2010 Hyundai Santa Fe TSBs

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

manufactured, marketed, sold, and/or leased with an engine defect that can result in sudden engine seizure, stalling, engine failure, and in some circumstances, engine fire, and that some owners and lessees of Class Vehicles have been improperly denied repairs under warranty. Neither HMA nor Hyundai Motor Company have been found liable for any of the claims alleged in the lawsuit. The parties have instead reached a voluntary settlement (the Settlement) to avoid lengthy litigation and to provide owners of Class Vehicles certain benefits.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

abnormal noise, or no crank/no start condition related to connecting rod bearing wear or damage. This Dealer Best Practice outlines the service process to inspect the vehicle and replace the engine or update the engine ECU software based on the inspection results, as well as related warranty coverage for the conditions outlined above.

concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

bearing wear has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners. Commercial entities and individuals engaged in the buying, selling, leasing, or renting of motor vehicles, as well as salvaged vehicles, are ineligible for the extended warranty.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

DTC P1326 and/or an engine concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

concern/noise related to connecting rod bearing wear or damage. Follow the procedure to inspect the vehicle and replace the engine and/or update the engine ECU software (if new ROM is available) based on the inspection results.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.

is related to connecting rod bearing wear, has been extended to 15 years or 150,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected.

Check Engine light on DTC P0880/P088000 - TCM Power signal error open/short Transmission stuck in 4th gear fail-safe Harsh shift into Reverse and Drive

the repair procedure and replace the related solenoid and oil pressure harness.

the repair procedure and replace the related solenoid and oil pressure harness.

the repair procedure and replace the related solenoid and oil pressure harness.

This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.

follow the repair procedure and replace the related solenoid and oil pressure harness

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

? Diagnostic trouble codes: ? P0705 - Range switch sensor circuit ? P0706 - Range switch range/performance ? P0707 - Range switch - open circuit ? P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ? Malfunction Indicator Light (MIL) illuminated ? 4th gear fail-safe ? No gear indication in cluster ? Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.

MODULE ARE SET FOR THE APPLICABLE VEHICLE, AND IF NECESSARY, HOW TO MAKE ADJUSTMENTS TO THESE SETTINGS.

AND PLACES ON ENGINE TO MAXIMIZE EFFICIENCY. MODEL 2010-2012 SANTA FE. *PE

RESULTED IN RANGE SWITCH SENSOR CIRCUIT (P0705), OPEN CIRCUIT (P0707), SWITCH RANGE/PERFORMANCE (P0706), SHORT CIRCUIT OR MULTIPLE INPUTS (P0708), IMPOSSIBLE ENGINE START (P OR N), MALFUNCTION INDICATOR LIGHT (MIL) ILLUMINATION. MODEL 2010-2013 SANTA FE, TUCSON, SONATA, ELANTRA, AZERA, ACCENT, VELOSTER TURBO. *PE

PROVIDED, DUE TO DEPOSITS FOUND AT VALVE-TO-BORE INTERFACE. MODELS 2011-2013 ELANTRA, 2010-2013 GENESIS COUPE, 2010-2013 SANTA FE, 2006-2013 SONATA, 2010-2013 TUCSON. *PE

*JS

*RM

THIS IS CAUSED BY INCORRECT INPUT AND OUTPUT SPEED SENSORS. *RM

2010-2011 SANTE FE. *RM

PROVIDES A PROCEDURE THAT WILL REPAIR OR PREVENT AN INTERMEDIATE SHAFT NOISE CONDITION ON CERTAIN VEHICLES WITH 2.4L ENGINES WITH AUTOMATIC TRANSMISSIONS BUILT BETWEEN 10/15/09-03/05/10. *PE UPDATED 4/15/11. *PE

INCORRECT OPERATION OF THE TRANSMISSION SOLENOIDS MAY RESULT IN THE FOLLOWING: CHECK ENGINE LIGHT ILLUMINATED; TRANSAXLE HELD IN 4TH GEAR FAIL SAFE. *PE UPDATED 6/10/11. *PE

THE BLUETOOTH CONTROLS ON THE STEERING WHEEL DO NOT OPERATE, A COUNTERMEASURE WIRING HARNESS IS NOW AVAILABLE TO REMEDY THE CONDITION. AN UPDATED WIRING HARNESS IS NOW PART OF THE ACCESORY TURBO BOOST GAUGE KIT. *PE

INCORRECT OPERATION OF THE TRANSAXLE SOLENOIDS MAY RESULT IN THE FOLLOWING SYMPTOMS-CHECK ENGINE LIGHT ILLUMINATED; TRANSAXLE HELD IN 3RD GEAR FAIL SAFE. *PE

recommended safe chemical products.

chemical products.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

*PE

*RM

OEM (new) and remanufactured automatic transmissions:

slipping more than 200 rpm in gear).

slipping more than 200 rpm in gear).

measure shift engagement time.

