2017 Hyundai Sonata Hybrid TSBs

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

manufactured, marketed, sold, and/or leased with an engine defect that can result in sudden engine seizure, stalling, engine failure, and in some circumstances, engine fire, and that some owners and lessees of Class Vehicles have been improperly denied repairs under warranty. Neither HMA nor Hyundai Motor Company have been found liable for any of the claims alleged in the lawsuit. The parties have instead reached a voluntary settlement (the Settlement) to avoid lengthy litigation and to provide owners of Class Vehicles certain benefits.

reduced power steering assist and/or motor driven power steering (MDPS) warning lamp has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first. Refer to the TSB 23-ST-003H (or latest version) for warranty, service parts information, and diagnostic information outlined in the bulletin.

power steering assist and/or motor driven power steering (MDPS) warning lamp has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first. Refer to the warranty, service parts information, and diagnostic information outlined in this bulletin.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

abnormal noise, or no crank/no start condition related to connecting rod bearing wear or damage. This Dealer Best Practice outlines the service process to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results, as well as related warranty coverage for the conditions outlined above.

concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

bearing wear has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. Commercial entities and individuals engaged in the buying, selling, leasing, or renting of motor vehicles, as well as salvaged vehicles, are ineligible for the extended warranty.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

noise before potentially severe engine damage occurs on certain 2017-2018 model year Sonata Hybrid/Plug-In vehicles.

DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

power steering assist and/or motor driven power steering (MDPS) warning lamp has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first. Refer to the warranty, service parts information, and diagnostic information outlined in this bulletin.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

reduced power steering assist and/or motor driven power steering (MDPS) warning lamp has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first.

before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing

Hybrid (LF HEV) and Sonata Plug-In Hybrid (LF PHEV) vehicles with DTC P2600, causing an HEV and/or MIL warning lamp illumination.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.

as separate components.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.

as separate components.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

Check Engine light on DTC P0880/P088000 - TCM Power signal error open/short Transmission stuck in 4th gear fail-safe Harsh shift into Reverse and Drive

Evaporative System (EVAP) - Very Small Leak stored. Salt particulate deposit can form inside the Natural Vacuum Leak Detection (NVLD) sensor which may cause intermittent operation prompting the DTC P0456 and check engine light. This bulletin provides the procedure to replace the NVLD sensor with an updated Air Filter Kit to help prevent entry of the salt particulates.

System (EVAP) - Very Small Leak stored. These conditions primarily occur in the California coastal areas that are subject to marine layer cloud cover. Salt particulate deposit can form inside the Natural Vacuum Leak Detection (NVLD) sensor which may cause intermittent operation prompting the DTC P0456 and check engine light. This bulletin provides the procedure to install a new Air Filter Kit with an updated filter to help prevent entry of the salt particulates. In addition, replace NVLD sensor if DTC P0456 found stored in the Engine Control Module (ECM).

the repair procedure and replace the related solenoid and oil pressure harness.

the repair procedure and replace the related solenoid and oil pressure harness.

the repair procedure and replace the related solenoid and oil pressure harness.

as separate components.

The PRA is equipped with a main relay and High Voltage Cable, which in some instances may have a loose connection. If the vehicle continues to operate in this condition, a loose connection could cause a no start condition or a Check Engine and Hybrid Warning Light On with either or both of these DTCs stored: DTC P1B77 High Voltage Battery Precharging Fault DTC P1990 Oil Pump Unit Input High Voltage Wiring Line Open This bulletin describes the procedure to inspect the PRA, High Voltage Cable, and main relays and replace them if necessary.

This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.

? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear indication in cluster ?Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.

follow the repair procedure and replace the related solenoid and oil pressure harness

as separate components.

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

This update allows for the driving information to be updated in the Electric Motor Use chart. The software update will take approximately 35 minutes to complete.

This update allows for the driving information to be updated in the Electric Motor Use chart. The software update will take approximately 35 minutes to complete.

Service campaign T2M provides a service procedure to replace the inhibitor switch on certain 2017-18 Santa Fe Sport, 2017 Santa Fe, 2017-18 Tucson, 2017 Azera, 2017 Sonata, Sonata Hybrid & Plug-in.

? Diagnostic trouble codes: ? P0705 - Range switch sensor circuit ? P0706 - Range switch range/performance ? P0707 - Range switch - open circuit ? P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ? Malfunction Indicator Light (MIL) illuminated ? 4th gear fail-safe ? No gear indication in cluster ? Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.

Start if the pulley becomes loose at the Hybrid Starter Generator (HSG) shaft.

function for the Bluelink service is operating properly.

function for the Bluelink service is operating properly.

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.

