2019 Hyundai Nexo TSBs

This bulletin provides the service procedure to inspect and when necessary perform the power tailgate spindle wire harness revision.

This bulletin provides the service procedure to inspect and when necessary perform the power tailgate spindle wire harness revision.

tailgate may experience a nonoperational condition. This campaign provides service procedures to inspect and when necessary, perform the power tailgate spindle wire harness revision.

tailgate spindle wire harness update.

This bulletin provides the service procedure to inspect and when necessary perform the power tailgate spindle wire harness revision

State of Charge (SOC) at or below 50%. A 30 Day alert - vehicle has not started and reported an SOC in 30 days.

by running the GDS Battery Claim App. The App must be run right after an incident battery is removed from the vehicle or after a battery charge is completed which qualifies for a warranty. It must be run at any time between RO open and close dates.

and P315300, both Hydrogen Pressure Sensor 1 and Hydrogen Pressure Sensor 2 must be replaced with an updated part.

If a vehicle is in service for any maintenance or repair, including the DTCs listed above, both Hydrogen Pressure Sensor 1 and Hydrogen Pressure Sensor 2 must be replaced with an updated part.

from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the BSD/BCW zone and turns on the BSD/BCW warning lamp for the driver. The warning lamp starts blinking, along with an audible sound, when the driver turns on the turn signal lamp to enter the lane where another vehicle is driving.

and safe environmental recycling using Hyundai?s authorized vendor Kinsbursky Brothers Intl. (KBI).

Whenever the left or right side BCW module is being replaced, it is required to perform the variant coding procedure. If the variant coding procedure is not performed, a DTC C1743 (S/W mismatch) will be triggered.

and safe environmental recycling using Hyundai?s authorized vendor Kinsbursky Brothers Inc. (KBI).

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

combination lamp, daytime running lamp (DRL), or fog lamp. This TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes or during normal driving operation.

load carrying capacity information indicated on tire placards when vehicle weight has been increased before retail sale. This limit is the lesser of 1.5% of GVWR or 100 pounds. If the total added weight exceeds the lesser of the limit, a label must be added to the driver-side B-pillar within 25mm (1 inch) of the original tire placard.

Pump Motor or Internal Controller Malfunction) resulting in reduced engine power due to cracking in the stack coolant pump rotor molding. This bulletin provides replacement procedures related to the stack coolant pump.

Perform the procedure outlined in this bulletin to fulfill the Bearing Clearance Test inspection requirements to determine next required steps.

combination lamp, daytime running lamp (DRL), or fog lamp. The TSB illustrates the various causes of condensation inside the lamp assembly. Lamp assembly replacement is NOT necessary in most cases. This condition can be eliminated by turning on the lamps with the engine running for several minutes, or during normal driving operation.

Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.

certain 2019-2021MY vehicles at California dealers. This reporting is mandated by CARB (California Air Resources Board).

recommended safe chemical products.

chemical products.

certain 2019-2020MY vehicles at California dealers. This reporting is mandated by CARB (California Air Resources Board). Data is no longer submitted to Hyundai by datasheet and dealer email. Data is sent electronically by GDS when the procedure of this bulletin is followed.

Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizon's communication network. If you are experiencing issues with remote commands, or other Bluelink services, please see the instructions below to reestablish the connection via the AVN pinhole reset method.

This may be due to an irregular disconnection on Verizons communication network. Follow the procedure in this TSB to reestablish the connection via the AVN pinhole reset method.

eliminate unnecessary FCA (Forward Collision Avoidance) malfunction warning messages.

The update is to revise the vehicle?s IEB (Integrated Electronic Brake) diagnostic logic to eliminate unnecessary FCA (Forward Collision Avoidance) malfunction warning messages.

For all wheel/tire balance claims, the Tire Balance Data Sheet must be fully completed including imbalance and Road Force Variation (RFV) data. The Data Sheet can be found at the end of this bulletin.

maximize tire life and performance.

diagnosing and conducting alignment-related repairs for all models and model years.

This service campaign provides the procedure to install an Audio Video Navigation (AVN) software update, which corrects this condition.

condition in which the radio presets may reset during AVN start up.

2. This bulletin presents guidelines to inspect for common Android Auto and Apple CarPlay connection conditions. 3. This bulletin provides physical differences between the USB 2.0 port and USB 3.0 port.

Management Unit (HMU) on certain NEXO (FE) vehicles. This update revises the logic for Malfunction Indicator Light (MIL) ON related to the FCU and HMU.

Hydrogen storage Management Unit (HMU) on certain NEXO (FE) vehicles. This update includes logic revision for Malfunction Indicator Light (MIL) ON related to the FCU and HMU.

If the protective cover is not removed correctly, there is a possibility of the rubber insert and rail spring becoming partially separated on the inner side of the wiper blade, which could lead to poor wiping performance and/or possible scratching of the windshield glass. Follow the procedure in this bulletin to properly remove the windshield wiper blade protective cover on all new wiper blades.

It provides a barrier between the paint and contaminants, such as rail dust, acid rain, and industrial fallout. In rare cases, the paint can become clouded under the PPF. These spots are the result of moisture trapped between the PPF and the paint.

OEM (new) and remanufactured automatic transmissions:

compressors equipped in hybrid electric vehicles, plug-in hybrid electric vehicles, and electric vehicles.