2015 Hyundai Sonata TSBs

exhibit elevated engine-out emissions. Technical Service Bulletin (TSB) 26-01-013H-1 provides instructions for updating the Engine Control Module (ECM) to address this condition.

exhibit elevated engine-out emissions.

exhibit elevated engine-out emissions. This bulletin provides instructions for updating the Engine Control Module (ECM) to address this condition.

installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).

ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.

anti-theft decals on the front windows.

available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, weve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (Subject Vehicle) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed if you request it at no cost to you through an authorized Hyundai dealership.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32).

and/or have DTC P1233 stored in the ECM due to an internally leaking fuel pump filter housing. For vehicles exhibiting one or more of these conditions, Hyundai is extending warranty coverage for fuel pump filter assembly repair or replacement to 15 years / 150,000 miles from the date of original retail delivery or date of first use (whichever occurs first). This service action and warranty extension is valid for original and subsequent owners.

and/or have DTC P1233 stored in the ECM due to an internally leaking fuel pump filter housing. Hyundai is extending warranty coverage for fuel pump filter assembly repair or replacement to 15 years / 150,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the service procedure to inspect the low-pressure fuel pump operation and replace the fuel filter if necessary.

in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.

reduced power steering assist and/or motor driven power steering (MDPS) warning lamp has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first. Refer to the TSB 23-ST-003H (or latest version) for warranty, service parts information, and diagnostic information outlined in the bulletin.

power steering assist and/or motor driven power steering (MDPS) warning lamp has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first. Refer to the warranty, service parts information, and diagnostic information outlined in this bulletin.

in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.

software updated to revise the fuel injection control logic to compensate for oxygen sensor aging and control tailpipe emissions within applicable standards.

in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. Please note that all Hyundai vehicles meet or exceed Federal Motor Vehicle Safety Standards. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

rod bearing wear has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first. Warranty coverage is valid for original and subsequent owners.

rod bearing wear has been extended to a Limited Lifetime Warranty and is valid for original and subsequent owners.

DTC P1326 and/or engine may exhibit Abnormal Noise or No Crank/No Start condition. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.

P1326 and/or engine may exhibit abnormal noise or no crank/no start condition related to connecting rod bearing wear or damage. This Dealer Best Practice outlines the service procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results, as well as related warranty coverage for the conditions outlined above.

power steering assist and/or motor driven power steering (MDPS) warning lamp has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first. Refer to the warranty, service parts information, and diagnostic information outlined in this bulletin.

Actuator (EWGA) equipped vehicles listed below. Refer to the applicable Engine Control / Fuel System sections in the Shop Manual, and then follow the procedures outlined in this bulletin whenever a vehicle with the following symptom(s) are being diagnosed: Check Engine Light illumination with EWGA related DTC. Intermittently high/low turbocharger boost pressures. Abnormal noise from the turbocharger.

rod bearing wear has been extended to a Limited Lifetime Warranty and is valid for original and subsequent owners.

reduced power steering assist and/or motor driven power steering (MDPS) warning lamp has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first.

malfunction from connecting rod bearing wear has been extended to a Limited Lifetime Warranty and is valid for original and subsequent owners.

the Check Engine warning lamp illuminated with DTC P1326.

DTC P1326 and/or engine may exhibit Abnormal Noise or No Crank/No Start condition. Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.

Actuator (EWGA) equipped vehicles listed below. Refer to the applicable Engine Control / Fuel System sections in the Shop Manual, and then follow the procedures outlined in this bulletin whenever a vehicle with the following symptom(s) are being diagnosed: Check Engine Light illumination with EWGA related DTC. Intermittently high/low turbocharger boost pressures. Abnormal noise from the turbocharger. Reduced engine power.

Controllers (VCM) equipped in the applicable vehicles listed below. This bulletin also provides information on the use of the Service Kit for 2.4L equipped engines, which enables replacing the VCM Lever Arm without replacing the complete Intake Manifold Assembly. Refer to the applicable Engine Control / Fuel System sections in the Shop Manual, and then follow the procedures outlined in this bulletin whenever a vehicle with the following symptom(s) are being diagnosed: Check Engine Light illumination with VCM related DTC. Unstable engine RPM and reduced engine power. Abnormal noise from the intake manifold whenever engine RPM is raised from idle speed.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

This bulletin provides information on the separate components and the replacement procedure of these components.

damage as described in Campaign T3G (Seized and/or BCT No Pass Result Only) has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. Please refer to TSB # 20-01-024H-2 (or latest revision) for applicable part numbers and labor ops.

Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results. Consult the Hyundai Warranty Policy & Procedures and the below chart to determine New or Reman engine usage.

Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.

Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results. Consult the Hyundai Warranty Policy & Procedures and the below chart to determine New or Reman engine usage.

Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.

retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

as separate components.

as separate components.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

filed against Hyundai Motor America (HMA). Beginning in July 2020, customers affected by the proposed settlement will begin becoming informed of the settlement by mailed notice and email, and they may direct questions to dealers. Please go to HyundaiThetaEngineSettlement.com for full details. In addition, customer questions can also be directed to 1-866-944-7620 (Monday to Friday 7am-5pm PST).

Control Module) to improve the shift quality of the DCT (Dual Clutch Transmission) for these vehicles.

Module) on certain 2015-2017 Hyundai Sonatas equipped with 1.6L turbo engine 7-speed DCT Transmission.

Follow the procedures on TSB #20-01-004H-1 (supersedes TSB #20-01-004H) to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.

Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.

Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results. Consult the Hyundai Warranty Policy & Procedures and the below chart to determine New or Reman engine usage.

Check Engine light on DTC P0880/P088000 - TCM Power signal error open/short Transmission stuck in 4th gear fail-safe Harsh shift into Reverse and Drive

The lawsuit concerns model year 2015 to 2017 U.S. specification Hyundai Sonata vehicles equipped with the Smart Trunk feature purchased or leased in the fifty United States or the District of Columbia (Class Vehicles). The lawsuit alleges that torsion bars on the Smart Trunk in the Class Vehicles are defective because they do not open a sufficient amount. . Defendant has denied these allegations.

the repair procedure and replace the related solenoid and oil pressure harness.

the repair procedure and replace the related solenoid and oil pressure harness.

Follow the procedures on TSB #20-01-004H (supersedes TSB #19-01-006H-4) rotate the crankshaft, perform the bearing inspection (if crankshaft does rotate) and/or replace the engine based on the crankshaft/bearing inspection results.

the repair procedure and replace the related solenoid and oil pressure harness.

Follow the procedure to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results.

bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure. Watch this video to learn more. The KSDS software continuously monitors engine vibrations for unusual patterns that develop as an engine connecting rod bearing wears abnormally that could later cause engine seizure. If vibrations caused by bearing wear start to occur, the malfunction indicator lamp will blink continuously, an audible chime will sound and the vehicle will be placed in a temporary engine protection mode with reduced power and acceleration. At that time, Diagnostic Trouble Code (DTC) P1326 will be recorded in the ECM. In addition, Hyundai will extend the warranty to 10 years and 120,000 miles (up from 100,000 miles) for original and subsequent owners of the covered vehicles for engine repairs needed because of excessive connecting rod bearing damage.

as separate components.

This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.

The lawsuit concerns model year 2015 to 2017 U.S. specification Hyundai Sonata vehicles equipped with the Smart Trunk feature purchased or leased in the fifty United States or the District of Columbia (?Class Vehicles?). The lawsuit alleges that torsion bars on the Smart Trunk in the Class Vehicles are defective because they do not open a sufficient amount. . Defendant has denied these allegations.

? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.

retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine based on the inspection results.

bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure.

the Check Engine warning lamp illuminated with DTC P132600.

retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine based on the inspection results.

bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure.

the Check Engine warning lamp illuminated with DTC P132600.

follow the repair procedure and replace the related solenoid and oil pressure harness

Follow the procedure to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.

as separate components.

eliminate the interference caused by the wiring harness. As a result, we need the vehicles currently waiting for an engine replacement to be re-tested with the new software update using the GDS-mobile.

Check Engine warning lamp illuminated with DTC P1326.

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

Service Campaign T3Q provides a procedure to update the display audio software for blank home screen.

injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional multi-point fuel injection (MPI) engine, relatively low pressure gasoline is injected into the intake port of each cylinder. Due to high fuel pressures in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specification for the GDI fuel system components.

Follow the procedure on TSB #19-01-006H (supersedes TSB# 18-01-032-2) to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.

retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

Follow the procedure to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.

