2020 Hyundai Palisade TSBs

and Particulate Matter (PM) emission standards. Technical Service Bulletin (TSB) 26-01-010H provides the service procedure to update the emission logic within the Engine Control Module (ECM) to improve engine-out NOx and PM emissions, so they are within permissible specifications. Additionally, improvements to reduce noise during engine start, and enhanced thermostat logic, are also included in the updated ECM software.

and Particulate Matter (PM) emission standards. The service procedure provides an update to the emission logic within the Engine Control Module (ECM) to improve engine-out NOx and PM emissions, so they are within permissible specifications. Additionally, improvements to reduce noise during engine start, and enhanced thermostat logic, are also included in the updated ECM software.

and Particulate Matter (PM) emission standards. This bulletin provides the service procedure to update the emission logic within the Engine Control Module (ECM) to improve engine-out NOx and PM emissions, so they are within permissible specifications. Additionally, improvements to reduce noise during engine start, and enhanced thermostat logic, are also included in the updated ECM software.

installation of a key cylinder reinforcement protector assembly and two anti-theft decals on the front windows. This repair procedure is being provided in addition to the previous Anti-Theft software provided under Service Campaign 993 (TSB 24-01-009H-1).

ignition cylinder protector hardware upgrade is being made available to customers upon request. This supplemental security measure is to be installed at the ignition switch location and provides additional protection against the social media theft method. Vehicles not equipped with an immobilizer during production at the factory are eligible. The repair procedure shall be performed and claimed upon customer request only. Any future repairs to these vehicles in which an installed ignition cylinder protector impacts required parts and/or labor, shall be covered by HMA. Please see TSB 25-01-089H for details.

anti-theft decals on the front windows.

available to owners of eligible models free of charge at authorized Hyundai dealers since early 2023. In addition to the anti-theft software, weve developed a new zinc-reinforced ignition cylinder protector hardware upgrade that can be installed at the ignition cylinder location to provide additional protection against the social media theft method. Because your Hyundai vehicle with the VIN listed above (Subject Vehicle) was not factory-equipped with an engine immobilizer and was previously eligible for the software upgrade, you are now eligible until March 31, 2027 to have the ignition cylinder protector installed if you request it at no cost to you through an authorized Hyundai dealership.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

(LX2) vehicles to reduce the coupling noises when making turns.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

vehicles that were not equipped with an engine immobilizer (called the Class Vehicles) contain design flaws, including the failure to manufacture the Class Vehicles with an anti-theft device called an engine immobilizer, that make them susceptible to theft and damage. Class Vehicles manufactured without an engine immobilizer have traditional turn-key-to-start ignition systems.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. Campaign 9A8 has also been released to provide a revised software update to certain 2018 model year Elantra vehicles. For certain vehicles that cannot be upgraded with the software under Campaign 993, Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealerships.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers an anti-theft ignition cylinder protector to be installed on their vehicle. This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock anti-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), and anti-theft ignition cylinder protector campaign (Campaign 9A5) in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be upgraded with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

or symptoms listed below, refer to the Service Procedure to diagnose the condition. DIAGNOSTIC TROUBLE CODES: P070500 - Transmission range sensor circuit malfunction P070512 - Transmission range sensor circuit malfunction P070514 - Transmission range sensor circuit malfunction P07051C - Transmission range sensor circuit malfunction P070600 - Transmission range sensor circuit range/performance P070661 - Transmission range sensor circuit range/performance P070696 - Transmission range sensor circuit range/performance SYMPTOMS: Malfunction Indicator Light (MIL) illuminated 5th gear fail-safe Intermittently wont shift into D or R Intermittently wont shift out of Park Intermittent ly no engine cr ank/n o start in P or N with or without MIL or DTC.

service procedure and replace the related solenoid and harness.

anti-theft steering wheel lock campaign (Campaign P32), in response to an increase in thefts of certain 2011-2022MY Hyundai vehicles not equipped with engine immobilizers targeted through social media. For certain vehicles that cannot be updated with the software (Campaign 993), Hyundai is offering customers steering wheel locks at the dealer (Campaign P32). This Dealer Best Practices Guide provides information to assist dealership personnel with customer questions relating to the immobilizer software upgrade, window decals and steering wheel lock ant-theft solutions available from HMA through Hyundai dealers.

Follow the procedure outlined in this bulletin to inspect and replace the radiator to correct the condition, if necessary.

in thefts of certain Hyundai vehicles not equipped with engine immobilizers targeted through social media. In November 2021, engine immobilizers became standard on all Hyundai vehicles produced.

service procedure and replace the related solenoid and harness.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

system accordingly during engine short block or sub-assembly replacement.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

This bulletin provides the procedure to update the Integrated Central Control Unit (ICU) software to resolve this condition.

the repair procedure and replace the related input/output speed sensor and harness.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing.

the repair procedure and replace the related solenoid and valve body harness.

wheels: SEL trim with convenience/premium package; all Limited trim) may exhibit a knocking or rattling noise from the rear of the vehicle when driving on bumpy roads at low speeds.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft bearing

The update is to revise the logic for the following DTC: P060148 (Functional Safety Level 2 SW failure) P106D00 (Actuator initialization error) P106D71 (Actuator motor stuck error) U110382 (SBW lever Alive counter error).

