2023 Hyundai Santa Fe TSBs

This bulletin outlines the combustion chamber cleaning procedure for vehicles diagnosed with this condition. All internal combustion engines consume some engine oil during normal operation, depending on driving conditions and mileage, and this procedure should only be performed when deemed necessary based on inspection and diagnosis of the vehicle as outlined in TSB 26-EM-015H, Engine Oil Consumption Inspection & Repair Guidelines, or the latest revision.

This bulletin provides the inspection and repair procedures for vehicles exhibiting this condition. All internal combustion engines consume engine oil as part of normal engine operation. Oil consumption rates may vary based on mileage, operating conditions, driving habits, and maintenance history. Hyundai recommends following the prescribed maintenance schedule and periodically checking the engine oil level using the dipstick to maintain proper engine oil level.

have DTC U028700 (Lost Communication With Trans Fluid Pump Module) set by the transmission Electric Oil Pump (EOP). This DTC can cause the Idle Stop & Go (ISG) system to become inoperative. Follow the procedure in this bulletin to replace the Electric Oil Pump on affected vehicles.

Electronic Control Unit (ECU), resulting in an illuminated Check Engine warning lamp. Follow the procedure in this TSB to replace the Integrated Thermal Management (ITM) module and update both the Engine Control Module (ECM) and Transmission Control Module (TCM) if applicable. Follow the flowchart in this TSB to update the appropriate modules.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

for 2021-2023MY Santa Fe (TMa) vehicles to improve operation of the Idle Stop and Go (ISG) system. Under certain circumstances the vehicle may not restart after the ISG system has engaged and requires a manual restart due to the lack of intake manifold pressure recovery.

or symptoms listed below, refer to the Service Procedure to diagnose the condition. DIAGNOSTIC TROUBLE CODES: P070500 - Transmission range sensor circuit malfunction P070512 - Transmission range sensor circuit malfunction P070514 - Transmission range sensor circuit malfunction P07051C - Transmission range sensor circuit malfunction P070600 - Transmission range sensor circuit range/performance P070661 - Transmission range sensor circuit range/performance P070696 - Transmission range sensor circuit range/performance SYMPTOMS: Malfunction Indicator Light (MIL) illuminated 5th gear fail-safe Intermittently wont shift into D or R Intermittently wont shift out of Park Intermittent ly no engine cr ank/n o start in P or N with or without MIL or DTC.

transmissions (8WDCT) and associated transmission control unit (TCU). These changes only apply to vehicles equipped with Theta 2.5T engines. Certain transmissions (indicated by a new part number) have received an improved clutch spring. The correct TCU software update must be matched with the correct corresponding 8WDCT hardware, otherwise drivability concerns may occur.

service procedure and replace the related solenoid and harness.

Service Procedure to diagnose the condition. DIAGNOSTIC TROUBLE CODES: P070500 - Transmission range sensor circuit malfunction P070512 - Transmission range sensor circuit malfunction P070514 - Transmission range sensor circuit malfunction P07051C - Transmission range sensor circuit malfunction P070600 - Transmission range sensor circuit range/performance P070661 - Transmission range sensor circuit range/performance P070696 - Transmission range sensor circuit range/performance SYMPTOMS: Malfunction Indicator Light (MIL) illuminated 5th gear fail-safe Intermittently wont shift into D or R Intermittently wont shift out of P Intermittent ly no engine crank in P or

service procedure and replace the related solenoid and harness.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

equipped with an 8-speed wet dual clutch transmission (8WDCT). The software update revises the touch point learning variation, improving drivability and judder symptoms. Some 8WDCTs (indicated by a new part number) received an updated clutch spring. The correct TCU software update must be matched with the correct corresponding 8WDCT hardware, otherwise, drivability concerns may occur. This service procedure should be performed prior to any 8WDCT replacements done for drivability/judder concerns.

clutch transmission (8WDCT) when the vehicle sets one of the high pressure electric oil pump (HP EOP) DTCs listed below. This bulletin provides instructions to replace the 8WDCT.

one of the DTCs listed below, related to the high pressure electric oil pump (HP EOP). Follow the procedures in this TSB to update the Transmission Control Unit (TCU) to the latest sensorless logic on affected vehicles, and then perform air bleeding and transmission learning.

specification that could lead to a higher mileage durability issue regarding the transmission oil pump. Follow the steps listed below to inspect the transmission. Replace the transmission if needed.

equipped with an 8-speed wet dual clutch transmissions (8WDCT) that improves the touch point learning variation. Certain 8WDCTs (indicated by a new part number) received an improved clutch spring. The correct TCU software update must be matched with the correct corresponding 8WDCT hardware, otherwise drivability concerns may occur.

If replacement of the SBW button is required due to one or more button plating peeling, replace the button(s) with a new one. Do not replace the complete SBW lever.