The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure. Watch this video to learn more. The KSDS software continuously monitors engine vibrations for unusual patterns that develop as an engine connecting rod bearing wears abnormally that could later cause engine seizure. If vibrations caused by bearing wear start to occur, the malfunction indicator lamp will blink continuously, an audible chime will sound and the vehicle will be placed in a temporary engine protection mode with reduced power and acceleration. At that time, Diagnostic Trouble Code (DTC) P132600 will be recorded in the ECM. In addition, Hyundai will extend the warranty to 10 years and 120,000 miles (up from 100,000 miles) for original and subsequent owners of the covered vehicles for engine repairs needed because of excessive connecting rod bearing damage.

bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

the onset of excessive connecting rod bearing wear in the engine. The KSDS is designed to alert a vehicle driver at an early stage of bearing wear before the occurrence of engine damage. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, an audible chime will sound, and the vehicle will be placed in Limp Home Mode. At that time, Diagnostic Trouble Code (DTC) P132600, specific to the KSDS, will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed with RPMs limited to approximately 1800-2000 RPM. The update will be done free of charge to customers and will only involve the addition of the KSDS software update.

warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.

retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. Note: Service Campaign 953 must be performed prior to applying this warranty extension.

bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Limp Home Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

This campaign is being implemented to ensure the satisfaction of Hyundai customers. The software update installs a newly developed Knock Sensor Detection System (KSDS) that detects vibrations indicating the onset of excessive connecting rod bearing wear in the engine. The KSDS is designed to alert a vehicle driver at an early stage of bearing wear before the occurrence of engine damage. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, an audible chime will sound, and the vehicle will be placed in Limp Home Mode. At that time, Diagnostic Trouble Code (DTC) P132600, specific to the KSDS, will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed with RPMs limited to approximately 1800-2000 RPM.

bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Limp Home Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

repairs needed due to excessive connecting rod bearing damage upon completion of Service Campaign 953. The warranty extension is for 10 years from the date of original delivery or the date of first use, or 120,000 miles, whichever occurs first.

bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound, and the vehicle will be placed in Limp Home Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

The software update installs a newly developed Knock Sensor Detection System (KSDS) that detects vibrations indicating the onset of excessive connecting rod bearing wear in the engine. The KSDS is designed to alert a vehicle driver at an early stage of bearing wear before the occurrence of engine damage. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, an audible chime will sound, and the vehicle will be placed in Limp Home Mode. At that time, Diagnostic Trouble Code (DTC) P132600, specific to the KSDS, will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed with RPMs limited to approximately 1800-2000 RPM.

Follow the procedure to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.

vehicles to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound, and the vehicle will be placed in Limp Home Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

This may cause an air rushing noise and may cause potential damage to the turbo charger.

vehicles equipped with 2.0L turbo engine. Service Campaign T2K provides a service procedure to replace the air intake hose.

the VCM actuator on certain 2015-16MY Sonata 2.4L vehicles. Service Campaign T1H provides a procedure to update the ECM software and inspect the VCM actuator.

Runner Performance - Bank 1) and for P0605 (Engine Control Module - ROM Error) on certain 2015 and 2016 model year Sonata (LF) vehicles equipped with a 2.4L GDI engine. The vehicle may exhibit one or more of the following conditions: ? DTC P200A (Intake Manifold Runner Performance - Bank 1) ? Check Engine Light ON ? Automatic transmission upshift hesitation ? Clicking noise from the intake manifold VCM (Variable Charge Motion) actuator when the engine RPM is increased ? (2015 MY Only) DTC P0605 (Engine Control Module ? ROM Error) ? Check Engine Light ON ? Electronic Stability Control (ESC) Warning Light ON ? Limited engine power (?Limp Home?) mode

? Diagnostic trouble codes: ? P0705 - Range switch sensor circuit ? P0706 - Range switch range/performance ? P0707 - Range switch - open circuit ? P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ? Malfunction Indicator Light (MIL) illuminated ? 4th gear fail-safe ? No gear indication in cluster ? Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.

THE TOP ALTERNATOR MOUNTING BOLT (A IN THE DIAGRAM) MAY BREAK OVER TIME IF IT IS TIGHTENED OVER SPECIFICATION AND COULD RESULT IN ILLUMINATION OF THE BATTERY WARNING LIGHT AND/OR THE ENGINE OVERHEATING IN SOME CASES. THIS BULLETIN DESCRIBES THE PROCEDURE TO REPLACE THE TOP ALTERNATOR MOUNTING BOLT.

