01-048H & TSB 25-01-049H are available today as of 9:00AM PST and the affected VIN population has been reactivated.