The update is for MIL on and the following DTC: P106D00 (Actuator initialization error) P106D71 (Actuator motor stuck error) U110382 (SBW lever Alive counter error).

Procedure to diagnose the condition. DIAGNOSTIC TROUBLE CODES: P070500 - Transmission range sensor circuit malfunction P070512 - Transmission range sensor circuit malfunction P070514 - Transmission range sensor circuit malfunction P07051C - Transmission range sensor circuit malfunction P070600 - Transmission range sensor circuit range/performance P070661 - Transmission range sensor circuit range/performance P070696 - Transmission range sensor circuit range/performance SYMPTOMS: Malfunction Indicator Light (MIL) illuminated 5th gear fail-safe No gear indication in cluster Intermittently wont shift into D or R Intermittently wont shift out of Park Intermittent ly no engine cr ank/no start in P or N with or without MIL or DTC.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

the repair procedure and replace the related solenoid and valve body harness.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.

as separate components.

If bearing noise is heard, follow the procedure in this bulletin to replace the worm shaft assembly.

as separate components.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

Refer to applicable Shop Manual and Owners Manual for additional information.

The update is for MIL on and the following DTC: P106D00 (Actuator initialization error), P106D71 (Actuator motor stuck error) and U110382 (SBW lever Alive counter error).

as separate components.

the repair procedure and replace the related input/output speed sensor and oil pressure harness.

the repair procedure and replace the related oil pressure harness with integrated oil temperature sensor.

the repair procedure and replace the related solenoid and oil pressure harness.

This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.

follow the repair procedure and replace the related oil pressure harness with integrated oil temperature sensor.

follow the repair procedure and replace the related input/output speed sensor and oil pressure harness.

follow the repair procedure and replace the related solenoid and oil pressure harness.

Module) to revise the OEM Hyundai burglar alarm system operation and ignition start logic and 2) Install two anti-theft decals for the front windows. Additional decals may also be installed in the rear windows at customers discretion.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

remote start system may exhibit the horn honking when remote starting the vehicle after receiving the software update. This bulletin provides the procedure to update the remote start module to eliminate the horn honking during remote start operation.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

This bulletin provides the service procedure to update the IBU/BCM (Integrated Body Control Unit/Body Control Module), to revise the OEM Hyundai burglar alarm system operation and ignition start logic, and installation of two anti-theft decals for the front windows.

to the battery SOH (State Of Health) condition will be removed - ISG engagement with satisfied battery SOC (State Of Charge) will remain

or latest version) for vehicles equipped with a Genuine Hyundai Accessory trailer tow hitch and wire harness installed.

This bulletin provides the service procedure to inspect and when necessary perform the power tailgate spindle wire harness revision.

This bulletin provides the service procedure to inspect and when necessary perform the power tailgate spindle wire harness revision.

tailgate may experience a nonoperational condition. This campaign provides service procedures to inspect and when necessary, perform the power tailgate spindle wire harness revision.

tailgate spindle wire harness update.

This bulletin provides the service procedure to inspect and when necessary perform the power tailgate spindle wire harness revision

State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.

A selected Dark Current Control Mode will function when the vehicle is in the key off state, and will not affect vehicle functionality or performance.

by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.

Blind-Spot Collision Warning System? displayed on the instrument cluster. When the BCW Malfunction Indicator Light is ON, the BCW function becomes inoperative. When the BCW Malfunction Indicator Message turns ON, the diagnostic code C270354 (Control Module Slave Calibration) will be triggered.

Blind-Spot Collision Warning System? displayed on the instrument cluster. When the BCW Malfunction Indicator Light is ON, the BCW function becomes inoperative. This bulletin provides the service procedure to update the BCW system software to correct the intermittent BCW Malfunction Indicator Light. NOTE: When the BCW Malfunction Indicator Message turns ON, the diagnostic code C270354 (Control Module Slave Calibration) will be triggered.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

The changes may vary depending on vehicle type, model, and navigation system as described in this TSB.

The changes may vary depending on vehicle type, model, and navigation system. Refer to the 2024 2nd Navigation Map and Software Update Improvements section in this TSB for a list of specific changes. The software can be downloaded via Navigation Updater (NAU) and updated by USB. The NAU website is https://update.hyundai.com/US/EN/navigationUpdate. For certain models equipped with a relevant Bluelink package, the software may be downloaded and applied via OTA update.

when entering radio mode and/or displays a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

when entering radio mode and/or displays a message that reads Uneven Road Ahead, Drive carefully on the cluster along with a warning sound. Follow the procedure outlined in this bulletin to update the AVN software to resolve this condition.

