2022 Hyundai Sonata Hybrid TSBs

This bulletin outlines the combustion chamber cleaning procedure for vehicles diagnosed with this condition. All internal combustion engines consume some engine oil during normal operation, depending on driving conditions and mileage, and this procedure should only be performed when deemed necessary based on inspection and diagnosis of the vehicle as outlined in TSB 26-EM-015H, Engine Oil Consumption Inspection & Repair Guidelines, or the latest revision.

This bulletin provides the inspection and repair procedures for vehicles exhibiting this condition. All internal combustion engines consume engine oil as part of normal engine operation. Oil consumption rates may vary based on mileage, operating conditions, driving habits, and maintenance history. Hyundai recommends following the prescribed maintenance schedule and periodically checking the engine oil level using the dipstick to maintain proper engine oil level.

a warning lamp for DTC P218100 (Cooling System Performance) related to the Integrated Thermal-Management Module (ITM). Follow the service procedure in this bulletin to install a spring onto the thermostat within the ITM, in order to prevent premature opening, and perform an ECU software update on affected vehicles.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

from the exhaust due to an internal leak at the Exhaust Heat Recovery System (EHRS) portion of the center muffler assembly. Follow the procedure outlined in this bulletin to repair this condition after confirming EHRS is leaking internally.

or symptoms listed below, refer to the Service Procedure to diagnose the condition. DIAGNOSTIC TROUBLE CODES: P070500 - Transmission range sensor circuit malfunction P070512 - Transmission range sensor circuit malfunction P070514 - Transmission range sensor circuit malfunction P07051C - Transmission range sensor circuit malfunction P070600 - Transmission range sensor circuit range/performance P070661 - Transmission range sensor circuit range/performance P070696 - Transmission range sensor circuit range/performance SYMPTOMS: Malfunction Indicator Light (MIL) illuminated 5th gear fail-safe Intermittently wont shift into D or R Intermittently wont shift out of Park Intermittent ly no engine cr ank/n o start in P or N with or without MIL or DTC.

for 2020-2023MY Sonata Hybrid (DN8 HEV) vehicles to improve the coolant filling mode by discharging air bubbles.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

software update on certain 2022-2023MY Sonata Hybrid (DN8 HEV) vehicles. This software updates the DTC monitoring logic for C240201 Motor Electrical.

the Service Procedure and replace the valve body internal harness and the input/output speed sensor.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

the Service Procedure and replace the related solenoid and harness.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

the Service Procedure and replace the harness with an integrated oil temperature sensor.

Procedure to diagnose the condition. DIAGNOSTIC TROUBLE CODES: P070500 - Transmission range sensor circuit malfunction P070512 - Transmission range sensor circuit malfunction P070514 - Transmission range sensor circuit malfunction P07051C - Transmission range sensor circuit malfunction P070600 - Transmission range sensor circuit range/performance P070661 - Transmission range sensor circuit range/performance P070696 - Transmission range sensor circuit range/performance SYMPTOMS: Malfunction Indicator Light (MIL) illuminated 5th gear fail-safe No gear indication in cluster Intermittently wont shift into D or R Intermittently wont shift out of Park Intermittent ly no engine cr ank/no start in P or N with or without MIL or DTC.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

system.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB. The NAU website is https://update.hyundai.com/US/EN/navigationUpdate. For certain models equipped with a relevant Bluelink package, the software may be downloaded and applied via OTA update.

system.

system.

when entering radio mode and/or displays a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

system.

when entering radio mode and/or displays a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

voltage condition.

light due to DTC Code P1BB20 (12V Lithium Battery Cell Voltage High). The California Air Resources Board has determined that these vehicles may be releasing air pollutants which exceed Federal and California standards.

Hybrid (CN7 HEV), Sonata Hybrid (DN8 HEV), and Tucson Hybrid (NX4 HEV) vehicles that may exhibit a warning light with DTC P1BB200 and enter Limp Mode.

light due to DTC Code P1BB20 (12V Lithium Battery Cell Voltage High). Follow the procedure in TSB 25-01-010H (or latest version) to perform the update the Battery management System (BMS) software.

Hybrid (CN7 HEV), Sonata Hybrid (DN8 HEV), and Tucson Hybrid (NX4 HEV) vehicles that may exhibit a warning light with DTC P1BB20.

light due to DTC Code P1BB20 (12V Lithium Battery Cell Voltage High). Follow the procedure in TSB 24-01-054H (or latest version) to perform the update the Battery management System (BMS) software.

Hybrid (CN7 HEV), Sonata Hybrid (DN8 HEV), and Tucson Hybrid (NX4 HEV) vehicles that may exhibit a warning light with DTC P1BB20.

improve shift quality, judder and hesitation when accelerating.

If you are servicing a vehicle with any symptoms listed below or DTCs (listed on Page 2) , follow the Service Procedure on Page 3. SYMPTOMS: Shifter System Malfunction displayed in the cluster Wont shift into or out of gear or wont shift out of Park Incorrect gear display in cluster and/or wont start

The current version of Google Maps has 10 times the data transmission compared to the previous version. As a countermeasure, an update with a frame skip logic has been added to resolve the data congestion with Google Maps.

or symptoms listed below, refer to the Service Procedure to diagnose the condition.

If you are servicing a vehicle with any symptoms or DTC listed below, follow the Service Procedure, Page 2.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

drivers-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

counterfeit driverside airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or noncertified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

(DATC) software to help improve coolant flow to the Exhaust Heat Recovery System (EHRS).

(DATC) software to help improve coolant flow to the Exhaust Heat Recovery System (EHRS).

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.