SERVICE CAMPAIGN TTT PROVIDES A PROCEDURE TO REPLACE THE TOP ALTERNATOR MOUNTING BOLT.

ONTO THE ENGINE UNDERCOVER DIRECTLY BENEATH THE HOSE.

2015/2016 MY SONATAS VEHICLES (30 UNITS), AND 2016 MY SONATA HYBRID VEHICLE (ONE UNIT), AND 2017 MY ELANTRA (TWO UNITS) VEHICLES FOR REPLACEMENT OF THE DRIVERS FRONTAL AIRBAG MODULE."

RUNNER PERFORMANCE - BANK 1) AND FOR P0605 (ENGINE CONTROL MODULE - ROM ERROR) ON CERTAIN 2015 AND 2016 MODEL YEAR SONATA (LF) VEHICLES EQUIPPED WITH A 2.4L GDI ENGINE. THE VEHICLE MAY EXHIBIT ONE OR MORE OF THE FOLLOWING CONDITIONS: CHECK ENGINE LIGHT ON SLIGHT HESITATION OR REDUCED POWER DURING ACCELERATION AUTOMATIC TRANSMISSION UPSHIFT HESITATION DURING ACCELERATION CLICKING NOISE FROM THE INTAKE MANIFOLD VCM (VARIABLE CHARGE MOTION) ACTUATOR WHEN THE ENGINE RPM IS INCREASED ELECTRONIC STABILITY CONTROL (ESC) WARNING LIGHT ON LIMITED ENGINE POWER (LIMP HOME) MODE"

logic update and inspection for CEL (Check Engine Light) ON with DTC P200A (Intake Manifold Runner Performance - Bank 1) and for P0605 (Engine Control Module - ROM Error) on certain 2015 and 2016 model year Sonata (LF) vehicles equipped with a 2.4L GDI engine. The vehicle may exhibit one or more of the following conditions: DTC P200A (Intake Manifold Runner Performance - Bank 1) ➢ Check Engine Light ON ➢ Slight hesitation or reduced power during acceleration ➢ Automatic transmission upshift hesitation during acceleration ➢ Clicking noise from the intake manifold VCM (Variable Charge Motion) actuator when the engine RPM is increased (2015 MY Only) DTC P0605 (Engine Control Module ROM Error) ➢ Check Engine Light ON ➢ Electronic Stability Control (ESC) Warning Light ON ➢ Limited engine power (Limp Home) mode

added additional vehicles to Service Campaign TZ3. Service Campaign TZ3 provides a procedure to update the ECM software and inspect and (if necessary) replace the VCM actuator on certain 2015-16 Sonata 2.4L vehicles.

conducting a Service Campaign to replace the fuel filler door opener on certain 2015 Model Year Sonata and Sonata Hybrid vehicles. Service Campaign TZ8 provides a procedure to replace the fuel filler door opener.

WITH DIAGNOSTIC TROUBLE CODE (DTC) P0010, INTAKE CAMSHAFT POSITION ACTUATOR CIRCUIT. MODEL 2015 SONATA. *PE

MODEL 2015 SONATA. *PE

recommended safe chemical products.

chemical products.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

system (Gen 1).

DUE TO PREMATURELY WEARING OF AXLE SPLINES AND IMPROPERLY MANUFACTURED, MODEL 2015 SONATA. *PE

contain defective ZF-TRW airbag control units (ZF-TRW ACUs) that are vulnerable to a condition called electrical overstress, which may cause the vehicles airbags and other safety features to fail during a collision. Hyundai has not been found liable for any claims alleged in the lawsuit. Instead, Hyundai reached a voluntary settlement (referred as the Settlement or the proposed Settlement) to avoid lengthy litigation and provide relief to people who own ed or leased Class Vehicles in the United States and U.S. Territories. Class Members may be entitled to compensation if they submit valid and timely Claims.