This procedure is specifically for the clock date and time not displaying which started appearing around August 17, 2019. Other similar concerns which were opened before this date are a different root cause and will not be resolved by this information. An example of the clock concern is shown in the screenshot below:

This procedure is specifically for the clock date and time not displaying which started appearing around August 17, 2019. Other similar concerns which were opened before this date are a different root cause and will not be resolved by this information. An example of the clock concern is shown in the screenshot below:

pop-up message shown (intermittently) after every Head Unit boot up.

clock or view it on the top of the screen.

system frequently losing a Bluetooth connection with Apple iPhone devices.

Detection (BSD) feature, the trailer may interfere with the BSD system operation resulting in cancellation of the BSD operation. When this occurs, a ?BSD canceled? message is displayed in the vehicle?s instrument cluster. The ?BSD canceled? message remains on even if the customer manually disables the BSD system, and may result in customer complaints. This bulletin provides the service procedure to update the system software to turn off the ?BSD canceled? message when the BSD system is manually disabled.

Detection (BSD) feature, the trailer may interfere with the BSD system operation resulting in cancellation of the BSD operation. When this occurs, a ?BSD canceled? message is displayed in the vehicle?s instrument cluster. The ?BSD canceled? message remains on even if the customer manually disables the BSD system, and may result in customer complaints. This bulletin provides the service procedure to update the system software to turn off the ?BSD canceled? message when the BSD system is manually disabled.

APPLE CARPLAY AND ANDROID AUTO FEATURE. THIS BULLETIN DESCRIBES HOW TO TRANSFER THE UPDATE SOFTWARE TO A STORAGE DRIVE (USB OR SD CARD) AND PERFORM THE SOFTWARE INSTALLATION INTO THE AUDIO SYSTEM.

contain defective ZF-TRW airbag control units (ZF-TRW ACUs) that are vulnerable to a condition called electrical overstress, which may cause the vehicles airbags and other safety features to fail during a collision. Hyundai has not been found liable for any claims alleged in the lawsuit. Instead, Hyundai reached a voluntary settlement (referred as the Settlement or the proposed Settlement) to avoid lengthy litigation and provide relief to people who own ed or leased Class Vehicles in the United States and U.S. Territories. Class Members may be entitled to compensation if they submit valid and timely Claims.

State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.

by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.

The affected vehicles include: Certain 2016-2017MY Sonata Hybrid (LF HEV) vehicles Hyundai is initiating this action to ensure the quality of its vehicles and the continued satisfaction of Hyundai customers.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

and safe environmental recycling using Hyundai?s authorized vendor Kinsbursky Brothers Intl. (KBI).

and safe environmental recycling using Hyundai?s authorized vendor Kinsbursky Brothers Inc. (KBI).

and safe environmental recycling using Hyundai?s authorized vendor Kinsbursky Brothers Inc. (KBI).

(transmission clutch slip in gear above limit) listed on Page 2.

OEM (new) and remanufactured automatic transmissions:

slipping more than 200 rpm in gear).

slipping more than 200 rpm in gear).

measure shift engagement time.

This bulletin provides the diagnostic procedures to correct this condition.

A possible symptom is Diagnostic Trouble Code P0705 (Transmission Range Sensor Circuit).

converter is fully installed in the transmission. If this is not done, the oil pump may be damaged.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

This bulletin describes the procedure to replace the trunk latch base.

When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

recommended safe chemical products.

chemical products.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

exhibits Diagnostic Trouble Code (DTC) C120B/D or C160A.

This procedure applies when any air is introduced into the Active Hydraulic Boost (AHB) system, which consists of the pressure supply unit (PSU), and the integrated brake actuation unit (IBAU). Improper bleeding of the brake system can result in the presence of air, which may reduce braking effectiveness.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

diagnosing and conducting alignment-related repairs for all models and model years.

Based on the Class Action, customers are eligible for certain settlement benefits. Please see attached for details. Impacted vehicles are also noted below. For further information regarding settlement benefits and contacts, please review the dealer notification per the attached. It is also available on Hyundaidealer.com under Hyundai Tech Info > Service News.

Based on the Class Action, customers are eligible for certain settlement benefits. Impacted vehicles are also noted below. For further information regarding settlement benefits and contacts, please review the corresponding dealer notification. It is available on Hyundaidealer.com under Hyundai Tech Info > Service News.

the salt particulates on certain 2016-2019 Sonata Hybrid (LF HEV) vehicles.

compressors equipped in hybrid electric vehicles, plug-in hybrid electric vehicles, and electric vehicles.

compressors equipped in hybrid electric vehicles, plug-in hybrid electric vehicles, and electric vehicles.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

This bulletin provides information on how to diagnose the yoke noise and replace the rack support yoke assembly.