When Wireless CarPlay is disconnected, a pop up message Phone Not Responding. Please reconnect it and try again will appear on the radio screen.

When Wireless CarPlay is disconnected, a pop up message Phone Not Responding. Please reconnect it and try again will appear on the radio screen.

Blind-Spot Collision Warning System displayed on the instrument cluster. This bulletin provides the service procedure to update the BCW system software to correct the intermittent BCW Malfunction Indicator Light.

Blind-Spot Collision Warning System displayed on the instrument cluster. This bulletin provides the service procedure to update the BCW system software to correct the intermittent BCW Malfunction Indicator Light.

condition: Unresponsive radio after multiple uses of voice recognition to perform navigational searches.

Follow the procedure in this bulletin to update the navigation system.

Blind-Spot Collision Warning System displayed on the instrument cluster. When the BCW Malfunction Indicator Light is ON, the BCW function becomes inoperative. This bulletin provides the service procedure to update the BCW system software to correct the intermittent BCW Malfunction Indicator Light.

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.

Follow the procedure in this bulletin to update the navigation system.

panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years and unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.

Santa Fe Sport, 2019 model year Santa Fe, 2021 2023 model year Santa Fe Hybrid, and 2020 2023 model year Palisade vehicles may exhibit excessive paint peeling or bubbling of the primer/paint film on the exterior metal body panels: hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. This warranty extension only applies to factory-applied paint and does not cover collision-related paint repairs or vehicles with a salvaged title. Hyundai is extending the warranty coverage for certain white paint colors under these conditions from 3 years and 36,000 miles, to 10 years with unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners.

hood, fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has ever been declared a total loss or sold for salvage by a financial institution or insurer, or has a branded or similar title under any states law.

fender(s), roof, door(s), quarter panel(s), and tailgate/trunk. The paint warranty coverage for affected vehicles has been extended to 10 years/unlimited miles from the date of original retail delivery or date of first use, and is valid for original and subsequent owners. The warranty extension does NOT apply to any vehicle that has been previously declared a total loss, and/or sold for salvage by a financial institution or insurer, and/or has a branded or similar title under any states law.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

The sunroof may be inoperable and become stuck in the open, partially open, or closed position. This bulletin describes the procedure to replace the sunroof wind deflector and sunroof mechanisms with revised parts.

The sunroof may become inoperable and stuck in the open, partially open, or closed position. This bulletin describes the procedure to replace the sunroof wind deflector and sunroof mechanisms with revised parts.

This bulletin describes the procedure to repair the condition.

This bulletin describes the procedure to repair the condition.

rear sunroof.

rear sunroof.

rear sunroof.

the door glass area while driving.

(transmission clutch slip in gear above limit) listed on Page 2.

If you are servicing a vehicle with any symptoms listed below or DTCs (listed on Page 2) , follow the Service Procedure on Page 3. SYMPTOMS: Shifter System Malfunction displayed in the cluster Wont shift into or out of gear or wont shift out of Park Incorrect gear display in cluster and/or wont start

The current version of Google Maps has 10 times the data transmission compared to the previous version. As a countermeasure, an update with a frame skip logic has been added to resolve the data congestion with Google Maps.

or symptoms listed below, refer to the Service Procedure to diagnose the condition.

If you are servicing a vehicle with any symptoms or DTC listed below, follow the Service Procedure, Page 2.

on the instrument cluster when the turn signal is turned ON or the radio screen when transmission is in Reverse. The following conditions may occur; blurry image, line on the screen, fuzziness, or blue screen. This bulletin provides information to assist with troubleshooting the condition(s) above.

on the instrument cluster when the turn signal is turned ON or the radio screen when transmission is in Reverse. The following conditions may occur; blurry image, line on the screen, fuzziness, or blue screen. This bulletin provides information to assist with troubleshooting the condition(s) above.

This procedure is necessary to reduce the transmission learning time and improve the shift quality.

Service Procedure to measure shift engagement time.

OEM (new) and remanufactured automatic transmissions:

slipping more than 200 rpm in gear).

Hyundai has extended warranty coverage for the seat belt buckle under this condition to 15 years/150,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

At Hyundai, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, Hyundai is extending warranty coverage for the Seat Belt Buckle under this condition to 15 years/150,000 miles (whichever occurs first) from the date of original retail delivery or date of first use and is valid for original and subsequent owners.

Hyundai is extending warranty coverage for the seat belt buckle under this condition to 15 years/150,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Please note that any vehicles under 15 years/150,000 miles and within the original 5 years/60,000 miles are still subject to this warranty extension under TSB 25-BE-010H.