Module) to revise the OEM Hyundai burglar alarm system operation and ignition start logic and 2) Install two anti-theft decals for the front windows. Additional decals may also be installed in the rear windows at customers discretion.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

injection control logic to compensate for O2 sensor aging and control tailpipe emissions within applicable standards.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows

State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

AIRBAG WARNING LIGHT AND IF SUFFICIENT VIBRATION AT TIME OF DIAGNOSTIC PERIOD, SRSCM IS ERRONEOUSLY DETECTED. MODEL 2015 SONATA. *PE

panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years and unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.

Santa Fe Sport, 2019 model year Santa Fe, 2021 2023 model year Santa Fe Hybrid, and 2020 2023 model year Palisade vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years with unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.

hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer, or has a branded or similar title under any states law.

fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has been previously declared a total loss, and/or sold for salvage by a financial institution or insurer, and/or has a branded or similar title under any states law.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

Follow the procedure in the bulletin to inspect the trunk lid opening height, and replace the torsion bars if required. The warranty coverage for the trunk lid torsion bars has been extended to 78 months or 78,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

This bulletin describes the procedure to replace the trunk latch base.

Follow the procedure in the bulletin to inspect the trunk lid opening height and replace the torsion bars if required. The warranty coverage for the trunk lid torsion bars has been extended to 78 months or 78,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

Follow the procedure in the bulletin to inspect the trunk lid opening height and replace the torsion bars if required.

date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.

In these instances it is recommended to replace the outside mirror actuator only, not the entire outside mirror assembly.

moving glass seal.

(transmission clutch slip in gear above limit) listed on Page 2.

This bulletin outlines the procedures for diagnosing clutch judder, updating the Transmission Control Unit (TCU) with revised logic, and/or replacing the Double Clutch.

This bulletin outlines the procedures for diagnosing clutch judder, updating the Transmission Control Unit (TCU) with revised logic, and/or replacing the Double Clutch.

Eco vehicles, 2016-2017 model year Tucson vehicles, and 2016-2017 model year Veloster vehicles equipped with a Dual Clutch Transmission.

OEM (new) and remanufactured automatic transmissions:

slipping more than 200 rpm in gear).

slipping more than 200 rpm in gear).

when replacing the Dual Clutch Transmission (DCT) with updated clutch material. This bulletin also provides a method of identifying transmissions with the updated F850 clutch material.

measure shift engagement time.

This bulletin provides the diagnostic procedures to correct this condition.

converter is fully installed in the transmission. If this is not done, the oil pump may be damaged.

TRANSMISSION (DCT).

THIS BULLETIN PROVIDES THE PROCEDURES NECESSARY TO RESET (ERASE) AND RELEARN THE PCM/TCM ADAPTIVE VALUES. AFTER THE FOLLOWING REPAIRS HAVE BEEN COMPLETED, THE PCM/TCM ADAPTIVE VALUES MUST BE RESET IN ORDER TO PROVIDE OPTIMUM SHIFT QUALITY. IF THE PROCEDURE IS NOT PERFORMED, THE TRANSMISSION MAY EXPERIENCE A SHIFT FLARE OR HARSH SHIFT. H REPLACE AUTOMATIC TRANSAXLE OR PCM/TCM H REPROGRAM OR EXCHANGE A PCM/TCM FROM ANOTHER VEHICLE"

THIS BULLETIN PROVIDES THE DIAGNOSTIC PROCEDURES TO CORRECT THIS CONDITION.

THE ATF LEVEL MUST BE CHECKED BY THE FOLLOWING PROCEDURE.

The ATF level must be checked by the following procedure: NOTICE Use only ATF meeting the SP-IV specification approved by Hyundai. DO NOT use SP-III or other ATF which may result in degradation of shift quality or transaxle durability.

Apple CarPlay and Android Auto feature. This bulletin describes how to transfer the update software to a storage drive (USB or SD Card) and perform the software installation into the audio system.

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.

This procedure is specifically for the clock date and time not displaying which started appearing around August 17, 2019. Other similar concerns which were opened before this date are a different root cause and will not be resolved by this information. An example of the clock concern is shown in the screenshot below:

This procedure is specifically for the clock date and time not displaying which started appearing around August 17, 2019. Other similar concerns which were opened before this date are a different root cause and will not be resolved by this information. An example of the clock concern is shown in the screenshot below:

pop-up message shown (intermittently) after every Head Unit boot up.

AM>FM>SXM (intermittently) on its own.