This bulletin provides the diagnostic procedures to correct this condition.

converter is fully installed in the transmission. If this is not done, the oil pump may be damaged.

THIS BULLETIN PROVIDES THE PROCEDURES NECESSARY TO RESET (ERASE) AND RELEARN THE PCM/TCM ADAPTIVE VALUES. AFTER THE FOLLOWING REPAIRS HAVE BEEN COMPLETED, THE PCM/TCM ADAPTIVE VALUES MUST BE RESET IN ORDER TO PROVIDE OPTIMUM SHIFT QUALITY. IF THE PROCEDURE IS NOT PERFORMED, THE TRANSMISSION MAY EXPERIENCE A SHIFT FLARE OR HARSH SHIFT. H REPLACE AUTOMATIC TRANSAXLE OR PCM/TCM H REPROGRAM OR EXCHANGE A PCM/TCM FROM ANOTHER VEHICLE"

THIS BULLETIN PROVIDES THE DIAGNOSTIC PROCEDURES TO CORRECT THIS CONDITION.

THE ATF LEVEL MUST BE CHECKED BY THE FOLLOWING PROCEDURE.

The ATF level must be checked by the following procedure: NOTICE Use only ATF meeting the SP-IV specification approved by Hyundai. DO NOT use SP-III or other ATF which may result in degradation of shift quality or transaxle durability.

MODEL 2010-2012 SANTA FE. *PE

MODELS 2010-2013 TUCSON, SANTA FE, 2011-2013 SONATA, ELANTRA, AZERA, 2012-2013 ACCENT, 2013 VELOSTER. *PE

DO NOT REPLACE TRANSMISSION FOR THE DTC. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE RELATED PART. ALSO INCLUDED MODEL AZERA MODEL YEAR 2012. *JS

ALSO INCLUDED MODEL ELANTRA MODEL YEAR 2013. *JS

AUTOMATIC TRANSAXLE SOFTWARE UPDATE. *RM

*PE

State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

(AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.

(AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.

VEHICLES TO CORRECT THE MALFUNCTION INDICATOR LAMP ILLUMINATION. *LJ

REPLACING OF THE PCM AND A POSSIBLE WARRANTY CLAIM. MODELS 2011-2013 ELANTRA, 2010-2013 GENESIS COUPE, 2010-2013 SANTA FE, 2006-2013 SONATA, 2010-2013 TUCSON. *PE

2010-2011 SANTA FE. FRONT COIL SPRING INSTALLATION. *RM UPDATED 10/28/11. *PE UPDATED 1/25/12. *PE

2010-2011 SANTE FE. *RM

(CAMPAIGN TC7). PROVIDES INFORMATION RELATED TO AN ECM SOFTWARE UPDATE TO SOME VEHICLES TO REVISE LOGIC FOR DTC P0111 INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT RANGE/PERFORMANCE. *PE

PROVIDES INFORMATION RELATED TO THE ECM SOFTWARE UPDATE OF VEHICLES WHICH MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP ILLUMINATED WITH ECM (ELECTRONIC CONTROL MODULE) SYSTEM RELATED DTC P0454 (EVAPORATIVE EMISSION SYSTEM-PRESSURE SENSOR INTERMITTENT). *PE

A ROLLOVER SENSOR HAS BEEN INCORPORATED INTO THE SRS CONTROL MODULE (SRSCM) BEGINNING WITH THE 2010 MODEL YEAR SANTA FE AND TUCSON. THE ROLLOVER SENSOR DETERMINES IF IT IS NECESSARY TO DEPLOY SIDE AIR BAGS, CURTAIN AIR BAGS AND SEAT BELT PRETENSIONERS IF A VEHICLE ROLLOVER OCCURS. *PE

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

diagnosing and conducting alignment-related repairs for all models and model years.

EFFECTIVE 6/2/08, FMVSS 110 (FMVSS 110) SETS A THRESHOLD FOR CORRECTING LOAD CAPACITY INFORMATION INDICATED ON TIRE PLACARDS WHEN VEHICLE WEIGHT HAS BEEN INCREASED BEFORE RETAIL SALE. ALL MODELS INCLUDED AFTER 6/2/08. *PE

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

As a precautionary measure, cavity wax coating is applied to the internal surfaces of underbody components, and an undercoating spray is applied to the bottom exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain Santa Fe (CM) vehicles.

As a precautionary measure, cavity wax coating is applied to the internal surfaces of underbody components, and an undercoating spray is applied to the bottom exterior surfaces of specified underbody components. This bulletin describes the procedure to perform this preventative service on certain Santa Fe (CM) vehicles.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

original retail delivery or date of first use, whichever occurs first. This warranty coverage applies to both the original and subsequent owners. Refer to the warranty and service parts information outlined in this bulletin whenever clock spring replacement is required.

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.

INTERMEDIATE SHAFT REPLACEMENT. *RM UPDATED 10/12/11. *PE