Follow the procedure in this TSB to inspect the concerning seat belt buckle(s) for abnormal symptoms with buckle insertion, ejection feeling, sound, or potential debris that influences operation. If any of the above symptoms are found, replace the seat belt buckle(s). Hyundai is extending warranty coverage for the seat belt buckle under this condition to 15 years/150,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Please note that any vehicles under 15 years/150,000 miles are covered by this TSB, even if vehicle is within original warranty of 5 years/60,000 miles.

Hyundai is extending warranty coverage for the seat belts under this condition to 10 years/100,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the service procedure in this TSB to visually inspect and replace seat belts that are twisted due to excessive space in the D-ring.

Hyundai is extending warranty coverage for the seat belts under this condition to 10 years/100,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the service procedure in this TSB to visually inspect and replace seat belts that are twisted due to excessive space in the D-ring.

At Hyundai, we are committed to providing vehicles of outstanding quality and value. In an effort to meet this commitment, Hyundai is extending the warranty coverage for the seat belts under this condition to 10 years/ 100,00 miles from the date of original retail delivery or date of first use and is valid for original and subsequent owners.

Hyundai is extending warranty coverage for the seat belts under this condition to 10 years/100,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the service procedure in this TSB to visually inspect and replace seat belts that are twisted due to excessive space in the D-ring.

Hyundai is extending warranty coverage for the seat belts under this condition to 10 years/100,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the service procedure in this TSB to visually inspect and replace seat belts that are twisted due to excessive space in the D-ring.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

headrest(s).

headrest(s).

headrest(s).

Hyundai Palisade (LX2) AWD vehicles.

Hyundai Palisade (LX2) AWD vehicles.

This bulletin provides information for troubleshooting the third row seat.

This bulletin provides information on how to inspect and if necessary repair the condition.

certain 2019-2021MY vehicles at California dealers. This reporting is mandated by CARB (California Air Resources Board).

This bulletin provides information on how to inspect and if necessary repair the condition.

recommended safe chemical products.

chemical products.

certain 2019-2020MY vehicles at California dealers. This reporting is mandated by CARB (California Air Resources Board). Data is no longer submitted to Hyundai by datasheet and dealer email. Data is sent electronically by GDS when the procedure of this bulletin is followed.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

Hyundai?s commitment to improving product quality includes monitoring all customer and dealer activities through a Launch Quality Monitoring Process (LQMP) for a minimum of 100 days after the launch of a new vehicle. The goal is to improve new model vehicle quality and proactively react to the Voice of the Customer (VOC).

This may be caused by worn self-leveling rear shock absorbers. Hyundai is extending the warranty coverage for the self-leveling rear shock absorbers to 10 years/120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Technical Service Bulletin (TSB) 25-SS-004H provides instructions on the replacement of the self-level rear shock absorbers.

This may be caused by worn rear self-leveling shock absorbers. Hyundai is extending the warranty coverage for the self-leveling rear shock absorbers to 10 years/120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners.

This may be caused by worn self-leveling rear shock absorbers. Hyundai is extending the warranty coverage for the self-leveling rear shock absorbers to 10 years/120,000 miles from the date of original retail delivery or date of first use (whichever occurs first) and is valid for original and subsequent owners. Follow the procedure in this bulletin to identify the source of the noise and replace the self-leveling rear shock absorbers.

side view mirror hole, and glass run on certain Palisade vehicles experiencing wind and/or whistling noise while driving.

side view mirror hole, and glass run on certain Palisade vehicles experiencing wind and/or whistling noise while driving.

and newer Santa Fe (TMA), 2021MY and newer Santa Fe Hybrid (TM HEV), 2022MY and newer Santa Fe Plug-In Hybrid (TM PHEV), and 2019MY and newer Palisade (LX2) vehicles equipped with surround view monitoring (SVM) system.

2020-2021MY Palisade (LX2) and Santa Fe (TMa) vehicles equipped with surround view monitoring (SVM) system.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

Procedure to diagnose the condition.

diagnosing and conducting alignment-related repairs for all models and model years.

compressor pulley and hub assembly. Follow the procedure outlined in this bulletin to inspect and determine whether to replace the compressor assembly or only the pulley using the service kit.

compressor pulley and hub assembly. Follow the procedure outlined in this bulletin to inspect and determine whether to replace the compressor assembly or only the pulley using the service kit.

Follow the procedure outlined in this bulletin to inspect and determine whether to replace the compressor assembly or only the pulley using the service kit.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

compressor pulley and hub assembly. Follow the procedure outlined in this bulletin to inspect and determine whether to replace the compressor assembly or only the pulley using the service kit.

intermittent BCW malfunction indicator light. The affected vehicles include: Certain 2020 MY Palisade (LX2) Equipped with BCW