If you are servicing a vehicle with any symptoms listed below or DTCs (listed on Page 2) , follow the Service Procedure on Page 3. SYMPTOMS: Shifter System Malfunction displayed in the cluster Wont shift into or out of gear or wont shift out of Park Incorrect gear display in cluster and/or wont start

The current version of Google Maps has 10 times the data transmission compared to the previous version. As a countermeasure, an update with a frame skip logic has been added to resolve the data congestion with Google Maps.

or symptoms listed below, refer to the Service Procedure to diagnose the condition.

Pump) connector when servicing the 8-speed wet dual clutch transmission (8WDCT). If moisture enters the HF EOP connector, this can result in corrosion and insufficient connection of the terminals.

(DCT) and associated transmission control module (TCM). Additional steps, not in the service manual, are required within GDS prior to replacing the DCT/TCM, otherwise drivability concerns and/or DTCs may occur.

Navigation Map and Software Update. The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2026 1st Navigation Map and Software Update Key Improvements and Additional Improvements tables in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

system.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB. The NAU website is https://update.hyundai.com/US/EN/navigationUpdate. For certain models equipped with a relevant Bluelink package, the software may be downloaded and applied via OTA update.

system.

system.

system.

when entering radio mode and/or a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. If a horn needs to be replaced, follow the instructions within this Technical Service Bulletin (TSB)26-BE-001H-2 to install the latest design. Please note that any vehicles under 10 years/120,000 miles are covered by this TSB, even if vehicle is with original warranty of 5 years/60,000 miles.

Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. If a horn needs to be replaced, follow the instructions within this TSB to install the latest design. Please note that any vehicles under 10 years / 120,000 miles are covered by this TSB, even if vehicle is within original warranty of 5 years / 60,000 miles.

Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. If a horn needs to be replaced, follow the instructions within this Technical Service Bulletin (TSB) 26-BE-001H-1 to install the latest design. Please note that any vehicles under 10 years/120,000 miles are covered by this TSB, even if vehicle is with original warranty of 5 years/60,000 miles.

Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. If a horn needs to be replaced, follow the instructions within this TSB to install the latest design. Please note that any vehicles under 10 years/120,000 miles are covered by this TSB, even if vehicle is within original warranty of 5 years/60,000 miles.

Hyundai is extending the warranty coverage for the horn replacement under this condition to 10 years or 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. If a horn needs to be replaced, follow the instructions within Technical Service Bulletin (TSB) to install the latest design. Please note that any vehicles under 10 years/120,000 miles are covered by this TSB, even if vehicle is within original warranty of 5 years/60,000 miles.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

This bulletin provides the procedure to perform an inspection on the starter magnetic switch for potential freezing and, if necessary, replace the starter magnetic switch (solenoid) assembly.

illumination for a diagnostic trouble code P2181 that is related to the Integrated Thermal Management Module (ITM). Follow the service procedure outlined in this bulletin to replace the ITM.

Follow the procedure outlined in this TSB to replace the oil level sensor and gasket to complete the service campaign.

drivers-side airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN). These inflators were not supplied, approved, or authorized by the vehicle manufacturers and have primarily been found in vehicles that previously experienced a crash and underwent airbag replacement using non-genuine parts. These dangerous inflators have ruptured during deployment, posing a serious risk of injury or death due to metal fragments entering the vehicle cabin. To date, Hyundai is aware of three people who have died while driving a Hyundai vehicle with one of these substandard replacement airbag inflators that deployed in what likely would have been a survivable crash. NHTSA has issued a public advisory urging vehicle owners and service professionals to have vehicles inspected if there is reason to believe that a non-genuine replacement airbag may have been installed. Vehicles with salvage or rebuilt titles, prior airbag deployments, or unknown repair histories may present a higher risk. NHTSA strongly cautions against self-inspection by vehicle owners and recommends inspection by trained technicians.

counterfeit driverside airbag inflators manufactured by Jilin Province Detiannuo Automobile Safety System Co., Ltd. (DTN), that have been identified in U.S. vehicles following prior crashes, theft, or noncertified airbag replacements. These inflators are not approved for use, may rupture during deployment, and have caused serious injuries and fatalities. Please see attached announcement, provided by NHTSA, for more details.

Plug-In Hybrid vehicles may experience an inoperable horn that may be caused by foreign substances causing internal parts to oxidize. At Hyundai, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, the warranty coverage for the horn assemblies under these conditions has been extended to 10 years/ 120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

This bulletin describes the procedure to inspect the brakes, resurface or replace and perform a brake burnishing procedure.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

and newer Santa Fe (TMA), 2021MY and newer Santa Fe Hybrid (TM HEV), 2022MY and newer Santa Fe Plug-In Hybrid (TM PHEV), and 2019MY and newer Palisade (LX2) vehicles equipped with surround view monitoring (SVM) system.