Detection (BSD) feature, the trailer may interfere with the BSD system operation resulting in cancellation of the BSD operation. When this occurs, a ?BSD canceled? message is displayed in the vehicle?s instrument cluster. The ?BSD canceled? message remains on even if the customer manually disables the BSD system, and may result in customer complaints. This bulletin provides the service procedure to update the system software to turn off the ?BSD canceled? message when the BSD system is manually disabled.

the inability to set the clock or view it on the top of the screen.

Detection (BSD) feature, the trailer may interfere with the BSD system operation resulting in cancellation of the BSD operation. When this occurs, a ?BSD canceled? message is displayed in the vehicle?s instrument cluster. The ?BSD canceled? message remains on even if the customer manually disables the BSD system, and may result in customer complaints. This bulletin provides the service procedure to update the system software to turn off the ?BSD canceled? message when the BSD system is manually disabled.

DE-ACTIVATED FOR THE FOLLOWING REASONS: H A CUSTOMER WHO INITIALLY WAIVES BLUE LINK ENROLLMENT, AND THEN DECIDES TO ENROLL AFTER PURCHASE OF VEHICLE. H A CUSTOMER WHO ALLOWS ALL PACKAGES OF THEIR BLUE LINK SUBSCRIPTION TO EXPIRE AND THEN WISHES TO RE-SUBSCRIBE TO BLUE LINK. H A CUSTOMER WHO DID NOT ENROLL IN BLUE LINK WITHIN THE FIRST 30 DAYS OF OWNERSHIP (AT WHICH TIME THE DEVICE BECOMES INACTIVE), BUT THEN DECIDES TO ENROLL. H A SUBSEQUENT OWNER WHO WISHES TO ENROLL IN BLUE LINK."

APPLE CARPLAY AND ANDROID AUTO FEATURE. THIS BULLETIN DESCRIBES HOW TO TRANSFER THE UPDATE SOFTWARE TO A STORAGE DRIVE (USB OR SD CARD) AND PERFORM THE SOFTWARE INSTALLATION INTO THE AUDIO SYSTEM.

Based on the Class Action, customers are eligible for certain settlement benefits. Please see attached for details. Impacted vehicles are also noted below. For further information regarding settlement benefits and contacts, please review the dealer notification per the attached. It is also available on Hyundaidealer.com under Hyundai Tech Info > Service News.

Based on the Class Action, customers are eligible for certain settlement benefits. Impacted vehicles are also noted below. For further information regarding settlement benefits and contacts, please review the corresponding dealer notification. It is available on Hyundaidealer.com under Hyundai Tech Info > Service News.

DUE TO A MANUFACTURING ERROR, THE SECOND STAGE FOR THE AIRBAG MAY NOT HAVE BEEN PROPERLY INSTALLED IN SOME VEHICLES. IN THE EVENT OF A COLLISION REQUIRING FRONTAL SECOND STAGE AIRBAG DEPLOYMENT, THE DRIVER'S SECOND STAGE AIRBAG WILL NOT DEPLOY, INCREASING THE RISK OF INJURY. THIS BULLETIN DESCRIBES THE PROCEDURE TO REPLACE THE DRIVER AIRBAG (DAB) TO CORRECT THIS CONDITION.

THE SUNROOF ASSEMBLY INCORPORATES A WIND DEFLECTOR TO HELP REDUCE WIND NOISE IN THE PASSENGER COMPARTMENT WHEN THE SUNROOF IS OPEN. IF THE WIND DEFLECTOR BECOMES PARTIALLY DETACHED FROM ITS MOUNTING BRACKET WHILE THE SUNROOF IS OPEN, THE DEFLECTOR CAN INTERFERE WITH THE CLOSING OF THE MOVEABLE SUNROOF PANEL. IN SOME CASES THIS INTERFERENCE CAN RESULT IN THE SUNROOF PANEL DETACHING FROM ITS MOUNTING TABS. IF THE SUNROOF PANEL DETACHES WHILE THE VEHICLE IS IN MOTION, THE PANEL COULD BECOME AN OBSTACLE TO OTHER DRIVERS, INCREASING THE RISK OF A CRASH.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

diagnosing and conducting alignment-related repairs for all models and model years.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

This bulletin provides information on how to diagnose the yoke noise and replace the rack support yoke assembly.

*LJ

VEHICLES, CORRECTING INTERMITTENT FALSE ILLUMINATION. MODEL 2015 SONATA. *PE